Blodgett SC-10E User Manual

Project

Item No.

Quantity

 Model SC-7E (7 pan electric convection steamer)
 Model SC-10E (10 pan electric convection steamer)

EXTERIOR CONSTRUCTION

 304 satin finish stainless steel
 Welded stainless steel door with removable inner stainless steel liner
 Full perimeter door gasket
 Positive lock and seam mechanism with spring release on door
 Stainless steel control housing

INTERIOR CONSTRUCTION

 One piece welded 316 stainless steel cooking chamber
 Coved corners
 Stainless steel pan supports
 Stainless steel drip trough integrally connected to drain

OPERATION

 Pressureless steam operation
 Delime mode power setting
 Automatic generator blowdown
 Separate controls for each compartment
 Full access removable control panel
 Illuminated on/off/delime power switch
 Ready indicator light
 Cooking indicator light
 60 minute electric timer with audible alarm to signal end of cook cycle
 Solid state generator controls
 Steam flow to the cooking chamber is cut off when the door is opened

during the cooking cycle and reactivated when the door is closed

STANDARD FEATURES

 Deliming port located in the rear of the unit for each generator
 Deliming mode power setting
 Electromechanical controlsl
 Split water connections
 24” wide cabinet base with hinged door and 6” (152 mm) legs
 Standard voltage options

 208 VAC, 3 phase, 60 hz

 240 VAC, 3 phase, 60 hz
 One year parts and labor steamer warranty*
 Five year limited steamer door warranty*

* For all international markets, contact your local distributor.

BLODGETT OVEN COMPANY

www.blodgett.com

44 Lakeside Avenue, Burlington, VT 05401 • Phone: [phone] • Fax: [phone]

OPTIONS AND ACCESSORIES

(AT ADDITIONAL CHARGE)

 Voltage options

 220 VAC, 3 phase, 60 hz
 240 VAC, 3 phase, 60 hz
 220/380, 3 phase, 60 hz, 4 wire
 240/415, 3 phase, 60 hz, 4 wire
 380 VAC, 3 phase 60 hz
 415 VAC, 3 phase, 60 hz
 480 VAC, 3 phase, 60 hz

 600 VAC, 3 phase, 60 hz
 12” x 20” (305 x 508 mm) pan guides for cabinet base
 120 minute timer
 Correctional package
 One year extended warranty

SC-E

Electric Convection Steamer

on a 24” Modular Cabinet Base

SC-E CONVECTION STEAMER

Model

Pan Depth

1” 2.5” 4” 6”

SC-7E 14 7 4 2
SC-10E 20 10 6 4

CAPACITY

 Model SC-7E is comprised of one 3 pan steamer com-

partment and one 4 pan steamer compartment

 Model SC-10E is comprised of two 5 pan steamer com-

partments

SC-7E shown

BLODGETT OVEN COMPANY

www.blodgett.com 44 Lakeside Avenue, Burlington, VT 05401 • Phone: [phone] • Fax: [phone]

SC-E CONVECTION STEAMER

SHORT FORM SPECIFICATIONS

Provide Blodgett model SC-7E (7 pan), SC-10E (10 pan) convection steamer with electric steam generator mounted on a 24” wide cabinet base. The SC-7E is comprised of one 3 pan
compartment on top of one 4 pan compartment. The SC-10E is comprised of two 5 pan compartments. Each compartment shall have it’s own steam generator. Unit shall be constructed
of satin finish 304 stainless steel with a one piece 316 welded stainless steel cooking chamber with coved corners. The door shall have a removable inner liner of stainless steel with full
perimeter gasket seal, an outer liner of one-piece all welded stainless steel, and a positive lock and seal mechanism with spring release. Each compartment shall have removable stain­less steel pan supports and a stainless steel drip trough integrally connected to collect and drain condensate with the doors are open. The control housing shall be constructed of stain­less steel with a full access removable panel. The controls shall include an illuminated on/off/delime power switch, a ready indicator light, cooking indicator light, 60 minute electric timer
with audible alarm that signals the end of the cook cycle, solid state generator controls and delime mode power setting. Steam flow to the compartment shall be cut off when the door is
opened during the cook cycle and shall be reactivated when the door is closed. Unit shall have a deliming port located in the rear. The unit shall have an automatic generator blow down
and split water connections. Provide options and accessories as indicated.

WATER SUPPLY:

Water quality is a major factor affecting the performance of your steamer. If you are unsure
of water quality, consult a local water treatment specialist and have the water analyzed.
Your water supply must be within these general guidelines:

Total dissolved solids: Less than 60 PPM Total alkalinity: Less than 20 PPM
Silica: Less than 13 PPM Chlorine: Less than 1.5 PPM
pH Factor: 7.0 - 8.5
Water which fails to meet these standards should be treated by installation of a water
conditioner. Failure or malfunction of this steamer due to poor water quality is not covered

under warranty.

WATER & DRAIN CONNECTIONS:

Drain 1” (25mm) IPS piped to open floor drain. No solid connection.

24” length before open air gap opening (no bends or elbows)
Cold Water 3/8” (10mm) tubing at 25-50 PSI (170-345 kPa)
Appliance is to be installed with backflow protection in accordance with Federal, State or

Local codes.

MAXIMUM INPUT:

SC-7E 17.5 kW
SC-10E 24kW standard, 30 kW (optional)

POWER CONNECTION:

1-1/8” (29mm) hole for electrical connection

SHIPPING INFORMATION:

Approx. Weight:

SC-7E 400 lbs. (181 kg)
SC-10E 450 lbs. (204 kg)

Printed in U.S.A. NOTE: FOR COMMERCIAL USE ONLY

NOTE: The company reserves the right to make substitutions of components without prior
notice.

9 [229]

16.75 [425]

33 [838]

1.38 [35]

24 [610]

1.12 [29]

27.38 [695]

1/2-NPT DELIME INLET

27.69 [703]

2.19 [56]

3.94 [100]

3 [76]

1.75 [45]

28 [711]

6 [152]

1.5 [38]

1 [25]

5 [127]

2.62 [67]

16.62 [422]

63.75 [1619] SC-7E

73.5 [1867] SC-10E

SC-7E

SC-10E

19.88 [505]

19.5 [495]

2.19 [56]2.19 [56]

REAR FLANGED FOOT DETAIL

7/16" [11mm] HOLES

ON 2.5 [63] B.C.

2 EQUALLY SPACED
Ø

APPROVAL/STAMP

P/N S00010 Rev J (8/11)

AMPS PER LINE

kW Phase 208V 220V 240V 380V 480V

17.5 3 48.6 45.9 42.1 26.6 21.1

24 3 66.6 63 57.8 36.5 28.9

30 3 83.3 78.7 72.2 45.6 36.1