Boland Communications BVB User Manual

User Manual

1 of 26

BVB Series

High-Definition Serial Digital Interface

Multi Format LCD Monitor

User Manual

User Manual

2 of 26

CAUTION ...................................................................................................................................................... 3

FEATURES ................................................................................................................................................... 5

CONTROLS, INDICATORS AND CONNECTIONS ..................................................................................... 6

MENU BASIC OPERATION ....................................................................................................................... 10

PICTURE MENU ......................................................................................................................................... 12

AUDIO MENU ............................................................................................................................................. 16

DISPLAY MENU ......................................................................................................................................... 17

GPI MENU ................................................................................................................................................... 20

SETUP MENU ............................................................................................................................................. 21

INFO MENU ................................................................................................................................................ 23

INPUT SUPPORT MODE ............................................................................................................................ 23

MECHANICAL DIMENSION ....................................................................................................................... 26

User Manual

3 of 26

Caution

WARNING:

To reduce the risk of electric shock does not remove cover (or back). No user serviceable parts inside.
Refer servicing to qualified service personnel. To prevent fire or shock hazard, do not expose the rear of
the set to rain or moisture. Do not rub or strike the Active Matrix LCD with anything hard as this may
scratch, mark, or damage the Active Matrix LCD permanently.

Unauthorized tampering with the inside of the monitor invalidates the warranty.
The manufacturer shall not warrant for any damage caused by improper maintenance and/or repair. Work
by third parties.
Important safeguards for you and your new product:
Your product has been manufactured and tested with your safety in mind. However, improper use can
result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built
into your new product, please read and observe the following safety points when installing and using your
new product and save them for future reference.

All operating and use instructions should be followed.

The safety and operating instructions should be retained for future reference.

All warnings on the product and in the operating instructions should be adhered to.

Disconnect the unit from the electricity supply before cleaning. Do not use abrasive cleaners. Use a damp
cloth for cleaning.

Do not use this apparatus near water.

A product and cart combination should be moved with care. Quick stops, excessive force and uneven
surfaces may cause the product and cart combination to overturn.

Do not use attachments not recommended by Boland as they may cause hazards.

Do not block any of the ventilation openings.
Install in accordance with the manufacturer’s instructions.

This product should be operated only from the type of power source indicated on the marking label. If you
are not sure of the type of power supply to your home, consult your supplying dealer.

This product is equipped with a three-wire grounding-type cord. This is a safety feature. Do not defeat the
safety purpose of the grounding-type cord.

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords at plugs, convenience receptacles and
the point where they exit from the product.

Before operating the set, please read this manual carefully.

Read Instructions
Follow Instructions

Retain Instructions

Heed Warnings

Cleaning

Water and Moisture

Transporting Product

Attachments

Ventilation

Power Sources

Power Lead Polarization

Power Cord Protection

Outdoor Cable Grounding

User Manual

4 of 26

Caution

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is
grounded so as to provide some protection against voltage surges and built-up static charges. A “face

plate” also needs to be installed with an isolating capacitor to prevent any damage from static.

For added protection for this product during a lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will
prevent possible damage to the product due to lightning and power-line surges.

An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to avoid contact with such power lines or circuits, as
contact with them might be fatal.

This product must be earthed properly to comply with the safety regulations in the country of use. If you
are unsure of these regulations, please consult a qualified electrician.

Do not attempt to service this product yourself as opening or removing covers may expose you to
dangerous voltages or other hazards. Refer all servicing to qualified service personnel. If the Set does not
operate properly, switch it off and call your dealer.

Isolate this product from the mains supply and refer servicing to qualified service personnel under the
following conditions:

Upon completion of any service or repairs to this product, ask the service technician to perform safety
checks to determine that the product is in proper operating condition and the front seal is intact.

The product should be mounted on a wall only as recommended in the instructions.

