Biostar GF8200 M2+ Owner's Manual

GF8200 M2+ Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.

Table of Contents

Chapter 1: Introduction ............................................................ 1

1.1 Before You Start ................................................................................ 1

1.2 Package Checklist............................................................................. 1

1.3 Motherboard Features...................................................................... 2

1.4 Rear Panel Connectors ..................................................................... 3

1.5 Motherboard Layout......................................................................... 4

Chapter 2: Hardware Installation ............................................. 5

2.1 Installing Central Processing Unit (CPU) ....................................... 5

2.2 FAN Headers...................................................................................... 7

2.3 Installing System Memory ................................................................ 8

2.4 Connectors and Slots....................................................................... 10

Chapter 3: Headers & Jumpers Setup ..................................... 12

3.1 How to Setup Jumpers .................................................................... 12

3.2 Detail Settings.................................................................................. 12

Chapter 4: RAID Functions ..................................................... 19

4.1 Operation System............................................................................ 19

4.2 Raid Arrays...................................................................................... 19

4.3 How RAID Works............................................................................. 19

Chapter 5: Useful Help ............................................................ 23

5.1 Driver Installation Note.................................................................. 23

5.2 Software............................................................................................ 24

5.3 Extra Information............................................................................ 28

5.4 AMI BIOS Beep Code....................................................................... 30

5.5 Troubleshooting............................................................................... 31

Appendencies: SPEC In Other Language ................................ 32

German.................................................................................................................. 32

France .................................................................................................................... 34

Italian..................................................................................................................... 36

Spanish ................................................................................................................... 38

Portugue se ............................................................................................................ 40

Polish...................................................................................................................... 42

Russian ................................................................................................................... 44

Arabic..................................................................................................................... 46

Japanese ................................................................................................................ 48

CHAPTER 1: INTRODUCTION

GF8200 M2+

1.1 B

EFORE YOU START

Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with

sufficient lighting.

 Always disconnect the computer from power outlet

before operation.

 Before you take the motherboard out from anti-static

bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.

 Avoid touching the components on motherboard or the

rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the

case after installation. Loose parts will cause short
circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

1.2 PACKAGE CHECKLIST

HDD Cable X 1
Serial ATA Cable X 1
Rear I/O Panel for ATX Case X 1
User’s Manual X 1
Fully Setup Driver CD X 1
FDD Cable X 1 (optional)
USB 2.0 Cable X1 (optional)
S/PDIF out Cable X 1 (optional)
Serial ATA Power Cable X 1 (optional)
DVI to HDMI Adapter X 1 (optional)

Note: The package contents may differ by area or your motherboard version.

1

Motherboard Manual

/

1.3 MOTHERBOARD FEATURES

SPEC

Socket AM2+

CPU

FSB

Chipset GeForce 8200

Super I/O

Main

Memory

Graphics Integrated in GeForce 8200 Chipset

IDE Int egr ated IDE Co ntro ller

SATA II Integrated Serial ATA Controller

LAN Realtek RTL 8111C

Sound ALC662

Slots

On Board

Connector

AMD Athlon 64 / Athlon 64 FX

/ Sempron / Phenom processors

Support HyperTransport 3.0

Supports up to 5.2 GT/s Bandwidth

ITE 8718F

Prov ides the most common ly used leg acy

Super I/O functionality

DDR2 DIMM Slots x 4

Max Memory Capacity 16GB

Each DIMM supports 256MB/512MB/

1GB/2GB/4GB DDR2

PCI Express Gen2 x16 slot x1 Supports PCI-E Gen2 x16 expansion cards

PCI Express Gen2 x1 slot x1 Supports PCI-E Gen2 x1 expansion cards

PCI slot x2 Supports PCI expansion cards

Floppy connector x1 Each connector supports 2 Floppy drives

IDE Conn ecto r x1 Each connector support s 2 IDE dev ice

SATA Connector x6 Each connector supports 1 SATA devices

Front Panel Connector x1 Supports front panel facilit ies

Front Audio Connector x1 Supports front panel audio function

Athlon 64 x2

AMD 64 Architecture enables 32 and 64 bit

computing

Supports Hyper Transport 3.0 and Cool=n=Quiet

Low Pin Count Interface

En v iro n ment Co ntro l init iatives

H/W Mon ito r

ITE's "S mart Guard ian" funct ion

Dual Chan ne l Mode DDR2 memo ry mod u le

Supports DDR2 533 / 667 / 800

Supports DDR2 1066 (by AM2+ CPU)

