BLACK+DECKER IR2250 Use And Care Manual
PRO-SERIES STEAM IRON
PLANCHA DE VAPOR PRO-SERIES
use and care manual
manual de uso y cuidado
IR2250
Thank you for your purchase!
Gracias por su compra!
IMPORTANT SAFETY INSTRUCTIONS
When using your iron, basic safety precautions should
always be followed, including the following:
www.prodprotect.com/blackanddecker
www.BlackAndDeckerAppliances.com
• READ ALL INSTRUCTIONS BEFORE USING.
• Only use iron for intended use.
• To avoid the risk of electric shock, do not
immerse the iron in water or other liquids.
• Always turn the iron to MIN setting before
plugging in or unplugging from the outlet.
Never pull on the cord to disconnect from
the electrical outlet; instead grasp plug and
pull to disconnect.
• Do not allow cord to touch hot surfaces. Let
iron cool completely before putting away. Coil
the cord loosely around the iron when storing.
• Always disconnect iron from electric outlet
before filling with or emptying water,
cleaning, and when not in use.
• Do not operate the iron if it has been
dropped, if there are visible signs of
damage to the iron or its cord, or if it’s
leaking. To avoid the risk of electric shock,
do not dissemble the iron; take it to a
qualified service person for examination
and repair, or call the appropriate tollfree number on the cover of this manual.
Incorrect reassembly can cause risk of
electric shock when the iron is used.
• Close supervision is necessary for any
appliance being used by or near children.
Do not leave iron unattended when
plugged in or on an ironing board.
• Burns can occur from touching hot metal
parts, hot water, or steam. Use caution
when you turn the iron upside down - there
may be hot water in the reservoir. Avoid
rapid movement of iron to minimize hot
water spillage.
• The iron must be used and rested on a
stable surface.
• When placing the iron on its stand, ensure
that the surface on which the stand is
placed is stable.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory, or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
• Children should be supervised to ensure
that they do not play with the appliance.
SPECIAL INSTRUCTIONS
• To avoid circuit overload, do not operate an
iron on the same circuit with another high
wattage appliance.
• If an extension cord is absolutely
necessary, a minimum 15-ampere cord
should be used. Cords rated for less
amperage can result in a risk of fire or
electrical shock due to overheating. Care
should be taken to arrange the cord so that
it cannot be pulled or tripped over.
SAVE THESE INSTRUCTIONS.
This product is for household use only.
Should you have any questions or concerns with your new product,
please call our Customer Service Line at 1-800-465-6070 (US and
Canada). Please do not return to the store.
Si usted tiene alguna inquietud o pregunta con su producto, por
favor llame a nuestra línea de servicio al cliente una atención
inmediata 1-800-465-6070 (EE.UU/Canadá) 01-800-714-2503
(México). No devuela a la tienda.
POLARIZED PLUG
This appliance has a polarized plug (one blade
is wider than the other). To reduce the risk of
electric shock, this plug is intended to fit into
a polarized outlet only one way. If the plug
does not fit fully into the outlet, reverse the
plug. If it still does not fit, contact a qualified
electrician. Do not attempt to modify the plug
in any way.
2 3
TAMPER-RESISTANT SCREW
Warning: This appliance is equipped with a
tamper-resistant screw to prevent removal
of the outer cover. To reduce the risk of fire
or electrical shock, do not attempt to remove
the outer cover. There are no user-serviceable
parts inside. Repair should be done only by
authorized service personnel.
Note: If the power cord is damaged, it must be
replaced by the manufacturer, its service agent
or similarly qualified person in order to avoid a
hazard. Contact consumer support at the tollfree number listed in the warranty section.
GETTING TO KNOW YOUR
PRO-SERIES STEAM IRON
6
5
4
3
2
HOW TO USE
This product is for household use only.
7
GETTING STARTED
• Remove all labels, tags and stickers attached to the body, cord, or
soleplate of the iron, and remove the plastic band around the power plug.
• Remove and save literature.
FILLING THE WATER TANK
1. With the iron on a flat surface, with the soleplate down, open the
8
9
10
11
water-fill cover.