This set operates on an AC supply; the voltage is as indicated on the label on the Manual. This appliance
must be earthed at all times through the chassis as well as through the power lead.

Lightning

Power Lines

Earthing the product

Servicing

Damage Requiring Service

If the power-supply cord or plug is damaged.
If the glass front has been damaged.
If there is ingress of water between the glass and the LCD screen.
If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a qualified technician to restore the
product to its normal operation.
If the product has been dropped or the cabinet has been damaged.
If the product exhibits a distinct change in performance.

Safety Check

Mounting

Power

User Manual

5 of 26

Features

This product is the multi-format Digital LCD Panel to display various kinds of digital video input signal as
HD/SD-SDI/DVI/HDMI Digital and analog signal such as Composite/S-Video/RGB/PC-RGB/ Component.

This is also High Definition Broadcasting Monitor which can make it available to do output of stable video
signal with the menu of considering convenient user interface and the easy control for brightness and
color, and by EQ function of HD-SDI input part.

• HD/SD SDI 2Input / 2Output.

• WAVEFORM / Vector Scope / Time code Display.

- Dual waveform display available

• 16 ch Audio Lever Meter Display. (SDI only)

• Analog & Digital Signal Audio Lever Meter Display.

- Lever Meter Position display selectable

• Dual Link MODE & 1080p 60 Compatible

• Closed Caption (Analog Signal only): CEA608, 708

• H/V Delay.

• Audio Disembedder & Internal Speaker & Headphone out & Monitor out

• Color Temperature – User, VAR, 9300K, 6500K, 5400K, 3200K

• Over Scan/Zero Scan/Under Scan/Pixel to Pixel

• PIP (Picture In Picture)/PIP Blend

• Tally LED function (Green/Red/AMBER)

• Integrated DVI (HDCP) function.

• HDMI (HDCP) function.

• Supports VESA DDC2B and a subset of VESA standards.

• Single board is suitable for mounting behind an LCD panel.

• Supported RS-232C, RS-422.

• Supported External GPI Control (RJ-45).

• OSD: Graphic based OSD, 7 Languages (UNICODE System).

• LCD Dimming Control

- Manual Dimming Level Control.

• UMD

• Auto Calibration

• 10bits 3D LUT Color Calibration (BT.709, SMPTE-C, EBU, NTSC, D-Cinema)

• ETHERNET: Network System Controller / Update

: CA-210, CA-310 (Minolta), K-10 (Klein)

User Manual

6 of 26

Controls, Indicators and Connections

MENU

F5

SEL/INPUT

ADJUST

SPEAKER_R

DOWN

F6

F4
F3

SID 2

DVI

LED

STANDBY

SPEAKER_L

SID 1

Composite

HDMI

F1
F2

IR

UP

SDI 1 OUT

CVBS2/Y/G/Y IN

CVBS3/Pb/B/C IN

CVBS1/Pr/R IN

DVI

HDMI

RS-232 OUT

RS-232 IN

SDI 2 OUT

SDI 2 IN

SDI 1 IN

CVBS1/Pr/R OUT

CVBS2/Y/G/Y OUT

CVBS3/Pb/B/C OUT

AUDIO OUT

AUDIO IN

HEADPHONE

RS422 IN

RS422 OUT

LAN UPDATE

DC 12V

ETHERNET

GPI

BVB17 Front

BVB17 Rear

User Manual

7 of 26

Controls, Indicators and Connections

MENU

F5

SEL/INPUT

ADJUST

SPEAKER_R

DOWN

F6

F4
F3

SID 2

DVI

LED

STANDBY

SPEAKER_L

SID 1

Composite

HDMI

F1
F2

IR

UP

SDI 1 OUT

CVBS2/Y/G/Y IN

CVBS3/Pb/B/C IN

CVBS1/Pr/R IN

DVI

HDMI

RS-232 OUT

RS-232 IN

SDI 2 OUT

SDI 2 IN

SDI 1 IN

CVBS1/Pr/R OUT

CVBS2/Y/G/Y OUT

CVBS3/Pb/B/C OUT

AUDIO IN

AUDIO OUT

HEADPHONE

RS422 IN

RS422 OUT

ETHERNET

GPI

DC 12V

BVB24 Front

BVB24 Rear

User Manual

8 of 26

Controls, Indicators and Connections

Front Keys Operations

 STANDBY
Power ON/OFF Button. This button is operated after being pressed about 3 seconds.

