How it Works
Biostar
Loading...
M7VIG Pro
Owner's Manual
55 pgs902.72 Kb0

Biostar M7VIG Pro Owner's Manual

M
7
V
I
G
P
r
o
M
M
7
7
V
V
I
I
G
G
P
P
r
o
r
o
FCC Statement and Copyright
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the contents here of and specially disclaims any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves the right to revise this publication and to make changes to the contents here of without obligation to notify any party beforehand. Duplication of this publication, in part or in whole is not allowed without first obtaining the vendor’s approval in writing.
The content of this user’s is subject to be changed without notice and we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.
C
o
n
t
e
n
t
s
C
o
n
C
o
n
ENGLISH................................................................................................................1
M7VIG P ro Features ......................................................................................................................1
Package co ntents .......................................................................................................................... 2
Layout of M7VIG ProCPU Installation ...................................................................................... 2
CPU Installation..............................................................................................................................3
DD R DIMM Modules: DDR1-2 ..................................................................................................... 4
SDR DIMM Modules: SDR1-2...................................................................................................... 4
Jumpers, Headers, Connectors & Slots ..................................................................................6
t
e
n
t
s
t
e
n
t
s
ESPAÑOL ............................................................................................................11
Características del M7VIG Pro ................................................................................................. 11
Contenido del Paquete...............................................................................................................12
Disposición del M7VIG Pro .......................................................................................................12
Instalación de la CPU..................................................................................................................13
Módulos DDR DIMM: D DR1-2...................................................................................................14
Módulo SDR DIMM: SD R1-2......................................................................................................14
Conectores, Cabezales, Puentes y Ranuras........................................................................16
TROUBLE SHOOTING......................................................................................21
SOLUCIÓN DE PROBLEMAS.........................................................................22
ii
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
i
p
t
i
o
n
M
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
o
t
h
e
r
b
o
a
r
d
D
i
e
s
c
r
i
p
t
i
o
n
p
t
i
o
n
English
M7VIG Pro Features
Use VIA VT8375 (KM266)/ VT8235 Chipset, Winbond W83697HF, LAN
Chip- VT6103 (optional).
Contains on board I/O facilities, which include one serial port, one VGA port,
a parallel port, a PS/2 mouse port, a PS/2 keyboard port, audio ports, USB
2.0 ports, a LAN port (optional) and a game port.
Supports the single AMD Socket A for Athlon™ (Thunderbird™ ) / Athlon
XP™ / Duron ™ processors running at 200/266 MHz Front Side Bus (FSB).
Supports Ultra 133/100/66/33, PIO modes, IDE hard disk drives, LBA
mode.
Supports 2 DDR 200/266 MHz (without ECC) devices, maximun memory
size up to 2GB.
Supports 2 SDR 100/133 MHz (without ECC) devices, maximun memory
size up to 2 GB.
Supports one CNR Slot (Type B only), three 32-bit PCI Bus slots, and one
AGP Slot.
Complies with PC Micro-ATX form factor specifications.
Supports popular operating systems such as Windows NT, Windows 2000,
Windows ME, Windows XP, LINUX and SCO UNIX.
AC’97 2.2 compatible.
High S/N ratio meets PC 99 requirements.
6CH DAC, applicable for leading motherboard chipsets. Line-in phonejack share with rear out.
Supports front audio pin head functions.
1
M
V
V
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
i
p
t
i
o
n
M
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
o
t
h
e
r
b
o
a
r
d
D
i
e
s
c
r
i
p
t
i
o
n
p
t
i
o
n
Package contents
HDD Cable X 1, FDD Cable X 1, Fully Setup Driver CD X 1
Flash Memory Writer for BIOS update X 1
USB Cable X 2 (Optional) Rear I/O Panel for AT X Case X 1 (Optional)
Layout of M7VIG Pro
JCO M1
JVGA 1
JSPKR1
SP-OUT
JLIN1
LINE-IN
JM IC1
JM IC1
MIC-IN
2
1
Codec
1
JCODEC SEL
JKBMS1
JK BV1
1
JUSBV1
JUSBLAN1
JPRNT1
JAUD GAME
GAME Port
14 13
1
1
JCFAN1
PCI1
PCI2
PCI3
JATX PWR1
FDD 1
1
SDR1
SDR2
DDR2
DDR1
FLOPP Y DISK CONN.