2. Using a clean measuring cup, pour ordinary tap water into opening
until water reaches the “MAX” level mark on the side of the water
tank. Do not overfill. Close the water-fill cover securely.
Tip: This iron is designed to use ordinary tap water. A mixture of 50%
tap water and 50% distilled water can be used in areas with very hard
water to avoid build-up. It is not recommended to use water with
perfume or scented additives.
3. Stand the iron on the heel rest.
4. To refill at any time during the ironing process, unplug the iron and
follow the above procedure.
USING YOUR IRON
1. Plug the iron into an outlet. The red Power Indicator Light will
12
1
1. Soleplate
2. Spray nozzle
3. Water-fill cover
4. Burst of steam button
5. Spray mist trigger
6. Variable steam selector
7. 360
4 5
°
Pivoting cord
Product may vary slightly from what is illustrated.
8. Power indicator light
9. Variable temperature control dial
and fabric setting guide
10. Water tank
11. Heel rest
12. Auto- Clean
™
button
illuminate on the handle, indicating that the iron is on. Allow a
minute for the iron to heat up before ironing.
2. Read the manufacturer's fabric label for material content and clothing
care recommendations to help select the correct temperature and
steam settings.
3. Select ironing temperature by turning the Variable Temperature
Control Dial to the desired setting. A fabric setting guide is printed
under the iron heel for easy reference. Allow the iron to heat up
about 2 minutes to reach the selected temperature.
Tip: Preheat while in the DRY IRON
Simply slide the Variable Steam Selector all the way to the top (farthest
back) position. This will control sputtering and dripping that may occur
as water heats to temperatures high enough to generate steam.
4. To iron with steam, slide the Variable Steam Selector to the desired
amount of steam. It is recommended that steam NOT be used at
lower temperature settings. For optimal results, follow the Setting
Guide listed on page 6.
setting by turning the steam off.
5. To iron without steam (dry iron), it is not necessary to empty the
water tank. Simply slide the Variable Steam Selector all the way to
the top (farthest back) position.
6. When finished ironing, turn the Steam Selector to the Off/Dry
Iron setting and set the Temperature Control Dial to the minimum
temperature setting. Unplug from the outlet.
7. Stand the iron on its heel rest and allow it to completely cool off
before storing.
SETTING GUIDE
For best results follow manufacturer’s garment care tags for
recommended heat and steam setting instructions.
Setting number Setting name Setting
Description
- - Do not Iron
1 Synthetic Low Heat and
No Steam
2 Nylon and Silk Low Heat and
No Steam
3 Polyester Medium Heat
and No Steam
4 Blend Medium Heat
and Light Steam
5 Wool High Heat and
Medium Steam
6 Cotton and Linen High Heat and
High Steam
Icons
or
or
or
3-way Auto Shut-Off
The iron will automatically switch to Auto Shut-Off mode and stop heating
after being left inactive for 30 seconds on the soleplate or side, and 8
minutes on the heel rest. When the iron is in Auto Shut-Off mode, the red
light on the handle will blink. Simply move the iron to resume ironing and
the soleplate will automatically heat to selected temperature.
Vertical Steaming
Iron can be used without an ironing board as a garment steamer by holding
with soleplate in a vertical position. Remove wrinkles from curtains, drapes,
and use for small touch-ups on fabrics suitable for steaming.
1. Follow instructions 1-4 in “Using Your Iron” on page 5.
2. Hang garment on a hanger in a location that would not be impacted
by the steam, such as a bathroom shower rod.
3. With one hand, hold the garment tight from the base or side, being
careful to keep hands away from the steam. Hold preheated iron in
other hand.
4. Place soleplate about an inch away from the fabric and press the
Burst of Steam button. Allow a few seconds between burst to avoid
water dripping.
Tip: If water dripping occurs, the iron isn’t hot enough to create steam.
Simply allow the iron a minute to reheat and then resume steaming.
5. When finished steaming, turn the Steam Selector to the Off/
Dry Iron setting and set the temperature control dial to the
minimum temperature setting. Unplug from the outlet.
