Page 1
8 1
Distributed by: Directed Electronics
Address: 44 Translink Drive, Keilor Park Victoria Australia 3042
PH: + 61 03 8331 4800 Email: service@directed.com.au
Baccus Worldwide LLC
Weena 290, 3012 NJ Rotterdam or
Postbus 819, 3000 AV Rotterdam
+31(0)10 282 16 11
Cat. # J312BAU September 2016
RD091216 Printed in China
300 AMP BATTERY JUMP-STARTER
INSTRUCTION MANUAL
J312BAU_Manual_091216.indd 8-1 9/12/2016 11:59:47 AM
Page 2
32
INSTRUCTION MANUAL
INTENDED USE
Your Black & Decker jump starter is designed to
provide additional power to lead-acid batteries when
starting car engines. This product is intended for
household, consumer use only.
SAFETY INSTRUCTIONS
Warning!
When using appliances, basic safety
precautions, including the following, should always be
followed to reduce the risk of fire, leaking batteries,
personal injury and material damage.
•Read all of this manual carefully before using the
appliance.
•The intended use is described in this manual.
The use of any accessory or attachment or the
performance of any operation with this appliance
other than those recommended in this instruction
manual may present a risk of personal injury.
•Retain this manual for future reference.
Using the jump starter
Always take care when using the appliance.
•This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
•The appliance is not to be used as a toy.
• Use in a dry location only. Do not allow the
appliance to become wet.
•Do not immerse the appliance in water.
•Do not open body casing. There are no user-
serviceable parts inside.
•Do not operate the appliance in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust.
•To reduce the risk of damage to plugs and cords
never pull the cable to remove the plug from a
socket outlet.
•Never smoke or allow a spark or flame in vicinity of
vehicle battery, engine or this unit.
•Place this unit as far away from the battery as cables
permit.
•Never allow battery acid to come in contact with this
unit.
•Do not operate this unit in a closed area or restrict
ventilation in any way.
Using the 12 volt dc accessory outlet
•Do not use this unit to operate appliances that need
more than 5 amps to operate from the 12 volt dc
accessory outlet.
•Do not insert foreign objects into the 12 volt dc
accessory outlet.
After use
•When not in use, the appliance should be stored in a
dry, well ventilated place out of the reach of children.
•Children should not have access to stored
appliances.
•When the appliance is stored or transported in a
vehicle it should be placed in the boot or restrained
to prevent movement following sudden changes in
speed or direction.
•The appliance should be protected from direct
sunlight, heat and moisture.
Inspection and repairs
•Before use, check the appliance for damaged or
defective parts. Check for breakage of parts, damage
to switches and any other conditions that may affect
its operation.
•Do not use the appliance if any part is damaged or
defective.
•Have any damaged or defective parts repaired or
replaced by the manufacturer.
•Never attempt to remove or replace any parts other
than those specified in this manual.
The following symbols are marked on
the appliance:
Read all of this instruction manual
carefully.
Reverse polarity indicator.
The unit is intended for indoor use only.
Specific safety instructions for jump
starters
•Vehicles may have electrical and electronic systems
(e.g. engine management system, mobile phone)
that may be damaged if subjected to high starting
voltages and voltage peaks. Before connecting the
appliance to the vehicle read the vehicle’s owner’s
manual to confirm that external-starting assistance
is allowed.
•Follow these instructions and those published by
the battery manufacturer, vehicle manufacturer
and manufacturer of any equipment you intend to
use with this unit. Review warning labels on these
products and on the vehicle.
•This appliance is not designed to be used as a
replacement for a vehicular battery. Do not attempt
to operate a vehicle that does not have a battery
installed.
•The appliance must only be connected to a 12V leadacid battery. Do not use the appliance for charging
11
12
1098753 4
1 2
6
13
J312BAU_Manual_091216.indd 2-3 9/12/2016 11:59:47 AM
Page 3
4 5
dry-cell batteries that are commonly used with home
appliances. These batteries may burst and cause
injury to persons and damage property.
•Check the polarity of the vehicle battery terminals
before connecting the appliance. Always disconnect
the negative (black) jumper cable first: followed by
the positive (red) jumper cable.
•The jump-starter power switch should be in the off
position before connection to a power source or
load, when the unit is charging and when not in use.
•Never allow the red and black clamps to touch each
other or another common metal conductor. This
could cause damage to the appliance and/or create a
sparking/explosion hazard. Always store the battery
clamps in the built-in holders when not in use.
