Black & Decker CS1004-RU User manual

ENRU

www.blackanddecker.ru

CS1004

ENGLISH

(Original instructions)

FIG. A

FIG. C

FIG. B

FIG. D

FIG. E FIG. GFIG. F

Surface of wood

(Original instructions)

Tip of tooth

ENGLISH

FIG. H

FIG. J

FIG. I

FIG. K

ENGLISH

(Original instructions)

Intended use

Your BLACK+DECKER™ CS1004 Circular Saw has been designed for sawing wood and wood products. This tool is intended for consumer use only.

Safety instructions

General power tool safety warnings

Warning: Read all safety warnings and all instructions. Failure to follow

the warnings and instructions listed below may result in electric shock, ﬁre and/or serious injury.

Save all warnings and instructions for future reference. The term "power tool" in

all of the warnings listed below refers to your mains operated (corded) power tool or battery operated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit.

Cluttered and dark areas invite accidents.

b. Do not operate power tools in explosive

atmospheres, such as in the presence of ﬂammable liquids, gases or dust. Power

tools create sparks which may ignite the dust or fumes.

c. Keep children and bystanders away

while operating a power tool.

Distractions can cause you to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet.

Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodiﬁed

plugs and matching outlets will reduce risk of electric shock.

b. Avoid body contact with earthed or

grounded surfaces such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your body is earthed or grounded.

c. Do not expose power tools to rain or

wet conditions. Water entering a power

tool will increase the risk of electric shock.

d. Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e. When operating a power tool outdoors,

use an extension cord suitable for outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp

location is unavoidable, use a residual current device (RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and

use common sense when operating a power tool. Do not use a power tool while you are tired or under the inﬂuence of drugs, alcohol or medication. A moment of inattention

while operating power tools may result in serious personal injury.

b. Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c. Prevent unintentional starting. Ensure

the switch is in the o-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your

ﬁnger on the switch or energising power tools that have the switch on invites accidents.

d. Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing

and balance at all times. This enables

better control of the power tool in unexpected situations.

(Original instructions)

ENGLISH

f. Dress properly. Do not wear loose

clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

g. If devices are provided for the

connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the

correct power tool for your application.

The correct power tool will do the job better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch

does not turn it on and o. Any power

tool that cannot be controlled with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power

source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach

of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e. Maintain power tools. Check for

misalignment or binding of moving parts, breakage of parts and any other condition that may aect the power tools operation. If damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

f. Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

g. Use the power tool, accessories and tool

bits etc. in accordance with these instructions, taking into account the

working conditions and the work to be performed. Use of the power tool for

operations dierent from those intended could result in a hazardous situation.

5. Service

a. Have your power tool serviced by a

qualiﬁed repair person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Additional power tool safety warnings

Warning! Additional safety warnings

for saws

a. Keep hands away from cutting area and

the blade. Keep your second hand on auxiliary handle, or motor housing. If

both hands are holding the saw, they cannot be cut by the blade.

b. Do not reach underneath the workpiece.

The guard cannot protect you from the blade below the workpiece.

c. Adjust the cutting depth to the thickness

of the workpiece. Less than a full tooth of

the blade teeth should be visible below the workpiece.

d. Never hold piece being cut in your hands

or across your leg. Secure the workpiece to a stable platform. It is important to

support the work properly to minimize body exposure, blade binding, or loss of control.

e. Hold power tool by insulated gripping

surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact

with a "live" wire will also make exposed metal parts of the power tool "live" and shock the operator.

f. When ripping always use a rip fence or

straight edge guide. This improves the

accuracy of cut and reduces the chance of blade binding.

g. Always use blades with correct size and

shape (diamond versus round) of arbour holes. Blades that do not match the

mounting hardware of the saw will run eccentrically, causing loss of control.

ENGLISH

(Original instructions)

h. Never use damaged or incorrect blade

washers or bolt. The blade washers and

bolt were specially designed for your saw, for optimum performance and safety of operation.

Further safety instructions for all saws

Causes and operator prevention of kickback:

• kickback is a sudden reaction to a

pinched, bound or misaligned saw blade, causing an uncontrolled saw to lift up and out of the workpiece toward the operator;

• when the blade is pinched or bound

tightly by the kerf closing down, the blade stalls and the motor reaction drives the unit rapidly back toward the operator;

• if the blade becomes twisted or

misaligned in the cut, the teeth at the back edge of the blade can dig into the top surface of the wood causing the blade to climb out of the kerf and jump back toward the operator.

Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below.

a. Maintain a ﬁrm grip with both hands on

the saw and position your arms to resist kickback forces. Position your body to either side of the blade, but not in line with the blade. Kickback could cause the

saw to jump backwards, but kickback forces can be controlled by the operator, if proper precautions are taken.

b. When the blade is binding, or when

interrupting a cut for any reason, release the trigger and hold the saw motionless in the material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blade is in motion or kickback may occur. Investigate and take corrective

actions to eliminate the cause of blade binding.

c. When restarting a saw in the workpiece,

centre the saw blade in the kerf and check that saw teeth are not engaged

into the material. If saw blade is binding,

it may walk up or kickback from the workpiece as the saw is restarted.

d. Support large panels to minimise the risk

of blade pinching and kickback. Large panels tend to sag under their own weight. Supports must be placed under

the panel on both sides, near the line of cut and near the edge of the panel.

e. Do not use dull or damaged blades.

Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and kickback.

f. Blade depth and bevel adjusting locking

levers must be tight and secure before making cut. If blade adjustment shifts

while cutting, it may cause binding and kickback.

g. Use extra caution when making a

"plunge cut" into existing walls or other blind areas. The protruding blade may

cut objects that can cause kickback.