 SDI 1 / SDI 2
Select SDI 1/ SDI 2 source directly

 Composite
Select ANALOG source directly( ‘CVBS1’ ->‘CVBS2’ ->‘CVBS3’)

 DVI
Select DVI source directly

 HDMI
Select HDMI source directly

 FUNCTION 1 ~ 6
Executes functions of user selected
(Undefined, Scan, Marker, Level Meter, Waveform, Aspect, H/V Delay, Time Code, Color Only, Audio
Group, Audio Channel, Audio mute, Still image, Caption, False Color, Aspect/Area Marker, PIP func
& Input, Zoom, Gamma Select, WFM Line Select)

 MENU
Activates main OSD menu
Navigates higher menu in main OSD menu
Exits OSD menu

 DOWN
Decreases sound volume of speaker
Decreases values of user menu in main OSD menu
Executes function (by OSD help commands) in main OSD menu

 UP
Increases sound volume of speaker.
Increases values of user menu in main OSD menu
Executes function (by OSD help commands) in main OSD menu

 SEL/INPUT
Activates OSD menu of input source selecting
Changes input source by selecting
Executes functions (by OSD help commands) in main OSD menu
Activates child menu

 ADJUST
Adjust Picture Menu (Brightness -> Contrast -> Color -> Sharpness->Phase & Tint)
Turn Right (with ‘UP' button is same)
Turn Left (with ‘DOWN' button is same)

User Manual

9 of 26

Controls, Indicators and Connections

PIN NO

Description

1

GND

2 , 3

4

+ 12V

1 2 3

4

REAR Panel

 SDI 1/SDI 2 IN
HD SDI / SD SDI Input

 SDI 1/SDI 2 OUT
SDI 1, SDI 2 Loop Out

 RS-232C IN
Update /Auto color calibration

 DVI-I
DVI-I Type Digital / Analog PC-RGB Video Input

 HDMI
High Definition Multimedia Input

 CVBS1/Pr/R In
CVBS 1, Component Pr, GBR(SOG sync) R Input

 CVBS2/Y/G/Y In
CVBS 2, Component Y, GBR(SOG sync) G, S-Video Y Input

 CVBS3/Pb/B/C In
CVBS 3, Component Pb, GBR(SOG sync) B, S-Video C Input

 AUDIO IN
DVI-I/Component/GBR/CVBS1,2,3/S-Video Sound Input

 AUDIO OUT
AUDIO MONITOR OUT

 ETHERNET
Network System Control/ Firmware Upgrade

 GPI
GPI 1 ~ 7 Control Port

 RS422 IN/OUT
Monitor System Control

 DC 12V IN

User Manual

10 of 26

MENU Basic Operation

In this menu system, there are several ways to customize the menu settings provided.
Most menus consist of three levels to set up the options, but some require greater depth for the variety of
settings. If you press the MENU button, only the first and second level of the menu system will appear on
the monitor screen. The third level can be displayed by pressing SEL/INPUT. If a menu has more than
three levels, the pop-up dialogue box will be displayed as the fourth or fifth level.

To show and remove the Menu

Press the MENU button to display the menu. A second press of the MENU button will take you back to
monitor viewing.

To go to the next level

Press SEL/INPUT button.

