Page 1
BSG7....GB
Instructions for use
Page 2
2
Page 3
Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Disposal information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Your vacuum cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Setting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Vacuuming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
When the work is done . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Changing the dust bag and filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Replacement parts and accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
3
Page 4
4
Page 5
Please keep this instruction manual.
Please pass on this instruction manual if you pass this
vacuum cleaner on to a new owner.
Intended use
This vacuum cleaner is intended for domestic use and
not for commercial use.
This vacuum cleaner should only be used in accordance
with this instruction manual.
The manufacturer will not accept any responsibility for
damage caused by improper use or incorrect operation.
Therefore, please note the following points.
The vacuum cleaner must only be operated with:
Manufacturer’s original dust bags
Manufacturer’s replacement parts, accessories
and optional accessories
The vacuum cleaner is not to be used for:
Vacuuming persons or animals
Vacuuming up:
– insects or spiders
– hazardous, sharp-edged, hot or burning substances
– damp or liquid substances
– highly flammable or explosive substances and
gases
– Ash, soot from tiled stoves and central heating
systems
Do not use the vacuum cleaner if it is damaged.
Unplug the power cord from the mains if a fault is
detected.
To prevent you from being exposed to risks, vacuum
cleaner repairs and the fitting of replacement parts
must only be carried out by the authorised aftersales service.
The vacuum cleaner should be protected from
outside weather conditions, moisture and sources of
heat.
The vacuum cleaner is not suitable for use on
building sites.
=> Vacuuming up building rubble could damage the
vacuum cleaner.
Switch off the vacuum cleaner when it is not in use.
At the end of its life, the vacuum cleaner should be
disposed of in an appropriate manner.
For safety reasons, vacuum cleaners with a power
rating of more than 2,000 W are fitted with a
temperature safety switch.
This automatically switches off the vacuum cleaner if
it is blocked and overheating. Unplug the vacuum
cleaner from the mains and make sure that the
nozzles, suction pipe and hose are not blocked and
check whether the filter needs replacing.
Having cleared the blockage, leave the vacuum
cleaner to cool down for at least one hour. It can
then be switched back on again.
Safety information
This vacuum cleaner complies with the recognised
rules of technology and the relevant safety regulations.
We confirm compliance with the following European
directives: 89/336/EEC (amended by Directives
91/263/EEC, 92/31/EEC and 93/68/EEC). 73/23/EEC
(amended by Directive 93/68/EEC).
Always observe the information on the rating plate
when using the vacuum cleaner and connecting to
the power supply.
Never use the vacuum cleaner without a dust bag
fitted.
=> This can damage the vacuum cleaner.
Only allow children to use the vacuum cleaner under
strict supervision.
Keep the vacuum cleaner away from the face when
using tools and tubes.
=> Risk of injury.
Never carry the vacuum cleaner by the power
cord.
Fully extend the power cord when using the vacuum
cleaner continuously for several hours.
When disconnecting the appliance from the mains,
pull the plug, not the power cord.
Do not pull the power cord around sharp corners or
allow it to become trapped.
Unplug the vacuum cleaner from the mains before
carrying out any work on it.
Disposal information
Packaging
The packaging is designed to protect the vacuum
cleaner from being damaged during transportation.
It is made of environment-friendly materials and can
be recycled.
Dispose of packaging that is no longer required at an
appropriate recycling point.
Used vacuum cleaners
Used vacuum cleaners still contain many recyclable
materials.
Therefore, please take used vacuum cleaners to your
retailer or recycling centre so that they can be
recycled.
For current disposal methods, please enquire at your
appliance dealership or local council.
Please note
!
Only connect the appliance to a socket that is
protected by at least a 16 amp fuse.
If a fuse should blow when you switch on the vacuum
cleaner, this may be because other electrical
appliances which have a high current draw are
connected to the same power circuit.
To prevent the fuse from tripping, select the lowest
power setting before switching the vacuum cleaner
on, and increase the power only once it is running.
