Black + Decker JUS500IB, JUS500IBCA Instruction Manual
132
de la batería por el usuario. Comuníquese con el fabricante para cualquier información que pueda
necesitar.
ELIMINACIÓN SEGURA DE LA BATERÍA
Contiene una batería de plomo ácido, que se deben desechar de manera adecuada. Reciclar
es necesario. El incumplimiento de regulaciones locales, estatales y federales, puede
resultar en multas o prisión.
Por favor recicle.
ADVERTENCIAS:
• No deseche la batería en el fuego ya que puede ocasionar una explosión.
• Antes de desechar la batería, proteja las terminales descubiertas con cinta eléctrica para trabajos pesados. De
esta manera previene cortos circuitos (los cortos circuitos pueden ocasionar lesiones e incendios).
• No exponga la batería al fuego o al calor extremo ya que puede explotar.
ACCESORIOS
Accesorios recomendados para uso con esta unidad puede ser disponibles a través del fabricante. Si necesita
ayuda con respecto a los accesorios, por favor póngase en contacto con el fabricante al 1-877-571-2391.
ADVERTENCIA:
El uso de cualquier accesorio no recomendado para el uso con esta unidad podía ser peligroso.
INFORMACIÓN DE SERVICIO
Si usted necesita asesoramiento técnico, reparación, o partes genuinas del fabricante, póngase en contacto con
el fabricante al 1-877-571-2391.
UN AÑO DE GARANTÍA LIMITADA
El fabricante garantiza este producto contra defectos de materiales y mano de obra durante un período de UN
(1) AÑO a partir de la fecha de compra del producto por el comprador usuario final (“Período de Garantía”). Si
hay un defecto y una reclamación válida se recibe dentro del período de garantía, el producto defectuoso puede
ser reemplazado o reparado en el las siguientes maneras: (1) Devuelva el producto al fabricante para reparación
o reemplazo, a opción del fabricante. La prueba de compra puede ser requerida por el fabricante. (2) Devuelva
el producto a la tienda donde el producto fue comprado para un intercambio (siempre y cuando se trate de un
minorista participante). Devoluciones al minorista deben hacerse dentro del plazo de póliza de devoluciones del
minorista para intercambios solamente (por lo general 30 a 90 días después de la fecha de compra). La prueba
de compra puede ser requerida por el minorista. Por favor consulte la póliza de devoluciones del minorista
sobre devoluciones que están fuera del plazo establecido para intercambios.
Esta garantía no se aplica a los accesorios, bombillos, fusibles y baterías; defectos a consecuencias de desgaste
normal; accidentes; daños y perjuicios sufridos durante el envío y manejo, alteraciones, reparaciones o uso no
autorizado, negligencia, abuso, y si no se siguen instrucciones para el cuidado y mantenimiento del producto.
Esta garantía le otorga al comprador usuario final, derechos legales específicos y usted puede tener otros
derechos que varían de estado a estado o de provincia a provincia. Este producto no está diseñado para uso
comercial.
Por favor completar la tarjeta de registro del producto dentro de un plazo de 30 días a partir de la fecha de
compra y remitir a: Baccus Global LLC, One City Centre, 1 North Federal Highway, Suite 200, Boca Raton, FL
33432.
Baccus Global LLC, número de teléfono gratuito: 1-877-571 2391
.
ESPECIFICACIONES
Amperios de impulso: 500 amperios instantáneos de giro
Tipo de batería: Sellada, alta densidad de energía, placas de vidrio absorbente (AGM), plomo-
ácido, recargable, no requiere mantenimiento, 12 voltios de CC
Luz zonal: Diodo emisor de luz (LED)
Salida del puerto del USB: 5Vdc, 500mA
Presión máxima del
aparato para compresor: 120 PSI
SureFit® es una marca registrada propiedad de Baccus Global, LLC.
Importados por Baccus Global LLC, One City Centre, 1 North Federal Highway, Suite 200, Boca Raton, FL 33432
www.Baccusglobal.com 1-877-571-2391
Catalog Number JUS500IB/JUS500IBCA
500 AMP JUMP-STARTER WITH
COMPRESSOR
INSTRUCTION MANUAL
SAVE THIS MANUAL FOR FUTURE REFERENCE.
