Black & Decker CRT129 Instruction Manual
GENERAL SAFETY RULES - FOR ALL BATTERY OPERATED TOOLS
WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to follow all instructions
listed below, may result in electric shock, fire and/or serious personal injury
SAVE THESE INSTRUCTIONS
WORK AREA
• Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases,
or dust. Power tools create sparks which may ignite the dust or fumes.
• Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to
lose control.
ELECTRICAL SAFETY
• Do not abuse the cord. Never use the cord to carry the tool. Keep cord away from heat, oil, sharp edges or
moving parts. Replace damaged cords immediately. Damaged cords may create a fire.
•A battery operated tool with integral batteries or a separate battery pack must be recharged only with the
specified charger for the battery. A charger that may be suitable for one type of battery may create a risk of
fire when used with another battery.
• Use battery operated tool only with specifically designated battery pack. Use of any other batteries may
create a risk of fire.
PERSONAL SAFETY
• Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool
while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating
power tools may result in serious personal injury,
• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing , and
gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
•Avoid accidental starting. Be sure switch is in the locked or off position before inserting battery pack.
Carrying tools with your finger on the switch or inserting the battery pack into a tool with the switch on invites
accidents.
• Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enable better
control of the tool in unexpected situations.
• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
TOOL USE AND CARE
• Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the
work by hand or against your body is unstable and may lead to loss of control.
• Do not force tool. Use the correct tool for your application. The correct tool will do the job better and safer at
the rate for which it is designed.
• Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with the switch is
dangerous and must be repaired.
• Disconnect battery pack from tool or place the switch in the locked or off position before making any
adjustments, changing accessories, or storing the tool. Such preventative safety measures reduce the risk of
starting the tool accidentally.
• Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of
untrained users.
• When battery pack is not in use, keep it away from other metal objects like: paper clips, coins, keys, nails,
screws or other small metal objects that can make a connection from one terminal to another. Shorting the
battery terminals together may cause sparks, burns, or a fire.
• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp cutting
edge are less likely to bind and are easier to control.
• Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may
affect the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by
poorly maintained tools.
• Use only accessories that are recommended by the manufacturer for your model. Accessories that may be
suitable for one tool may create a risk of injury when used on another tool.
SERVICE
•Tool service must be performed only by qualified repair personnel. Service or maintenance performed by
unqualified personnel may result in a risk of injury.
• When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or failure to follow Maintenance Instructions may create a
risk of shock or injury.
SPECIFIC SAFETY RULES
• Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a "live" wire will also make exposed metal parts of the
tool "live" and shock the operator.
CAUTION Use of this tool can generate dust containing chemicals known to cause cancer, birth defects or
other reproductive harm. Use appropriate respiratory protection.
CAUTION: Some wood contains preservatives such as copper chromium arsenate (CCA) which can be
toxic. When cutting these materials extra care should be taken to avoid inhalation and minimize skin
contact.
The label on your tool may include the following symbols.
V ..............................volts A ............................amperes
Hz ............................hertz W ..........................watts
min ..........................minutes ........................alternating current
........................direct current
n
o ..........................no load speed
............................
Class II Construction
..........................earthing terminal
..........................safety alert symbol .../min ....................revolutions or
reciprocations
per minute
Safety Warnings and Instructions: Charging the Drill
1. This manual contains important safety and operating instructions.
2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2)
battery, and (3) product using battery.
3. CAUTION: To reduce the risk of injury, charge only Black & Decker Power Packs. Other types of bat-
teries may burst causing personal injury and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold by Black & Decker may result in a risk of fire, electric
shock, or injury to persons.
6. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting
charger.
7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to dam-
age or stress.
8. An extension cord should not be used unless absolutely necessary. Use of improper extension cord could
result in a risk of fire, electric shock or electrocution.
a. Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round jacketed extension
cords should be used, and we recommend that they be listed by Underwriters Laboratories (U.L.). If the
extension is to be used outside, the cord must be suitable for outdoor use. Any cord marked for outdoor
use can also be used for indoor work. The letters "W" or "WA" on the cord jacket indicate that the cord
is suitable for outdoor use.
b. An extension cord must have adequate wire size (AWG or American Wire Gauge) for safety, and to
prevent loss of power and overheating. The smaller the gauge number of the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity than 18 gauge. When using more than one extension to make up the total length, be sure each extension contains at least the minimum wire size.