To go back to the previous level

Press MENU button

Typical Menu Operation

1. Press MENU button: The main menu will appear.

2. Use UP/DOWN button to select the desired menu option (icon).

3. While the desired menu option is selected, press SEL/INPUT to move to the second level.

4. Use UP/DOWN button to select the second menu option.

5. Press SEL/INPUT to move to the third level: Some menu options require additional steps.

6. Press MENU to return to the previous menu to return to monitor viewing.

Turning On the Monitor

1. First, connect power cord correctly. At this moment, the monitor switches to standby or power on mode.
In standby mode, in order to turn monitor on, press the ST-BY button.

2. Select the viewing source by using SEL/INPUT button on Keypad in front of monitor

Volume Adjustment

1. Press the UP/DOWN button on Keypad.

2. If you want to switch the sound off, press the FUNCTION (Audio mute) button.

3. You can cancel this function by pressing the FUNCTION (Audio mute) or volume control button.

User Manual

11 of 26

MENU Basic Operation

On Screen Menus Language Selection

- Display -> OSD Set -> Language

- The menus can be shown on the screen in the selected
language.

- Supported Language: English, Spanish, Portuguese, German,
French, Italian

How to Select Video Source by OSD

1. Press the SET/INPUT button and then UP/DOWN button to select each video source.

2. Press the SET/INPUT button to go to desired video source.

3. If Input Name is enabled, The SET/INPUT button goes into input name edit mode instead of selecting
source.

User Manual

12 of 26

PICTURE MENU

Video Menus of each Input modes

< Video (NTSC) Picture menu> < PC Picture menu> < SDI, HDMI Picture menu>

Adjust

- Adjust the values of Brightness, Contrast, Color, Tint and
Sharpness directly from -50 to 50
Contrast, Brightness, Sharpness, Color (All Sources), Tint
(without PC, DVI, HDMI, Component), Phase (Component).

Color Temperature Control

- For Setting the Color temperature or adjusting RGB Gain/Offset value directly

- User (User setting RGB gain value), VAR(3200K ~ 11000K), Often used value(11000K, 9300K, 6500K,
5400K,3200K) and 3D LUT Calibration value(D65 – 6504K/C-6774K/D-Cinema 6302K)

-Color Space: Native/BT.709/SMPTE-C/EBU/NTSC/D-Cinema

SCAN

1. Over Scan – 95% input size and fit the selected display size

2. Zero Scan – 100% Input size and fit the selected display size

3. Under Scan – 105% Input size and fit the selected display
size

4. Pixel to Pixel – Display size is an input size. If input resolution
is bigger than panel size, fit the panel size

User Manual

13 of 26

PICTURE MENU

Aspect Ratio

Zoom

- For setting the aspect ratio.

- Full Screen: The images are displayed with a panel size.

- Full Screen, 16:9, 4:3, 14:9, 13:9, 1.85:1, 2.35:1: The images
are displayed with each aspect ratio.

- Function-key operate Rotation, Full Screen, 16:9, 4:3, 14:9,
13:9, 1.85:1, 2.35:1

- AFD function Added

- PC mode: Full Screen & 4:3 only

- Can see the enlarged picture by (2X, 3X, 4X, 5X) ratios.

- If user select the Zoom 2X, can see the below yellow box in
picture.

- Press Select or Enter button, user can see the enlarged
picture.

- Menu key escape the zoom mode.

Picture Option

 I/P Mode



Line Doubler/inter-Field/Field Merge function on/off

 Gamma Select



Gamma Level Select (0.8 ~ 3.0)

 Back Light



Inverter dimming Level select (0~100)

 Color Only



Mono Color/Blue only Function on/off

- Mono color: For selecting monochrome images.

- Blue Only: Images have only blue color expect red and green color

 False Color



False Color: on/off

 Patterns



Auto Run, 100% Color Bars, 75% Color Bars, Luma, RGB, White, Black, RED, Blue, Green

 HV Delay



Off/ / H / V / H+V

 Output Range



Normal (16~235)/Full (0~255)

 Noise Reduction

-Noise Reduction on/off. (NR is for Video signal (HD-SDI, CVBS, S-Video and Y.Pb.Pr) & DTV timing.

