RP4-CH11
Pacific Accessory Corporation
SWC Connection
See above chart for
different radio type
connections
x4
Radio Replacement & Steering Wheel Control Interface
for Chrysler/Dodge/Jeep Vehicles
Introduction & Features
The RP4-CH11 interface allows the replacement of a factory radio in select Chrysler/Dodge/Jeep vehicles with MSCAN or
LSFT-CAN databus radios. Using this interface will retain factory features such as steering wheel controls (SWC) vehicle
entertainment system (VES) and the factory audio amplier whenever the original radio is removed. The RP4-CH11 also
provides data bus driven outputs such as retained accessory power (RAP), vehicle speed sensor (VSS), illumination,
reverse trigger and parking brake.
Important Notes
1. The radio select rotary switch on the side of the interface must be adjusted to the proper radio setting before plugging the
interface into the vehicle (see next page for setting chart).
2. When the interface is rst plugged into the vehicle the LED will ash indicating the auto detect sequence. Once the CAN-BUS
speed is detected the LED will illuminate and should be on at all times when the interface is on. The LED will also ash whenever
a SWC button is pressed
3. The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming unless
you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by pressing
and releasing the program button on the side of the interface once and waiting 7 seconds for the LED to ash 4 times.
Wiring Connection Chart
Interface Connector
Red / White P.B. Output (-)
Purple / White VSS Output
Blue / White Amp Turn On Input
Red Acc. Output (1 amp)
Orange / White Illum. Output (+)
Green Reverse Output (+)
Illustration / Schematic
Wiring SWC Connection
White / Black Front L - input
Grey / Black Front R - input
Green / Black Rear L - input
Purple / Black Rear R - input
Interface Connector
See above chart for
wire color descriptions.
Vehicle Connector
Yellow Battery +12v
Black Ground
Blue Antenna On Input
White Front L + input
Grey Front R + input
Green Rear L + input
Purple Rear R + input
SWC Connector
Blu/Yel Kenwwod, Newer
JVC, OEM or
Blaupunkt
3.5mm Jack Alpine, JVC,
Clarion, Pioneer,
Sony, Valor, Boyo,
Dual, Visteon or
Advent
Vehicle Connector
See above chart for
wire color description.
Accessory Output
+12volts 1amp max.
1
Pacic Accessory Corporation® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
9
©2011 Pacic Accessory Corporation
www.pac-audio.com
Rev. 112811
Page 1
RP4-CH11
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
0
V
r
V
V
V
A
r
r
Radio Replacement & Steering Wheel Control Interface
for Chrysler/Dodge/Jeep Vehicles
Installation Steps
SET RADIO SELECT SWITCH
Advent,
Alpine
1 7 8 4 2 3 6 7 5
1.The radio select rotary switch on the side of the interface must be adjusted to the proper radio
setting before plugging the interface into the vehicle (see page 2 for setting chart).
2. Only one of the two provided radio harnesses will be used. Remove the factory installed radio to determine the correct harness for your
particular vehicle.
3. Make all connections as described in the connection chart on page 1. Vehicles without a factory amplier: Connect the aftermarket radio’s
front and rear speaker wires to the vehicle connector. Vehicles with a factory amplier: The factory amplier only accepts two channels
of audio input (left and right). Connect the front outputs of the aftermarket radio to the rear inputs of the vehicle connector. This will allow
navigation voice prompts and Bluetooth calls to be heard. The rear speaker outputs of the aftermarket radio are not used. Fading is not
supported in this application. The factory amplier’s fading is controlled by data communication from the factory radio. Neither the aftermarket
radio or the RP interface have the ability to control the amplier’s fader.
4. Connect the SWC wire according to the chart on page 1 (aftermarket radio MUST support a wired remote input)
5. If you wish to reassign functions to the SWC follow the programming instructions in the next section.
BOYO, Dual,
Visteon, Sony
Blaupunkt Clarion JVC Kenwood OEM Pioneer Valor
Optional Steering Wheel Control Programming
IMPORTANT! The interface comes pre-programmed for all of the vehicles factory SWC functions and does not require programming
unless you wish to re-assign the SWC functions to different buttons. The SWC can always be restored to default settings by
pressing the program button on the side of the interface once and waiting for the timeout.
Default SWC Button Assignments
Alpine JVC Kenwood Clarion
olume + Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
olume - Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume -
Source Source Source Source Source Source Source Source Source
Track + Track + Track + Track + Search + Track + Next Track + Track +
Track - Track - Track - Track - Search - Track - Previous Track - Track -
Preset + Preset + Preset Disc/Radio + Band Mute Band Preset + Disc +
oice Mute Mute Mute Mute Cursor - Answer Mute Mute
Phone Receive Receive
nswe
Send/End Cursor + Hang UpAnswe
If you wish to re-assign the SWC functions, the interface must be programmed in the specic order shown in the chart on the next
page. If you come across a function in the chart that your steering wheel does not have, or you do not want to program, press and
release the program button on the side of the interface to skip that function. The LED will ash off and on conrming that you have
successfully skipped that function and are ready to proceed to the next one.