Cat. # JUS500IB/JUS500IBCA RD040518
Copyright © 2018 Baccus Global LLC
Thank you for choosing Black & Decker!
Go to www.Baccusglobal.com to register your new product.
PLEASE READ BEFORE RETURNING THIS
PRODUCT FOR ANY REASON:
If you have a question or experience a problem with your purchase, go to
HTTP://WWW.BACCUSGLOBAL.COM
for instant answers 24 hours a day.
If you can’t find the answer or do not have access to the internet,
call 1-877-571-2391 from 9 a.m. to 5 p.m. EST, Mon. – Fri. to speak with an agent.
Please have the catalog number available when you call.
BC
JUS500IB_JUS500IBCA_ManualENFRSP_040518.indd 32-1 4/5/2018 10:03:00 AM
2 3
•
Use safety glasses and other safety equipment.
Use safety goggles or safety glasses with side shields,
complying with applicable safety standards and, when needed, a face shield. Also use face or dust mask if
operation is dusty. This applies to all persons in the work area. Also use a hard hat, hearing protection, gloves,
safety shoes and dust collection systems when specified or required. Safety glasses or the like are available at
extra cost at your local dealer.
•
Don’t abuse cord.
Never carry appliance by cord or yank it to disconnect from receptacle. Keep cord from
heat, oil, and sharp edges.
•
Don’t overreach.
Keep proper footing and balance at all times.
•
Disconnect appliances.
Disconnect the appliance from the power supply when not in use, before servicing,
and when changing accessories such as blades and the like.
•
Avoid unintentional starting.
Don’t carry plugged-in appliance with finger on switch. Be sure switch is off
when plugging in.
•
Ground fault circuit interrupter (GFCI)
protection should be provided on the circuits or outlets to be used.
Receptacles are available having built in GFCI protection and may be used for this measure of safety.
•
Use of accessories and attachments.
The use of any accessory or attachment not recommended for use
with this appliance could be hazardous. Note: refer to the accessory section of this manual for further details.
•
Stay alert.
Use common sense. Do not operate tool when you are tired or impaired.
•
Check damaged parts.
Before further use of the tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced
by manufacturer unless otherwise indicated elsewhere in this instruction manual. Have defective switches
replaced by manufacturer. Do not use tool if switch does not turn it on and off.
•
Do not operate
portable electric tools near flammable liquids or in gaseous or explosive atmospheres. Motors
in these tools normally spark, and the sparks might ignite fumes.
•
Outdoor use extension cords.
When tool is used outdoors, use only extension cords intended for use
outdoors and so marked.
•
Extension cords.
Make sure your extension cord is in good condition. When using an extension cord, be sure
to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop
in line voltage resulting in loss of power and overheating. The following table shows the correct size to use
depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller
the gauge number, the heavier the cord.
MINIMUM GAGE FOR CORD SETS
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
(0-7.6m) (7.6-15.2m) (15.2-30.4m) (30.4-45.7m)
240V 0-50 51-100 101-200 201-300
(0-15.2m) (15.2-30.4m) (30.4-60.9m) (60.9-91.4m)
Ampere Rating Extension Cord Length
More Not more
0’-25’ 26’-50’ 51 ’-100 ’ 101’ -150 ’
Than Than American Wire Gage (AWG)
0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended
SPECIFIC SAFETY INSTRUCTIONS FOR JUMP STARTERS
WARNING: BURST HAZARD:
Do not use the unit for charging dry-cell batteries that are commonly used
with home appliances. These batteries may burst and cause injury to persons and damage property. Use the unit
for charging/boosting a LEAD-ACID battery only. It is not intended to supply power to a low-voltage electrical
system other than in a starter-motor application.
WARNING: SHOCK HAZARD:
• If an extension cord is used, make sure that:
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
SAFETY GUIDELINES / DEFINITIONS
DANGER:
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious
injury.
WARNING:
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION:
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate
injury.
CAUTION:
Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided,
may result in property damage.
RISK OF UNSAFE OPERATION.
