Page 1
contact support@blustream.co.uk / support@blustream.com.au
HEX100CS-KIT QUICK REFERENCE GUIDE
HEX100CS-KIT
Quick Reference Guide
01
Our HEX100CS-KIT HDMI 2.0 4K 60Hz 4:4:4 (18Gbps) HDCP 2.2 HDBaseT™
extender set offers market leading features and outstanding value utilising
CSC technology. The product extends HDMI,Bi-directional IR & RS-232 and
Bi-directional PoH (PoE) up to lengths of 100m (4K 70m).The Transmitter
includes a HDMI loop-out for integrating local displays or cascading to
multiple devices. The Receiver features simultaneous analogue stereo and
digital coax audio breakout.
Introduction
FE ATU RE S:
• Advanced HDBaseT™ technology oering distribution of video and audio over a single CAT cable
• Advanced Color Space Conversion (CSC) supports HDMI 2.0 18Gbps specification including HDR
• Supports 4K 60Hz 4:4:4 UHD video up to 70m
• Extends HDMI 1080P video up to 100m
• Features 1x HDMI loop-out on HEX100CS-TX for integrating local displays or cascading to multiple devices
• Supports all industry standard video resolutions including VGA-WUXGA and 480i-4K
• Supports all known HDMI audio formats including Dolby TrueHD, Atmos and DTS-HD Master Audio transmission
• HDMI re-clocking on the HDBaseT™ Receiver to help solve HDMI HDCP, compatibility and handshaking issues
• HDMI audio breakout to analogue L/R audio and coaxial digital outputs concurrently
• Supports bi-directional RS-232 pass through
• Supports bi-directional IR pass through
• Supplied with Blustream 5V IR receiver and emitter
• Advanced EDID management
• HDCP 2.2 Support
IR OutIR In
Mod e
RS-232
IR OutIR In
DC 12 V
Pow er
HDB T Out
Upg rade
EDI D
0
3 2 1 0
1
IR Out IR In
RS-232
HDM I In HDM I Out
Lin k
Lin k
DC 12 V
Pow er
HDB T Out
Upg rade
EDI D
0
3 2 1 0
1
IR Out IR In
RS-232
Page 2
HEX100CS-KIT QUICK REFERENCE GUIDE
www.blustream.co.uk
02
Panel Description HEX100CS-RX
Panel Description HEX100CS-TX
1
2
1 Mode dip-switch - To switch RS-232 serial port
between pass-through and firmware update mode
2 RS-232 / serial connector
3 HDBaseT input
4 HDBaseT signal link indicator
5 DC 12V screw type connector
6 Power status indicator
9 HDMI input
q HDMI link indicator
w HDMI output
e HDMI link indicator
7 Coaxial digital output - de-embedded from HDMI input
8 Analogue audio Le/Right output (3.5mm stereo jack
de-embedded from HDMI input. Supports stereo
2CH PCM audio only
9 HDMI signal link indicator
q HDMI Output
w IR IN (to Blustream 5V 3.5mm IR receiver)
e IR OUT (to Blustream 5V 3.5mm IR emitter)
3 4 5 6 7
1 EDID DIP switch (UP=0, DOWN=1)
2 IR OUT (to Blustream 5V 3.5mm IR emitter)
3 IR IN (to Blustream 5V 3.5mm IR receiver)
4 RS-232 / Serial connector
5 USB Upgrade port - For future use
6 HDBaseT output
7 Power status indicator
8 DC 12V screw type connector
9 10 11 12
1 2 3 4 5 7 8 9 10 116 12
8
IR OutIR In
Mod e
RS-232
IR OutIR In
DC 12V
Powe r
HDBT O ut
Upgr ade
EDID
0
3 2 1 0
1
IR Out IR In
RS-232
HDMI I n HDMI O ut
Link
Link
DC 12V
Powe r
HDBT O ut
Upgr ade
EDID
0
3 2 1 0
1
IR Out IR In
RS-232
Page 3
contact support@blustream.co.uk / support@blustream.com.au
HEX100CS-KIT QUICK REFERENCE GUIDE
Understanding the Transmitter/Receiver status lights
03
EDID (Extended Display Identification Data) is a data structure that is used between a display and a source. This data is used by
the source to find out what audio and video resolutions are supported by the display. By pre-determining the video resolution
and audio format of the source and display device you can reduce the time needed for EDID hand shaking thus making
switching quicker and more reliable.
Configuration of extender EDID settings can be achieved using the product dip-switches on the end of the HEX100CS-TX. EDID
dip-switch settings are shown below.
EDID Control
Global EDID settings
Dip-switch position ‘0’ = O
Dip-switch position ‘1’ = On
The Blustream HEX100CS-KIT extender solutions include status LED indicators on both the Transmitter and Receiver
products to show all connections are active and to help diagnose possible problems.
Receiver:
• The HDMI signal link light will be o when there is no connection with a display/sink
• The HDMI link light will be on when there is an active connection with a display
• The HDBaseT link light will be o when there is no CAT cable/active HDBaseT connection on the RJ45 HDBaseT
input
• The HDBaseT link light will blink if there is an unstable connection between the Transmitter and Receiver
• The HDBaseT link light will be lit when a CAT cable is connected to the HDBaseT RJ45 output on the Transmitter
and an active connection is achieved with the Receiver.
