Bissell 1846 User Manual

PROHEAT®
ADVANCED

Deep Cleaner

_______________

USER GUIDE

1846 SERIES

More of a video
person? Look for this
icon and go online
for an instructional
how-to video at

www.BISSELL.com

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING YOUR DEEP CLEANER.

When using an electrical appliance, basic precautions should be observed, including the following:

WARNING

TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, OR INJURY:

» Connect to a properly grounded

outlet only. See grounding
instructions. Do not modify the
3-prong grounded plug.

» Do not leave appliance when it is

plugged in. Unplug from outlet when

not in use and before servicing.
» Use indoors only.
» Do not allow to be used as a toy.

Close attention is necessary when

used by or near children.
» Do not use for any purpose other

than described in this User’s

Guide. Use only manufacturer’s

recommended attachments.
» Do not use with damaged cord

or plug. If appliance is not

working as it should, or has been

dropped, damaged, left outdoors,

or dropped into water, have it

repaired at an authorized

service center.
» Do not operate the appliance

unless the belt door is securely

assembled in the location

provided.

» Do not pull or carry by cord, use

cord as a handle, close a door on
cord, or pull cord around sharp
edges or corners. Do not run
appliance over cord. Keep cord
away from heated surfaces.

» Do not unplug by pulling on

cord. To unplug, grasp the plug,
not the cord.

» Do not handle plug or appliance

with wet hands.

» Do not put any object into open

ings. Do not use with any opening
blocked; keep openings free of
dust, lint, hair, and anything that
may reduce air flow.

» Keep hair, loose clothing, fingers,

and all parts of body away from
openings and moving parts.

» Turn off all controls before plug

ging or unplugging appliance.

» Use extra care when cleaning

on stairs.

» Do not use to pick up flammable

or combustible materials (lighter
fluid, gasoline, kerosene, etc.)
or use in areas where they may
be present.

» Do not use appliance in an

enclosed space filled with vapors
given off by oil base paint, paint

thinner, some moth proofing
substances, flammable dust,
or other explosive or toxic vapors.

» Do not use to pick up toxic

material (chlorine bleach,
ammonia, drain cleaner, etc.).

» Do not pick up anything that

is burning or smoking, such as cig­arettes, matches, or hot ashes.

» Use only BISSELL cleaning

products intended for use

-

with this appliance to prevent
internal component damage.
See the Cleaning Formula section
of this guide.

» Do not immerse. Use only on

surfaces moistened by the
cleaning process.

» Keep appliance on a level surface.

-

» Do not carry the appliance while

in use.

» Always install float before any

wet pick-up operation.

» Unplug before connecting

TurboBrush® Tool.

SAVE THESE INSTRUCTIONS
FOR FUTURE USE

This model is for household use only. Commercial use of this unit voids the manufacturer’s warranty.

WARNING

Improper connection of the equipment-grounding

conductor can result in a risk of electrical shock. Check

with a qualified electrician or service person if you

aren’t sure if the outlet is properly grounded. DO NOT

MODIFY THE PLUG. If it will not fit the outlet, have a

proper outlet installed by a qualified electrician. This

appliance is designed for use on a nominal 120-volt

circuit, and has a grounding attachment plug that

looks like the plug in the illustration. Make certain

that the appliance is connected to an outlet having

the same configuration as the plug. No plug adapter

should be used with this appliance.

www.BISSELL.com

2

GROUNDING INSTRUCTIONS

This appliance must be connected to a grounded
wiring system. If it should malfunction or break down,
grounding provides a safe path of least resistance for
electrical current, reducing the risk of electrical shock.
The cord for this appliance has an
equipment-grounding conductor
and a grounding plug. It must
only be plugged into an outlet
that is properly installed and
grounded in accordance with
all local codes and ordinances.

Grounded
Outlet

Grounding Pin

Thanks for buying a BISSELL carpet cleaner!

BISSELL

We love to clean and we’re excited to share one of our innovative products
with you. This guide has important instructions on how your new carpet
cleaner works, including using (pages 8-12), maintaining (page 13), and if
there is a problem, troubleshooting (page 14).

In just a few simple assembly steps, you’ll be ready to deep clean. Flip to
page 6 and let’s get started!

What’s In The Box?

1. 2. 3.

4. 5. 6.

7.

8.

Safety Instructions...........2

Product View................4

1. Upper Handle

2. Base

3. 3” Tough Stain Tool

4. Upper Hose Wrap

5. Lower Hose Wrap

6. Long Screws (2)
(taped to Upper Handle)

7. Short Screws (2)
(taped to Upper Handle)

8. Nozzle Clean Out Tool

9. Trial-Size BISSELL Formula

NOTE: Not all accessories

come with every model. Be
sure to check the carton for

9.

additional tools.

