Blue-White C-1500N User Manual
MODEL C-1500N
5300 Business Drive
Huntington Beach, CA 92649
USA
Phone: 714-893-8529 FAX: 714-894-9492
E mail: sales@blue-white.com or techsupport@blue-white.com
www.Blue-White.com
INJECTOR
®
D
IS
C
H
A
RG
E
L
IN
E
S
M
A
Y B
E
U
N
D
E
R
H
IG
H
P
R
E
S
S
U
R
E
. U
S
E
C
A
R
E
T
O
P
R
O
T
E
C
T
Y
O
U
RS
E
L
F
W
HE
N
D
IS
C
O
N
N
EC
T
IN
G
.
CA
UTI
ON
A
D
JU
ST
W
H
ILE RU
N
NIN
G
MIN
1
2
3
4
5
6
7
8
9
L
OO
S
E
N
T
H
E
L
OC
K
S
CR
E
W
TU
R
N
K
N
OB
T
O
D
E
S
I
R
E
D
S
E
T
T
I
N
G
R
E
-
T
I
G
HT
E
N
T
H
E
LO
C
K
S
C
R
E
W
M
A
X
CHEM-FEED
BLUE-WHITE INDUSTRIES
WESTMISNSTER
CA
92683
Blue-White
Industries, Ltd.
R
TABLE OF CONTENTS
SECTION HEADING PAGE
1 Introduction 2
2 Specifications 2
3 C-1500N Features 3
4 How to install the C-1500N 3
4.1 Mounting location 3
4.2 Electrical connections 5
4.3 How to install the tubing and fittings 6
5 How to operate the C-1500N 8
5.1 Adjusting the Pump Output - Standard Models 8
5.2 Adjusting the Pump Output - Fixed cycle timer Models 9
5.2 Measuring the pump’s output - volumetric test 9
6 How to maintain the C-1500N 9
6.1 Routine inspection and cleaning 9
6.2 How to clean the C-1500N 9
1.0 Introduction
Thank you for purchasing the C-1500N positive displacement metering pump.
The C-1500N is designed to inject chemicals into piping systems. All models are
equipped with a top mounted mechanical flow rate adjustment knob. Optional
on/off cycling timers are available.
The pump has been tested by NSF International for use with 12-½% Sodium
Hypochlorite.
CAUTION: This pump has been evaluated by ETL Intertek Testing Services for
use with water only. The factory performance tests the pump with water only.
2.0 Specifications
Maximum Working Pressure 125 psig / 8.6 bar*
o o
Maximum Fluid Temperature 130 F / 54 C
o
Output Accuracy +/- 10% of maximum (water @ 70 F, 0
psig, and 5’ suction lift)
o o
Ambient Temperature Range 14 to 110 F / -10 to 43 C
Enclosure NEMA 3R (IP 23) acceptable for outdoor
use
Duty Cycle Continuous
Maximum Viscosity 1,000 Centipoise
Maximum Suction Lift up to 10 ft. water
Power Requirements 115V60Hz 45 Watts
220V50Hz 45 Watts
230V60Hz 45 Watts
24V60Hz 45 Watts
Dimensions 9-1/16” high x 4-1/2” wide x 5-3/4” deep
Weight 7 lb.
C-1500N
Page 2
C-1500N
Page 3
3.0 C-1500N Features
!
Double-ball ceramic check valves.
!
PVDF (Kynar) valve assemblies.
!
Viton o-rings.
!
High outlet pressure capability of 125 PSIG.*
!
Easy access, top mounted mechanical feed rate adjustment.
!
Ball bearing supported motor drive shaft.
!
Permanently lubricated ball bearing motor.
!
20:1 adjustment turn down ratio.
!
Acceptable for outdoor use. (NEMA 3R; IP23)
!
Corrosion resistant Valox housing.
!
Easy servicing.
!
Includes suction tube foot valve & strainer, suction tube weight, suction tubing,
discharge tubing and injection fitting with internal back-flow check valve and
mounting hardware.
* Most models.
4.0 How To Install the C-1500N
Note: All diagrams are strictly for guideline purposes only. Always consult
an expert before installing the C-1500N into specialized systems.