When using tools or equipment, basic safety precautions should always be
followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or
equipment could result in serious injury and property damage. There are certain applications for which tools
and equipment are designed. Black & Decker strongly recommends that this product NOT be modified and/or
used for any application other than for which it was designed. Read and understand all warnings and operating
instructions before using any tool or equipment.
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
This product or its power cord contains lead, a chemical known to the State of California to cause
cancer and birth defect or other reproductive harm. Wash hands after handling.
GENERAL SAFETY WARNINGS AND INSTRUCTIONS FOR ALL BATTERY
CHARGERS
READ ALL INSTRUCTIONS
WARNING:
Read all instructions before operating product. Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, BURST HAZARD, OR INJURY TO
PERSONS OR PROPERTY:
•
Avoid dangerous environments:
don’t use appliances in damp or wet locations. Don’t use appliances in the
rain.
•
Keep children away.
All visitors should be kept at a distance from work area.
•
Store idle appliances indoors.
When not in use, appliances should be stored indoors in dry, and high or
locked-up place – out of reach of children.
•
Don’t force appliance.
It will do the job better and with less likelihood of a risk of injury at the rate for which
it was designed.
•
Use right appliance.
Do not use the appliance for any job except that for which it is intended.
•
Dress properly
. Do not wear loose clothing or jewelry. They can be caught in moving parts. Rubber gloves
and substantial, non-skid footwear are recommended when working outdoors. Wear protective hair covering to
contain long hair.
JUS500IB_JUS500IBCA_ManualENFRSP_040518.indd 2-3 4/5/2018 10:03:01 AM
4 5
Do not connect the clamp to the carburetor, fuel lines or sheet-metal body parts. Connect to a heavy gauge
metal part of the frame or engine block. Refer to the automobile owner’s manual.
• If the connections to the battery’s POSITIVE and NEGATIVE terminals are incorrect, the Reverse Polarity
Indicator will light (red) and the unit will sound a continuous alarm until the clamps are disconnected.
Disconnect clamps and reconnect to battery with correct polarity.
• Always disconnect the NEGATIVE (BLACK) jumper cable first, followed by the POSITIVE (RED) jumper cable,
except for positive grounded systems.
• Do not expose battery to fire or intense heat since it may explode. Before disposing of the battery, protect
exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result in injury or fire).
• Place this unit as far away from the battery as cables permit.
• Never allow battery acid to come in contact with this unit.
• Do not operate this unit in a closed area or restrict ventilation in any way.
• IMPORTANT: This unit is delivered in a partially charged state. Fully charge unit with a household extension
cord (not supplied) for a full 48 hours before using for the first time. You cannot overcharge the unit using the
AC charging method.
• All ON/OFF switches should be in the OFF position when the unit is charging or not in use. Make sure all
switches are in the OFF position before connection to a power source or load.
• This system is designed to be used only on vehicles with a 12 volt DC battery system. Do not connect to a 6
volt or 24 volt battery system.
• This system is not designed to be used as a replacement for a vehicular battery. Do not attempt to operate a
vehicle that does not have a battery installed.
• Excessive engine cranking can damage a vehicle’s starter motor. If the engine fails to start after the
recommended number of attempts, discontinue jump-start procedures and look for other problems that may
need to be corrected.
• Do not use this jump-starter on a watercraft. It is not qualified for marine applications.
• Although this unit contains a non-spillable battery, it is recommended that unit be kept upright during storage,
use and recharging. To avoid possible damage that may shorten the unit’s working life, protect it from direct
sunlight, direct heat and/or moisture.
SPECIFIC SAFETY INSTRUCTIONS FOR COMPRESSORS
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
Never leave the compressor
unattended while in use.
WARNING: BURST HAZARD:
• Carefully follow instructions on articles to be inflated.
• Never exceed recommended pressures. Bursting articles can cause serious injury.
• Always check pressure with the pressure gauge.
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:
Do not operate compressor continuously for longer than approximately 10 minutes, depending on
ambient temperatures, as it may overheat. In such event, compressor may automatically shut down.
Turn off the Compressor Power Switch immediately and restart after a cooling down period of
approximately 30 minutes.