CHART FOR MINIMUM WIRE SIZE (AWG)OF EXTENSION CORDS
NAMEPLATE RATING AMPS – 0 – 10.0
Total Extension Cord Length (ft) 25 50 75 100 125 150
Wire Gauge 18 18 16 16 14 14
9. Use only the supplied charger when charging your drill. The use of any other charger could damage
the drill or create a hazardous condition.
10. Use only one charger when charging.
11. Do not attempt to open the charger or the drill. There are no customer serviceable parts inside. Return
to any authorized Black & Decker service center.
12. DO NOT incinerate the drill or battery packs even if they are severely damaged or completely worn out.
The batteries can explode in a fire.
13. Do not incinerate the batteries. They can explode in a fire. A small leakage of liquid from the battery
cells may occur under extreme usage, charging or temperature conditions. This does not indicate a fail-
ure. However, if the outer seal is broken and this leakage gets on your skin:
a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon juice or vinegar.
c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10 minutes and seek
immediate medical attention. MEDICAL NOTE: The liquid is a 25-35% solution of potassium hydroxide.
Charging the Power Pack
THE BATTERIES IN YOUR POWER PACK ARE NOT FULLY CHARGED AT THE FACTORY. BEFORE
ATTEMPTING TO CHARGE THEM, THOROUGHLY READ ALL OF THE SAFETY INSTRUCTIONS.
The 3 hour charger is designed to use standard household 120 volt 60 Hz power.
1. Put the switch control lever in the center OFF position (Fig. 1) and remove power pack from the tool.
2. Plug the charger into any standard 120 Volts 60 Hz electrical outlet.
3. Insert the power pack into the charger and let it charge for 3 hours.
4. Remove pack from the charger and replace in tool.
Important Charging Notes
1. After normal usage, your power pack should be fully charged in 3 hours or less. If the power pack is
run-down completely, it may take up to 6 hours to become fully charged. Your power pack was sent
from the factory in an uncharged condition. Before attempting to use it, it must be charged for at least
3 hours.
2. DO NOT charge the power pack in an air temperature below 40°F or above 105°F. This is important
and will prevent serious damage to the power pack. Longest life and best performance can be obtained
if the power pack is charged when the air temperature is about 75°F.
3. While charging, the charger may hum and become warm to touch. This is a normal condition and does
not indicate a problem.
4. If the power pack does not charge properly—(1) Check current at receptacle by plugging in a lamp or
other appliance. (2) Check to see if receptacle is connected to a light switch which turns power off when
you turn out the lights. (3) Move charger and power pack to a surrounding air temperature of 40°F to
105°F. (4) If the receptacle and temperature are OK, and you do not get proper charging, take or send
the power pack and charger to your local Black & Decker service center. See "Tools Electric" in yellow
pages.
5. The power pack should be recharged when it fails to produce sufficient power on jobs which were eas-
ily done previously. DO NOT CONTINUE using drill with its power pack in a depleted condition.
6. To prolong power pack life, avoid leaving the power pack on charge for more than 8 hours. Although
overcharging is not a safety concern, it can significantly reduce overall power pack life.
7. When the battery is inserted into the charger, the red “Charging Indicator” light will come on indicating
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL
PRODUCTO.
INSTRUCTION MANUAL
Catalog Number CRT129
11112222VVVVOOOOLLLLTTTT 3333////8888"""" CCCCOOOORRRRDDDDLLLLEEEESSSSSSSS DDDDRRRRIIIILLLLLL
LL
KEY INFORMATION YOU SHOULD KNOW:
•Battery pack must be charged for three hours before initial use.
•Charger may hum; batteries or charger may become warm during charging.