The C-1500N should be serviced by qualified persons only.
4.1 Mounting Location
Choose an area located near the chemical supply tank, chemical injection point
and electrical supply. Although the pump is designed to withstand outdoor
conditions, a cool, dry, well ventilated location is recommended. Install the
pump where it can be easily serviced.
!
Mount the pump to a secure surface or wall using the enclosed hardware. Wall
mount to a solid surface only. Mounting to drywall with anchors is not
recommended.
!
Keep the outlet (discharge) tubing as short as possible. Longer tubing
increases the back pressure at the pump tube.
!
Do not mount the pump directly over your chemical container. Chemical
fumes may damage the unit. Mount the pump off to the side or at a lower
level than the chemical container.
!
Mounting the pump lower than the chemical container will gravity feed the
chemical into the pump. This “flooded suction” installation can reduce the
time required to prime the pump. Install a shut-off valve, pinch clamp or other
means to halt the gravity feed to the pump during servicing.
!
Your solution tank should be sturdy. Keep the tank covered to reduce fumes.
!
Be sure your installation does not constitute a cross connection with the
drinking water supply. Check your local plumbing codes.
Proper eye and skin protection must be worn
when installing and servicing the pump.
!
CAUTION
#10-32
FIG. 4.2 SWIMMING POOL INSTALLATION
FIG. 4.3 TYPICAL INSTALLATION
®
1. Strainer
Blue-White F-300
2. Circulation Pump
7. Injector
®
3. Filter
Blue-White C-1500N
4. Heater
8. Solution Tank
5. Check Valve
9. Injection Fitting
6. Flowmeter
10. Return Line
1
Pool
2
3
5
4 6
7
8
9
10
Discharge Tube
Pumping unit
Suction Tube
(vertical)
Chemical
Container
¼" & ½" NPT Injector
C-1500N
4-1/2”
9-1/16”
5-3/4”
FIG. 4.0 DIMENSIONAL DRAWING
FIG. 4.1 INJECTOR WALL MOUNTING
#10 Self-Tap
(2 X)
Wall Mount
Bracket
C-1500N
Page 4
Risk of chemical overdose. Be certain the
pump does not overdose chemical during
backwash and periods of no flow in the
circulation system.
!
WARNING
To prevent chemical overdosing, a flow switch
is recommended on the circulation system to
automatically stop chemical feed when there is
no return flow to the swimming pool or spa.
!
CAUTION
C-1500N
Page 5
4.2 Electrical Connections
4.2.1 Input Power Connections
Note: When in doubt regarding your electrical installation, contact a licensed
electrician.
The C-1500N is supplied with either a ground wire conductor and a grounding
type attachment plug (power cord) or a junction box for field wiring.
POWER CORD MODELS -To reduce the risk of electric shock, be certain
that the power cord is connected only to a properly grounded, grounding type
receptacle.
JUNCTION BOX MODELS -To reduce the risk of electric shock, be certain
that a grounding conductor is connected to the green grounding conductor
located in the junction box.
FIG. 4.4 WIRING DIAGRAM - STANDARD MODELS
AC
MOTOR
INPUT
VOLTAGE
115V 60Hz
HOT
LEADWIRE
NEUTRAL
LEADWIRE
GROUND
LEADWIRE
230V 60Hz
BLUE or YELLOW
BLUE
BROWN
RED
GREEN
GREEN
GREEN
MOTOR LEADWIRES
Neutral
Hot
Ground (green)
Earth Ground (green)
Common
Hot
AC
Input
Power
220V 50Hz
BLACK or YELLOW
BLACK or YELLOW
* Yellow leadwire : thermally protected motor
Black or Blue leadwire: standard impedance protected motor
*
*
*
24V 60Hz
WHITE
GREEN
BLUE
*
To prevent chemical overdosing,
disconnecting power to the circulation system
must also disconnect power to the pump.
!
CAUTION
SHOCK
!
WARNING
Risk of electric shock. Be certain to connect the
pump to the proper supply voltage. Using the
incorrect voltage will damage the pump and
may result in injury. The voltage requirement is
printed on the pump serial label.
Loading...