Register ed DIMM and ECC D IMM is not supported

Max Sh ared V id eo Memory is 512 MB

DX10 / HDC P / PureVideo support

Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode

supports PIO Mode 0~4,

Data transfer rates up to 3 Gb/s

SATA Version 2.0 spec ific at ion co mpliant

10 / 100 / 1000 Mb/s auto negotiation

Half / Full duplex capability

5.1 channels audio out

High Definition Audio

2

SPEC

CD-in Connector x1 Supports CD audio-in function

S/PDIF out connector x1 Supports digital audio out function

CPU Fan header x1 CPU Fan power supply (with Smart Fan function)

System Fan header x1 System Fan Po wer supply

CMOS clear header x1 Restore CMOS data to factory default

USB connector x4 Each connector supports 2 front panel USB ports

Power Connector (24pin) x1 Connects to Power supply

Power Connector (4pin) x1 Connects to Power supply

Printer Port Connector x1 Each connector supports 1 Printer port

Serial port Connector x1 Connects to RS-232 Port

PS/2 Keybo ard x1

PS/2 Mous e x1

Back Panel

I/O

Board Size 220 mm(W) x 244 mm(L)

Special

Features

OS Support Windows XP / VISTA

DVI port x1

VGA port x1

LAN port x1

USB Port x4

Audio Jack x3

RAID 0 / 1 / 5 / 0+1 support

Hyb r id SL I s uppo rt (by nV ID IA d r iver)

1.4 R

EAR PANEL CONNECTORS

GF8200 M2+

Connects to PS/2 Keyboard

Connects to PS/2 Mouse

Connect to DVI-D monitor

Connect to D-SUB monitor

Connect to RJ-45 ethernet cab le

Connect t o US B devices

Provide Audio-In/Out and microphone connection

Biostar Reserves the right to add or remove support

for any OS With or without notice.

PS/2
Mou se

PS/2
Keyboard

LAN

Line In/
Surr ound

Line Out

Mic In 1/
Bass/ Center

VGA

DVI-D

USB X2USBX2

3

Motherboard Manual

1.5 MOTHERBOARD LAYOUT

JKBM S1

VGA

DVI

JUSB1

JUS BLAN2

JAUDIO 1

JCDIN1

LAN

Codec

JATXPWR2

JAU D I OF 1

JKB_ PWR

JCFA N1

Socket AM2+

DIMMA1

DIMMA2

DIMMB1

JUSB3

JUSB4

SATA4

SATA3

JSFA N1

DIMMB2

IDE1

JUSB2

JUSBPWR2

JUSB5

JCMOS1

BIOS

SATA 6

SATA 5

JPANEL1

JUSBPWR4

JATXPWR1

GeForce

8200

PC I-E X1_1

PEX1 6_1

BAT1

Super I/O

SATA 2

SATA1

JCOM1

JSPDIF_OUT1

JPR NT1

PCI1

PCI2

FDD1

4

Note: represents the 1■

st

pin.

CHAPTER 2: HARDWARE INSTALLATION

GF8200 M2+

2.1 I

NSTALLING CENTRAL PROCESSING UNIT (CPU)

Step 1: Remove the socket protection cap.

Step 2: Pull the lever toward direction A from the socket and then raise the

lever up to a 90-degree angle.

Step 3: Look for the white triangle on socket, and the gold triangle on

CPU should point towards this white triangle. The CPU will fit only
in the correct orientation.

5

Motherboard Manual

Step 4: Hold the CPU down firmly, and then close the lever toward direct

B to complete the installation.

Step 5: Put the CPU Fan on the CPU and buckle it. Connect the CPU

FAN power cable to the JCFAN1. This completes the installation.