T8375
(KM 266)
PR IMARY IDE CONN .
SECONDARY I DE CON N.
IDE1 IDE2
BAT1
JCMOS1
JPANEL1
1
2324
12
1
JSFAN 1
JWOL1
1
JU SB2
2
1
10
2
9
1
LAN Chip
Winbond I /O
JUSB3
JDIMMVOLT
127
10 9
T8235
8
2
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
i
p
t
i
o
n
M
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
o
t
h
e
r
b
o
a
r
d
D
i
e
s
c
r
i
p
t
i
o
n
p
t
i
o
n
CPU Installation
C
P
1. Pull the lever sideways away from the socket then raise the lever up to 90-degree angle.
2. Locate Pin A in the socket and lock for the white dot or cut edge in the CPU. Match Pin A with the white dot/cut edge then insert the CPU.
3. Press the lever down. Then Put the fan on the CPU and buckle it and put the fan’s power port into the JCFAN1, then to complete the
installation.
CPU/ System Fan Headers: JCFAN1/ JSFAN1
1
JCFAN1
U
Sense
12V
Ground
1
Ground 12V Sense
JSFAN1
3
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
i
p
t
i
o
n
M
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
o
t
h
e
r
b
o
a
r
d
D
i
e
s
c
r
i
p
t
i
o
n
p
t
i
o
n
DDR DIMM Modules: DDR1-2
DRAM Access Time: 2.5V Unbuffered DDR 200/266 MHz Type required. DRAM Type: 64MB/ 128MB/ 256MB/ 512MB/ 1GB DIMM Module (184 pin)
DIMM Socket
Location
DDR 1 64MB/128MB/256MB/512MB/1GB
DDR 2 64MB/128MB/256MB/512MB/1GB
z The list shown above for DRAM configuration is only for reference.
DDR Module Total Memory
Size (MB)
*1
*1
Max is
2GB
SDR DIMM Modules: SDR1-2
DRAM Access Time: 3.3V Unbuffered SDR 100/133 MHz Type required. DRAM Type: 64MB/ 128MB/ 256MB/ 512MB/ 1GB DIMM Module (184 pin)
DIMM Socket
Location
SDR 1 64MB/128MB/256MB/512MB/1GB
SDR 2 64MB/128MB/256MB/512MB/1GB
z The list shown above for DRAM configuration is only for reference.
0When you use DDR S DRAM, the memory power wil l
automatically set to 2.5V.
0When you use SDRAM, the memory power will automatically set to 3.3V.
SDR Module Total Memory
Size (MB)
*1
*1
Max is
2GB
0
For the above settings, you can only use one kind of memory on
this motherboard. It is forbidden to insert both kind of memory simultaneously. You must insert only DDR or SDRAM.
4
M
o
t
h
e
r
b
o
a
r
d
D
M
M
o
t
h
e
r
b
o
o
t
h
e
r
b
o
e
a
r
d
D
a
r
d
D
How to install a DIMM Module DDR SDRAM
1. The DIMM socket has a “ Plastic Safety Tab”, and the
DIMM memory module has an “Asymmetrical notch”, so the DIMM memory module can only fit into the slot in one direction.
2. Push the tabs out. Insert the DIMM memory modules into the
socket at a 90-degree angle, then push down vertically so that it will fit into the place.
3. The Mounting Holes and plastic tabs should fit over the edge and
hold the DIMM memory modules in place.
SDRAM
1. The DIMM socket has a “ Plastic Safety Tab”, and the DIMM memory module has an “Asymmetrical notch”, so the DIMM memory module can only fit into the slot in one direction.
2. Push the tabs out. Insert the DIMM memory modules into the socket at a 90-degree angle, then push down vertically so that it will fit into the place.
3. The Mounting Holes and plastic tabs should fit over the
edge and hold the DIMM memory modules in place.
s
c
r
i
p
t
i
o
n
e
s
c
r
i
e
s
c
r
i
p
t
i
o
n
p
t
i
o
n
5
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
i
p
t
i
o
n
M
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
o
t
h
e
r
b
o
a
r
d
D
i
e
s
c
r
i
p
t
i
o
n
p
t
i
o
n
Jumpers, Headers, Connectors & Slots
Hard Disk Connectors: IDE1/ IDE2
The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO Mode 0~4, Bus Master, and Ultra DMA / 33/ 66/ 100/ 133 functionality. It has two HDD connectors IDE1 (primary) and IDE2 (secondary). The IDE connectors can connect a master and a slave drive, so you can connect up to four hard disk drives. The first hard drive should always be connected to IDE1.