Safety instructions for circular saws with outer or inner pendulum guards and with tow guard

a. Check lower guard for proper closing

before each use. Do not operate the saw if lower guard does not move freely and close instantly. Never clamp or tie the lower guard into the open position. If

saw is accidentally dropped, lower guard may be bent. Raise the lower guard with the retracting handle and make sure it moves freely and does not touch the blade or any other part, in all angles and depths of cut.

b. Check the operation of the lower guard

spring. If the guard and the spring are not operating properly, they must be serviced before use. Lower guard may

operate sluggishly due to damaged parts, gummy deposits, or a build-up of debris.

c. Lower guard should be retracted

manually only for special cuts such as "plunge cuts" and "compound cuts". Raise lower guard by retracting handle and as soon as blade enters the material, the lower guard must be released. For all

other sawing, the lower guard should operate automatically.

(Original instructions)

d. Always observe that the lower guard is

covering the blade before placing saw down on bench or ﬂoor. An unprotected,

coasting blade will cause the saw to walk backwards, cutting whatever is in its path. Be aware of the time it takes for the blade to stop after switch is released.

Residual risks

The following risks are inherent to the use of saws:

- Injuries caused by touching the rotating

parts.

Even with the application of the relevant safety regulations and the implementation of safety devices, certain residual risks cannot be avoided. These are:

- Impairment of hearing.

- Risk of accidents caused by the

uncovered parts of the rotating saw blade.

- Risk of injury when changing the blade.

- Risk of squeezing ﬁngers when opening

the guards.

- Health hazards caused by breathing dust

developed when sawing wood, especially oak, beech and MDF.

Saw blades

• Do not use blades of larger or smaller

diameter than recommended. For the proper blade rating refer to the technical data. Use only the blades speciﬁed in this manual, complying with EN 847-1.

• Warning! Never use abrasive wheels.

Safety of others

• This appliance is not intended for use by

persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure

that they do not play with the appliance.

Labels on tool

The label on your tool may include the following symbols

ENGLISH

Read Instructions Manual

Use Eye Protection

Use Ear Protection

V ........ Volts

A ........ Amperes

Hertz

W ........ Watts

min ..... minutes

..... Alternating

Current

..... Direct

Current

n0 ....... No-Load

Speed

...... Class II

Construction

.... Earthing

Terminal

.... Safety Alert

Symbol

.../min.. Revolutions

or Reciprocation per minute

Hz .......

List of Content

1 Circular saw

1 18-Teeth blade with carbide tungsten tips

1 Rip fence

Position of date barcode

The Date Code, which also includes the year of manufacture, is printed into the housing. Example:

2017 XX JN

Year of manufacturing

Electrical safety

This tool is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate.

• If the supply cord is damaged, it must be

replaced by the manufacturer or an authorised BLACK+DECKER Service Centre in order to avoid a hazard.

Features (Pg. 2)

1. On/o switch

2. Main handle

3. Secondary handle

4. Shoe

5. Saw blade

6. Saw blade lower guard

7. Lower guard retracting lever

8. Bevel adjustment knob

9. Outer blade clamp washer

10. Blade retaining bolt

11. Depth adjustment lever

ENGLISH

(Original instructions)

12. Depth scale

13. Bevel angle scale

14. Saw blade hex wrench

15. Spindle lock button

Assembly/Adjustment set-up

Warning: Always unplug saw from power

supply before any of the following operations.

Adjusting the depth of cut (Fig. E and F)

The depth of cut should be set according to the thickness of the workpiece.

• Loosen the lever (11) to unlock the saw

shoe.

• Move the saw shoe (4) into the desired

position (Fig. E). The corresponding depth of cut can be read from the scale

(12).

• Tighten the lever to lock the saw shoe in

place.

• Set depth adjustment of saw such that

one tooth of the blade projects below

the workpiece as shown in (Fig. F).

Adjusting the bevel angle (Fig. G)

This tool can be set to bevel angles between 0° and 45°

• Loosen the locking knob (8) to unlock

the saw shoe.

• Move the saw shoe (4) into the desired

position (Fig. G). The corresponding bevel angle can be read from the scale

(13).

• Tighten the locking knob to lock the saw

shoe in place.

Installing the blade (Fig. H)

• Keep the spindle lock button (15)

depressed and rotate the blade until the spindle lock engages.

• Loosen and remove the blade retaining

screw (10) by turning the hex wrench (14) counterclockwise (Fig. H).

• Remove the outer washer (9).

• Place the saw blade (5) onto the spindle

shaft, making sure that the arrow on the blade points in the same direction as the arrow on the upper gaurd of the tool.

• Fit the outer washer on the spindle with

the larger ﬂat surface against the blade.

• Insert the blade retaining screw into the

hole in the spindle.

• Securely tighten the blade retaining

screw by turning hex wrench clockwise to tighten the blade retaining screw.

Removing the blade

• Loosen and remove the blade retaining

screw (10) by turning it counterclockwise using the hex wrench (14).

• Remove the outer washer (9).

• Remove the saw blade (5).

Notice: To reduce the risk of serious

personal injury, read, understand and follow

all important safety warnings and instructions prior to using tool.

Warning: To reduce the risk of serious

personal injury, read, understand and follow

all important safety warnings and instructions prior to using tool.

General Cuts

(Important: read safety warnings and instructions.)

Guard against kickback

With unit unplugged, follow all assembly,

adjustment and set up instructions. Make

sure lower guard operates. Select the proper blade for the material to be cut.

• Measure and mark work for cutting.

• Support and secure work properly (See Safety Rules and Instructions).

• Use appropriate and required safety equipment (See Safety Rules).

• Secure and maintain work area (See Safety Rules).

+ 16 hidden pages