 NTSC Setup(Only Video mode)

- IRE value under NTSC mode between 0 IRE and 7.5 IRE.

User Manual

14 of 26

PICTURE MENU

SDI 1

SDI 2

HDMI-DVI

PC_YPbPr_RGB_YC_CVBS

SDI 1

X O O

O

SDI 2

O X O

O

HDMI-DVI

O O X

O

PC_YPbPr_RGB_YC_CVBS

O O O

X

PIP

POP1

POP2

PIP (Picture IN Picture)

- Watch two programs or source at the same time. And set up PIP size and position.

 PIP on/off

 Input Source

- PIP input Source can operate with different signal and type.

- Analog (CVBS 1, 2, 3, Y.Pb.Pr, GBR, PC) inputs + Digital (DVI, HDMI) + SDI (SDI1, SDI2) inputs

-SDI + SDI input PIP
Ex) AV + S-Video (X), DVI + SDI (O), PC + DVI (O), SDI1+SDI2 (O)

- PIP MATRIX TABLE

- Control PIP function On/Off.

 Aspect Ratio

- Choose PIP size of Small/POP1/POP2

 Position

- Choose the pip position on the each corner of the pane

 PIP Blend

-Blend to PIP size of Small(0~100)

 PIP Swap

- Using Swap option, you can exchange two programs or source at the same time.

User Manual

15 of 26

PICTURE MENU

PC Menu

Dual Link Mode (SDI only)

- Only operate PC input mode

- Select Auto-adjust and adjust Phase, HV position, Frequency

- Auto-Adjust automatically set the optimum values of Phase,
HV position and Frequency.

-Selects X768 native PC video timings.
(Auto/1024x/1280x/1360x/1366x)

-Dual Link Mode select.
(Auto/Off/RGB444/YCbCr444/YCbCr422)

Peaking Filter

-Peaking Filter: Peaking Filter On/Off.

-Peaking Color: Red/Blue/White/Violet.

-Peaking Level: 0~100.

User Manual

16 of 26

AUDIO MENU

Audio Output

Audio Selection

-PIP & W/F Double mode only. Select the Main or Sub.

SDI out

 SDI Gr/Ch

- Audio output Group source select. (Group1, 2, 3, 4)

- Audio output Channel source select. (Channel1~16, Channel1/2,3/4,5/6,7/8,9/10,11/12,13/14,15/16 off)

 SD2 Gr/Ch

- Audio output Group source select. (Group1, 2, 3, 4)

- Audio output Channel source select. (Channel1~16, Channel1/2,3/4,5/6,7/8,9/10,11/12,13/14,15/16 off)

- Select Internal Speaker out. (Auto/SDI1/SDI2/HDMI/Line in)

-SDI Audio output Group & Channel source select

Volume

- Adjust the speaker or headphone Volume level.

User Manual

17 of 26

DISPLAY MENU

Marker

 Aspect

 Area

- Area: Draw dotted line Marker on screen in case of images. (16:9 95/93/90/88/80%, 4:3
95/93/90/88/80%, EBU Action 16:9/14:9/4:3, EBU Graphic 16:9/14:9/4:3)

 Center Maker

- “+” Marker on center of screen

 Aspect L. Color

-Marker Line Color Select. (WHITE, YELLOW, BLUE, RED, BLACK)

 Area L. Color

-Area Line Color Select. (WHITE, YELLOW, BLUE, RED, BLACK)

 Line Width

- Marker line thickness setting. (0~10)

 Custom Marker

-The user wants Marker size setting. (Below panel size)

- 16:9, 4:3, 14:9, 13:9, 1.85:1, 2.35:1, 1.85:1&4:3, Custom fitted
panel size marker on screen.

