Black & Decker Pw1300td Instruction Manual [ar]

PW1300TD

www.blackanddecker.ae

PW1300TDW

PW1300TD

PW1300TDW

ENGLISH

A1-A2-A3-A4

PW1300TDW

ENGLISH

Ø13

PW1300TDW

ENGLISH

25 ÷ 50 m

2 x 2,5 mm

1 ÷ 25 m

S = Switch Z1 = Capacitor suppressor T = Thermal protection M = Motor S1 = Pressure switch

Volt

230 2 x 1,5 mm

NCNOC

ENGLISH

Safety instructions

The appliance you have purchased is a technologically advanced product designed by one of the leading European manufacturers of high pressure pumps. To obtain the best performance from your unit, read this booklet carefully and follow the instructions each time you use it. We congratulate you on your choice and wish you successful operation.

Safety rules/residual risks

Safety “must nots”

• Do not use the appliance with inﬂammable or toxic liquids, or any products which are

not compatible with the correct operation of the

appliance. Explosion or poisoning hazard

• Do not direct the water jet towards people or animals. Injury hazard

• Do not direct the water jet towards the unit

itself, electrical parts or towards other electrical

equipment. Electric shock hazard

• Do not use the appliance outdoors in case of rain. Short circuit hazard

• Do not allow children or incompetent persons to use the appliance. Injury hazard

• Do not touch the plug and/or socket with wet hands. Electric shock hazard

• Do not use the appliance if the electrical

cable is damaged. Electric shock and short circuit

hazard

• Do not use the appliance if the high pressure hose is damaged. Explosion hazard

• Do not jam the trigger in the operating position. Accident hazard

• Check that the data plates are afﬁxed to the

appliance, if not, inform your dealer. Units without plates

must not be used as they are unidentiﬁable and potentially dangerous. Accident hazard

• Do not tamper with or adjust the setting of the safety valve or the safety devices. Explosion hazard

• Do not alter the original diameter of the spray head nozzle. Hazardous alteration of operating performance

• Do not leave the appliance unattended. Accident hazard

• Do not move the appliance by pulling on the electrical cable. Short circuit hazard

• Make sure that cars do not drive over the high pressure

hose.

• Do not move the appliance by pulling on the high

pressure hose.

Explosion hazard

• When directed towards tyres, tyre valves or other pressurised components, the high pressure jet is potentially dangerous. Do not use the rotating nozzle kit, and always keep the jet at a distance of at least 30 cm during cleaning. Explosion hazard

Safety “musts”

• All electrical conductors must be protected against the water jet. Short circuit hazard

• The appliance MUST ONLY BE CONNECTED to an adequate power supply in compliance with all applicable regulations. Electric shock hazard

• Use of a safety residual current circuit-breaker (R.C.C.B.) will provide additional protection for the operator (30 mA). Models supplied without plug must be installed by qualiﬁed staff. Use only authorized electrical extension leads with suitable conductor gauge.

•

High pressure may cause parts to rebound: wear all the

protective clothing and equipment needed to ensure the operator’s safety. Injury hazard

• Before doing work on the appliance, remov e the plug. Accidental start-up hazard

• Before pressing the trigger, grip the gun ﬁrmly to counteract the recoil. Injury hazard

• Comply with the requirements of the local water supply company. According to EN 12729 (BA), the

appliance may only be connected to the mains drinking

water supply if a backﬂow preventer valve with drain facility is installed in the supply hose. Contamination hazard

ENGLISH

• Maintenance and/or repair of electrical components must be carried out by qualiﬁed staff. Accident hazard

• DISCHARGE residual pressure before disconnecting the unit hose. Injury hazard

• Before using the appliance, CHECK every time that the screws are fully tightened and that there are no broken or worn parts. Accident hazard

• Only use detergents which will not corrode the coating materials of the high pressure hose/electrical cable. Explosion and electric shock hazard

• Ensure that all people or animals keep a minimum distance of 16 yd. (15m) away. Injury hazard

General information (ﬁg.1)

Use of the manual

This manual forms an integral part of the appliance and should be kept for future reference. Please read it carefully before installing/ using the unit. If the appliance is sold, the Seller must pass on this manual to the new owner along with the appliance.

Delivery

The appliance is delivered partially assembled in a cardboard box. The supply package is illustrated in ﬁg.1.

Documentation supplied with the appliance

• A1 Use and maintenance manual

• A2 Safety instructions

• A3 Declaration of conformity

• A4 Warranty regulations

Disposing of packaging

The packaging materials are not environmental pollutants but must still be recycled or disposed of in compliance with the relevant legislation in the country of use.

