REVERSE CAMERA
RC 1.0
RC 2.0
RC 3.0
Operating and Installation Instructions
Enjoy it.
CAUTIONS
Safety Notes
This vehicle security system has been manufactured according to established safety
guidelines. However, dangers may still occur
if the safety notes in this manual is not observed. This manual is intended to familiarize
the user with the reverse camera important
functions. Read this carefully, prior to using
the reverse camera. Keep this manual in an
easily accessible location. In addition, do
observe the instructions of the devices used
in conjunction with this reverse camera.
Attentions
•
Assign a mounting location that will not
obstruct driver in any circumstances. Or
cause injuries to drives and passengers in
case of emergency brake or accidents.
•
Ensure all wires are connected properly,
and that the unit is functioning well before
tting the unit into the mount.
•
Any unauthorized installation, disassembly
or modication may cause malfunction to
the unit and void warranty of the unit.
•
Always use only the parts that are included with the units only.
•
Do not damage vehicle components when
drilling holes for the mount.
•
Vehicle may dier from the description
provided here. Consult an authorized
Blaupunkt dealer or vehicle’s manufacturer
if the information provided here does not
t your specic installation requirement.
•
This unit is applicable for front and reverse
camera use. Consult an authorized
Blaupunkt dealer during installation.
•
Unit does not record video.
•
Avoid automatic car wash or high-pressure
water to prevent water and pressure
from damaging the camera or causing
it to fall o.
•
Do not install this unit near heater outlet.
This manual may be updated from time to
time without any notice.
Disclaimer
In no event shall Blaupunkt be liable for any
direct, indirect, punitive, incidental, special
consequential damages to property or life
and whatsoever arising out of or connected
with the use or misuse of our products.
USA & CANADA: This product is not intended
for sale in the United States and Canada. If
purchased in the U.S. or Canada, this product
is purchased on as-is basis. No warranty,
whether expressed or implied is provided in
the U.S. or Canada.
1
SPECIFICATIONS
Features
CMOS Image Sensor
NTSC/PAL TV System
Eective Pixels
750TVL Image Resolution
25/30 Frame Per Second
Exposure & Gain Control
1/60~1/100000sec
Electronic Shutter
Auto White Balance
Illumination Min.
Horizontal View
Vertical View
Diagonal View
DC12V Voltage
Current
DC9-16V Operating
Voltage Range
Operating Temperature
Storage Temperature
Protection Grade
RCA/4 PIN DIN
Lens
RC1.0
720 (H) x 480 (V)
0.2 Lux/F
105°H
95°V
170°D
29.3mA
-20~+70 °C
-30~+75°C
IP68
4glass
2
RC2.0
720 (H) x 480 (V)
0.2 Lux/F
145°H
125°V
170°D
27.1mA
-20~+70 °C
-30~+75°C
IP68
4glass
RC3.0
1280 (H) x 720 (V)
0.1 Lux/F
160°H
140°V
170°D
61.5mA
-20~+70 °C
-30~+75°C
IP68
5glass
INSTALLATION DIAGRAM
Display Monitor/
Car Radio
Black Wire (Ground)
Red Wire
P
R
N
D
L
2
Reverse Light
Ground the wire through the exterior body of the vehicle and keep connection intact.
Reverse Camera
Attention
Remove protective lm from camera lens before use.
•
Take extra precautions when setting up the connection near petrol tank
•
and wires.
Connect Red Wire with reverse light.
•
Display Monitor/Car Radio
2
Reverse
Camera
FRONT / REAR CAMERA INSTALLATION
FRONT/ REAR VIEW DISPLAY & PARKING LINE
Applicable for RC 1.0, RC 2.0
Monitor
GND Rear Power
Camera
Video
White
Blue
Reverse Camera
Do not cut this wire when using
as reverse camera.
Reverse Camera
Do not cut this wire when using
as reverse camera.
Applicable for RC 3.0
Monitor
GND Rear Power
For Reverse Camera
Camera
Video
Front Camera
Cut this wire when using as front
camera to ip viewing display.
Front Camera
Cut this wire when using as front
camera to remove parking line.
Front Camera
Reconnect this wire when using as
front camera to ip viewing display
and remove parking line.
4
White
INSTALLATION LOCATION
Tail
Light
TYPE 1
Remove one side of
1 2
the reverse light
socket from its
housing then remove
the bulb from its
socket.
Connect the reverse
light power cable to
the camera, screwn
the housing & camera
back into position
with a screwdriver.
Hatch
Use a screwdriver
1
to remove the original
hatch handle
Mount the camera
2
where the original
hatch handle used
to be
Handle
TYPE 2TYPE 3
Remove the rotating
1
mount before installation. Drill an access
hole for the
Car
camera cables
Plate
Adjust
Viewing
After
Angle
Installation
Remarks :
1. Pictures are for illustration purpose only, see actual vehicle for accurate installation location.
2. Ensure diameter of hole size is correct before drilling.
3. Ensure drilling process does not harm the component of the vehicle.
4. Assign mounting location that will not obstruct camera view.
5
Mount the camera
2
onto the acces hole
& secure it in position
with 3M tape/ screws
TROUBLESHOOTING
If any of the following problem occur, please resort to Troubleshooting for the possible
solutions. Consult Blaupunkt authorized dealer if problem persist.
Problem
Display monitor / car radio does not
show reverse view when reversing.
Reverse view does not show even
after restarting the display monitor/
car radio.
Reverse view does not show even
though power supplies of the reverse
light or the rear car plate light is
properly connected.
Solution
Restart the display monitor / car radio.
Examine if the power supplies of the reverse
light or the rear car plate light is properly
connected.
Examine if the power supply cables of the
reverse light or the rear car plate light is
damaged. Repair/replace if the cables are
damaged.
6
Designed and engineered by Blaupunkt Competence Centre
RC 1.0
1 331 19 003 32 02
RC 2.0
1 331 19 004 32 02
RC 3.0
1 331 19 005 32 02
Loading...