•When using this unit in proximity to the vehicle’s
battery and engine, stand the unit on a flat, stable
surface, and be sure to keep all clamps, cords,
clothing and body parts away from moving parts of
the vehicle.
•This appliance contains a sealed lead-acid battery. It
is recommended that the appliance is laid flat during
storage, use, and recharging.
•Excessive engine cranking can damage a vehicle’s
starter motor. If the engine fails to start after the
recommended number of attempts, discontinue
jump-start procedures and look for other problems
that may need to be corrected.
•Do not use this jump-starter on a watercraft. It is not
qualified for marine applications.
Warning! Burst hazard:
Do not use the unit for
charging dry-cell batteries that are commonly used
with home appliances. These batteries may burst
and cause injury to persons and damage property.
Use the unit for charging/boosting a lead-acid battery
only. It is not intended to supply power to a lowvoltage electrical system other than in a starter-motor
application.
Warning!
Explosive gas may be vented from lead acid
batteries when charging. The battery must be placed
in a well-ventilated area and you must remove any
sources of ignition when conducting jump starting
procedures.
•To reduce the risk of electric shock, disconnect the
appliance from any power source before attempting
maintenance or cleaning. Turning off controls without
disconnecting the appliance will not reduce this risk.
•Make sure the appliance is disconnected from all
charging power sources before beginning the jump
start procedure.
Additional safety instructions for
batteries and chargers
BATTERIES
•Never attempt to open for any reason.
•Do not expose the battery to water.
•Do not store in locations where the temperature may
exceed 40°C.
•Charge only at ambient temperatures between 4°C
and 40°C.
•Charge only using the chargers provided with the
appliance.
•When disposing of batteries, follow the instructions
given in the section “Protecting the environment”.
•Under extreme conditions, battery leakage may
occur. When you notice liquid on the batteries,
carefully wipe the liquid off using a cloth. Avoid skin
contact.
CHARGERS
The following symbols are found on your mains
charger:
Your charger is double
insulated; therefore no earth
wire is required.
Your charger is a switch mode
power supply unit.
Your charger incorporates
a short-circuit-proof safety
isolating transformer
(inherently or non-inherently)
Indication of correct connection
of your charger.
The charger is intended for
indoor use only.
Your charger meets the Energy
Efficiency Level V standard
for no-load condition electric
power consumption and
average active efficiency of
external power supplies.
Your charger is rated to IP20
degree of protection provided
by the enclosure.
Your charger has been designed for a specific voltage.
Always check that the mains voltage corresponds to
the voltage on the rating plate.
Warning!
Never attempt to replace the charger unit
with a regular mains plug.
Use your Black & Decker charger only to charge the
battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and
damage.
•Never attempt to charge non-rechargeable batteries.
•Have defective cords replaced immediately.
•Do not expose the charger to water.
•Do not open the charger.
•Do not probe the charger.
•The battery must be placed in a well ventilated area
when charging.
Electrical safety
Always check that the power supply corresponds to
the voltage on the rating plate.
•If the supply cord is damaged, it must be replaced
by the manufacturer in order to avoid a hazard.
PERSONAL SAFETY
Always have protective eyewear when using this
product: contact with battery acid may cause
blindness and/or severe burns. Be aware of first aid
procedures in case of accidental contact with battery
acid.
Avoid touching the eyes while working with a battery.
Acid, acid particles or corrosion may get into the eyes.
Have plenty of fresh water and soap nearby in case
battery acid contacts skin.
Remove personal metal items such as rings, bracelets,
necklaces and watches when working with a lead-acid
battery. A lead-acid battery can produce a short circuit
current high enough to cause a severe burn.
Be extra cautious to reduce the risk of dropping a
metal object onto the battery. This might cause sparks
or short-circuit the battery or other electrical part,
which can cause an explosion.
Warning!
Battery fluid is a diluted sulphuric acid and
may cause personal injury or damage to property. In
case of skin or eye contact, follow the instructions
below.
•In case of skin contact, immediately rinse with water.
If redness, pain or irritation occurs seek medical
attention.
•In case of eye contact, rinse immediately with clean
water and seek immediate medical attention.
FEATURES
1. 12V dc accessory outlet (under protective cover)
2. Jump-starter power switch
3. Positive (+) red clamp
4. USB power indicator
5. USB power button
6. USB port (under protective cover)
7. Battery status LED indicators
8. Battery power level button
9. Reverse polarity indicator
10. Negative (–) black clamp
11. Rubber grip handle
12. Charging socket
13. Mains charging adapter
CHARGING THE UNIT
This unit is shipped in a partially charged state.
