Biostar Hi-Fi A85S3+ Owner's Manual
Hi-Fi A85S3+/Hi-Fi A75S3+ Setup Manual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee that
interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the contents
here and specially disclaims any implied warranties of merchantability or fitness
for any purpose. Further the vendor reserves the right to revise this publication
and to make changes to the contents here without obligation to notify any party
beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and we
will not be responsible for any mistakes found in this user’s manual. All the brand
and product names are trademarks of their respective companies.
Dichiarazione di conformità
sintetica
Ai sensi dell’art. 2 comma 3 del D.M.
275 del 30/10/2002
Si dichiara che questo prodotto è
conforme alle normative vigenti e
soddisfa i requisiti essenziali richiesti
dalle direttive
2004/108/CE, 2006/95/CE e
1999/05/CE
quando ad esso applicabili
Short Declaration of conformity
We declare this product is complying
with the laws in force and meeting all
the essential requirements as specified
by the directives
2004/108/CE, 2006/95/CE and
1999/05/CE
whenever these laws may be applied
Table of Contents
Chapter 1: Introduction.......................................... 1
1.1 Before You Start ................................................................................1
1.2 Package Checklist ............................................................................1
1.3 Motherboard Specifications.............................................................2
1.4 Rear Panel Connectors....................................................................3
1.5 Motherboard Layout..........................................................................4
Chapter 2: Hardware Installation ........................... 5
2.1 Install Central Processing Unit (CPU)............................................ 5
2.2 Install a Heatsink...............................................................................6
2.3 Connect Cooling Fans......................................................................7
2.4 Install System Memory.....................................................................8
2.5 Expansion Slots...............................................................................10
2.6 Jumper Setting ................................................................................11
2.7 Headers & Connectors...................................................................12
Chapter 3: UEFI BIOS & Software ........................ 18
3.1 UEFI BIOS Setup............................................................................18
3.2 BIOS Update.................................................................................... 18
3.3 Software............................................................................................22
Chapter 4: Useful Help ......................................... 26
4.1 Driver Installation.............................................................................26
4.2 AMI BIOS Beep Code.....................................................................27
4.3 Troubleshooting...............................................................................27
4.4 RAID Functions ...............................................................................29
4.5 AMD Dual Graphics Technology...................................................31
Appendix: Specifications in Other Languages....... 34
Arabic.....................................................................................................................34
French ...................................................................................................................36
German .................................................................................................................38
Italian ..................................................................................................................... 40
Japanese...............................................................................................................42
Polish.....................................................................................................................44
Portuguese ...........................................................................................................46
Russian ................................................................................................................. 48
Spanish..................................................................................................................50
Hi-Fi A85S3+/Hi-Fi A75S3+
CHAPTER 1: INTRODUCTION
1.1 Before You Start
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
Prepare a dry and stable working environment with
sufficient lighting.
Always disconnect the computer from power outlet before
operation.
Before you take the motherboard out from anti-static bag,
ground yourself properly by touching any safely grounded
appliance, or use grounded wrist strap to remove the static
charge.
Avoid touching the components on motherboard or the rear
side of the board unless necessary. Hold the board on the
edge, do not try to bend or flex the board.
Do not leave any unfastened small parts inside the case
after installation. Loose parts will cause short circuits which
may damage the equipment.
Keep the computer from dangerous area, such as heat
source, humid air and water.
The operating temperatures of the computer should be 0 to
45 degrees Celsius.
To avoid injury, be careful of:
Sharp pins on headers and connectors
Rough edges and sharp corners on the chassis
Damage to wires that could cause a short circuit
1.2 Package Checklist
; Serial ATA Cable x2
; Rear I/O Panel for ATX Case x1
; User’s Manual x1
; Fully Setup Driver DVD x1
Note: The package contents may be different due to the sales region or models in which it was
sold. For more information about the standard package in your region, please contact your dealer
or sales representative.
