Biostar TPOWER N750 BIOS MANUAL

TP ow er N750 BIOS Manu al

B IOS Set up.... ............ ............ ............ ............ ............ ............ ............ .........1

1 Main Menu...............................................................................................3

2 Adv anc ed Menu...... ............ ............ ............ ............ ............ ............ .........7

3 PCIPnP Menu........................................................................................19

4 Bo o t Men u..............................................................................................22

5 Chipset Menu.........................................................................................24

6 T-Power Menu.......................................................................................26

7 Exit Me nu...............................................................................................36

TP ow er N750 BIOS Manu al

BIOS Setup

Introduction

The purpose of this manual is to describe the settings in the AMI BIOS Setup program on this motherboard. The Setup program allows users to modify the basic

system configuration and save these settings to CMOS RAM. The power of CMOS RAM is supplied by a battery so that it retains the Setup information when the power is turned off.

Basic Input-Output System (BIOS) determines what a computer can do without accessing programs from a disk. This system controls most of the input and output

devices such as keyboard, mouse, serial ports and disk drives. BIOS activates at the first stage of the booting process, loading and executing the operating system. Some additional features, such as virus and password prot ection or chipset fine-tuning options are also included in BIOS. The rest of this manual will to guide you through the options and settings in BIOS Setup.

Plug and Play Support

This AMI BIOS supports the Plug and Play Version 1.0A specification.

EPA Green PC Support

This AMI BIOS supports Version 1.03 of the EPA Green PC specification.

APM Support

This AMI BIOS supports Version 1.1&1.2 of the Advanced Power Management (AP M) speci fic ation. Power m anagem ent feat ures are implemented via the Syst em

Management Interrupt (SMI). Sleep and Suspend power management modes are supported. Power to the hard disk drives and video monitors can also be managed by

this AMI BIOS.

ACPI Supp ort

AMI ACPI BIOS support Version 1.0/2.0 of Advanced Configuration and Power interface specification (ACPI). It provides ASL code for power management and

device con figuration capabilities as defined in the ACPI specification, developed by Microso ft, Intel and T oshiba.

TP ow er N750 BIOS Manu al

PCI Bus Support

This AMI BIOS also supports Version 2.3 of the Intel PCI (Peripheral Component Int erconn ect) local bus s peci fic ation.

DRA M Support

DDR2 SDRAM (Double Data Rate II Synchronous DRAM) is supported.

Su ppor t e d CP Us

This AMI BIOS supports the AMD CPU.

Using Setup

W hen starting up t he computer, press

<Del> during the Power-On Self-Test (POST) to enter the BIOS setup utility.

In the BIOS setup utility, you will see

General Help description at the top right

corner, and this is providing a brief description of the selected item.

Navigation Keys for that particular menu

are at the bottom right corner, and you can use these keys to select item and ch ange the settings.

Notice

z The default BIOS settings apply for most conditions to ensure optimum performance

of the motherboard. If the system becomes unstable after changing any settings, please load the default settings to ensure system’s compatibility and stability. Use

Load Setup Default under the Exit Menu.

z For better system perform ance, the BIOS firmwa re is being continuously updated.

The BIOS information described in this manual is for your reference only. The actual BIOS information and settings on board may be slightly different from this manual.

z The content of this manual is subject to be changed without notice. We will not be

responsible for any mistakes found in this user’s manual and any system damage that may be caused by wrong-settings.

General Help

Navigati on Keys

TP ow er N750 BIOS Manu al

1 Main Menu

Once you enter AMI BIOS Setup Utility, the Main Menu will appear on the screen providing an overview of the basic system inform ation.

Main Advan ced PCIPnP Boot Chipset T-Power

System Overvie w AMI BIOS

Version :01. 01.01 Build Date:01/ 01/08 NVMM ROM Versi on :X.XXX.XX

BIOS SETU P UTILITY

Exit

Use [ENTER], [TAB] or [SHIFT-TAB] to

select a field. Use [+] or [-] to

configure system Time.

System Time 00

System Date [Tue 01/01/2008] Floppy A

> IDE Configur ation

[ :00:00]

Select Screen Select Item Change Field

Select Field

Tab

General Help

Save and Exit

F10

Exit

ESC

AM I BIOS

Shows system information including BIOS version, built date, etc.

System Time

Set the system internal clock.

System Date

Set the system date. Note that the ‘Day’ automatically changes when you set the date.

Floppy A

Select the type of floppy disk drive installed in your system. Options: 360K, 5.25 in / 1.2M, 5.25 in / 720K, 3.5 in / 1.44M, 3.5 in /

2.88M, 3.5 in / None

TP ow er N750 BIOS Manu al

IDE Configuration

T he BIOS wi ll automat ically detect t he presenc e of ID E/ SAT A devices. There is a sub-menu for each IDE/S AT A device. S elect a devi ce and press <Enter> to enter

the sub-menu of detailed options.