Troubleshooting ............14

Warranty ...................15

Cleaning Formulas...........5

Assembly ...................6

Operations ...............9-12

Maintenance & Care ......12-13

Service .....................15

Contact Information ........15

Product Registration........16

Parts & Supplies ............16

www.BISSELL.com

3

Getting to Know Your Deep Cleaner

8

6

1

2

3

4

5

14

7

9

11

10

12

13

15

www.BISSELL.com

4

1 Tough Stain Tool
2 ReadyTools™ Dial
3 Belt Access Door
4 6 Rows DirtLifter® PowerBrush
(under nozzle)
5 Floor Nozzle
6 Spray Trigger
7 Cord Clip

8 Upper Handle
9 Quick Release™ Hose Wrap
10 Ready-to-Use Hose
11 Extra Long Power Cord
12 Lower Hose Wrap
13 2-in-1 Tank
14 Recline Pedal
15 Power Switch

*Tools included may vary

Cleaning Formulas

WARNING

WARNING: To reduce the risk of fire and electric shock when cleaning a hard floor, the

BISSELL bare floor tool (2035641) must be used and is only to be used with BISSELL Hard

Floor Solutions formula intended for use with this appliance. To reduce the risk of electric

shock due to internal component damage, use only BISSELL cleaning formulas intended for

use with the deep cleaner.

Keep plenty of genuine BISSELL 2X*
formula on hand so you can clean and
protect whenever it fits your schedule.

Revives
carpets

to look

their best

Pet Stain &

Odor

Removes
tough pet
stains and

contains

patented

odor removal

technology

Includes

Scotchgard™

Protector

BOOST

Repels stains

from soaking

into carpet

fibers

Removes

pet stains

and odors

permanently

2X* CLEANING FORMULA

DeepClean

& Protect

Deep cleans

carpets

and protects

from future

stains with

Scotchgard™

Protector

Helps remove

pet & pollen

CARPET CLEANING FORMULA ENHANCER

Oxy Boost Renew Boost Prevent Boost

Removes old,

set-in stains

permanently

PROFESSIONAL

FORMULA

Professional

Deep

Cleaning

Out cleans

all other

formulas

Includes

Scotchgard™

Protector

Pet Oxy

Boost

Allergen

Cleansing

allergens

Always use genuine BISSELL deep
cleaning formulas. Non-BISSELL cleaning
solutions may harm the machine and will
void the warranty.

PRE TREAT SPOTS AND STAINS TO IMPROVE

CARPET CLEANING PERFORMANCE

Stain PreTreat Pet Stain PreTreat

Pretreat to

penetrate

and loosen

tough stains

DeepClean

+ Refresh

Powerful

cleaning

with a

refreshing

scent

PRETREAT

Pretreat to help

remove tough

Deep Clean

+ Oxy

Removes

deep down

dirt, pet
stains, &

pet odor

pet stains

and odors

BARE FLOOR

FORMULAS

Hard Floor

Solutions

Safe use for

linoleum,
vinyl, and

tile; removes

dirt and grime

ceramic

tough

Pet PreTreat +

Sanitize

Penetrates to

sanitize and loosen

tough stains

ONLY BISSELL Protects from future stains with Scotchgard™ Protector.
Scotchgard™ is a trademark of 3M®.
*2.5 fl. oz. of 2X concentrated formula is equivalent to 5.0 fl. oz. of non-concentrated formula.

www.BISSELL.com

5

Assembly

WARNING

Do not plug in your deep cleaner until you are familiar with all instructions
and operating procedures.

Your deep cleaner comes in four
easy-to-assemble components and
an accessory bag.

- Upper Handle

- Base

- Upper Hose Wrap

- Lower Hose Wrap

1

2

1

Slide handle assembly onto lower body

and secure with two long screws.

3

The only tool you will need to assemble
your deep cleaner is a Phillips screwdriver.

2

Attach upper hose rack to back of upper
handle by pushing into open slots and
sliding down until it snaps into place.

4

1

Attach lower hose rack by sliding it in place on the lower
body assembly and securing it with 2 short screws.

Attach Tough Stain tool to end of hose.

www.BISSELL.com

6

3

2

Wrap flex hose around
hose rack and secure
it into notched out
holder as shown.

Special Features

2-in-1 Tank ™

1

Our 2-in-1 Tank™ system is designed with a heavy
duty bladder inside for clean water. As you clean, the
clean water in the bladder will empty and mix with the
cleaning formula. Dirty water will be pulled out of your
carpets and collect around the outside of the bladder
so that clean and dirty water are always kept separate.
This allows you to maximize tank space, yet only carry
one tank to and from the sink for filling and emptying.

2

Measuring Cup

Your deep cleaner is equipped with a measuring cup
for adding the proper amount of formula to the 2-in-1
tank. For convenience, the measuring cup is built into
the lid.

Removable Nozzle

3

Cleaning your machine after you’re done has never
been easier! This nozzle pops o for rinsing in the
sink. Use the Nozzle Clean Out Tool also! Slide the tool
into the slot that touches the floor. Work the tool to
remove debris that may be caught in the nozzle.