1
Depress for reverse (this side)
Enfoncer pour la marche arrière (du côté gauche)
Oprima para reversa (desde el lado izquierdo)
Cat. No. CRT129 Form No. 396714-00 (MAY00) Copyright©2000 Black & Decker Pri nted in China
Torque Adjust Collar
collier de réglage du couple
collarÍn de ajuste de par (torque)
Gear Shifter
Sélecteur de vitesses
Palanca de cambio de engranes
Depress for forward (other side)
Enfoncer pour la marche avant (du côté droit)
Oprima para marcha hacia adelante (desde el lado derecho)
Center “OFF” position
Position «ARRÊT» centrale
Posición central “APAGADO”
2
that there is contact between the battery and charger. The light will stay on as long as the battery is in the
charger and the charger is plugged into a working outlet. It WILL NOT flash, go out or change to a
different color when the charging cycle is complete.
Safety Warnings and Instructions: Drills
1. Do not lock the tool ON when drilling by hand. Refer to Operating Instructions-Switch.
2. Hold drill firmly to control the twisting action of the drill. See figure 2.
3. When attaching accessories in the drill chuck, hand tighten the keyless chuck firmly
4. Drill may stall (if overloaded or improperly used) causing a twist. Always expect the stall.Grip the drill
firmly to control the twisting action (see Fig.2) and prevent loss of control which could cause personal
injury. If a stall does occur, release the trigger immediately and determine the reason for the stall before
re-starting.
Operating Instructions
Switch and Control Button
A forward/reverse control button determines the direction of the tool and also serves as a lock off button (Fig.
1). To select forward rotation, release the trigger switch and depress the forward/reverse control button as
shown in Figure 1. To select reverse, depress the forward/reverse control button the opposite direction. The
center position of the control button locks the tool in the off position. When changing the position of the control
button, be sure the trigger is released. NOTE: The first time tool is run after changing direction of rotation, you
may hear a click on start up. This is normal and does not indicate a problem.
To rque Control
To set the tool’s torque, rotate the adjustable torque collar clockwise as required. 24 positions are marked
around the collar and the higher the number, the higher the torque. Each click in a clockwise direction means
an increase in the torque produced. Position 24 is the drill mode and is marked with the picture of a drill bit.
In this position the clutch will not operate. This permits heavy duty drilling / driving screws.
Warning: To control twisting action, place both hands on drill as shown in Fig. 2.
Dual Range Gearing
The dual range feature of your Drill allows you to shift gears for greater versatility. To select low speed, high
torque setting (position 1), turn tool off and permit to stop. Push button forward towards the chuck. To select
the high speed, low torque setting (position 2), turn tool off and permit to stop. Slide gear shifter back (away
from chuck). NOTE: Do not change gears when tool is running. If you are having trouble changing gears,
make sure that the dual range gear button is either completely pushed forward or completely pushed back.
Keyless Chuck Operation
To attach accessories, grasp the rear half of the chuck with one hand and use your other hand to rotate the
front half in the counterclockwise direction. Insert the bit or other accessory fully into the chuck, and tighten
securely by holding the rear half of the chuck and rotating the front portion in the clockwise direction as
viewed from the chuck end.
Drilling
• Use sharp drill bits only.
• Support and secure work properly, as instructed in the Safety Instructions.
• Use appropriate and required safety equipment, as instructed in the safety instructions.
• Secure and maintain work area, as instructed in the safety instructions.
• Run the drill very slowly, using light pressure, until the hole is started enough to keep the drill bit from
slipping out of it.
• Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting but not so much
as to stall the motor or deflect the bit.
• Hold the drill firmly to control its twisting action.
• DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT TO START IT. DAMAGE TO THE DRILL CAN RESULT.
• Minimize stalling on breakthrough by reducing pressure and slowly drilling through last part of hole.
• Keep the motor running while pulling the bit out of a drilled hole This will help reduce jamming.
• Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which should be
drilled dry. Lubricants that work best are sulphurized cutting oil or lard oil.
• When using twist drill bits to drill holes in wood, it will be necessary to pull the bits out frequently to clear
chips from the flutes.
• Make sure switch turns drill on and off.
WARNING:It is important to support work properly and to hold the drill firmly to prevent loss of control
which could cause personal injury If you have questions on how to operate tool, call: 1-800-54-HOW-TO
Maintenance
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse
any part of the tool into a liquid. IMPORTANT: To assure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment should be performed by authorized service centers or other qualified service
organizations, always using identical replacement parts.