Main

IDE Confugurat ion

OnChip P-ATA C ontroller [Enabled]

OnChip S-ATA C ontroller [Enabled] SATA Mode Sele ct [SATA Mode] Change the AHC I DID for Linux[Disabled]

> Primary IDE Master > Primary IDE Slave > SATA 1 Devic e

> SATA 2 Devic e > SATA 3 Devic e > SATA 4 Devic e > SATA 5 Devic e > SATA 6 Devic e

Hard Disk Writ e Protect [Disabled] IDE Detect Tim e Out (Sec) [35]

OnChip P-ATA Controller

BIOS SETU P UTILITY

DISABLED: disables the integrated IDE

Controller. ENABLED: enables the integrated IDE Controller.

Select Screen Select Item Go to Sub Screen

Enter

General Help

Save and Exit

F10

Exit

ESC

This item allows you to control the onboard IDE controller. Options: Enabled (Default) / Disabled

OnChip S-ATA Controller

This item allows you to control the onboard SATA controller. Options: Enabled (Default) / Disabled

SATA M ode Select

This item allows you to choose the SATA operation mode. T o set SATA5/SATA6 device, please choose AHCI.

Options: SATA Mode (Default) / RAID / AHCI / Linux AHCI

Cha nge the AHCI DI D for Linux

This item appears only when SAT A mode is set to Linux AHCI. Options: Disabled (Default) / Enabled

TP ow er N750 BIOS Manu al

Primary IDE Master/Slave ; SATA 1/2/3/4/5/6 Device (SATA 5/6 Devi ce appears only when S ATA Mode is se t to AHCI )

Main

Primary IDE Master

Device :

Type [Auto]

LBA/Large Mode [Auto] Block (Multi-Sector Transfer)[Auto]

PIO Mode [Auto] DMA Mode [Auto]

S.M.A.R.T [Auto] 32Bit Data Transfer [Enabled]

BIOS SETUP UTILITY

Select the type of device connected to the system.

Select Screen Select Item Change Option

General Help

Save and Exit

F10

Exit

ESC

T he B IOS detect s the i nformation and values of resp ective devices, and thes e information and values are shown below to the name of the sub-menu.

Type

Select the type of the IDE/SATA drive. Options: Auto (Default) / CDROM / ARMD / Not Installed

LBA/Large Mode

Enable or disable the LBA mode. Options: Auto (Default) / Disabled

Block (Mu lti-Sector Transfer)

Enable or disable m ulti-sector trans fer. Options: Auto (Default) / Disabled

PIO Mode

Select the PIO mode. Options: Auto (Default) / 0 / 1 / 2 / 3 / 4

DMA Mode

Select the DMA mode. Options: Auto (Default) / Disabled

TP ow er N750 BIOS Manu al

S.M.A.R.T

Set the Smart Monitoring, Analysis, and Reporting Technology. Options: Auto (Default) / Disabled / Enabled

32Bit Data Tran sfer

Enable or disable 32-bit data transfer. Options: Enabled (Default) / Disabled

Har d Disk Write Protec t

Disable or enable device write protection. T his will be effective only if the device is accessed through BIOS.

Options: Disabled (Default) / Enabled

IDE Detect Time Out (Sec)

Select the time out value for detecting IDE/SATA devices. Options: 35 (Default) / 30 / 25 / 20 / 15 / 10 / 5 / 0

TP ow er N750 BIOS Manu al

2 Advanced Menu

The Advanced Menu allows you to configu re the settings of CPU, Super I/O, Power Management, and other system devices.

Notice

z Beware of that setting inappropriate values in items of this menu may cause

system to malfunction.

Main Advanced PCIPnP Boot Chipset T-Power

WARNING: Setti ng wrong values in below sections may c ause system to malfunction.

> CPU Configur ation

> SuperIO Conf iguration > Hardware Hea lth Configuration > Smart Fan Co nfiguration

> Power Config uration > USB Configur ation

> AUDIO Config uration > Onboard LAN Configuration

BIOS SETU P UTILITY

Configure CPU.Advanced Setti ngs

Exit

Select Screen Select Item

Go to Sub Screen

Enter

General Help

Save and Exit

F10

Exit

ESC

CPU Configurati on

This item shows the CPU information that the BIOS automatically detects.

Advan ced

CPU Configurat ion

Module Version : AGESA Version: Physical Count : Logical Count:

AMD CPU Revision:

Cache L1: Cache L2: Cache L3: Speed : Current FSB Mu ltiplier: Maximum FSB Mu ltiplier: Able to Change Freq : uCode Patch Le vel :

Secure Virtual Machine Mode [Enab led]

PowerNow [Enab led] ACPI SRAT Tabl e [Enab led]

BIOS SETU P UTILITY

Enable/Disable Secure Virtual Machine

Mode (SVM)

Select Screen Select Item Change Option

General Help

Save and Exit

F10

Exit

ESC

TP ow er N750 BIOS Manu al

Secure Virt ual Machine Mode

Virtualization T echnology can virtually separate your system resource into several parts, thus enhance the performance when running virtual machines or multi interface systems.