Safety signs

Comply with the instructions provided by the safety signs ﬁtted to the appliance.

Check that they are present and legible; otherwise, ﬁt replacements in the original positions.

E1 sign – Indicates that the appliance must not be disposed of as municipal waste; it may be handed in to the dealer on purchase of a new appliance. The appliance's electrical and electronic parts must not be reused for improper uses since they contain substances which constitute health hazards.

Symbols

E2 symbol – Indicates that the appliance is intended for professional use, i.e. for experienced people informed about the relative technical, regulatory and legislative aspects and capable of performing the operations necessary for the use and maintenance of the appliance.

E3 symbol – Indicates that the appliance is intended for non-professional (domestic) use.

Technical information (ﬁg.1)

Envisaged use

This appliance has been designed for individual use for the cleaning of vehicles, machines, boats, masonry, etc, to remove stubborn dirt using clean water and biodegradable chemical detergents. Vehicle engines may be washed only if the dirty water is disposed of as per regulations in force.

• Intake water temperature: see data plate on the appliance.

• Intake water pressure: min. 0,1MPa-max 1MPa.

• Operating ambient temperature: above 0°C.

• The appliance is compliant with the EN 60335-2-79/A1 standard.

Operator

The symbol on the front cover identiﬁes the appliance’s intended operator (professional or non-professional).

Improper use

• Use by unskilled persons or those who have not read and understood the instructions in the manual is forbidden.

• The introduction of inﬂammable, explosive and toxic liquids into the appliance is prohibited.

• Use of the appliance in a potentially inﬂammable or explosive atmosphere is forbidden.

• The use of non-original spare parts and any other spare parts not speciﬁcally intended for the model in question is prohibited.

ENGLISH

• All modiﬁcations to the appliance are prohibited. Any modiﬁcations made to the appliance shall render the Declaration of Conformity null and void and relieve the manufacturer of all liability under civil and criminal law.

Main components

• B1 Adjustable spray nozzle

• B2 Lance

• B3 Gun with safety catch

• B4 Power supply cable with plug

• B5 High pressure hose

• B6 Detergent tank (on models with this feature)

Accessories (if included in the supply package –

see ﬁg.1)

• C1 Nozzle cleaning tool

• C2 Rotating nozzle kit

• C3 Handle

• C4 Brush

• C5 Hose reel

Safety devices

Caution - Danger!

Do not tamper with or adjust the safety valve setting.

• Safety valve and/or pressure limiting valve. The safety valve is also a pressure limiting valve. When the gun trigger is released, the valve opens and the water recirculates through the pump inlet or is discharged onto the ground.

• Thermostat valve (D1 where ﬁtted). If the water temperature exceeds the temperature set by the manufacturer, the thermostat valve discharges the hot water and draws in an amount of cold water equal to the amount of water discharged, until the correct temperature is restored.

• Safety catch (D): prevents accidental spraying of water.

Installation (ﬁg.2)

Assembly

Caution - Danger!

All installation and assembly operations must be

performed with the appliance disconnected from the mains power supply.

The assembly sequence is illustrated in ﬁg.2.

Assembling the rotating nozzle

(For models with this feature)

The rotating nozzle kit delivers greater washing power. Use of the rotating nozzle may cause of reduction in pressure of 25% compared to the pressure obtained with the adjustable nozzle. However, the rotating nozzle kit delivers greater washing power due to the rotation of the water jet.

Electrical connection

Caution - Danger!

Check that the electrical supply voltage and frequency (V-Hz) correspond to those speciﬁed on the appliance data plate (ﬁg.2). The appliance should only be connected to a mains power supply equipped with an adequate earth connection and a differential security breaker (30 mA) to cut off the electricity supply in the instance of a short circuit.

Use of extension cables

Use cables featuring “IPX5” protection level. The cross-section of the extension cable should be proportionate to its length; the longer it is, the greater its cross-section should be. See table I.

Water supply connection

Caution - Danger!

Only clean or ﬁltered water should be used for intake. The delivery of the water intake tap should be equal to that of pump capacity.

Place the appliance as close to the water supply system as possible.

Connection points

• Water outlet (OUTLET)

• Water inlet with ﬁlter (INLET)

Connection to the mains water supply

The appliance can be connected directly to the mains drinking water supply only if the supply hose is ﬁtted with a backﬂow preventer valve as per current regulations in force. Make sure that the hose is at least Ø 13 mm and that it is reinforced.

ENGLISH

Adjustment information (ﬁg.3)

Adjusting the spray nozzle

(for models with this feature)

• Water ﬂow is adjusted by regulating the nozzle (E).

