Bock Water heaters Gas Water Heaters User Manual

Power Direct Vent

Energy Saver

Gas Water Heaters

80% Thermal Efficient

 80 to 100 gallons/300,000 to 360,000 BTU

 Co-axial vent

 Sealed combustion

 Low NOx construction available

 Electronic ignition and controls

 Non-CFC foam insulation

 Automatic blower motor

 Glass-lined storage tank

 Hand hole cleanout

 Sediment reduction system

 Standard and ASME construction

 NSF kit available

 Complies with SCAQMD low NOx requirements

 Design certified by CSA International (formerly AGA/CGA)

 3-Year Limited Tank/1-Year Limited Parts Warranties

Energy Saver

Power Direct Vent

B

1 1/2” FRONT OUTLET
2” REAR OUTLET

E

F

3/4” GAS
CONNECTION

1 1/2” FRONT INLET
2” REAR INTLET

44 5/8

D

C

A

G

21”

Gas Water Heaters

This product is available from:

DIMENSIONS (INCHES) SHIPPING WEIGHT

1ST HR

DEL GAL
@ 100° F

RISE

MODEL

NUMBER

80PDV-300 80 300,000 347 728 291 208 63-7/8 28-1/4 65-3/4 51-1/2 20-3/4 14 69-1/2

100-PDV-360 100 360,000 419 873 349 249 72-7/8 28-1/4 74-3/4 60-1/2 20-3/4 14 74-1/2

STORAGE

(GAL)

RATED
INPUT

(BTU/HR)

To order Natural Gas use the sux "NA", for LP use the sux "XA"; Example: 80PDV-300-NA

For ASME Construction add the sux "A" at the end; Example: 80PDV-300-NA-A

For LowNOx compliance to meet SCAQMD requirements, place an "LN" in the model number; Example:
80PDVLN-300-NA

RECOVERY GPH
@ DEGREE RISE

A

HEIGHTB DIA.

C

TOP
WATER
CONN.

D

FRONT

HOT

CONN.

FRONT

COLD

CONN.

E

CONN.

G

F

TOP

GAS

VENT

HEIGHT

(LN) LowNOx Burners

80PDVLN-300 280,000 BTUH 679 272 194

100PDVLN-360 335,200 BTUH 812 325 232

WATER
CONN.

1-1/2 (T&F)

1-1/2 (T&F)

GAS

CONN.

DIA.

3/4 1 665 740

2 (R)

3/4 1 735 815

2 (R)

RELIEF
VALVE
OPEN.

RECOVERY GPH @

40° F 100° F 140° F

STD

(LBS)

DEGREE RISE

ASME

(LBS)40° F 100° F 140° F

T=Top, F=Front, R=Rear

These models meet or exceed the Thermal Eciency and Standby Loss Requirements of ASHRAE 90.1b current standard.

115V A.C. Required

T&P Valve, Brass Drain Valve, Diaelectric Fittings, Magnesium Anode Rods: Factory Installed

Pressures (all): Working Pressure, 150 psi; Tested Pressure, 300 psi

Warning: Installation should be in accordance with all national and/or local codes. In the absence of local codes, refer to NFPA 54 or ANSI Z21.10.1.

Caution: The recommended maximum hot water termperature setting for normal residential use is 120°F. Bock recommends a tempering valve or anti-scald

valve be installed and used according to the manufacturer’s directions to prevent scalding.

www.bockwaterheaters.com

110 South Dickinson Street , Madison, Wisconsin 53703

Toll Free 800.794.2491•Phone [phone]●Fax [phone]

80028 Rev 6/08