The RBRC™ Seal
The RBRC™ (Rechargeable Battery Recycling Corporation)Seal on the nickel-cadmium battery (or
battery pack) indicates that the costs to recycle the battery (or battery pack) at the end of its useful
life have already been paid by Black & Decker. In some areas, it is illegal to place spent nickelcadmium batteries in the trash or municipal solid waste stream and the RBRC program provides an
environmentally conscious alternative.
RBRC in cooperation with Black & Decker and other battery users, has established programs in the United
States and Canada to facilitate the collection of spent nickel-cadmium batteries. Help protect our environment
and conserve natural resources by returning the spent nickel-cadmium battery to an authorized Black &
Decker service center or to your local retailer for recycling. You may also contact your local recycling center
for information on where to drop off the spent battery, or call 1-800-8-BATTERY.
Accessories
Recommended accessories for use with your tool are available from your local dealer or authorized service
center. If you need assistance regarding accessories, please call: 1-800-54-HOW-TO. The following
accessories should be used only in the sizes specified below: BITS, METAL DRILLING – Up to 3/8" (9.5mm);
BITS, MASONRY DRILLING – Up to 3/8" (9.5mm); WOOD DRILLING – Up to 1/2" (12.7mm).
WARNING: The use of any accessory not recommended for use with this tool could be hazardous.
Full Two-Year Home Use Warranty
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship.
The defective product will be replaced or repaired at no charge in either of two ways. The first, which will
result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the
store is a participating retailer). Returns should be made within the time period of the retailer’s policy for
exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the
retailer for their specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service
Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned
and authorized service centers are listed under "Tools-Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have
other rights which vary from state to state. Should you have any questions, contact the manager of your
nearest Black & Decker Service Center. This product is not intended for commercial use.
IMPORTANTES MESURES DE SÉCURITÉ - POUR TOUS LES OUTILS ALIMENTÉS
PAR PILES
AVERTISSEMENT! Lire et comprendre toutes les directives. Le non-respect de toutes les directives
suivantes présente des risques de secousses électriques, d’incendie ou de blessures graves.
CONSERVER CES MESURES.
ZONE DE TRAVAIL
• S’assurer que la zone de travail est propre et bien éclairée. Des établis encombrés et des
endroits sombres présentent des risques d’accidents.
• Ne pas utiliser des outils électriques en présence de vapeurs explosives (comme celles
dégagées par des liquides, des gaz ou des poussières inflammables). Les étincelles générées
par le moteur des outils électriques peuvent enflammer les poussières ou les vapeurs.
• Éloigner les curieux, les enfants et les visiteurs de la zone de travail lorsqu’on utilise un outil
électrique. Une distraction peut entraîner la perte de maîtrise de l’outil.
MESURES DE SÉCURITÉ RELATIVES À L’ÉLECTRICITÉ
• Manipuler le cordon avec soin. Ne jamais se servir du cordon afin de transporter l’outil .
Éloigner le cordon des sources de chaleur, des flaques d’huile, des arêtes tranchantes et des
pièces mobiles. Remplacer immédiatement les cordons endommagés. Les cordons
endommagés augmentent les risques de secousses électriques.
• Il faut charger un outil à piles intégrées ou un ensemble de piles seulement dans le chargeur
conçu à cet effet. Un chargeur convenant pour un type de piles peut présenter un risque
d’incendie lorsqu’on s’en sert avec un autre type de piles.
• Utiliser un outil alimenté par piles seulement avec la pile appropriée. L’utilisation de toute autre
pile présente des risques d’incendie.
SÉCURITÉ PERSONNELLE
• Demeurer vigilant, prendre soin et faire preuve de jugement lorsqu’on utilise un outil
électrique. Ne pas s’en servir lorsqu’on est fatigué ou affaibli par des drogues, de l’alcool ou
des médicaments. De graves blessures peuvent résulter d’un moment d’inattention lors de
l’utilisation d’un outil électrique.
• Porter des vêtements appropriés. Éviter de porter des vêtements amples ou des bijoux.
Recouvrir la chevelure si elle est longue. Éloigner les cheveux, les vêtements et les gants des
pièces en mouvement qui peuvent les happer.