FIRST AID
•
Skin:
If battery acid comes in contact with skin, rinse immediately with water, then wash thoroughly with soap
and water. If redness, pain, or irritation occurs, seek immediate medical attention.
•
Eyes:
If battery acid comes in contact with eyes, flush eyes immediately, for a minimum of 15 minutes and
seek immediate medical attention.
Read And Understand This Instruction Manual Before Using This Unit.
SAVE THESE INSTRUCTIONS
WARNING: TO REDUCE THE RISK OF INJURY:
Follow these instructions and those published by the battery manufacturer and manufacturer of any
equipment you intend to use with this unit. Review cautionary markings on these products and on
engine.
a) the pins of extension cord are the same number, size and shape as those in the charger,
b) the extension cord is properly wired and in good electrical condition,
c) the wire size is large enough for the AC rating of the charger as indicated in the table on page 3.
• Do not operate unit with damaged cord or plug; or if the unit has received a sharp blow, been dropped, or
otherwise damaged in any way. Do not disassemble the unit; take it to a qualified service technician when
service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire, and will void
warranty.
• Use of an attachment not supplied, recommended or sold by manufacturer specifically for use with this unit
may result in a risk of electrical shock and injury to persons.
• NEVER submerge this unit in water; do not expose it to rain, snow or use when wet.
• To reduce risk of electric shock, disconnect the unit from any power source before attempting maintenance or
cleaning. Turning off controls without disconnecting will not reduce this risk.
• Do not insert foreign objects into the USB outlet.
WARNING: RISK OF EXPLOSIVE GASES
• Working in the vicinity of a lead acid battery is dangerous. Batteries generate explosive gases during normal
battery operation. For this reason, it is of the utmost importance that each time before using the jump-starter
you read this manual and follow instructions exactly.
• To reduce the risk of battery explosion, follow these instructions and those published by the battery
manufacturer and manufacturer of any equipment you intend to use in the vicinity of the battery. Review
cautionary markings on these products and on the engine.
• This equipment employs parts (switches, relays, etc.) that produce arcs or sparks. Therefore, if used in a
garage or enclosed area, the unit MUST be placed not less than 18 inches above the floor.
• THIS UNIT IS NOT FOR USE BY CHILDREN AND SHOULD ONLY BE OPERATED BY ADULTS.
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• Pull by plug rather than cord when disconnecting the 120V AC Charging Adapter from the unit.
• NEVER ATTEMPT TO JUMP-START OR CHARGE A FROZEN BATTERY.
• To recharge this unit, use only the supplied AC Charging Adapter.
• Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump-started. Before
jump-starting, read the vehicle’s owner’s manual to confirm that external-starting assistance is suitable.
• When working with lead acid batteries, always make sure immediate assistance is available in case of accident
or emergency.
• Always have protective eyewear when using this product: contact with battery acid may cause blindness and/or
severe burns. Be aware of first aid procedures in case of accidental contact with battery acid.
• Have plenty of fresh water and soap nearby in case battery acid contacts skin.
• If battery acid contacts skin or clothing, wash immediately with soap and water for at least 10 minutes and get
medical attention immediately.
• Never smoke or allow a spark or flame in vicinity of vehicle battery, engine or power station.
• Remove personal metal items such as rings, bracelets, necklaces and watches when working with a lead acid
battery. A lead acid battery can produce a short circuit current high enough to weld a ring, or similar metal
object, to skin, causing a severe burn.
• Do not wear vinyl clothing when jump-starting a vehicle when jump-starting a vehicle, friction can cause
dangerous static-electrical sparks.
• Jump-start procedures should only be performed in a safe, dry, well-ventilated area.
• Always store battery clamps when not in use. Never touch battery clamps together. This can cause dangerous
sparks, power arcing and/or explosion.
• When using this unit close to the vehicle’s battery and engine, stand the unit on a flat, stable surface, and be sure
to keep all clamps, cords, clothing and body parts away from moving vehicle parts.
