Page 1
HDE-8C DIN SERIES
QUICK GUIDE
STEP 1 - Connect the Inputs
H25 Receiver#1H25 Receiver
HD MPEG-2 Encoding
#2
8xDIN (Component Video)
(8 HD Programs)
H25 Receiver
#8
8xIP*
EAS
* Model dependent
4xQAM*
• Locate the blank receiver labels in the plastic bag supplied with the encoder. Number each label
with UNIT numbers 1 through 8.
• Find the receiver ID number label on the rst receiver. Write the last 4 digits of the ID on label #1
(RX1_####__) and place on the front of the receiver.
• Repeat for all 8 satellite receivers.
Now connect each receiver output with DIN cables (Stk#3703) to the encoder inputs, making
1
sure that receiver #1 (RX#1) is connected to #1 component input on the encoder. Repeat this
process for remaining receivers.
Connect the 8 satellite receivers and the BBDECA as shown below.
2
• Power up the receivers and the encoder.
Connect the equipment as follows:
PS
Refer to DIRECTV
installation procedures
1
DIN Cables
SWS-8WBMC
RX#8RX#1
BBDECA
2
Control & Monitoring
DT-16PT100M-RM
PC with web browser
CAT5
DECA Power Supply
DC to RF Adapter
Ethernet Port
www.blondertongue.com
Document#651243700A Stock #6371 QIP 2 | #6371 Q 2 | 6371 IP 2
Page 2
STEP 2 - Login
• Log in to the HDE-8C-QAM DIN, using a standard web browser.
• This can be done through the Control 10/100 port, next to the Receiver Control port. Either go
directly from a computer or through an Ethernet switch
• Assign 172.16.70.2 as the static address for your computer
• Now open your browser and enter 172.16.70.1 to access the HDE-8C-QAM DIN.
• The Username is “Admin” and the password is “pass” (case-sensitive)
STEP 3 - Assigning Receivers
Allow several minutes for the receivers to be discovered and assigned IP addresses
From the Main > Input Cong Tab of the Web Pages, assign RX#1 to Input #1, RX#2 to Input #2, etc.
1
TV Zone: For use with BaR Game Changer application. Customize zone names that appear on WiFi
2
remote device.
Program Name: For use with BaR Game Changer application. Field can be left blank and will be
3
automatically populated by BaR app once receivers have been tuned remotely.
4
Click “SAVE” at the bottom to apply changes.
1 2
3
4
Page 3
STEP 4 - TS Configuration
Go to the Main > Output > TS Cong Tab
Verify the Multiplexed MPTS Output default
1
settings are suitable for your application
- TS bitrate = QAM Modulator
- Modulation Mode = QAM 256
- Out of band = disabled
Verify the Output Mapping Section.
2
- Input for each TS must be different.
- Every PID and Program Number must be
different.
- Short Name should be a descriptive
name of the program, as it will be shown
on the television (max 7 alphanumeric
characters)
- Major and Minor Channel numbers are
what the TV will display as the channel.
Click “SAVE” at the bottom to apply changes.
3
1
2
STEP 5 - Configure IP Output*
Go to the Main > Output > IP Tab
Assign the Destination IP, Encapsulation protocol, Destination and Source Ports for each
1
transport stream.
Verify the Stufng is set to “Disabled” and the Output is “Enabled”
2
Click “SAVE” to apply the settings.
3
1
2
NOTE: The IP Output Tab is only available on the HDE-8C-QAM/IP DIN and the HDE-8C-IP DIN models.
3
Page 4
STEP 6 - Configure QAM Output*
Setup the QAM output channels by going to the Main > Output > QAM tab
Select the channel for the 1st QAM. The next 3 will be automatically assigned.
1
Ensure all outputs are on and CW mode is not enabled.
2
Click “SAVE” to apply changes.
3
1
2
3
NOTE: The QAM Output Tab is only available on the HDE-8C-QAM/IP DIN and the HDE-8C-QAM DIN models.
Please visit our website at www.blondertongue.com to download the latest HDE-8C DIN Series Instruction
Manual (PDF document). First time website visitors are required to complete a short registration process
prior to accessing product information.
Once signed in, you can quickly navigate to the product page using search by entering the HDE-8C DIN
model name. The Instruction Manual can be found under the “Documents” tab of each product page.
CONTACT BT FOR MORE INFO | TECH SERVICES: 732-679-4000 x 4358
Loading...