Black & Decker Je55 Instruction Manual [ar]

Centrifugal Juice Extractor

First Use Safety Recommendation

Please read through this booklet for safe and efficient use of the appliance. We urge you to read all detailed instructions even if you are familiar with using this appliance.

Keep this guide handy for future reference.

JE55

ENGLISH

IMPORTANT SAFEGUARDS

While using electrical appliances, in order to reduce the risk of fire, electric shock, and/or injury to persons, basic safety precautions should be followed, including the following:

• Read all instructions carefully.

• To protect against electrical shock, DO NOT IMMERSE the appliance, cord set or plug in water or other liquids.

• Close supervision is necessary when any appliance is used by or near children.

• Unplug from outlet when not in use. Unplug before cleaning, changing accessories or approaching parts which move in use.

• Never pull the cord when unplugging from the power outlet.

• Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions or has been damaged in any manner. Return appliance to an authorized service facility for examination, repair or adjustment.

• Do not abuse the cord. Never carry the appliance by the cord or pull it to disconnect it from the power outlet. Always grip the plug & pull to disconnect.

• Do not use outdoors.

• Do not let cord hang over edge of table or counter, or touch hot surfaces.

• Do not place on or near a hot gas or electric burner, or in a heated oven.

• Do not use the appliance for other than the intended use.

• The use of accessory attachments not recommended by this appliance manufacturer may cause hazards.

• For household use only.

• Do not leave this appliance unattended in use.

• To avoid a circuit overload, do not operate another high wattage appliance on the same circuit.

• If an extension cord is used, please ensure it is correctly wired and rated for use with this appliance. If in doubt, consult a qualified electrician. The extension cord should be arranged so that it will not drape over the counters or table tops where it could be pulled by children or tripped over.

• Do not attempt to repair this appliance yourself; instead take it to your nearest Black & Decker-owned or Authorised Service Centre for repair.

SAVE THESE INSTRUCTIONS

-2-

Parts Identification

1. Motor housing

2. Speed selector

3. Pulp collector

4. Strainer

5. Cover

6. Tray

7. Latch - right

8. Latch – left

9. Spout

10. Cord storage

11. Pusher

12. Jug

13. Foam separator

14. Sieve

15. Sieve housing

16. Sieve adaptor

ENGLISH

11 12 13

1514 16

Fig. A

Fig. B

-3-

ENGLISH

FEATURES

• 450W

• 2 speed operation

• 0.7 litre jug

• Removable pulp collector

• Stainless steel sieve

• Removable tray

• Jug

• Cord storage

FigA-Beforefirst use:

Before using your Juicer for the first time, make sure it is disconnected from the electrical supply, then remove all packaging from the sieve & pulp container.

To remove the packaging, open the right-hand latch (7), then the left-hand latch (8).

Lift the cover (5) & tray (6) from the appliance. Remove the packing from the sieve (14) and from

the pulp collector (3) and strainer (4). Pull the sieve housing & sieve from the Juicer. All parts must be cleaned as recommended in the

section “How to take care of your Juicer”. The motor housing must only be cleaned with a

damp cloth, and dried thoroughly before use. Inspect the sieve for signs of damage. Note: Do not use the appliance if the rotating

sieve is damaged.

Fig B - How to assemble your Juice Extractor

Place the sieve housing (15) on the motor housing (1), then place the sieve (14) into the sieve housing, pressing it onto the sieve adaptor (16).

Fit the strainer (4) into the pulp collector (3). Locate lower hinge of the pulp collector into the hole in the motor housing, ensuring the tab on the pulp collector is located in the slot in the motor housing.

Fit the cover (5), ensuring that the upper hinge of the pulp collector locates in the hole in the cover.

Close the right-hand latch (7) and the left-hand latch (8).

Fit the tray (6) onto the cover (5). This can be fitted as a cover for storage, or inverted to act as a tray where ingredients can be temporarily stored before juicing.

Place the jug (12) under the spout (9).

How to use your Juicer

This appliance is designed to extract juice from fruits & vegetables.