SET RADIO SELECT SWITCH
SET RADIO SELECT SWITCH
Advent,
Alpine
BOYO, Dual,
Blaupunkt Clarion JVC Kenwood OEM Pioneer Valor
Visteon, Sony
1 7 8 4 2 3 6 7 5
alo
OEM Sony/PioneerBlaupunkt
OK
Pacic Accessory Corporation® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2011 Pacic Accessory Corporation
www.pac-audio.com
Rev. 112811
Page 2
11/9/2011 - 11:01 AM swi-rc radio and button chart.xls
Alpine JVC Kenwood Clarion Valor OEM
A
dvent, Boyo, Dual,
Visteon, Sony
Pioneer Blaupunkt
1 Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume + Volume +
2 Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume - Volume 3 Mute Mute Mute Mute Mute Mute Mute Mute Mute
4 Preset + Source Source Source Source Source Preset + Preset + Source
5 Preset - Track + Play Search + Track + Next Preset - Preset - Track +
6 Source Track - Track + Search - Track - Previous Source Source Track 7 Track + Band/Disc + Track - Band Up Cursor Play/Ok Track + Track + Disc +
8 Track - Preset/Disc - Disc/FM + Send/End Down Cursor Band Track - Track - Disc -
9 Power Select Disc/AM - Send Ok Up Cursor Band Band Ok
10 Enter/Play Attenuation Answer End Down Cursor Phone Menu
11 Band/Program Phone Receive BT Answer Answer Call
12 Receive Phone Reject BT Hangup End Call
13 End Voice Dial Voice Activation
14 Powe
r
Optional Steering Wheel Control Programming (cont.)
x4
Optional Programming Order
RP4-CH11
Radio Replacement & Steering Wheel Control Interface
for Chrysler/Dodge/Jeep Vehicles
Step A.
Turn the vehicle ignition to
the ON position.
Step C.
Release the
programming
button. The
LED will turn
back on.
IGN
ACC
STRT
OFF
Step D.
Within 7 seconds,
press and release the
button that is to be
learned on the steering
wheel.
Step B.
Press and
hold the
programming
button.
VOL
Step E.
Release the button.
VOL
Step F.
If you need to program more buttons,
repeat steps D & E for each additional
audio function on the steering wheel.
remaining buttons
Program
LED will turn off.
The LED will
turn off during
this process.
The LED will turn on
back on.
Step G.
After all buttons are
programmed
Pacic Accessory Corporation® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
Once programming is
completed,
The LED will ash four
times indicating the end of
programming.
©2011 Pacic Accessory Corporation
www.pac-audio.com
wait 7 seconds.
Rev. 112811
Page 3
RP4-CH11
Radio Replacement & Steering Wheel Control Interface
for Chrysler/Dodge/Jeep Vehicles
Testing & Verication
1. Turn the ignition on. The LED on the interface will turn on & the +12v accessory wire will turn on.
2. Turn on the radio & check balance & fade. Note: Factory amplied Systems will not fade as neither the aftermarket radio or
the RP interface have the ability to control the amplier’s fader.
3. Verify that the factory subwoofer (if present) is playing
4. Verify that all SWC are functioning properly.
4. Turn off vehicle & remove key. RAP will be active & keep the radio on for 10 minutes or until the drivers door is opened.
5. The LED & radio will turn off when RAP turns off or the drivers door is opened.
Vehicle Entertainment System (VES); If equipped
1. Vehicles equipped with a DVD player built into the rear screen assembly:
The RP4-CH11 will allow the VES DVD player and rear screen to function as if the factory radio were present. A/V will be passed
from the factory DVD player to the rear screen and audio can be heard through the headphones. A/V cannot be passed from the
factory DVD player to the aftermarket head unit.
2. Vehicles equipped with a stand alone VES DVD Player:
The RP4-CH11 will allow the VES DVD player and rear screen(s) to function as if the factory radio were present. A/V will be
passed from the factory DVD player to the rear screen(s) and audio can be heard through the headphones. A/V can also be fed
from the VES DVD player into an aftermarket head unit (head unit must support A/V in) with the use of the CHYRVD. It is VERY
IMPORTANT that the RP4-CH11 Blue/White remote input wire be connected for this feature to function properly!
3. Vehicles not equipped with a VES DVD Player (rear screen(s) only):
In this application the CHYRVD must be used in order to feed A/V into the factory screen(s) from an aftermarket head unit (head
unit must support A/V out). With the CHYRVD, A/V will be passed from the aftermarket head unit to the rear screen(s) and audio
can be heard through the headphones. If you wish to retain the Auxiliary inputs on the rear of the console you must disconnect
the factory wires from the auxiliary input then connect and run your own RCAs into the aftermarket head unit.
4. Vehicles equipped with a Reverse Camera:
In order to retain the factory reverse camera the CHYRVD must be used to feed video into the aftermarket head unit (head unit
must support reverse camera input).
Product Updates (Firmware)
The RP4-CH11 can be updated with new rmware as it becomes available using the PAC-UP interface updater (sold seperatly).
Please visit www.pac-audio.com/rmware for available updates.
Pacic Accessory Corporation® | Santa Ana, California 92705 | Ph. 866-931-8021 | support@pac-audio.com
©2011 Pacic Accessory Corporation
www.pac-audio.com
Rev. 112811
Page 4
Loading...