Note: Please update the BIOS to the latest version while using AM2+ CPUs. Due to the latest CPU

transition, you may encounter the situation that the new system failed to boot while using new
AM2+ CPUs. In this case, please install one standard AM2 CPU to boot your system, and
update the latest BIOS from our website for AM2+ CPUs support.

6

GF8200 M2+

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufact urer.
Connect the fan cable to the connector while matching the black wire to
pin#1.

JCFAN1: CPU Fan Header

1

4

JSFAN1: System Fan Header

Pin

Assignment

1 Ground
2 +12V
3

FAN RPM r at e
sense

4 Smart Fan

Control (By Fan)

Pin

Assignment

1 Ground
2 +12V
3 FAN RPM rate

sense

13

Note:

The JCFAN1 supports 4-pin head connector. The JSFAN1 supports 3-pin head
connector. When connecting with wires onto connectors, please note that the red wire is
the positive and should be connected to pi n#2, and the black wire is Ground and should

be connected to GND.

7

Motherboard Manual

2.3 INSTALLING SYSTEM MEMORY

A. Memory Modules

DIMMA2

DIMMA1

DIMMB1

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.

DIMMB2

2. Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.

8

GF8200 M2+

B. Memory Capacity

DIMM Socket

Location

DIMMA1 256MB/512MB/1GB/2GB/4GB

DIMMA2 256MB/512MB/1GB/2GB/4GB

DIMMB1 256MB/512MB/1GB/2GB/4GB

DIMMB2 256MB/512MB/1GB/2GB/4GB

DDR2 Module

Total Mem ory

Size

Max is 16GB.

C. Dual Channel Memory installation

To trigger the Dual Channel function of the motherboard, the memory module
must meet the following requirements:

Install memory module of the same density in pairs, shown in the following
table.

Dual Channel Status

Enabled O O X X

Enabled X X O O

Enabled O O O O

DIMMA1

DIMMA2

(O means memory installed, X means memory not installed.)

The DRAM bus width of the memory module must be the same (x8 or
x16)

DIMMB1

DIMMB2

9

Motherboard Manual

3

2.4 CONNECTORS AND SLOTS

FDD1: Floppy Disk Connector

The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the
provided floppy drive ribbon cable.

234

IDE1: Hard Disk Connector

The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.

The IDE connectors can connect a master and a slave drive, so you can
connect up to two hard disk drives.

13

3940

21

10

GF8200 M2+

PEX16_1: PCI-Express Gen2 x16 Slot

- PCI-Express 2.0 compliant.

- Maximum theoretical realized bandwidth of 8GB/s simultaneously per

direction, for an aggregate of 16GB/s totally.

PCI-EX1_1: PCI-Express Gen2 x1 Slot

- PCI-Express 2.0 compliant.

- Data transfer bandwidth up to 500MB/s per direction; 1GB/s in total.

- PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.

- 2X bandwidth over the PCI-Express 1.0 architecture.

PCI -EX1 _1

PE X16_1

PCI1/PCI2: Peripheral Component Interconnect Slots

This motherboard is equipped with 2 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.

PCI1

PCI 2

11

Motherboard Manual

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 H

OW TO SETUP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SETTINGS

JPANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.

PWR_LED

On/Off

-

9
1

++

SPK

HLED

16

8

-

+

RST

12

Pin Assignment Function Pin Assignment Function

1 +5V 9 N/A
2 N/A 10 N/A
3 N/ A 11 N/ A N/ A
4 Speaker
5 HDD LED (+) 13 Power LED (+)
6 HDD LED (-)
7 Ground 15 Power button
8 Reset control

Speaker
Connector

Hard drive
LED

Reset button

12 Power LED (+)

14 Power LED (-)

16 Ground

N/A

Power LED

Power-on button

GF8200 M2+

JATXPWR1: AT X P ower Source Connector

This connector allows user to connect 24-pin power connector on the ATX
power supply.

12

1

13

24

Pin Assignment Pin Assignm ent

13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 Ground 3 Ground
16 PS_ON 4 +5V
17 Ground 5 Ground
18 Ground 6 +5V
19 Ground 7 Ground
20 NC 8 PW_OK
21 +5V 9 Standby Voltage+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 Ground 12 +3.3V

JATXPWR2: AT X P ower Source Connector

By connecting this connector, it will provide +12V to CPU power circuit.