Do not use this appliance for any other purpose. For indoor domestic use only. Prepare material to be processed by washing

thoroughly and peeling as required. Remove all pips and large seeds. Cut large fruits or vegetables into small pieces which will fit the inlet chute.

Smaller items of food can be placed on the tray ready to be directed into the chute with the pusher (11).

Make sure the speed selector (2) is in the ‘’0’’ (OFF) position, then the plug cord-set into a power outlet.

Note: Make sure that the voltage shown on the underside of the motor housing corresponds with the local supply voltage.

Rotate the speed selector to position 1 or 2 as required. Low speed should be used for soft fruits and high speed for harder fruits.

Check the jug and pulp collector are in place, and feed the ingredients into the inlet chute. The pusher (11) can be used to gently guide the ingredients down the inlet slot. Do not overload the machine. Too much pressure may cause material to jam the inlet chute.

If a blockage occurs, NEVER USE FINGERS OR ANY OBJECT OTHER THAN THE PUSHER TO CLEAR THE INLET CHUTE.

If the food cannot be dislodged, turn the speed selector to the “0” position (OFF) and UNPLUG

the POWER CORD FROM OUTLET.

Remove the cover as described in “Before first use” and clear the blockage. Replace the cover, re-connect the Juicer to the electrical supply & resume juicing.

When juicing is completed, the switch should be returned to the off (0) position, and allow the motor to come to a stop. The jug should be left in place until the juice stops flowing from the spout.

UNPLUG POWER CORD FROM THE OUTLET,

and disassemble the juice extractor. Empty the pulp from the collector and clean all parts as soon as possible after you have finished processing.

-4-

Emptying the jug

Pay attention to the jug while juicing to prevent spills through overfilling. If the jug is full, rotate the speed selector (2) to the ‘’0’’ (OFF) position, remove the jug & pour the contents into a separate container.

The foam separator (13) can be used to keep any foam in the jug. Return the jug to its position and continue juicing.

Emptying the pulp collector / strainer

If the pulp collector (3) becomes full before all of the ingredients are used, rotate the speed selector (2) to the ‘’0’’(OFF) position and unplug the Juicer.

Take hold of the pulp collector at the left edge, & pull it away from the motor housing. The pulp collector will swing open on its hinges. The strainer (4) can be removed by lifting the tab at the back. The pulp can be discarded and the strainer returned to the pulp collector, which can then be closed again.

If the pulp collector (3) needs to be emptied, rotate the speed selector (2) to the ‘’0’’ (OFF) position and unplug the Juicer.

Remove the cover (5) as described in “Before first use” and lift the pulp collector from its location. Empty it into a suitable container & re-fit it to the motor housing. Replace the lid, making sure the latches are closed, reconnect the unit to the power supply & re-commence juicing.

How to take care of your Juicer

The Juicer must be cleaned thoroughly after each use.

Make sure the appliance is switched ‘OFF’ and unplug the unit from the power supply before cleaning.

NOTE: NEVER IMMERSE the motor housing (1) IN WATER OR ANY OTHER LIQUID.

To clean motor housing, wipe clean with a damp cloth. Allow to dry thoroughly before re-using or storing. The removable parts of the juice extractor assembly should be washed promptly after each use with a mild detergent in warm water. These parts are not dishwasher safe and must be hand washed.

ENGLISH

Use a brush to scrub pulp residue from the cutting teeth and strainer holes of the sieve (14).

After washing, rinse and allow all parts to dry thoroughly before re-assembly and storage.

Never use a metal brush to clean the sieve.

Take care when handling the sieve as the blades are sharp.

Warning:

Do not use the appliance if the rotating sieve is damaged.

Protecting the environment

Separate collection. This product must not

be disposed of with normal household waste. Should you find one day that your Black & Decker

product needs replacement, or if it is of no further use to you, do not dispose it off with other household waste. Make this product available for separate collection.

Separate collection of used products and

packaging allows materials to be recycled and used again. Use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials.

Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product.

Black & Decker provides a facility for the collection and recycling of Black & Decker products once they have reached the end of their working life. To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf. You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. A list of authorised Black & Decker repair agents and full details of our after-sales service and contact are available on the Internet at: www.2helpU.com

-5-

+ 11 hidden pages