Floppy Disk Connector: FDD1
The motherboard provides a standard floppy disk connector that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the provided floppy drive ribbon cables.
Communication Network Riser Slot: CNR1
The CNR specification is an open Industry Standard Architecture, and it defines a hardware scalable riser card interface, which supports modem only.
Peripheral Component Interconnect Slots: PCI1-3
This motherboard is equipped with 3 standard PCI slots. PCI stands for Peripheral Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as 32 bits.
Accelerated Graphics Port Slot: AGP1
Your monitor will attach directly to that video card. This motherboard supports video cards for PCI slots, but it is also equipped with an Accelerated Graphics Port (AGP). An AGP card will take advantage of AGP technology for improved video efficiency and performance, especially with 3D graphics.
6
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
i
p
t
i
o
n
M
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
o
t
h
e
r
b
o
a
r
d
D
i
e
s
c
r
i
p
t
i
o
n
p
t
i
o
n
Power Connectors: JATXPWR1
JATXPWR1
JATXPWR1
(ATX Main Power Conn.)
(ATX Main Power Conn.)
DIMM Power Selection Connector: JDIMMVOLT
z It strongly recommended to set DDR DIMM voltage in default setting
2.5V, and it for over voltage function.
2
1
JDIMMVOLT
(Default ==> 2.5V)
Pin 1-2 on ==> 2.5V Pin 3-4 on ==> 2.6V Pin 5-6 on ==> 2.7V Pin 7-8 on ==> 2.8V
Wa ke On LAN Header: WO L1
Ground
5V_S B Wak e up
1
WOL1
Clear CMOS Jumper: JCMOS1
1
JCMOS1
Pin 1-2 on ==> Normal Operation (default) Pin 2-3 on ==> Clear CMOS Data
7
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
i
p
t
i
o
n
M
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
o
t
h
e
r
b
o
a
r
d
D
i
e
s
c
r
i
p
t
i
o
n
p
t
i
o
n
Front USB Header: JUSB2/ JUSB3
2 1
JUSB2/3
Pin1,2 ==> +5V Pin3,4 ==> Data(-) Pin5,6 ==> Data(+) Pin7,8 ==> Ground Pin9 ==> KEY Pin10 ==> NA
5V/ 5VSB Selection for USB: JUSBV1
1
JUSBV1
Pin 1-2 on ==> 5V
Pin 2-3 on ==> 5V_SB
CPU Frequency Se lection: JCLK1
1
JCLK1
On ==> 100MHz
Off ==> 133MHz
5V/ 5VSB Selection for Keyboard: JKBV1
1
JKBV1
Pin 1-2 on ==> 5V
Pin 2-3 on ==> 5V_SB
8
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
i
p
t
i
o
n
M
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
o
t
h
e
r
b
o
a
r
d
D
i
e
s
c
r
i
p
t
i
o
n
p
t
i
o
n
CNR Codec Primary/ Secondary Selection:
JCODECSEL
1
JCODECSEL
Pin 1-2 ==> On board primary Codec (Default)
Pin 2-3 ==> CNR primary Codec
Front Panel Connector: JPANEL1
PWR_LED HLED
ON/OFF
SLP
24
IR
(+)
(+)
23
(-)
2
(-)
(+)
1
SPK ==> Speaker Conn.
IR
HLED ==> Hard Driver LED
RST ==> Reset Button
RST
IR ==> Infrared Conn.