12

34

Pin

Assignment

1 +12V
2 +12V
3 Ground
4 Ground

Note:

Before power on the system, please make sure that both JATXPWR1 and JATXPWR2
connectors have been plugged-in.

13

Motherboard Manual

JUSB2~JUSB5: Headers for USB 2.0 Ports at Front Panel

These headers allow user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.

JUSB2
JUSB3
JUSB4
JUSB5

19

210

SATA1~SATA6: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 6 channels SATA interface,
it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.

SATA2 SATA4 SATA6
SATA1 SATA3 SATA5

Assignment

Pin

1 +5V (fused)
2 +5V (fused)
3 USB­4 USB­5 USB+
6 USB+
7 Ground
8 Ground
9 NC

10 Key

Assignment

Pin

1 Ground
2 TX+
3 TX­4 Ground
5 RX­6 RX+
7 Ground

14

14

7

Note:

Due to the chipset's specification, SATA5 and SATA6 do not support SATA mode, only
support AHCI+RAID mode.

GF8200 M2+

JSPDIF_OUT1: Digital Audio-out Connector

This connector allows user to connect the PCI bracket SPDIF output header.

Pin

Assignment

1 +5V
2 SPDIF_OUT
3 Ground

13

JAUDIOF1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front
panel. This header allows only HD audio front panel connector; AC’97 connector
is not acceptable.

Pin Assignment

1 Mic Left in
2 Ground
3 Mic Right in
4 GPIO
5 Right line in
6 Jack Sense
7 Front Sense
8 Key
9 Left line in

210

10 Jack Sense

19

15

Motherboard Manual

JCDIN1: CD-ROM Audio-in Connector

This connector allows user to connect the audio source from the variaty devices,
like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc.

JCMOS1: Clear CMOS Header

By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting
and the CMOS data, please carefully follow the procedures to avoid damaging
the motherboard.

14

Pin 1-2 Close:

Normal Operation
(default).

13

Pin 2-3 Close:

Clear CMOS data.

Assignment

Pin

1 Left Channel

Input
2 Ground
3 Ground
4 Right Channel

Input

13

13

16

※ Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Reset your desired password or clear the CMOS data.

GF8200 M2+

JPRNT1: Printer Port Connector

This header allows you to connector printer on the PC.

2

125

Pin Assignment Pin Assignment

1 -Strobe 14 Ground
2 -ALF 15 Data 6
3 Data 0 16 Ground
4 -Error 17 Data 7
5 Data 1 18 Ground
6 -Init 19 -ACK
7 Data 2 20 Ground
8 -Scltin 21 Busy

9 Data 3 22 Ground
10 Ground 23 PE
11 Data 4 24 Ground
12 Ground 25 SCLT
13 Data 5 26 Key

JCOM1: Serial port Connecto r

The motherboard has a Serial Port Connector for connecting RS-232 Port.

Pin

Assignment

1 Carrier detect
2 Received data
3 Transmitted data
4 Data terminal ready
5 Signal ground
6 Data set ready
7 Request to send

210

19

8 Clear to send
9 Ring indicator

10 NC

17

Motherboard Manual

JUSBPWR4/JUSBPWR2: Power Source Headers for USB Ports

Pin 1-2 Close:

JUSBPWR4: +5V for USB ports at JUSB1/JUSBLAN2.
JUSBPWR2: +5V for USB ports at front panel (JUSB2~JUSB5).

Pin 2-3 Close:

JUSBPWR4: +5V STB for USB ports at JUSB1/JUSBLAN2.
JUSBPWR2: +5V STB for USB ports at front panel (JUSB2~JUSB5).

JUSBPWR4

1

3

1

3

Pin 1-2 close

3

1

JUSBPWR2

1

3

Pin 2-3 close

JKB_PWR: Power Source Header for PS/2 Keyboard and Mouse

1

3

+5V for PS/2 keyboard and
mouse.

+5V STB for PS/2 keyboard
and mouse.

1

3

Pin 1-2 close

1

3

Pin 2-3 close

18

CHAPTER 4: RAID FUNCTIONS

GF8200 M2+

4.1 O

z Supports Windows XP Home/Professional Edition, and Windows Vista.