Waveform

 Enable

- Off / Y+VT / Y+Cb+Cr/ G+B+R /Double

 Key Format

- Press the W/F button to display the WAVEFORM Mode.
(Rotation, Y+VC, Y+Cb+Cr, G+B+R, Double)

 Line Select

- Select line WAVEFORM & Vector Scope display.

 Line Number

-Line select: Input Resolution size.

 Line Display

-off/on/5 sec

Level Meter

- Display the audio level meter on screen in SDI input.

- Audio level meter cannot display with OSD.

User Manual

18 of 26

DISPLAY MENU

 Type

-Pair: Respectively Channel with right and left display

-Group: Respectively group display

 Position

- Level Meter Position selects. ( )

 Scale

Time code

 Transparency

- Disable blending Time code background with video image. (0%, 25%, 50%, 75%, 100%)

 DVITC Line

-Auto, Line 1 ~ 31

- Level Meter Scale mode selects.
(Digital/Nordic/BBC/EBU/DIN/Expanded DIN/SMPTE VU/EBU
VU/France VU)

 Enable

- Time code Display (off/LTC/DVITC, SDI only)

 Size

-Time code size select. (Small, Middle, Large)

 Position

- Time code display position selects (L-T, C-T, R-T, L-B, C-B, R­B)

Caption

OSD Set

 Timeout

- OSD gone time setting. (3~200)

 Caption

-608 Line21, 608 ANC, 608 Transcoded, 708 mode Select

 608 Caption

-608 Caption mode Select. (C/C1, C/C2, C/C3, C/C4, TEXT1,
TEXT2, TEXT3, TEXT4, OFF)

 708 Caption

-708 Service mode Select. (Service 1/Service 2)

 Language

-Select a language for the menus to appear in. (English,
Spanish, Portuguese, German, French, Italian)

 Position

- L-T, R-T, C, L-B, R-B

 Transparency

- Disable blending OSD background with video image.

User Manual

19 of 26

DISPLAY MENU

UMD

Channel-012

Tally Red

Channel-012

Tally Green

Channel-012

U.M.D

 UMD

- UMD display on/off

 Character

- UMD Character Select

 Position

- UMD display position select. (L-T, C-T, R-T, L-B, C-B, R-B)

 FG Color

- UMD Character color Select (RGB_255_192_128_0_Transpareut)

 BG Color

- UMD BG color Select (RGB_255_192_128_0_Transpareut)

Input I.D.

 Input ID

- source Message display.

 ID Style

- select “Input Format”/”Custom Label”

 Input Label

- Display user made name instead of input source name on source OSD and message OSD.

Video Range

-Range Check: Range Check on/off.

-Y Max: Maximum luminance level.

-Y Min: Minimum luminance level.

-C Max: Maximum chroma level.

-C Min: Minimum chroma level.

-Color: Black/Blue/Red/Green

-Grid: Grid line on/off

-Blink: Y/C Min-Max to blink.(0~7)

User Manual

20 of 26

Remote MENU

GPI Function

Description

Undefined

Not set (no function allocated)

Tally R, Tally G

For lighting up the Red or Green tally lamp.

Marker On/Off

Displays the marker.

Function 1~6

Activates FUNCTION 1~6 buttons

Scan

Over Scan/Zero Scan/Under Scan/ Pixel to Pixel

Aspect

Sets the aspect ratio of the images

Waveform

Activates WAVRFORM & Vector Scope (SDI

Only)

Aspect Marker

Marker size Select.

Area Marker

Area Marker size Select.

Center Marker

Displays the center marker.

Input CVBS 1,2,3, Input G.B.R, Input SDI

1, Input SDI 2, Input Y.Pb.Pr , Input PC ,

Input DVI, Input HDMI

Switches the input source.

Menu Key, Enter Key, Up Key, Down Key

Left Key, Right Key

Use the key function by GPI.

GPI 7 : Power Key(Fixed)

GPI Control & GPI#

- For allocating functions to particular GPI pins.