•Charge the unit before first use using the mains
charging adapter for 24 hours.
Lead-acid batteries need to be kept fully charged and
well maintained to ensure they continue to function
properly. All batteries lose energy from self-discharge
over time and more rapidly at higher temperatures.
When the unit is not in use, manufacturer recommend
that the battery is charged at least every 30 days.
•Check the battery charge level by pressing the
battery status button. The battery status LED
indicators will show the level of battery charge.
When only one red LED lights, charge the unit.
•Make sure all other unit functions are turned off
during recharging, as this can slow the recharging
process.
Note:
Charging the battery after each use will prolong the battery
life; frequent heavy discharges between charges and/or
overcharging will reduce battery life.
Important!
When the battery is overly discharged and
if the green LED is lit when the charger is plugged in,
this indicates the battery is at a high impedance stage.
In this event, recharge the unit for a period of 24
hours before use.
•Insert the jack of the mains charging adapter into the
charging socket on the back of the unit.
•Insert the mains charging adapter plug into a mains
power socket.
•Charge until the green battery status LED indicator
lights solid or flashes.
•Disconnect the mains charging adapter from the
mains power socket and then remove the plug of
mains charging adapter from the charging socket
on the back of the unit. Press the battery status
button. If all 3 status lights illuminate, the unit is fully
charged. Store the mains charging adapter in a safe
place.
USE
Using the jump-starter
1. Turn off the vehicles ignition and all accessories
before making any connections.
2. Make sure that the jump-starter power switch is
turned off.
3. Check polarity of battery posts. Positive (POS, P,
+) battery post usually has larger diameter than
negative (NEG, N, –) post.
4. Determine which post of the battery is grounded
(connected to the chassis). If negative post is
grounded (as in most vehicles), see 5. If positive
post is grounded, see 6.
5. For negative-grounded vehicle, connect positive
(red) clamp from battery charger to positive
(POS, P, +) ungrounded post of battery. Connect
J312BAU_Manual_091216.indd 4-5 9/12/2016 11:59:48 AM
Page 4
6 7
negative (black) clamp to vehicle chassis or
engine block away from battery. Do not connect
clip to carburetor, fuel lines, or sheet-metal body
parts. Connect to heavy gauge metal part of the
frame or engine block.
6. For positive-grounded vehicle, connect negative
(black) clamp from battery charger to negative
(NEG, N, –) ungrounded post of battery. Connect
positive (red) clamp to vehicle chassis or engine
block away from battery. Do-not connect clip to
carburetor, fuel lines or sheet-metal body parts.
Connect to a heavy gauge metal part of the frame
or engine block.
Important!
If the connections to the battery’s
positive and negative terminals are incorrect,
the Reverse Polarity Indicator will light and the
unit will sound a continuous alarm until the
clamps are disconnected. Disconnect clamps and
reconnect to battery with correct polarity.
7. Turn the jump-starter power switch to the on
position.
8. Start the vehicle and crank the engine in 3 to 6
second bursts.
Important!
If the engine doesn’t start within 6
seconds let the units internal battery cool for 3
minutes before making another attempt.
9. When the vehicle starts, turn the jump-starter off/
on switch to the off position.
10. Leave the vehicle’s engine running.
11. Disconnect the (–) black clamp connected to the
engine or chassis first, followed by the (+) red
clamp that is connected to the battery positive (+)
terminal.
12. Carefully press the negative (black) jumper cable
wire into the storage channel starting at the end
furthest from the clamp.
13. Clamp the negative (black) clamp onto the clamp
holder.
14. Carefully press the positive (red) jumper cable
wire into the storage channel starting at the end
furthest from the clamp.
15. Clamp the positive (red) clamp onto the clamp
holder.
16. Charge the unit as soon as possible.
17. Make sure that the jump-starter power switch
is turned off while the unit is being charged or
stored.
Using the 12V dc socket
This portable power source can be used with all 12V
dc accessories equipped with a male accessory socket
plug that are rated up to 5 amps.
1. Lift up the cover of the unit’s 12V dc socket.
2. Insert the 12 volt dc plug from the device into
the 12V dc accessory socket on the unit. DO NOT
EXCEED A 5 AMP LOAD.
3. Switch on the device and operate as usual.
4. Periodically press the battery power level button
to check battery status.
Using the USB port
1. Push the USB power button to turn the USB port
on. The USB power indicator will light.
2. Lift up the cover of the USB port.
3. Plug the USB-powered device into the USB port
and operate normally.
4. Periodically press the battery power level button
to check battery status.
Notes:
This unit’s USB port does not support data communication.
