Page 1
HEX70HDU-KIT
Introduction
HEX70HDU-KIT QUICK REFERENCE GUIDE
Quick Reference Guide
Our HEX70HDU-KIT extender kit is an industry leading 4K HDBaseT™ multi-format
solution delivering HDMI, USB-C and DisplayPort™ up to lengths of 70m at 1080p
(40m at 4K 60Hz 4:4:4) over a single CAT cable. The HEX70HDU-KIT provides
enhanced features including local HDMI input on the HDBaseT™ Receiver for
additional source input, Web GUI for control and configuration, auto display
control, audio breakout, bi-directional IR pass-through and EDID management.
The HEX70HDU-KIT has multiple control options including buttons on both TX
and RX units, IR, RS-232 and TCP/IP.
FE ATURES:
• Advanced HDBaseT™ technology oering distirbution of video and audio over a single CAT cable
• Features 1 x HDMI, 1 x USB-C and 1 x DisplayPort™ input on the HDBaseT™ Transmitter with manual or auto source
selection
• Features a local HDMI input on the HDBaseT™ Receiver for connection of a source device local to the display
• Supports 4K 60Hz 4:4:4 UHD video up to 40m
• Extends HDMI 1080p up to a distance of 70m over a single CAT cable
• Supports all known HDMI audio formats including Dolby TrueHD, Atmos, and DTS-HD Master Audio transmission
• Supports USB Type C up to 4K UHD 60Hz 4:4:4* (DP1.2 with 60W charging capability
• Supports DisplayPort up to 4K UHD 60Hz 4:4:4, 4K 30Hz 4:4:4 DP1.2
• Audio breakout to analogue L/R audio** and Coaxial digital (S/PDIF) outputs concurrently
• Supports Bi-directional PoC to power extenders from either Transmitter or Receiver end
• Bi-directional IR pass-through
• Auto display on / o feature allowing control of display at the HDBaseT™ Receiver via CEC, RS-232, or Relay
• Web interface module for control and configuration of HEX70HDU-KIT
• Control via front panel, IR, RS-232 and TCP/IP
• Advanced EDID and HDCP management
*USB-C video support is limited to 4K 60Hz 4:2:0 when charging feature is activated by the source device
**Analogue audio breakout supports 2ch PCM only
contact: support@blustream.co.uk | support@blustream.com.au
01
Page 2
TX Panel Description
HEX70HDU-KIT QUICK REFERENCE GUIDE
1
4
2
5 6
3
8 9
7
10
11
1 Power status indicator
2 Local HDMI input signal link indicator
3 DisplayPort™ input signal link indicator
4 USB-C input signal link indicator
5 Remote (RX) HDMI input signal link indicator
6 Input / Auto select button - press to change source,
hold for 3 seconds to enable / disable auto signal
sense switching
7 IR control port (to Blustream 5V 3.5mm IR receiver or
IR control device)
8 IR IN (to Blustream 5V 3.5mm IR receiver)
9 IR OUT (to Blustream 5V 3.5mm IR emitter)
q RS-232 - 3-pin Phoenix connector for RS-232 pass
through, or device control by RS-232 commands
12
13 14 15 16 17 18 19
w USB Upgrade port
e HDBaseT™ output
r HDMI input - connect to source equipment
t DisplayPort™ input - connect to source equipment
y USB-C input - connect to source equipment
u EDID DIP switch (UP=0, DOWN=1)
i TCP/IP (RJ45) – connect to LAN for TCP/IP control
Default IP of the HEX70HDU-KIT is 192.168.0.200
o Reset HEX70HDU to default IP settings
p Power port – use included 24V/5A DC adaptor to
power the device
RX Panel Description
1 2 3
4 5 6 7
1 Power status indicator
2 Local HDB a seT ™ input signal link indicator
3 Local HDMI input signal link indicator
4 Auto input signal link indicator
5 Input / Auto select button - press to change source,
hold for 3 seconds to enable / disable auto signal
sense switching
6 IR IN (to Blustream 5V 3.5mm IR receiver)
7 IR OUT (to Blustream 5V 3.5mm IR emitter)
8 RS-232 - 3-pin Phoenix connector for RS-232 pass
through, or device control by RS232 commands
9 USB Upgrade port
8
9
10
11
12 13 14 15 16
q HDBaseT™ input
w HDMI input - connect to local source equipment
e HDMI output - connect to display equipment
r Coaxial digital audio output – extract audio from the
selected input signal
t L/R analogue audio outputs (5-pin Phoenix)
extracted audio from the selected input signal.
Note: Input signal must be PCM 2ch audio
y Relay - 3-pin Phoenix connector
u Power port – Use included 24V/5A DC adaptor to
power the device
02
www.blustream.com.au | www.blustream.co.uk
Page 3
HEX70HDU-KIT QUICK REFERENCE GUIDE
RS-232 Configuration & Control
The RS-232 ports can be used for configuration / control of the product, as well as pass through of RS-232 commands
between the serial ports of the HEX70HDU-TX and RX. By default, the Transmitter unit is allocated for control and
feedback of switching, however this can be changed to the Receiver if required.
The default RS-232 communication settings are:
Baud rate: 57600
Data bit: 8
Stop bit: 1
Parity bit: none
For the complete RS-232 and TCP/IP command list please see the HEX70HDU-KIT User Manual - available to download
from the Blustream website.