1
Motherboard Manual
1.3 Motherboard Specifications
Specifications
Socket FM2 for AMD A-series processor
CPU Support
Chipset
Memory
Storage
LAN
Audio Codec
USB
Expansion Slots
Rear I/Os
Internal I/Os
2
Maximum CPU TDP (Thermal Design Power): 100Watt
* Please refer to www.biostar.com.tw
AMD A85 FCH (Hi-Fi A85S3+)
AMD A75 FCH (Hi-Fi A75S3+)
Supports Dual Channel DDR3 800/ 1066/ 1333/ 1600/ 1866
4 x DDR3 DIMM Memory Slot, Max. Supports up to 64 GB Memory
Each DIMM supports non-ECC 512MB/ 1/ 2/ 4/ 8/ 16 GB DDR3 module
* Please refer to www.biostar.com.tw
AMD A85/A75 FCH
Supports RAID 0,1,10, 5 & AHCI (AMD A85 FCH)
Supports RAID 0,1,10 & AHCI (AMD A75 FCH),
Realtek RTL 8111F
10/ 100/ 1000 Mb/s auto negotiation, Half / Full duplex capability
ALC662
5.1 Channels, High Definition Audio, Biostar Hi-Fi
AMD A85/A75 FCH:
6x USB 2.0 port (2 on rear I/Os and 4 via internal headers)
4x USB 3.0 port (2 on rear I/Os and 2 via internal headers)
1x PCI Slot
1x PCIe 2.0 x1 Slot
2x PCIe 2.0 x16 Slot (x16, x4)
1x PS/2 Mouse
1x PS/2 Keyboard
1x VGA Port
1x HDMI Port
1x DVI Port
1x LAN port
2x USB 2.0 Port
2x USB 3.0 Port
3x Audio Jack
Hi-Fi A85S3+:
8x SATA 6.0Gb/s Connector
2x USB 2.0 Header
1x USB 3.0 Header
1x 4-Pin Power Connector
1x 24-Pin Power Connector
1x CPU Fan Connector
1x System Fan Connector
1x Front Panel Header
1x Front Audio Header
1x Clear CMOS Header
1x Printer Port Header
1x Consumer IR Header
for CPU support list.
for Memory support list.
Hi-Fi A75S3+:
6x SATA 6.0Gb/s Connector
2x USB 2.0 Header
1x USB 3.0 Header
1x 4-Pin Power Connector
1x 24-Pin Power Connector
1x CPU Fan Connector
1x System Fan Connector
1x Front Panel Header
1x Front Audio Header
1x Clear CMOS Header
1x Printer Port Header
1x Consumer IR Header
Hi-Fi A85S3+/Hi-Fi A75S3+
Specifications
1x Serial Port Header
1x S/PDIF out Connector
Form Factor microATX Form Factor, 244 mm x 235 mm
Windows XP / Vista / 7/ 8
OS Support
Biostar reserves the right to add or remove support for any OS with or without
notice.
1x Serial Port Header
1x S/PDIF out Connector
1.4 Rear Panel Connectors
Note 1: HDMI / DVI-D / VGA Output require an AMD family processor with intedrated graphics.
Note 2: The mainboard supports three onboard display outputs at same time.
Note 3: Since the audio chip supports High Definition Audio Specification, the function of each
Note 4: Maximum resolution:
audio jack can be defined by software. The input / output function of each audio jack
listed above represents the default setting. However, when connecting external
microphone to the audio port, please use the Line In (Blue) and Mic In (Pink) audio jack.
Outputs Maximum resolution Bit Depth
HDMI
DVI-D
VGA 1920 x 1600 @60Hz --
1920 x 1080 @60Hz 24, 30, 36 bpp
1920 x 1200 @60Hz 24 bpp
1920 x 1200 @60Hz 30 bpp
2560 x 1600 @60Hz 24 bpp
3
Motherboard Manual
1.5 Motherboard Layout
Note1: ■ represents the 1st pin.
Note2: The SATA6 connector is only for Hi-Fi A85S3+.
4
Hi-Fi A85S3+/Hi-Fi A75S3+
CHAPTER 2: HARDWARE INSTALLATION
2.1 Install Central Processing Unit (CPU)
Step 1: Locate the CPU socket on the motherboard
Step 2: Pull the socket locking out from the socket and then raise the lever up to
a 90-degree angel.