5
Page 6
Your vacuum cleaner
6
5
4
3
2*
7
8
9
10
11
12
13
14
15
16
17
1
1 Adjustable floor tool with locking collar
2
Hard-floor brush with
3 Turbo brush for floor
4
Turbo brush for upholstery
5 Telescopic tube with adjusting sleeve and locking
collar
6 Handle
7 Flexible hose
8 Hard furnishings brush
9 Upholstery nozzle
10 Crevice nozzle
11 Dust bag change indicator
12 Accessories compartment
13 Cover
6
locking collar
*
18
212324
22
14 Filter foam
15 Filter holder for micro-hygiene filter
16 Electronic slide control
17 Swing handle; also used as an ON/OFF button and
carrying handle
18 Power cord
19 ON/OFF button
20 Parking aid
21 Exhaust filter
22 Storage aid (on underside of unit)
23 Motor protection filter
24
MEGAfilt®SuperTEX dust bag
Only for model BSG72233GB
*
20 19
Page 7
Setting up
CLICK!
Before using for the first time
Push the handle onto the flexible hose until it engages.
Insert the flexible hose connector into the opening on the vacuum cleaner
until it engages.
Push the handle into the telescopic tube until it engages.
Push the telescopic tube straight into the connecting piece of the floor
tool until it engages.
7
Page 8
Setting up
Release the telescopic tube by moving the adjusting sleeve/sliding switch
in the direction of the arrow and adjust the tube to the required length.
Take the mains plug, pull the mains cable to the required length and insert
the plug into a wall socket.
To switch your vacuum cleaner on, press the On/Off button in direction of
arrow.
The button can also be pressed using the swing handle.
8
Page 9
Vacuuming
min max
The required suction power can be selected infinitely variably by adjusting the
slide control.
Lowest
suction range:
For vacuuming delicate fabrics, e.g. curtains.
Low
suction range:
For cleaning carpets and when there is little dirt.
Medium
suction range:
For vacuuming durable floor coverings, hard floors and for heavily
soiled surfaces.
High
suction range: :
For vacuuming stubborn dirt and very heavily soiled surfaces.
Adjusting the floor tool:
Rugs and carpets =>
hard floors =>
Vacuuming with accessories
(attach to handle or suction pipe as required).
Crevice nozzle
For cleaning crevices and corners.
9
Page 10
Vacuuming
a
a) Upholstery nozzle
For cleaning upholstered furniture, curtains, etc.
b) Furniture brush
For vacuuming picture frames, books, delicate
furniture, etc.
b
Small accessories that you do not need can be stored in the vacuum
cleaner lid.
Turbo brush for upholstery
Connect the turbo brush to the handle.
Brush vacuuming
Please note
!
Only brush vacuum using lower suction levels, i.e. no higher than
medium power on the vacuum cleaner.
Maintenance
Switch off the vacuum cleaner and unplug the power cable before carrying
out any maintenance work. Remove the turbo brush from the handle.
10
Page 11
Vacuuming
Cut off any wrapped around hair or threads using a pair of scissors.
Then vacuum up the threads and hair using the corner nozzle.
Turbo brush for floor
Fit the turbo brush onto the suction pipe.
Vacuuming with the brush
Please observe!
!
Only vacuum using the brush on full suction power, i.e. max.
performance of the vacuum cleaner.
The turbo brush has the possibility to change the rotation speed of the
brush from a maximum »A« to a complete stop »B«
Moving the slider a little from »A« to »B«permits an optimum cleaning
effect for the different floor coverings (long or short pile carpets).
Closing completely the fan inlet (position »B«)it is possible to use the
device as a normal floor nozzle.
11
Page 12
Vacuuming
Only brush the fringes in the direction of the arrow.
Maintenance
Always switch off the vacuum cleaner and pull out the plug before
performing any maintenance work. Remove the turbo brush from the
suction / telescopic pipe.
Cut off any wrapped around hair or threads using a pair of scissors.
Then vacuum up the threads and hair using the corner nozzle.
The lower cover can be removed forcleaning the fan and the fan chamber.
Closed chamber.
To remove the cover act to the two little side wings pushing them toward
you,lift up with a light rotation.
12
Page 13
Vacuuming
Open chamber
Insert the front lips to reassembly the lower cover
Push the cover up to click.
Please observe!