It only provides 5 volts/2A dc power to an external USBpowered device.
Make sure the USB power button is in the off position when
the unit is being recharged or stored.
Some household USB-powered electronics will not operate
with this unit.
TROUBLESHOOTING
Problem
Solution
Unit will not
charge
•Make sure the power switch is in
the off position.
•Make sure the jack of the mains
charging adapter is properly
connected to both the unit and a
functioning mains power socket.
Unit fails to
jump-start
•Make sure unit’s power switch is
in the on position.
•Check that jump-starter has
a full charge. Recharge unit if
necessary.
•Make sure a proper polarity cable
connection has been established.
12V dc
accessory
outlet will
not power
appliance
•Make sure the the appliance does
not draw more than 5 amps.
•Check that unit has a full charge.
Recharge unit if necessary.
USB port will
not power
appliance
•Make sure the USB charging
port power button is in the on
position.
•Make sure the the appliance does
not draw more than 2 amps.
•Check that unit has a full charge.
Recharge unit if necessary.
If the unit does not charge or operate after following
the above directions, contact the manufacturer.
MAINTENANCE
This unit has been designed to operate over a long
period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
Warning!
Before performing any maintenance or
cleaning of the unit, unplug it from the power supply.
•From time to time wipe the unit with a damp cloth.
Do not use any abrasive or solvent-based cleaner. Do
not immerse the unit in water.
•Clean the outside case of the jump starter with a soft
cloth and, if necessary, mild soap solution.
•Do not allow liquid to enter the unit’. Do not operate
when the battery charger is wet.
•Keep the cords loosely coiled during storage to
prevent damage to the cords.
PROTECTING THE ENVIRONMENT
Correct disposal of this product
This marking indicates that this product
should not be disposed with other
household waste throughout the EU. To
prevent possible harm to the environment
or human health from uncontrolled
waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return
your used device, please use the return and collection
systems or contact the retailer where the product
was purchased. They can take this product for
environmentally safe recycling.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the
demand for raw materials.
Local regulations may provide for separate collection
of electrical products from the household, at municipal
waste sites or by the retailer when you purchase a
new product.
Lead acid batteries can be recharged many times. At
the end of their useful life, discard batteries with due
care for our environment:
•Do not dispose of the battery in fire, as this may
result in an explosion.
•Lead acid (Pb) batteries are recyclable. They
must not be disposed of with household waste.
The battery must be removed and disposed of in
accordance with local regulations.
•Do not short-circuit the battery terminals.
•Be aware that the battery is heavy.
•If possible, operate the appliance to run the battery
down completely.
•Place the battery in a suitable packaging to ensure
that the terminals cannot be short-circuited.
SPECIFICATIONS
Boost Ampere: 12V dc, 300A
instantaneous
Battery Type: Maintenance-free, sealed
lead acid, 12V dc, 7Ah
dc accessory socket: 12V dc, 5A
USB port: 5V dc, 2A
Mains charging adapter
Input: 100-240V ac, 50/60Hz
Output: 14,5V dc, 750mA
WARRANTY
Our goods come with guarantees that cannot be
excluded under the Australian & New Zealand
Consumer Law. You are entitled to a replacement
or refund for a major failure and compensation
for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of
acceptable quality and the failure does not
amount to a major failure.
Baccus Worldwide LLC is confident of the quality of
its products and offers an outstanding warranty. This
warranty statement is in addition to and in no way
prejudices your statutory rights under the Australian &
New Zealand Consumer Law.
If a Baccus Worldwide LLC product becomes
defective due to faulty materials, workmanship or
lack of conformity, within 24 months from the date
of purchase, Baccus Worldwide LLC guarantees to
replace defective parts, repair products subjected to
fair wear and tear or replace such products to make
sure of the minimum inconvenience to the customer
unless:
•The product has been used for trade, professional or
hire purposes;
•The product has been subjected to misuse or
neglect;
•The product has sustained damage through foreign
objects, substances or accidents;
•Repairs have been attempted by persons other than
Baccus Worldwide LLC service staff.
To claim on this warranty, you will need to submit
proof of purchase and return the allegedly defective
product to Baccus Worldwide LLC’s local market
distributor, at your expense.
Please visit our website www.baccusworldwide.com
to register your new Baccus Worldwide LLC product
and to be kept up to date on new products and special
offers. Further information on the Baccus Worldwide
LLC brand and our range of products is available at
www.baccusworldwide.com.
J312BAU_Manual_091216.indd 6-7 9/12/2016 11:59:48 AM
Loading...