• Never allow red and black clamps to touch each other or another common metal conductor — this could
cause damage to the unit and/or create a sparking/explosion hazard.
a) For negative-grounded systems, connect the POSITIVE (RED) clamp to the POSITIVE ungrounded battery
post and the NEGATIVE (BLACK) clamp to the vehicle chassis or engine block away from the battery. Do not
connect the clamp to the carburetor, fuel lines or sheet-metal body parts. Connect to a heavy gauge metal
part of the frame or engine block. Refer to the automobile owner’s manual.
b) For positive-grounded systems, connect the NEGATIVE (BLACK) clamp to the NEGATIVE ungrounded
battery post and the POSITIVE (RED) clamp to the vehicle chassis or engine block away from the battery.
JUS500IB_JUS500IBCA_ManualENFRSP_040518.indd 4-5 4/5/2018 10:03:01 AM
6 7
CAUTION: RISK OF PROPERTY DAMAGE:
Failure to keep the battery charged will cause permanent
damage and result in poor jump starting performance.
Charging/Recharging Using the 120 Volt AC Charger and a Standard Household
Extension Cord (not included)
1. Lift the AC charger cover located on the front of the unit and connect an extension cord to the unit. Plug the
other end of the cord into a standard 120 volt AC wall outlet.
2. Charge until one red, two yellow and one green LED Battery Status Indicators light or flash.
3. Once fully charged, disconnect the extension cord.
Note:
The unit cannot be overcharged using the AC method.
JUMP-STARTER
This Jump-Starter is equipped with an ON/OFF Power Switch. Once the connections are properly made, turn the
switch ON to jump-start the vehicle.
1. Turn OFF vehicle ignition and all accessories (radio, A/C, lights, connected cell phone chargers, etc.). Place
vehicle in “park” and set the emergency brake.
2. Make sure the Jump-Starter Power Switch is turned to OFF.
3. Remove jumper clamps from clamp tabs. Connect the red clamp first, then the black clamp.
4. Procedure for jump-starting a NEGATIVE GROUNDED SYSTEM (negative battery terminal is
connected to chassis) (MOST COMMON)
4a. Connect positive (+) red clamp to vehicle battery’s positive terminal.
4b. Connect negative (–) black clamp to chassis or a solid, non-moving, metal vehicle component or body
part. Never clamp directly to negative battery terminal or moving part. Refer to the automobile owner’s
manual.
5. Procedure for jump-starting POSITIVE GROUND SYSTEMS
Note:
In the rare event that the vehicle to be started has a Positive Grounded System (positive battery terminal is connected to
chassis), replace steps 4a and 4b above with steps 5a and 5b, then proceed to step 6.
5a. Connect negative (–) black clamp to vehicle battery’s negative terminal.
5b. Connect positive (+) red clamp to vehicle chassis or a solid, non-moving, metal vehicle component or
body part. Never clamp directly to Positive battery terminal or moving part. Refer to the automobile
owner’s manual.
6. When clamps are connected properly, turn the Jump-Starter Power Switch to ON.
7. Turn ON the ignition and crank the engine in 5-6 second bursts until engine starts.
8. Turn the Jump-Starter Power Switch back to the OFF position.
9. Disconnect the negative (–) engine or chassis clamp first, then disconnect the positive (+) battery clamp.
FOLLOW ALL SAFETY INSTRUCTIONS FOUND IN THIS MANUAL.
CAUTIONS: RISK OF PROPERTY DAMAGE
• If the connections to the battery’s POSITIVE and NEGATIVE terminals are incorrect, the Reverse Polarity
Indicator will light (red) and the unit will sound a continuous alarm until the clamps are disconnected.
Disconnect clamps and reconnect to battery with correct polarity.
• If vehicle fails to start, turn OFF the ignition, turn OFF the Jump-Starter Power Switch, disconnect the jump-
start system’s leads and contact a qualified technician to investigate why the engine did not start.
• Recharge this unit fully after each use.
WARNINGS
• Jump-Starter Power Switch should be off prior to jump-starting.
• This power system is to be used ONLY on vehicles with 12 volt DC battery systems.
• Never touch red and black clamps together — this can cause dangerous sparks, power arcing, and/or
explosion.
• Vehicles that have on-board computerized systems may be damaged if vehicle battery is jump-started. Before
jump-starting this type of vehicle, read the vehicle manual to confirm that external-starting assistance is
advised.