!
Never operate the turbo brush without the lower cover or with the
lower cover not well locked.
13
Page 14
Vacuuming
*
*
*
Hard-floor brush
For vacuuming hard floor coverings (tiles, parquet flooring, etc.)
Push the telescopic tube into the connecting piece of the hard-floor brush
until it engages.
Press on the locking collar and pull out the telescopic tube to disconnect.
Cleaning the hard-floor brush
Vacuum from below to clean the brushes.
*
14
If they are very dirty, e.g. with hair wrapped around them, remove both
brush rollers from the hard-floor tool. To do so, lever the rollers out
from the side of the guide using a screwdriver, or similar object.
Only for model BSG72233GB
*
Page 15
Vacuuming
CLICK!
*
Cut through threads and hairs wound round the rollers using scissors.
Vacuum threads and hairs with the crevice nozzle.
*
*
After cleaning, insert the brush rollers back into the hard-floor tool and
click into place.
Only for model BSG72233GB
*
15
Page 16
Vacuuming
CLICK!
CLICK!
*
The tool connector can be removed if the vacuum channel becomes
blocked.
Place the brush with the suction opening facing upwards, push the
guide at the side of the wheel slightly outwards and pull the tool con
nector upwards and away from the brush.
*
*
When refitting the connector, make sure that it is correctly seated and
that it engages correctly in the guide.
*
16
Only for model BSG72233GB
*
Page 17
Vacuuming
You can use the parking aid on the back of the appliance during short
pauses in vacuuming after switching off the vacuum cleaner.
To do this, slide the catch on the floor tool into the groove on the back of
the appliance.
The vacuum cleaner can also be carried using the swing handle when
negotiating obstacles such as stairs.
17
Page 18
When the work is done
Rewinding the power cord.
Tug the power cord and let go (the cable automatically rewinds).
To store or transport the vacuum cleaner, use the storage aid on the
underside of the cleaner.
Stand the vacuum cleaner up on its end.
Slide the catch on the floor tool into the groove on the underside of the
appliance.
To remove the flexible hose, press the release button and pull out the
hose.
To release the connection, press the unlatching sleeve and pull the handle
out.
18
Page 19
When the work is done
Press on the locking collar and pull out the telescopic tube to disconnect.
19
Page 20
Changing the dust bag and filters
Replacing the dust bag
If the dust bag change indicator is completely yellow when the floor tool is
lifted from the floor and the highest suction power is selected, the dust
bag must be changed, even if it is not yet full. In this case it is essential to
change the dust bag due to the type of material it contains.
First check that the nozzle, suction pipe and flexible hose are not blocked,
as this would also lead to the dust bag change indicator being triggered.
Open the cover by moving the locking lever in the direction of the arrow.
®
Seal and remove the MEGAfilt
SuperTEX dust bag by pulling on the tab as
shown.
Place a new
MEGAfilt®SuperTEX
dust bag in the holder and close the dust
bag compartment lid.
®
Caution: The cover only closes when a MEGAfilt
SuperTEXdust bag
has been inserted.
20
Page 21
Changing the dust bag and filters
Cleaning the motor protection filter
The motor protection filter should be cleaned at regular intervals by
tapping it or washing it out.
Open the dust compartment cover.
Remove the motor protection filter in the direction of the arrow.
Empty the motor protection filter by tapping it.
If the motor protection filter is very dirty, wash it out.
Leave the filter to dry for at least 24 hours.
After cleaning, insert the motor protection filter in the machine and
close the dust compartment cover.
21
Page 22
CLICK!
Changing the dust bag and filters
*
*
**
Replacing the exhaust filter
You must replace the exhaust filter in your vacuum cleaner once a year.
Replacing the HEPA filter
If your vacuum cleaner is equipped with a HEPA filter, this should be replaced
once a year.
Open the dust bag compartment lid
Unlock the HEPA filter by pushing the locking tab in the direction of the
arrow and remove it from the vacuum cleaner.
Insert the new HEPA filter and click it into place.
After vacuuming up fine dust particles, shake out the motor
protection filter to clean it and replace the micro-hygiene filter,
activated carbon filter or HEPA filter if necessary.