SLP ==> Sleep Button
PWR_LED ==> Power LED
SPK
ON/ OFF ==> Power-on Button
Audio Subsystem: JF_AUDIO/ JCDIN1
2
2 1
1
JAUDIO1
JF_AUDIO
(Front Audio Header)
(Front Audio Header)
JCDIN1
JCDIN1
(CD-ROM Audio-In Header)
(CD-ROM Audio-In Header)
1
1
9
M
o
t
h
e
r
b
M
o
M
o
2
1
Pin1 ==> Mic In Pin2 ==> Ground Pin3 ==> Mic Power Pin4 ==> Audio Power Pin5 ==> RT Line Out Pin6 ==> RT Line Out Pin7 ==> Reserved Pin8 ==> KEY Pin9 ==> LFT Line Out Pin10 ==> LFT Line Out Pin11==> RT Line In Pin12 ==> RT Line In Pin13 ==> LFT Line In Pin14 ==> LFT Line In
o
t
h
e
r
b
o
t
h
e
r
b
o
Back Panel Connectors
a
r
d
D
e
s
c
r
i
p
t
i
o
n
a
r
d
D
e
s
c
r
a
r
d
D
14
13
i
e
s
c
r
i
JF_AUDIO
p
t
i
o
n
p
t
i
o
n
JKBMS1
PS/2 Mouse
PS/2 Keyboard
JUSBLAN1
LAN(Optional)
USB
COM1
JCOM1
JPRNT1 JGAME1
Parallel
VGA1
JVGA1
10
Speaker
Out
Game Port
Line In Mic
In
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
i
p
t
i
o
n
M
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
o
t
h
e
r
b
o
a
r
d
D
i
e
s
c
r
i
p
t
i
o
n
p
t
i
o
n
Español
Características del M7VIG Pro
Usa Chipset VIA VT8375 (KM266)/ VT8235, Winbond W83697HF, LAN
Chip- VT6103 (opcional).
Contiene facilidades I/O integrados en la placa madre en el que incluye un
puerto en serie, un puerto VGA, un puerto paralelo, un puerto de ratón PS/2, un puerto de teclado PS/2, puerto de audio, puertos USB 2.0, un
puerto LAN (opcional) y un puerto de juego.
Soporta single AMD Socket A para procesadores Athlon™
(Thunderbird™)/ Athlon XP™ / D u ro n™ corriendo a 200/266 MHz Front Side Bus (FSB).
Soporta Ultra 133/100/66/33, modos PIO, discos duros IDE, modo LBA.
Soporta 2 dispositivos DDR 200/266 MHz (sin ECC), memoria máxima de
hasta 2 GB.
Soporta 2 dispositivos SDR 200/266 MHz (sin ECC), memoria máxima de
hasta 2 GB.
Soporta una ranura CNR (solamente de Tipo B), tres ranuras PCI Bus de
32-bit, y una ranura AGP.
Conforma con las especificaciones del factor de forma de tamaño PC
Micro-ATX.
Soporta sistemas operativos populares tales como Windows NT, Windows
2000, Windows ME, Windows XP, LINUX y SCO UNIX.
Compatible con AC’97 2.2.
High S/N ratio reune los requisitos del PC 99.
6CH DAC, aplicables para chipsets de principales placas madres.
Entrada de Línea compartido con el rear out. Soporta funciones del cabezal de contactos del audio frontal.
11
M
V
V
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
i
p
t
i
o
n
M
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
o
t
h
e
r
b
o
a
r
d
D
i
e
s
c
r
i
p
t
i
o
n
p
t
i
o
n
Contenido del Paquete
Cable HDD X 1, Cable FDD X 1, Configuración Completa del Driver CD X
1
Flash Memory Writer para actualización del BIOS X 1 Cable USB X 2 (Opcional)
Panel Trasero I/O para Caja ATX X 1 (Opcional)
Disposición del M7VIG Pro
JCOM1
JVGA1
JSPK R1
Salida del Altavoz
JLIN1
Entrad a de Linea
JMIC1
JMIC1
Entrad a del MIC
2 1
Codec
1
JCODECSEL
JKBMS1
JKBV 1
1
JUSB V1
JUSBL AN1
JPRNT 1
JAUD GAME
Puerto de Juego
14 13
1
1
JCFAN1
PCI1
PCI2
PCI3
JATXPWR1
FDD1
1
SDR2
SDR1
DDR1
DDR2
T8375
(KM 266)
IDE 1 ID E2
BAT1
JCMO S1
JPANEL1
1
JSFAN1
2324
12
1
JWOL1
1
JUSB2
2
1
10
2 1
9
LAN C hip
Win bond I/O
JUSB3
JDIMMVOLT
127
10 9
T8235
8
12
M
o
t
h
e
r
b
o
M
M
o
t
h
o
t
h
a
e
r
b
o
a
e
r
b
o
a
Instalación de la CPU
r
d
D
e
s
c
r
i
p
t
i
o
n
r
d
D
e
s
c
r
r
d
D
i
e
s
c
r
i
p
t
i
o
n
p
t
i
o
n
1. Tire de la palanca del lado del zócalo, luego levante la palanca hasta un ángulo de 90 grados.
2. Sitúe el contacto A del zócalo y busque el punto blanco o corte el borde en la CPU. Empareje el contacto A con el punto blanco/
corte del borde, luego inserte la CPU.