Step 3: Look for the white triangle on socket, and the gold triangle on CPU
should point towards this white triangle. The CPU will fit only in the
correct orientation.
Note: The CPU fits only in one correct orientation. Do not force the CPU into the socket to
prevent damaging the CPU.
5
Motherboard Manual
Step 4: Hold the CPU down firmly, and then close the lever to locked the position
2.2 Install a Heatsink
Step 1: Place the heatsink and fan assembly onto the retention frame. Match the
heatsink clip with the socket mounting-lug. Hook the spring clip to the
mounting-lug.
Step 2: On the other side, push the retention clip straight down to lock into the
plastic lug on the retention frame, and then press down the locker until it
stops.
Note1: Do not forget to connect the CPU fan connector.
Note2: For proper installation, please kindly refer to the installation manual of your CPU
heatsink.
6
Hi-Fi A85S3+/Hi-Fi A75S3+
2.3 Connect Cooling Fans
These fan headers support cooling-fans built in the computer. The fan cable and
connector may be different according to the fan manufacturer. Connect the fan
cable to the connector while matching the black wire to pin#1.
CPU_FAN1: CPU Fan Header
Pin Assignment
1 Ground
2 +12V
3
FAN RPM rate sense
4 Smart Fan Control
(By Fan)
SYS_FAN1: System Fan Header
Pin Assignment
1 Ground
2 +12V
3
FAN RPM rate sense
Note: CPU_FAN1, SYS_FAN1 support 4-pin and 3-pin head connectors. When connecting
with wires onto connectors, please note that the red wire is the positive and should be
connected to pin#2, and the black wire is Ground and should be connected to GND.
7
Motherboard Manual
2.4 Install System Memory
A. DDR3 Modules
Step 1: Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM
on the slot such that the notch on the DIMM matches the break on the slot.
Step 2: Insert the DIMM vertically and firmly into the slot until the retaining chip
snap back in place and the DIMM is properly seated.
Note: If the DIMM does not go in smoothly, do not force it. Pull it all the way out and try again.
8
Hi-Fi A85S3+/Hi-Fi A75S3+
B. Memory Capacity
DIMM Socket
Location
DDR3_A1 512MB/1GB/2GB/4GB/8GB/16GB
DDR3_A2 512MB/1GB/2GB/4GB/8GB/16GB
DDR3_B1 512MB/1GB/2GB/4GB/8GB/16GB
DDR3_B2 512MB/1GB/2GB/4GB/8GB/16GB
DDR3 Module
Total Memory Size
Max is 64GB.
C. Dual Channel Memory Installation
Please refer to the following requirements to activate Dual Channel function:
Install memory module of the same density in pairs, shown in the table.
Dual Channel Status DDR3_A1 DDR3_A2 DDR3_B1 DDR3_B2
Enabled O X O X
Enabled X O X O
Enabled O O O O
(O means memory installed, X means memory not installed.)
Note: The DRAM bus width of the memory module must be the same (x8 or x16)
9
Motherboard Manual
2.5 Expansion Slots
PEX16_1: PCI-Express Gen2 x16 Slot
- PCI-Express 2.0 compliant.
- Maximum theoretical realized bandwidth of 8GB/s simultaneously per
direction, for an aggregate of 16GB/s totally.
- PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.
PEX16_2: PCI-Express Gen2 x4 Slot
- PCI-Express 2.0 compliant.
- Maximum theoretical realized bandwidth of 2GB/s simultaneously per
direction, for an aggregate of 4GB/s totally.
PEX1_1: PCI-Express Gen2 x1 Slot
- PCI-Express 2.0 compliant.
- Data transfer bandwidth up to 500MB/s per direction; 1GB/s in total
PCI1: Peripheral Component Interconnect Slot
This motherboard is equipped with 1 standard PCI slot. PCI stands for Peripheral
Component Interconnect, and it is a bus standard for expansion cards.
Install an Expansion Card
You can install your expansion card by following steps:
1. Read the related expansion card's instruction document before install the
expansion card into the computer.
2. Remove your computer's chassis cover, screws and slot bracket from the
computer.
3. Place a card in the expansion slot and press down on the card until it is
completely seated in the slot.