• Éviter les démarrages accidentels. S’assurer que l’interrupteur est en position hors tension ou
verrouilleé avant d’insérer la pile. Afin d’éviter les risques de blessures, ne pas transporter l’outil
avec le doigt sur l’interrupteur ni insérer la pile dans un outil dont l’interrupteur est en position
sous tension.
• Enlever les clés de réglage avant de mettre l’outil sous tension. Une clé qui est laissée sur une
pièce rotative de l’outil présente des risques de blessures.
• Ne pas dépasser sa portée. Garder son équilibre en tout temps. On s’assure d’une meilleure
maîtrise de l’outil dans des situations imprévues grâce à une position stable et un bon équilibre.
• Porter de l’équipement de sécurité. Toujours porter des lunettes de sécurité. Dans certaines
conditions, il faut porter des masques respiratoires, des chaussures antidérapantes, un casque de
sécurité ou des protège-tympans.
UTILISATION ET ENTRETIEN DE L’OUTIL
• Utiliser des pinces de serrage ou de tout autre moyen pratique afin de fixer et de soutenir la
pièce à ouvrer sur une plate-forme stable. La pièce est instable lorsqu’elle est retenue par la
main ou le corps de l’utilisateur. Cela présente des risques de perte de maîtrise de l’outil.
• Ne pas forcer l’outil. Utiliser l’outil approprié à la tâche. L’outil approprié fonctionne mieux et
sûrement lorsqu’on s’en sert à son rendement nominal.
• Ne pas se servir de l’outil lorsque l’interrupteur est défectueux. Le cas échéant, l’outil est
dangereux et il faut le réparer.
• Enlever la pile de l’outil ou placer celui-ci en position hors tension ou verrouillée avant de le
régler, d’en remplacer les accessoires ou de le ranger. On minimise de la sorte le risque de
démarrage accidentel de l’outil.
• Ranger l’outil hors de portée des enfants et de toute autre personne qui n’en connaît pas le
fonctionnement. L’outil est dangereux entre les mains de ces personnes.
• Lorsque la pile ne sert pas, l’éloigner de tout objet métallique (comme des trombones, des
pièces de monnaie, des clés, des clous, des vis ou tout autre petit objet métallique qui peut
créer une connexion d’une borne à l’autre). Lorsque les bornes sont court-circuitées, cela peut
générer des étincelles, des brûlures ou un incendie.
• Prendre soin des outils. S’assurer que les outils de coupe sont tranchants et propres. Des outils
bien entretenus à arêtes tranchantes ont moins tendance à se coincer et ils se maîtrisent mieux.
• Vérifier l’alignement et les attaches des pièces mobiles, le degré d’usure des pièces ainsi que
tout autre facteur susceptible de nuire au bon fonctionnement de l’outil. Faire réparer un outil
endommagé avant de s’en servir. Des outils mal entretenus sont la cause de nombreux
accidents.
• Utiliser seulement les accessoires recommandés par le fabricant. Des accessoires qui
conviennent à un outil peuvent présenter des risques avec un autre outil.
ENTRETIEN
• Confier l’entretien de l’outil seulement à du personnel qualifié. Le non-respect de la présente
directive présente des risques de blessures.
• Lors de l’entretien de l’outil, utiliser seulement des pièces de rechange identiques. Respecter
les consignes relatives à l’entretien du présent guide d’utilisation. Il y a risque de secousses
PPPPeeeerrrrcccceeeeuuuusssseeeessss ssssaaaannnnssss ffffiiiillll ddddeeee
11112222 VVVV 11110000mmmmmmmm ((((3333////8888ppppoooo))))
AVANT DE RETOURNER LE PRODUIT, PEU IMPORTE LARAI-
SON PRIÈRE DE COMPOSER
1 800 544-6986
GUIDE D’UTILISATION
Modèle CRT129
RENSEIGNEMENTS IMPORTANTS
•Il faut charger l’ensemble de piles pendant trois heures avant de s’en servir.
•Le chargeur peut émettre un bourdonnement; les piles ou le chargeur peuvent
devenir chauds au toucher pendant le chargement.
CONSERVER LE PRÉSENT GUIDE À TITRE DE RÉFÉRENCE.
See ‘Tools-Electric’
– Yellow Pages –
for Service & Sales
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
Loading...