Options: Enabled (Default) / Disabled

PowerNow

This item allows you to enable or disable the PowerNow power saving technology. Options: Enabled (Default) / Disabled

ACPI SRAT Table

T he operating system scans the ACP I SRAT at boot time and uses the information to better allocate memory and schedule softwar e threads for maximum perform ance. This item controls whether the SRAT is made available to the operating system at boot up, or not. Options: Enabled (Default) / Disabled

S uperI O Co n f i g urat io n

Advan ced

Configure ITE8 718 Super IO Chipset

Onboard Floppy Controller [Enab led]

Serial Port1 A ddress [3F8/ IRQ4] Parallel Port Address [378] Parallel Por t Mode [Norm al]

Parallel Por t IRQ [IRQ7 ] Keyboard Power On [Disa bled] Mouse PowerOn [Disa bled] Restore on AC Power Loss [Powe r Off]

BIOS SETU P UTILITY

Allows BIOS to Enable or Disable Floppy

Controller

Select Screen Select Item Change Option

General Help

Save and Exit

F10

Exit

ESC

Onboard Floppy Controlle r

Select enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If you installed another FDC or the system uses no floppy drive, select disabled in this field. Options: Enabled (Default) / Disabled

TP ow er N750 BIOS Manu al

Serial Port1 Address

Select an address and corresponding interrupt for the first and second seri al ports. Options: 3F8/IRQ4 (Default) / 2F8/IRQ3 / 3E8/IRQ4 / 2E8/IRQ3 / Auto / Disabled

Parallel Port Address

T his item all ows you to d etermine access onboard parallel port controller with which I/O Address.

Options: 378 (Default) / 278 / 3BC / Disabled

Parallel Port Mode

This item allows you to determine how the parallel port should function. Options: Normal (Default) Using Parallel port as Standard Printer Port. EPP Using Parallel Port as Enhanced Parallel Port. ECP Using Parallel port as Extended Capabilities Port. ECP+EPP Using Parallel port as ECP & EPP mode.

Parallel Port IRQ

This item allows you to select the IRQ for the onboard parallel port. Options: IRQ7 (Default) / IRQ5 / Disabled

Keyboard PowerOn

This item allows you to control the keyboard power on function. Options: Disabled (Default) / Enabled

Mouse PowerOn

This item allows you to control the mouse power on function. Options: Disabled (Default) / Enabled

Restore on AC Power Loss

This setting specifies how your system should behave after a power fail or interrupts occurs. By choosi ng Disabled will leave the computer in the power off state.

Choosing Enabled will restore the system to the status before power failure or interrupt occurs. Options: Power Off (Default) / Power ON / Last State

TP ow er N750 BIOS Manu al

Hardware Health C onfiguration

This item shows the system temperature, fan speed, and voltage information.

Advan ced

Hardware Healt h Configuration

H/W Health Fun ction [Enab led]

Shutdown Tempe rature [Disa bled]

CPU Temperatur e System Tempera ture CPU FAN Speed SYS FAN Speed Chip FAN Speed

CPU Vcore Chipset Voltag e +3.30V +5.00V +12.0V HT Voltage

Memory Voltage 5V(SB) Voltage Batter y

H/W Health Function

If you computer contains a monitoring system, it will show PC health status during POST s tage. Options: Enabled (Default) / Disabled

Shutdow n Temperature

BIOS SETU P UTILITY

Enables Hardware Health Monitoring

Device.

Select Screen Select Item Change Option

General Help

Save and Exit

F10

Exit

ESC

This item allows you to set up the CPU shutdown T emperature. This item is only effective under Windows 98 ACPI mode.

Options: Disabled (Default) / 60℃/140℉ / 6 5 ℃/149℉ / 7 0 ℃/158℉ / 75℃/167℉

/ 80℃/176℉ / 85℃/185℉ / 90℃/194℉

TP ow er N750 BIOS Manu al

Smart Fan Configuration

Advan ced

Smart Fan Conf iguration

CPU Smart Fan [Disa bled]

Smart Fan Cali bration Control Mode Fan Ctrl OFF( C ) Fan Ctrl On(C) Fan Ctrl Start value Fan Ctrl Sensi tive

BIOS SETU P UTILITY

When you choice [Auto] ,[3Pin] or [4Pin],

please run the calibration to define the Fan parameters for Smart Fan control

Select Screen Select Item Change Option

General Help

Save and Exit

F10

Exit

ESC

CPU Sm a r t Fan

This item allows you to control the CP U Smart Fan function. Options: Disabled (default) / Auto / 4-pin / 3-pin

Sm art Fan Cali bration

Choose this item and then the BIOS will auto test and detect the CPU/System fan functions and show CPU/System fan speed.

Control Mode

This item provides several oper ation modes of the fan. Options: Quiet / Performan ce / Manual

Fan Ctrl OF F(℃ )

If the CPU/System Temperature is lower than the set value, FAN will turn off. Options: 0~127 (℃)

Fan Ctrl On(℃ )

CPU/System fan starts to work under smart fan function when arrive this set value. Options: 0~127 (℃)

+ 27 hidden pages

Biostar TPOWER N750 BIOS MANUAL

Specifications and Main Features

Frequently Asked Questions

User Manual