6. Stand iron on its heel rest and allow to completely cool
before storing.
CLEANING AND CARE
This product contains no user serviceable parts. Refer to qualified service
personnel.
AUTO-CLEAN
ADDITIONAL FEATURES
Burst of Steam
Generate extra steam momentarily by pressing the Burst of Steam button.
Use on fabrics suitable for steaming in either the vertical
or horizontal position. For best performance, allow several seconds
between bursts.
Spray Mist
Press the Spray Mist button to generate a light spray of water.
Spray Mist is used to dampen tough wrinkles while dry or steam ironing.
Do not spray silk.
6 7
• Use this feature to keep the iron free from build-up. For optimal results over
time, it is recommended that you clean your iron every 2-4 weeks. Homes
with harder water should clean their iron more often, every 1-2 weeks.
1. Fill the water tank well below the MAX fill line. Plug in the iron
2. Select the Wool fabric setting (number 5) on the temperature
3. Allow the iron to heat to desired temperature for about 2 minutes,
4. Hold iron over a sink with soleplate facing down. Press the Auto-
™
SYSTEM
control dial and stand the iron on its heel while it preheats.
then turn the dial to the MIN setting and unplug from the outlet.
Clean™ button. Be careful, as hot water and steam will come out of
the vents.
5. Continue to hold the button down until all of the water has emptied.
If necessary, slightly tilt the iron from side-to-side and front-to-back
to aid the process.
6. When finished, release the Auto-Clean™ button and place the iron
on its heel rest. Allow the iron to completely cool before storing.
CLEANING OUTSIDE SURFACES
1. Make sure the iron is unplugged and has completely cooled.
2. Wipe the soleplate and outer surface with a soft, damp cloth. Water
and small amounts of gentle household soaps, such as dishwashing
liquid, can be used. Never use heavy-duty cleaners, vinegar or
abrasive scouring pads that may scratch or discolor the iron.
3. After the iron has been thoroughly dried, turn the iron back on and
lightly steam over an old cloth. This will help remove any reside left
in the steam holes.
4. When finished cleaning, turn iron off and allow time to cool
before storing.
STORING YOUR IRON
1. Check that the iron is set to the minimum heat temperature setting and
Dry Iron steam setting,
2. Empty the water tank by opening the water fill door and turning the
iron upside down over a sink.
3. Wrap cord loosely around the heel of the iron.
4. Always store vertically on its heel to prevent water leaking from the
soleplate.
and completely cool.
• Whenever ironing a garment made with a mix of fabrics, select the
fabric setting based on the most delicate fabric.
• Whenever ironing fabric made of blended content, such as a shirt that
is 65% cotton and 35% polyester, use the “blends” setting (setting
number 2).
• Putting on clothes immediately after ironing can actually create
wrinkles. Always allow clothing to cool for about 5 minutes after
ironing to set the press.
• Did you know that this iron can be used like a garment steamer for
touch-ups? See the Vertical Steaming section for more details.
• Did you know that for proper maintenance and optimal performance
over time, this iron should be cleaned at least once a month? See the
Auto-Clean™ section for more details.
IRONING TIPS AND TRICKS
• The iron is designed to use ordinary tap water. A mix of 50% tap water
with 50% distilled water can be used In areas with very hard water to
reduce hard water build-up.
• If water dripping occurs, the iron isn’t hot enough to generate steam.
Allow the iron a minute to reheat and then resume ironing. Use the Dry
Iron steam setting when ironing at low temperatures.
• Allow the iron to stand from one to two minutes when changing the
temperature setting, whether to a higher or lower setting. This allows
time for heat up or cool down. Test garment by pressing a small hidden
area to make sure temperature of iron is correct.
• To prevent iron marks on fabric, iron the fabric inside out.
• For optimum performance, allow the iron to stand on the heel rest for
about two minutes after filling, prior to ironing.
• When unsure of fabric content, first test a small area (on the inside
seam or hem) before ironing entire garment or cloth.
8 9
Loading...