3. Presione la palanca para abajo. Ponga el ventilador en la CPU y abróchelo. Luego ponga el puerto de corriente del ventilador en el
JCFAN1. Y ya habrá completado su instalación.
C
P
U
CPU/ Cabezales del Sistema de Ventilación: JCFAN1/
JSFAN1
1
Sense
12V
Tierra
1
Tierra 12V Sense
JCFAN1
JSFAN1
13
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
i
p
t
i
o
n
M
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
o
t
h
e
r
b
o
a
r
d
D
i
e
s
c
r
i
p
t
i
o
n
p
t
i
o
n
Módulos DDR DIMM: DDR1-2
DRAM Tiempo de Acceso: 2.5V Unbuffered DDR 200/266 MHz Tipo requerido. DRAM Tipo: 64MB/ 128MB/ 256MB/ 512MB/ 1GB Módulo DIMM (184 pin)
Localización
del Módulo
DIMM
DDR 1 64MB/128MB/256MB/512MB/1GB
DDR 2 64MB/128MB/256MB/512MB/1GB
z La lista de arriba para la configuración DRAM es solamente para
referencia.
Módulo DDR
*1
*1
Total del
Tamaño de
Memoria (MB)
Máximo de
2GB
Módulo SDR DIMM: SDR1-2
DRAM Tiempo de Acceso: 3.3V Unbuffered SDR 100/133 MHz Tipo requerido. DRAM Tipo: 64MB/ 128MB/ 256MB/ 512MB/ 1GB Módulos DIMM (184
contactos)
Localización
del Módulo
DIMM
SDR 1 64MB/128MB/256MB/512MB/1GB
SDR 2 64MB/128MB/256MB/512MB/1GB
z La lista de arriba para la configuración DRAM es solamente para
referencia.
0Cuando use DDR SDRAM, la corriente de la me moria auto máticamente se configurará a 2.5V.
0Cuando use SDRAM, la corriente de la memoria auto máticamente se configurará a 3.3V.
Módulo SDR
*1
*1
Total del
Tamaño de
Memoria (MB)
Máximo de
2GB
14
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
i
p
t
i
o
n
M
o
t
h
e
r
b
o
a
r
d
D
e
s
c
r
M
o
t
h
e
r
b
o
a
r
d
D
0
Para la configuración arriba mencionada, usted solamente puede utilizar un sólo tipo de memoria en ésta placa madre. Está prohibido insertar los dos tipos de memoria simultáneamente. Solamente puede insertar DDR o SDRAM.
i
e
s
c
r
i
p
t
i
o
n
p
t
i
o
n
Cómo instalar un Módulo DIMM DDR SDRAM
1. El zócalo DIMM tiene una lengüeta plástica de seguridad y
el módulo de memoria DIMM tiene una muesca asimétrica, así el módulo de memoria DIMM puede caber solamente en la ranura de una sóla dirección.
2. Tire la lengüeta hacia afuera. Inserte los módulos de memoria
DIMM en el zócalo a los 90 grados, luego empuje hacia abajo verticalmente de modo que encaje en el lugar.
3. Los agujeros de montaje y las lengüetas plásticas deben caber
por sobre el borde y sostenga los módulos de memoria D IMM en el lugar.
SDRAM
1. El zócalo DIMM tiene una lengüeta plástica de seguridad y el módulo de memoria DIMM tiene una muesca asimétrica, así el módulo de memoria DIMM puede caber solamente en la ranura de una sóla dirección.
2. Tire la lengüeta hacia afuera. Inserte los módulos de memoria DIMM en el zócalo a los 90 grados, luego empuje
hacia abajo verticalmente de modo que encaje en el lugar.
3. Los agujeros de montaje y las lengüetas plásticas deben caber por sobre el borde y sostenga los módulos de memoria DIMM en el lugar.
15
Loading...
+ 38 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use