EDID Control
EDID (Extended Display Identification Data) is a data structure that is used between a display and a source to negotiate
the best audio and video resolutions that are supported in the system. A global EDID of the HEX70HDU-KIT can be
configured using a combination of DIP switch settings (see below), or using IP / RS-232 commands. Please refer to the
HEX70HDU-KIT User Manual - available to download from the Blustream website.
Global EDID Settings
DIP switch position ‘0’ = O / Up
DIP switch position ‘1’ = On / Down
EDID DIP Switches
[DIP] = 0000: HDMI 1080p @60Hz, Audio 2ch PCM (default)
[DIP] = 0001: HDMI 1080p @60Hz, Audio 5.1ch PCM/DTS/DOLBY
[DIP] = 0010: HDMI 1080p @60Hz, Audio 7.1ch PCM/DTS/DOLBY/HD
[DIP] = 0011: HDMI 1080i @60Hz, Audio 2ch PCM
[DIP] = 0100: HDMI 1080i @60Hz, Audio 5.1ch PCM/DTS/DOLBY
[DIP] = 0101: HDMI 1080i @60Hz, Audio 7.1ch PCM/DTS/DOLBY/HD
[DIP] = 0110: HDMI 4K @60Hz 4:2:0, Audio 2ch PCM
[DIP] = 0111: HDMI 4K @60Hz 4:2:0, Audio 5.1ch PCM/DTS/DOLBY
[DIP] = 1000: HDMI 4K @60Hz 4:2:0, Audio 7.1ch PCM/DTS/DOLBY/HD
[DIP] = 1001: HDMI 4K @60Hz 4:4:4, Audio 2ch PCM
[DIP] = 1010: HDMI 4K @60Hz 4:4:4, Audio 5.1ch PCM/DTS/DOLBY
[DIP] = 1011: HDMI 4K @60Hz 4:4:4, Audio 7.1ch PCM/DTS/DOLBY/HD
[DIP] = 1100: DVI 1920x1080 @60Hz, Audio None
[DIP] = 1101: DVI 1920x1200 @60Hz, Audio None
[DIP] = 1110: EDID Passthrough
[DIP] = 1111: Soware Controlled EDID (set EDID via TCP/IP or RS-232)
Web GUI Control
The HEX70HDU-KIT features an in-built Web GUI which can be used for control and configuration of the product.
Default Username is: blustream Default Password is: 1234 Default IP Address is: 192.168.0.200
For further information please see the HEX70HDU-KIT User Manual - available to download from the Blustream
website.
Auto On / O Display Control
The HEX70HDU-KIT can be programmed to automatically power on / o a display connected to the HDBaseT™
Receiver output via CEC, RS-232 or Relay. Please refer to the HEX70HDU-KIT User Manual - available to download from
the Blustream website for more details.
contact: support@blustream.co.uk | support@blustream.com.au
03
Page 4
HEX70HDU-KIT QUICK REFERENCE GUIDE
Specifications
HEX70HDU-TX Transmitter
• Video Input Connectors: 1 x HDMI Type A, 19-pin, female; 1 x USB Type C; 1 x DisplayPort™
• Video Output Connectors: 1 x HDBaseT™ RJ45 connector
• RS-232 Serial Port: 1 x 3-pin Phoenix connector
• TCP/IP Control: 1 x RJ45, female
• IR Input Ports: 2 x 3.5mm stereo jack
• IR Output Port: 1 x 3.5mm mono jack
• EDID: 4-pin DIP switch
• Product Upgrade: 1 x Micro USB, female
• Local Power Input: 1 x 24V/5A 4-PIN DIN connector
• Casing Dimensions (W x H x D): 180mm x 23.5mm x 155mm
HEX70HDU-RX Receiver
• Video Input Connectors: 1 x HDMI Type A, 19-pin, female; 1 x HDBaseT™ RJ45 connector
• Video Output Connectors: 1 x HDMI Type A, 19-pin, female
• Audio Output Connectors: 5-pin Phoenix connector (2ch balanced / unbalanced analogue audio); 1 x RCA (S/PDIF)
• RS-232 Serial Port: 1 x 3-pin Phoenix connector
• Relay Control: 2 x 3-pin Phoenix connectors
• IR Input Port: 1 x 3.5mm stereo jack
• IR Output Port: 1 x 3.5mm mono jack
• Product Upgrade: 1 x Micro USB, female
• Local Power Input: 1 x 24V/5A 4-PIN DIN connector
• Casing Dimensions (W x H x D): 180mm x 23.5mm x 155mm
• Operating Temperature: 32°F to 104°F (-5°C to +55°C)
• Storage Temperature: -4°F to 140°F (-25°C to +70°C)
• Shipping Weight: 2.3kg
• Power Supply: 24V/5A DC
NOTE: Specifications are subject to change without notice. Weights and dimensions are approximate.
Package Contents
• 1 x HEX70HDU-TX
• 1 x HEX70HDU-RX
• 1 x 24V/5A DC Power Supply
• 1 x IR Emitter
• 1 x IR Receiver
• 1 x RS-232 Control Cable
• 2 x Mounting Kits
• 1 x Quick Reference Guide
Acknowledgements
DisplayPort™ and the DisplayPort™ logo are trademarks owned by the Video Electronics Standards Association (VESA®)
in the United States and other countries.
04
www.blustream.com.au | www.blustream.co.uk
REVA5_HEX70HDU-KIT_QRG_260520
Loading...