• Excessive engine cranking can damage the vehicle‘s starter motor. If the engine fails to start after the
recommended number of attempts, discontinue jump-start procedure and look for other problems that need to
be corrected.
• After use, turn the Jump-Starter Power Switch OFF.
INTRODUCTION
Thank you for choosing the
500 Amp Jump-Starter with Compressor
. This compact jump-starter is unique
in the amount of energy it can supply for its size. The internal battery is a high density sealed, lead-acid battery
that stores and delivers energy comparable to full sized ordinary jump-starters. Please read this guide carefully
before use to ensure optimum performance and avoid damage to the unit or items that you are using it with.
The
500 Amp Jump-Starter
is a compact, durable, portable jump-start system for vehicles that have a
standard 12 volt battery system. This self-contained, rechargeable system will start most vehicles without the
need for a host vehicle or 12 volt DC power supply.
FEATURES
1. Negative (–) Black Clamp
2. Positive (+) Red Clamp
3. Battery Charge Level Pushbutton
4. USB Power On Indicator
5. USB Power Port
6. USB on/off switch
7. LED Battery Status Indicators
8. Built-in 120 Volt AC Charger (under protective
cover)
9. Adapter Nozzle Storage
10. Compressor on/off switch
11. Air Pressure Gauge
12. Cable Storage
13. Area Light Power Button
14. Built-in LED Area Light
15. Reverse Polarity Indicator
16. Jump-Starter Power Switch
17. Air Hose and SureFit® Nozzle Connector (back of
unit)
2
1
5 346
8
9
10
11
7
12
17
14
13
15
16
CHARGING/RECHARGING
This product has a sealed lead acid battery. For maximum battery life, we recommend the Jump-Starter be kept
fully charged at all times. Recharge after purchase, before first use, immediately after each use, and once a
month if not used. Failure to do this may reduce the battery life dramatically. To check the battery charge status
at any time, press the Battery Charge Level Pushbutton.
When the battery is overly discharged and if the green LED is lit when the charger is plugged in, this indicates
the battery is at a high impedance stage.
In this event, recharge the unit and leave the unit charging for a period of 24-48 hours before use.
Note:
This unit is delivered in a partially charged state – you must fully charge it after purchase and before using it for the first time. Initial
AC charge should be for 24 hours.
JUS500IB_JUS500IBCA_ManualENFRSP_040518.indd 6-7 4/5/2018 10:03:02 AM
8 9
Problem
Solution
Unit fails to Jump-Start • Make sure unit’s power switch is in the ON position.
• Check that Jump-Starter has a full charge. Recharge unit if necessary.
• Make sure a proper polarity cable connection has been established.
• Leave charger plugged in and keep unit on charge for 24-48 hours.
Portable Compressor will not inflate • Make sure the Compressor Power Switch is in the on position.
• Check that jump-starter has a full charge. Recharge unit if necessary.
• Make sure the SureFit® nozzle connector is securely screwed on to
the valve stem when attempting to inflate tires; or that the nozzle
adapter is securely screwed into the SureFit® nozzle connector and is
inserted properly into the item to be inflated on all other inflatables.
• The compressor may be overheated. Press the compressor power
switch to turn the compressor off. Restart after a cooling down
period of approximately 30 minutes.
USB Power Port will not power
appliance
• Make sure the USB Charging Port Power Button is in the ON position.
• Make sure the appliance being powered does not draw more than
500mA.
• Some USB-powered household electronics will not operate with this
USB Power Port. Check the manual of the corresponding electronic
device to confirm that it can be used with this type of USB power port.
• Check that Jump-Starter has a full charge. Recharge unit if necessary.
LED Area Light does not come on • Make sure the LED Area Light ON/OFF button is in the ON position
• Check that Jump-Starter has a full charge. Recharge unit if necessary.
CARE AND MAINTENANCE
All batteries lose energy from self-discharge over time and more rapidly at higher temperatures. When the unit
is not in use, we recommend that the battery is charged at least every 30 days.
Never submerge the unit in water. If the unit gets dirty, gently clean the outer surfaces of the unit with a soft cloth
moistened with a mild solution of water and detergent.
There are no user-replaceable parts. Periodically inspect the condition of adapters, connectors and wires.