- When remote control operations are to be performed using the GPI Controller.

- GPI Control: GPI function Enable/Disable

- GPI 1 ~ 7

User Manual

21 of 26

SETUP MENU

Function1&2 button

Description

Undefined

Not set (no function allocated)

Scan

Over Scan/Zero Scan/Under Scan/ Pixel to Pixel

Marker

Marker on/off

Level Meter

Level Meter on/off

Waveform

Waveform on/off

Aspect

Sets the aspect ratio of the images

H/V Delay

H Delay -> V Delay -> HV Delay -> off

Time Code

Time Code on/off.

Color Only

Execute Mono color or Blue Only

Audio Group

Select the extract the embedded audio group in SDI input.

Audio Channel

Select the extract the embedded audio channel in SDI input.

Audio Mute

Toggles sound status of speaker/headphone in mute.

Still image

Toggles picture status between motion and still image.

Caption

Caption on/off.

False Color

False Color on/off

Aspect / Area Marker

Aspect/ Area Marker Select

PIP func & Input

PIP func & input Select

Zoom

Zoom function on/off

Gamma Select

Gamma Select

WFM Line Select

WFM Line select function on/off

Setup Load & Setup Save

- Setup Load: Load user saved values or default value

- Setup Save: Save user setting values at user 1, 2, 3.

Function Switch

- Function 1~6 : Select the function to be allocated to the FUNCTION
1~6 buttons

Control

- Front LED on/off

-Power, up and down key is only worked, if Local enable is off.

- Select the controller of local or remote. If remote controller is
selected, both local (front key) and remote are worked.
However select local, local key only operated.

 Auto Key Lock

- If it does not work 10 minutes to lock automatically. Key button is operated after being pressed about 2
seconds

 Front LED

 Local Enable

 Remote Enable

User Manual

22 of 26

SETUP MENU

 Source Key (Front “Input” Button/ Remote Controller “Source” Button)

-Menu: Select the input signals to the input menu OSD.

-Rotate: Press Button to rotate the input source.

 Auto Source

- When there is no input signal, Auto Source change.

Communication

IP Config

 Type

-Select the Communication: RS-422 or Lan

 Baud Rate _ 422 Baud Rate

- 2400/4800/9600/19200/38400/57600/115200

 Serial Protocol_422/Lan Protocol

-Basic / TSL 5.0 / TSL 4.0 / RDU/ Extension

 ID (01~99)

- If control each Board, must set ID numbers of each Board

 Load Network Settings

-ETHERNET cable connected after “Enter”. (ID/IP
Address/Gateway/Subnet Load)

 DHCP

-DHCP on/off (Manual IP settings – DHCP on)
* “Apply” enter all settings after.

Screen Saver

 Blue Screen

- Enables screen saver functions to avoid panel burning.

 BG Gray

- Select gray level on besides display picture. (0~7)

 Power Save

- DPMS (Display Power Management Signaling) Power Save
Mode.

Fan Control

 Fan Control

- Internal Fan Controls driving option by temperature sensor Auto / force on / force off
 Active Temp

- Adjusts fan driving temperature by Celsius degree. It works only when the Fan Control setting is Auto.

 Hysteresis

- Adjusts fan driving hysteresis temperature by Celsius degree. (1~10℃)

 Shutdown

- For a monitor protection is above of 75℃, Power Off.

Sync Check Period

- Sync Check Period at when switching the input signal (10 ~ 300 ms)

User Manual

23 of 26

Info MENU

Items

Specifications

Supported
Signals

Serial Digital Interface

HD SDI- 2.970Gbps

SD HDI- 270Mbps

HDMI
DVI-I (DVI+VGA_IN)