Only for model BSG72233GB
*
Replacing the micro active carbon filter
Open the dust bag compartment lid.
Release the filter holder by moving the locking lever in the direction of
the arrow.
Remove the micro active carbon filter.
22
**
Inser t the new micro active carbon filter into the vacuum cleaner and
clip into place.
Only for model BSG72225GB
**
Page 23
CLICK!
Changing the dust bag and filters
For using the attached micro - filters please insert them into the filter
holder which is enclosed.
Open the dust bag compartment lid
Unlock the exhaust filter by pushing the locking tab in the direction of
the arrow and remove it from the vacuum cleaner.
Place one of the micro-hygiene filters and the foam in the filter holder.
Insert the filter holder into the vacuum cleaner and clip into place.
23
Page 24
Changing the dust bag and filters
Replacing the micro-hygiene filter
The micro hygiene filter should be changed when starting a new pack of
bags.
Open the dust bag compartment lid
Unlock the filter holder by pushing the locking tab in the direction of
the arrow.
Remove the foam and micro-hygiene filter.
Place a new micro-hygiene filter and the foam in the filter holder.
Insert the filter holder back into the vacuum cleaner and click it into
place.
Care
Always switch off the vacuum cleaner and disconnect the power cord from the mains before cleaning the appliance.
The vacuum cleaner and plastic accessories can be cleaned with a commercial plastic cleaner.
Do not use a scourer, glass-cleaning agent or multipurpose cleaning product.
Never immerse the vacuum cleaner in water.
The dust compartment can, if necessary, be cleaned with a second vacuum cleaner or simply wiped with a dry cloth
or dusting brush.
Subject to technical modifications.
24
Page 25
Replacement parts and accessories
Typ GXL
Replacement filter pack BBZ52AFGXL
Contents: 5 filter bags with lock
http://www
Textile dust bag (permanent dust bag) BBZ10TFG
Reusable bag with Velcro fastener.
HEPA filter (Class H12) BBZ152HF
Recommended for allergy sufferers. Ensures ver y clean exhaust air.
Replace annually.
1 micro-hygiene filter
.dust-bag-bosch.com
Micro active carbon filter BBZ193MAF
Combination of micro filter and active carbon filter. Combats unpleasant
odours. Replace annually.
TURBO-UNIVERSAL®brush for upholstery BBZ42TB
All-in-one brushing and vacuuming of upholstered furniture, mattresses,
car seats, etc. Especially suitable for picking up pet hair. The brush roller
is driven by the air flow through the vacuum cleaner.
No separate electrical connection is needed.
25
Page 26
Replacement parts and accessories
TURBO-UNIVERSAL®brush for floors BBZ102TBB
All-in-one brushing and vacuuming of shallow-pile rugs and carpets and all
hard floor coverings. Especially suitable for picking up pet hair. The brush
roller is driven by the air flow through the vacuum cleaner.
No separate electrical connection is needed.
Hard floor brush BBZ123HD
For vacuuming hard floors (parquet flooring, tiles, terracotta, etc.)
Washing brush BBZ103WD
Suitable for use on all hard floors, such as parquet, laminate, stone,
wooden floorboards, tiles, etc. (test the moist cleaning cloths on an
inconspicuous area before using on hard floors which require particular
care).Removes large particles of dirt while the moist cleaning
cloth cleans the floor at the same time.
26
Page 27
272829
Page 28
Page 29
Page 30
Conditions of guarantee
For this appliance the guarantee conditions as set
out by our representatives in the country of sale
apply. Details regarding same may be obtained
from the dealer from whom the appliance was
purchased. For claims under guarantee the sales
receipt must be produced.
30
Page 31
This appliance is labelled in accordance with European
Directive 2002/96/EG concerning used electrical and
electronic appliances (waste electrical and electronic
equipment - WEEE). The guideline determines the
framework for the return and recycling of used
appliances as applicable throughout the EU.
31
Page 32
323334
Page 33
Page 34
Page 35
35
Page 36
Printed on recycled paper
A
9000 372 856 A
The design of this product is environment-friendly.
All plastic parts are identified for recycling purposes
Loading...