Transmit ter:
• The Input HDMI signal link light will be o when there is no connection with a source device
• The Output HDMI signal link light will be o when there is no connection with a display/sink
• The Input HDMI link light will be on when there is an active connection with a source device
• The Output HDMI link light will be on when there is an active connection with a display/sink
• The HDBaseT link light will be o when there is no CAT cable/active HDBaseT connection on the RJ45 HDBaseT
output
• The HDBaseT link light will blink if there is an unstable connection between the Transmitter and Receiver
• The HDBaseT link light will be lit when a CAT cable is connected to the HDBaseT RJ45 output on the Transmitter
and an active connection is achieved with the Receiver
EDID Dip-switches
[DIP]=0000: HDMI 1080p@60Hz, Audio 2ch PCM
[DIP]=0001: HDMI 1080p@60Hz, Audio 5.1ch PCM/DTS/DOLBY
[DIP]=0010: HDMI 1080p@60Hz, Audio 7.1ch PCM/DTS/DOLBY/HD
[DIP]=0011: HDMI 1080i@60Hz, Audio 2ch PCM
[DIP]=0100: HDMI 1080i@60Hz, Audio 5.1ch PCM/DTS/DOLBY
[DIP]=0101: HDMI 1080i@60Hz, Audio 7.1ch PCM/DTS/DOLBY/HD
[DIP]=0110: HDMI 4K@60Hz 4:2:0+4K@30Hz 4:4:4, Audio 2ch PCM
[DIP]=0111: HDMI 4K@60Hz 4:2:0+4K@30Hz 4:4:4, Audio 5.1ch PCM/DTS/DOLBY
[DIP]=1000: HDMI 4K@60Hz 4:2:0+4K@30Hz 4:4:4, Audio 7.1ch PCM/DTS/DOLBY/HD
[DIP]=1001: HDMI 4K@60Hz 4:4:4, Audio 2ch PCM
[DIP]=1010: HDMI 4K@60Hz 4:4:4, Audio 5.1ch PCM/DTS/DOLBY
[DIP]=1011: HDMI 4K@60Hz 4:4:4, Audio 7.1ch PCM/DTS/DOLBY/HD
[DIP]=1100: DVI 1280x1024@60Hz, Audio None
[DIP]=1101: DVI 1920x1080@60Hz, Audio None
[DIP]=1110: DVI 1920x1200@60Hz, Audio None
[DIP]=1111: Soware Control EDID
DC 12 V
Pow er
HDB T Out
Upg rade
EDI D
0
3 2 1 0
1
IR Out IR In
RS-232
Page 4
HEX100CS-KIT QUICK REFERENCE GUIDE
www.blustream.co.uk
For the full Blustream HEX100CS-KIT User Manual please visit the dealer resource area of our website www.blustream.co.uk
04
Package Contents
Specifications
Maintenance
HEX100C S-KIT
• 1 x HEX100CS-TX and 1 x HEX100CS-RX
• 1 x 12V/2A DC power supply
• 1 x IR emitter (IRE)
• 1 x IR receiver (IRR)
• 2 x Mounting bracket sets
• 1 x Quick reference guide
Clean this unit with a so, dry cloth. Never use alcohol, paint thinner or benzene to clean this unit.
NOTE: Specifications are subject to change without notice. Weight s and dimensions are approximate.
HEX100C S-RX (when sold individually)
• 1 x HEX100CS-RX
• 1 x Mounting bracket set
HE X 100CS-TX
• Video input: 1x HDMI Type A, female
• Video output: 1x HDBaseT RJ45 connector
• 1x HDMI Type A, female
• RS-232 serial port: 1x DB9 female connector
• IR input: 1x 3.5mm stereo jack
• IR output: 1x 3.5mm mono jack
• EDID DIP switch: 4-pin
• Mounting kit included
• Dimensions excl connections (W x D x H):
143mm x 134mm x 22mm
• Shipping weight (Kit): 0.5 kg
• Power: 12V/2A DC, screw type connector
• Operating temperature: 32°F to 104°F (0°C to 40°C)
• Storage temperature: -4°F to 140°F (-20°C to 60°C)
HEX100C S-RX
• Video input: 1x HDBaseT RJ45 connector
• Video output: 1x HDMI Type A, female
• Audio output: 1x 3.5mm L/R analogue audio & 1x
digital coaxial (RCA)
• RS-232 serial port: 1x DB9 female connector
• IR input: 1x 3.5mm stereo jack
• IR output: 1x 3.5mm mono jack
• Mounting kit included
• Dimensions excl connections (W x D x H):
113mm x 124mm x 22mm
• Shipping weight (Kit): 0.4 kg
• Power: 12V/2A DC, screw type connector
• Operating temperature: 32°F to 104°F (0°C to 40°C)
• Storage temperature: -4°F to 140°F (-20°C to 60°C)
RevA1_QRG_HEX100CSKIT_180419_Print Layout
Loading...