H Frequency Range : 20~82 kHz

V Frequency Range : 55 ~ 90 Hz

Maximum resolution :1920x1080 60Hz

Maximum pixel rate : 162 MHz

DTV mode support : 720P, 1080i, 1080p

ANALOG RGB

H Frequency Range : 20~82 kHz

V Frequency Range : 55 ~ 90 Hz

Maximum resolution : 1920x1080 60Hz

Maximum pixel rate : 162 MHz

DTV mode support: 720P/1080i/1080p

SOG sync support

ANALOG Component
(DTV/DVD)

1080p/1080i/720P/480i/576i/480P/576P

CVBS

NTSC/PAL/SECAM

SMPTE-428.1M

2048x1080P(24/25)

SMPTE-425M(3G)

1920x1080P(50/60)

SMPTE-260M

1920x1035i(60/59.94)

SMPTE-259M

1920x1080i(50)

SMPTE-274M
1920x1080i (50/59.94/60)

1920x1080P (30Psf/25Psf/24Psf/30/25/24)

SMPTE-296M

1280x720P (24/25/30/50/59.94/60)

SMPTE-125M

480i(59.94)

ITU-R BT.601

576i(50)

Input Support Mode

Support Signals

- Model, H/W Version, FPGA,F/W Release, Operating Time,
Cal. ID

Support Timings

 SDI Input

User Manual

24 of 26

Input Support Mode

Section

Resolution

H Frequency( kHz )

V Frequency( Hz )

Pixel Frequency( MHz )

Comment

PC

640x400

37.861

85.08

31.5

640x350

31.469

70.087

25.175

640x350

37.861

85.08

31.5

640x480

31.469

59.94

25.175

640x480

35.000

66.667

30.24

640x480

34.940

69.884

28.513

640x480

37.861

72.809

29.765

640x480

37.500

75.0

31.5

640x480

43.269

85.008

36.0

640x480

45.540

90.0

37.889

720x400

31.469

70.087

28.322

720x400

37.927

85.039

35.5

800x600

35.156

56.25

36.0

800x600

37.879

60.317

40.0

800x600

43.764

70.02

45.513

800x600

48.077

72.188

50.0

800x600

46.875

75.0

49.5

800x600

53.674

85.061

56.25

800x600

56.880

90.0

60.065

832x624

49.726

74.551

57.284

1024x768

48.780

60.001

64.11

1024x768

48.363

60.004

65.0

1024x768

56.476

70.069

75.0

1024x768

57.703

72.039

78.476

1024x768

60.241

74.927

81.724

1024x768

60.030

75.029

78.75

1024x768

68.677

84.997

94.5

1024x768

72.810

90.0

100.187

1152x864

53.700

60.0

81.624

1152x864

62.932

69.924

96.663

1152x864

67.500

75.0

104.993

1152x870

68.681

75.062

100.0

1152x900

61.846

66.0

94.787

1152x900

72.713

76.047

105.561

1280x720

47.760

60.0

74.481

1280x720

52.500

70.0

89.040

1280x720

54.072

72.0

91.706

1280x720

56.400

75.0

95.654

1280x768

60.150

75.0

102.977

1280x960

60.000

60.0

102.104

1280x960

59.640

60.0

102.104

 PC & DVI Input

User Manual

25 of 26

1280x1024

63.337

59.978

108.18

1280x1024

63.981

60.02

108.0

1280x1024

64.754

60.06

108.992

1280x1024

63.600

60.0

108.883

1360x768

47.700

60.0

84.700

1600x1200

75.000

60.0

162.000

DTV

720x480

15.735

59.94

13.500

Interlaced

720x576

15.735

50.0

13.595

Interlaced

720x480

31.469

59.94

25.175

720x576

31.250

50.0

26.566

1280x720

44.964

59.94

74.176

1280x720

37.500

50.0

60.466

1920x1080

33.750

60.0

74.25

Interlaced

1920x1080

28.125

50.0

70.723

Interlaced

1920x1080

31.250

50.0

72.000

Interlaced

1920x1080

67.5

60

148.5

Progressive

User Manual

26 of 26

Mechanical Dimension

BVB17

BVB24