Before You Clean

Maximize Results with your ProHeat Deep Cleaner...

• Plan activities to give your carpet time to dry.

• Move furniture to another area if cleaning an entire room (optional).

• Thoroughly vacuum area with a dry vacuum cleaner before deep cleaning.

• Plan your cleaning route to leave an exit path. It is best to begin cleaning in
the corner farthest from your exit.

• Pretreat
Pretreating your carpet is recommended to improve cleaning eectiveness
for heavily soiled carpet in high trac areas such as entryways and hallways.
a. Spray the BISSELL Stain PreTreat formula onto heavy trac areas,
soiled areas, or stains.
b. Allow to penetrate for at least 3 minutes.
c. Use the ProHeat machine on the high trac setting.

www.BISSELL.com

7

Before You Clean: Prepare Your Machine

Fill the 2-in-1 Tank with Water

1

2

1

3

5

4

6

2

3-Fill with BISSELL 2X formula to the indi­cated fill line on the built in measuring cup
and pour it into the bladder.

4-Fill the bladder with clean hot tap water
(140F/60C MAX). *Do not boil or microwave
the water as it can destroy the bladder.

**If you are using BISSELL Boost formulas,
measure out the formula by the bottle’s
instructions and add it to the bladder at this
time.

5-Return the tank lid by matching it to the
tank edges. The tank handle must be in the
forward position in order to set the lid in
place. Rotate the handle to secure the latch.

Note: Remember to secure the lid before
picking up the tank.

6-Seat the tank firmly back into the machine

base. Rotate the tank handle back into
latched position.

1-Press the recline pedal to access
the 2-in-1 tank. Remove the tank
from the base of the machine by
lifting the tank carry handle.

2-Carry the tank like a bucket to
the sink. Rotate the carry han­dle forward to unlatch the lid.
Remove the lid and turn it over to
locate the measuring cup.

NOTE: Heatwave Technology™
helps maintain the temperature
of the water in your 2-in-1 tank
while you’re cleaning.

www.BISSELL.com

8

Operations: Carpet Cleaning

TIP: Thorough vacuuming before deep cleaning will prevent early clogging in the

nozzle and lint trap.

1

Plug the power cord into a
properly grounded outlet.

2

Set the ReadyTools Dial to
“FLOOR CLEANING”.

4

Recline the machine by pressing the
gray release switch with your foot.

5

3

Turn the power on by
pressing the red Power
Switch on the back of the
machine with your foot.

NOTE: Do not overwet the carpet. Also
take care not to run over loose objects,
edges of area rugs, or the power cord.

NOTE: Stalling the brush by running over
loose objects, edges of area rugs, or the
power cord may cause the belts to snap
and break.

While pressing the trigger, make one slow pass
forward and back to put water and formula down.

Release the trigger and make one slow pass
forward and back over the same area to pick up
the water and formula that was just put down.

Repeat until the liquid coming up appears clean.
Continue passes without pressing the trigger until
you can’t see any more water being suctioned up.

ATTENTION: To prevent damage to Berber carpets, avoid repeated strokes in
the same area.

NOTE: You may notice hair and debris deposits on the carpet or in the tank that were
loosened by the cleaning action (especially with newer carpets that may have never been
deep cleaned before). This debris should be picked up and thrown away.

www.BISSELL.com

9

Operations: Upholstery & Spot Cleaning

IMPORTANT: Check upholstery tags for any special care instructions. If possible,

check for colored stung as it is possible the color could bleed through. Check for
colorfastness in a hidden area - like the back or underside of the furniture.

Vacuum thoroughly to
pick up dirt and debris.
Use a vacuum with a
hose and tool for fabric
folds and stair crevices.

4

Attach the cleaning tool
to the end of the hose.

2

Fill the tank
according
to page 8 to
prepare your
machine.

5

31

Set the Ready Tools Dial
to the Tools setting. This
will allow the machine
to divert the spray and
suction to the hose.

Plug the power cord into a
grounded outlet and press the
Power Switch Pedal to turn the
machine ON.

Be cautious: the brush roll on
the foot of the machine will spin
while using the hose. Ensure the
machine is not reclined or tilted
while using the hose.

Press the trigger on the hose to spray solution on to the area you are cleaning. Slowly move the
tool back and forth over the soiled surface. Release the trigger to suction up the soiled area. Work
in small sections. Optional: Spray and suction with only warm water to rinse the cleaned area.

NOTE: It is recommended that you suction
warm water from the tap to rinse out the
hose. Before wrapping the hose back on the
machine, extend the hose to ensure water is
out of the hose. Allow the hose and tool time
to dry before storing.

WARNING

WARNING: To reduce the risk of injury, be extra careful when cleaning stairs. Make sure the
machine is secure and level.

www.BISSELL.com

10