4. Secure the card’s metal bracket to the chassis back panel with a screw.
5. Replace your computer's chassis cover.
6. Power on the computer, if necessary, change BIOS settings for the
expansion card.
7. Install related driver for the expansion card.
10
Hi-Fi A85S3+/Hi-Fi A75S3+
2.6 Jumper Setting
The illustration shows how to set up jumpers. When the jumper cap is placed on
pins, the jumper is “close”, if not, that means the jumper is “open”.
Pin opened Pin closed Pin1-2 closed
JCMOS1: Clear CMOS Header
Placing the jumper on pin2-3, it allows user to restore the BIOS safe setting and
the CMOS data. Please carefully follow the procedures to avoid damaging the
motherboard.
31
Pin 1-2 Close:
Normal Operation (default).
Pin 2-3 Close:
Clear CMOS data.
※ Clear CMOS Procedures:
1. Remove AC power line.
2. Set the jumper to “Pin 2-3 close”.
3. Wait for five seconds.
4. Set the jumper to “Pin 1-2 close”.
5. Power on the AC.
6. Load Optimal Defaults and save settings in CMOS.
31
11
Motherboard Manual
2.7 Headers & Connectors
ATXPWR1: ATX Power Source Connector
This connector allows user to connect 24-pin power connector on the ATX power
supply.
Pin Assignment Pin Assignment
13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 Ground 3 Ground
16 PS_ON 4 +5V
17 Ground 5 Ground
18 Ground 6 +5V
19 Ground 7 Ground
20 NC 8 PW_OK
21 +5V 9 Standby Voltage+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 Ground 12 +3.3V
ATXPWR2: ATX Power Source Connector
This connector will provide +12V to CPU power circuit.
Note1: Before you power on the system, please make sure that both ATXPWR1 and
ATXPWR2 connectors have been plugged-in.
Note2: Insufficient power supplied to the system may result in instability or the
peripherals not functioning properly. Use of a PSU with a higher power output is
recommended when configuring a system with more power-consuming devices.
12
Pin Assignment
1 +12V
2 +12V
3 Ground
4 Ground
Hi-Fi A85S3+/Hi-Fi A75S3+
PANEL1: Front Panel Header
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.
Pin Assignment Function Pin Assignment Function
1 +5V 9 N/A
2 N/A 10 N/A
3 N/A 11 N/A N/A
4 Speaker
5 HDD LED (+) 13 Power LED (+)
6 HDD LED (-)
7 Ground 15 Power button
8 Reset control
Speaker
Connector
Hard drive LED
Reset button
12 Power LED (+)
14 Power LED (-)
16 Ground
N/A
Power LED
Power-on button
SATA1~SATA6: Serial ATA Connectors
These connectors connect to SATA hard disk drives via SATA cables.
Hi-Fi A85S3+ & Hi-Fi A75S3+ satisfy the SATA 3.0 spec and with transfer rate of
6.0Gb/s.
The SATA6 (SATA6-U/SATA6-L) connector is only for Hi-Fi A85S3+.
Pin Assignment
1 Ground
2 TX+
3 TX4 Ground
5 RX6 RX+
7 Ground
13
Motherboard Manual
JFRONT_USB3_1: Header for USB 3.0 Ports at Front Panel
This header allows user to connect additional USB cable on the PC front panel,
and also can be connected with a wide range of simultaneously accessible
external Plug and Play peripherals.
Pin Assignment Pin Assignment
1 VBUS0 11 D2+
2 SSRX1- 12 D23 SSRX1+ 13 Ground
4 Ground 14 SSTX2+
5 SSTX1- 15 SSTX26 SSTX1+ 16 Ground
7 Ground 17 SSRX2+
8 D1- 18 SSRX29 D1+ 19 VBUS1
10 ID 20 Key
F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel
This header allows user to connect additional USB cable on the PC front panel,
and also can be connected with a wide range of simultaneously accessible
external Plug and Play peripherals.
14
Pin Assignment
1 +5V (fused)
2 +5V (fused)
3 USB4 USB5 USB+
6 USB+
7 Ground
8 Ground
9 NC
10 Key
Loading...