Adjusting the detergent

(on models with this feature)

• Detergent ﬂow is adjusted using the regulator (F).

Adjusting the detergent pressure

Set the adjustable nozzle (E) on " - " to deliver detergent at the correct pressure (on models with this feature).

Adjusting the pressure

(on models with this feature)

• The regulator (G) is used to adjust the working pressure. The pressure is shown on the pressure gauge (where ﬁtted).

Information on use of the appliance (ﬁg.4)

Controls

• Starter device (H).

Set the starter switch on (ON/1) to:

a) Start the motor (in models without TSS device);

b) Set the motor ready to start (in models with TSS

device).

• If there is a pilot light on the starter device, it should light up.

• If the “low/high” settings are available, use them as follows:

• Low : low pressure washing

• High : high pressure washing

• Set the starter device switch on (OFF/0) to shut down the appliance.

• If there is a pilot light on the starter device, it should go out.

• Water jet control lever (I).

Caution - Danger!

During operation the appliance must be positioned as shown in ﬁg. 4 on a sturdy, stable surface.

Start-up

1) Turn on the water supply tap fully.

2) Release the safety catch (D).

3) Depress the gun trigger for a few seconds and start up the appliance using the starter device (ON/1).

Caution - Danger!

Before starting up the appliance check that the water supply hose is connected properly; use of the appliance without water will damage it; do not cover the ventilation grilles when the appliance is in use.

TSS models - In TSS models with automatic delivery ﬂow cut-off system:

• When the gun trigger is released the dynamic pressure automatically cuts out the motor (see ﬁg.4);

• When the gun trigger is depressed the automatic drop in pressure starts the motor and the pressure is restored after a very slight delay;

• If the TSS is to function correctly all gun releasing and depressing operations must be performed at intervals of less than 4-5 seconds.

• On three-phase models for professional use, at ﬁrst use start the appliance for a very short time to check that the motor is running in the correct direction. If the motor fan is turning anti-clockwise, exchange two of the three phase wires (L1, L2, L3) in the electrical plug.

• To prevent damage to the appliance, do not allow it to operate dry and when running do not stop the water jet for more than 10 minutes at a time (for models without TSS device).

Stopping the appliance

1) Set the starter device switch on (OFF/0).

2) Depress the gun trigger and discharge the residual pressure inside the hoses.

3) Engage the gun safety catch (D).

Restarting

1) Release the safety catch (D).

2) Depress the gun trigger and discharge the residual air inside the hoses.

3) Set the starter device on (ON/1).

ENGLISH

Storage

1) Switch the appliance off (OFF/0).

2) Remove the plug from the socket.

3) Turn off the water supply tap.

4) Discharge the residual pressure from the gun until all the water has come out of the nozzle.

5) Drain and wash out the detergent tank at the end of the working session. To wash out the tank, use clean water instead of the detergent.

6) Engage the gun safety catch (D).

Reﬁlling and using detergent

When using detergent, the adjustable nozzle must be set on "-" (on models with this feature).

Use of a high pressure hose longer than the one originally supplied with the cleaner, or the use of an additional hose extension, may reduce or completely halt the intake of detergent.

Fill the tank with highly degradable detergent.

Recommended cleaning procedure

Dissolve dirt by applying the detergent mixed with water to the surface while still dry.

When dealing with vertical surfaces work from the bottom upwards.

Leave the detergent to act for 1-2 minutes but do not allow the surface to dry. Starting from the bottom, use the high pressure jet at a minimum distance of 30 cm. Do not allow the rinse water to run onto unwashed surfaces.

In some cases, scrubbing with brushes is needed to remove dirt.

High pressure is not always the best solution for good washing results, since it may damage some surfaces. The

ﬁnest adjustable nozzle jet setting or the rotating nozzle

should not be used on delicate or painted parts, or on

pressurised components (e.g tyres, inﬂation valves, etc.).

Effective washing depends on both the pressure and volume of the water used, to the same degree.

Maintenance (ﬁg.5)

Any maintenance operations not covered by this chapter should be carried out by an Authorized Sales and Service Centre.

Caution - Danger!

Always disconnect the plug from the power socket before carrying out any work on the appliance.

Cleaning the nozzle

1) Disconnect the lance from the nozzle.

2) Remove any dirt deposits from the nozzle hole using the tool (C1).

Cleaning the ﬁlter

Inspect the intake ﬁlter (L) and detergent ﬁlter (if ﬁtted)

before each use, and clean in accordance with the instructions if necessary.

Unjamming the motor (on models with this feature)

In case of lengthy stoppages, limescale sediments may cause the motor to seize. To unjam the motor, turn the drive shaft with a tool (M).