Contact manufacturer to replace any components that have become worn or broken.
Battery replacement/disposal
BATTERY REPLACEMENT
The battery should last the service life of the unit. Service life is dependent on a number of factors
including but not limited to the number of recharge cycles, and proper care and maintenance of the
battery by the end user. Contact manufacturer for any information you may need.
SAFE BATTERY DISPOSAL
Contains a maintenance-free, sealed, non-spillable, lead acid battery, which must be
disposed of properly. Recycling is required. Failure to comply with local, state and federal
regulations can result in fines, or imprisonment.
Please recycle.
WARNINGS:
• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting
(shorting can result in injury or fire).
• Do not expose battery to fire or intense heat as it may explode.
ACCESSORIES
Recommended accessories for use with this unit may be available from the manufacturer. If you need assistance
regarding accessories, please contact manufacturer at 1-877-571-2391.
WARNING:
The use of any accessory not recommended for use with this appliance could be hazardous.
PORTABLE COMPRESSOR
The built-in 12 volt DC compressor can be used to inflate all vehicle tires and recreational inflatables. An inflator
nozzel, sports needle and bicycle racing tire adapter (Presta Stem Adapter) are included. Each one of these
compressor adapters connect to the SureFit® nozzle connector at the end of the hose. The compressor adapters
are stored inside a small compartment near the compressor power switch. The Compressor On/Off Switch is
located on the front of the unit near the pressure gauge. The Air Pressure Gauge is located on the front of the
unit above the control panel. The compressor can operate long enough to fill up to 3 average sized tires before
the battery must be recharged.
The compressor may be used by removing the air hose from the storage hatch and if required, fitting an
appropriate nozzle to the air hose. Return hose to the storage compartment after use.
WARNING – TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE: Follow all safety
instructions found in the “Specific Safety Instructions For Compressors” section of this instruction
manual.
Inflating Tires or Products With Valve Stems
1. Screw the SureFit® nozzle connector onto the valve stem. Do not overtighten.
2. Turn on the Compressor Power Switch.
3. Check pressure with the pressure gauge.
4. When desired pressure is reached, turn off the Compressor Power Switch.
5. Unscrew and remove the SureFit® nozzle connector from the valve stem.
6. Allow the unit to cool, then recharge before storing away.
7. Store the compressor hose and nozzle connector in the storage compartment.
Inflating Other Inflatables Without Valve Stems
Inflation of other items requires use of one of the nozzle adapters.
1. Select the appropriate nozzle adapter (i.e, needle).
2. Screw the adapter into the SureFit® nozzle connector. Do not overtighten.
3. Insert the adapter into item to be inflated.
4. Turn on the Compressor Power Switch — inflate to desired pressure or fullness.
IMPORTANT NOTE:
Small items such as volleyballs, footballs, etc. inflate very rapidly. Do not over-inflate.
5. When desired pressure is reached, turn off the Compressor Power Switch.
6. Disconnect the adapter from the inflated item.
7. Unscrew and remove the adapter from the SureFit® nozzle connector.
8. Allow the unit to cool, then recharge before storing away.
9. Store the compressor hose, nozzle connctor and adapter in the storage compartment.
USB POWER PORT
1. Push the USB Power Port On Pushbutton to turn the USB Port ON.
2. Plug the USB-powered device into the inverter’s USB Charging Port and operate normally.
Notes:
This unit’s USB Power Port does not support data communication. It only provides 5 volts/500mA DC power to an external USBpowered device. Make sure the USB Charging Port ON/OFF Pushbutton is in the OFF position when the unit is being recharged or
stored.
Some household USB-powered electronics will not operate with this unit.
LED AREA LIGHT
The Area Light is controlled by the Area Light Power Button on the front panel of the unit. Make sure the lamp is
turned OFF when the unit is being recharged or stored.
TROUBLESHOOTING
Problem
Solution
Unit will not charge • Make sure the power switch is in the off position.
• Make sure a suitable gage extension cord is properly connected to
both the unit and a functioning AC outlet.
JUS500IB_JUS500IBCA_ManualENFRSP_040518.indd 8-9 4/5/2018 10:03:02 AM
Loading...