End-of-season storage

Treat the appliance with non-corrosive, non-toxic antifreeze before storing it away for winter.

Put the appliance in a dry place, protected from frost.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be ﬁtted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in the new

plug.

• Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.

Follow the ﬁtting instructions supplied with good quality plugs. Recommended fuse: 5 A.

ENGLISH

Troubleshooting

Problem Possible causes Remedy

Nozzle worn Replace nozzle

Water ﬁlter fouled Clean ﬁlter (ﬁg.5) Water supply pressure low Turn on water supply tap fully Air being sucked into system Check tightness of hose ﬁttings Pump does not reach Air in pump Switch off the appliance and keep depressing and

working pressure releasing the gun trigger until the water comes out in a steady ﬂow. Switch the appliance back on again.

Adjustable nozzle not Turn the adjustable positioned correctly nozzle (E) (+) (ﬁg.3)

Thermostatic valve tripped Wait for correct water temperature to be restored Water intake from external tank Connect appliance to the mains water supply Pressure drops during use Intake water too hot Reduce temperature Nozzle clogged Clean nozzle (ﬁg.5) Intake ﬁlter (L) dirty Clean ﬁlter (L) (ﬁg.5) Insufﬁcient power supply Check that the voltage of the mains power

supply line is the same as that on the plate (ﬁg.2)

Voltage loss due to use of Check characteristics of extension cable Motor “sounds” but fails to start extension cable

Appliance not used for a Contact your nearest Authorized Service Centre long period of time

Problems with TSS device Contact your nearest Authorized Service Centre No electrical power Check that the plug is ﬁrmly in the socket

and that the mains voltage supply is present (*) Motor fails to start Problems with TSS device Contact your nearest Authorized Service Centre Appliance not used for a Using the tool (L) unjam the motor

long period of time from the hole at the rear of the appliance (in models with this feature) (ﬁg.5)

Seals worn Have the seals replaced at your nearest Water leakage Authorized Service Centre

Safety valve tripped and discharging Contact an Authorized Service Centre Appliance noisy Water too hot Reduce temperature (see technical data Oil leakage Seals worn Contact your nearest Authorized Service Centre Nozzle clogged Clean nozzle (ﬁg.5)

TSS versions only: motor starts even with gun trigger is released High pressure system or pump Contact your nearest Authorized Service Centre

hydraulic circuit not watertight TSS versions only: no water

delivery when gun trigger is Nozzle clogged Clean nozzle (ﬁg.5) depressed (with supply hose connected)

Adjustable nozzle on high pressure setting Set nozzle on "-" setting (ﬁg.5) Detergent too dense Dilute with water No detergent taken in High pressure hose extension being used Fit original hose Deposits or restriction in detergent circuit Flush with clean water and eliminate any restrictions.

If the problem persists, contact an Authorized Service Centre

(*) If the motor starts and does not restart during operation, wait 2-3 minutes before repeating the start-up procedure (overload cutout has

been tripped). If the problem recurs more than once, contact your nearest Authorized Service Centre.

ENGLISH

Declaration of conformity

We declare under our sole responsibility that this product is in conformity with the following standards or standardized

EN 60335-1 - EN 60335-2-79; EN 55014-1; EN 55014-2;

EN 61000-3-2;EN 61000-3-3; EN 61000-3-11; EN 60704-1

2006/42/CE, 2006/95/CE, 2002/95/CE, 2002/96/CE, 2004/108/CE, 2000/14/CE

or more information, please contact Black & Decker at the following address or refer to the back of the manual. The

undersigned is responsible for compilation of the technical ﬁle and makes this declaration on behalf of Black & Decker.

Kevin Hewitt Vice-President Global Engineering Black & Decker Europe, 210 Bath Road, Slough, Berkshire, SL1 3YD United Kingdom 04/02/2013

In accordance with the regulations:

documents

Technical Data

Unit PW1300TD PW1300TDW Output L/min 6 6 Pressure MPa 7 7 Maximum pressure MPa 10 10 Power kW 1,3 1,3 T° input °C 50 50 Maximum input pressure MPa 1 1 Repulsive force of the gun to the maximum pressure N 9,1 9,1 Motor Insulation - Class F Class F Motor Protection - IPX5 IPX5 Voltage V/Hz 230/50 230/50 Sound level (K=3 dB(A)) : LPA (EN 60704-1) dB (A) 75,1 75,1 LWA (EN 60704-1) dB (A) 83 83 Unit vibrations (K=1.5M/s2) M/s2 2,74 2,74 Weight kg 5,6 5,6

+ 28 hidden pages