PERATION SYSTEM

4.2 RAID ARRAYS

RAID supports the following types of RAID arrays:

RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for

many applications.

RAID 1: RAID 1 defines techniques for mirroring data.
RAID 0+1: RAID 0+1 combines the techniques used in R AID 0 and RAID 1.
RAID 5: RAID 5 provides fault to lerance and better utilization of disk capacity.

4.3 HOW RAID WORKS

RAID 0:

The controller “stripes” data across multip le drives in a RAID 0 array system. It breaks
up a large file into smaller b locks and performs disk reads and writes across multiple
drives in parallel. The size of each block is determined by the stripe size parameter,
which you set during the creation of the RAID set based on the system environment.
This technique reduces overall disk access time and offers high bandwidth.

Features and Benefits

- Drives: Minimum 2, and maximum is up to 6 or 8. Depending on the
platform.

- Uses: Intended for non-critical data requiring high data throughput, or any
environment that does not require fault tolerance.

- Benefits: provides increased data throughput, especially for large files.
No capacity loss penalty for parity.

- Drawbacks: Does not deliver any fault tolerance. If any drive in the array
fails, all data is lost.

- Fault Tolerance: No.

Block 1
Block 3
Block 5

Block 2
Block 4
Block 6

19

Motherboard Manual

RAID 1:

Every read and write is actually carr ied out in parallel across 2 disk drives in a RAID 1
array system. The mirrored (backup) copy of the data can reside on the same disk or on
a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if
the active volume or drive is corrupted or becomes unavailable because of a hardware
failure.

RAID techniques can be applied for high-ava ilability solutions, or as a form of
automatic backup that eliminates tedious manual backups to more expensive and less
reliable media.

Features and Benefits

- Drives: Minimum 2, and maximum is 2.

- Uses: RAID 1 is ideal for small databases or any other application that

requires fault tolerance and minimal capacity.

- Benefits: Provides 100% data redundancy. Should one drive fail, the
controller switches to the other drive.

- Drawbacks: Requires 2 drives for the storage space of one drive.
Performance is impaired during drive rebuilds.

- Fault Tolerance: Yes.

20

Block 1
Block 2
Block 3

Block 1
Block 2
Block 3

GF8200 M2+

RAID 0+1:

RAID 0 drives can be mirrored usin g RAID 1 techniques. Resulting in a RAID 0+1
solution for improved performance plus resiliency.

Features and Benefits

- Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.

- Benefits: Optimizes for both fault tolerance and performance, allowing for

automatic redundancy. May be simultaneously used with other RAID
levels in an array, and allows for spare disks.

- Drawbacks: Requires twice the available disk space for data redundancy,
the same as RAID level 1.

- Fault Tolerance: Ye s .

GeForce

8200

Block 1
Block 3
Block 5

Block 2
Block 4
Block 6

Block 1
Block 3
Block 5

Block 2
Block 4
Block 6

21

Motherboard Manual

RAID 5:

RAID 5 stripes both data and parity information across three or more drives. It writes
data and parity blocks across all the drives in the array. Fault tolerance is maintained
by ensuring that the parity informat ion for any given block of data is placed on a
different drive from those used to store the data itself.

Features and Benefits

- Drives: Mi nimu m 3.

- Uses: RAID 5 is recommended for transaction processing and general

purpose service.

- Benefits: An ideal combination of good performance, good fault tolerance,
and high capacity and storage efficiency.

- Drawbacks: Individual block data transfer rate same as a single disk.
Write performance can be CPU intensive.

- Fault Tolerance: Ye s .

Disk 1

DATA 1

DATA 3

PARIT Y

DATA 7
DATA 9

PARIT Y

Disk 2

GeForce

8200

DATA 2

PARIT Y

DATA 5
DATA 8

PARIT Y
DATA 11

Disk 3

PARIT Y

DATA 4
DATA 6

PARIT Y
DATA 10
DATA 12

※ For more detailed setup information, please refer to the Driver CD, or go to

http://www.nvidia.com/object/IO_28159.html to download the NVIDIA RAID User’s Guide.

22

CHAPTER 5: USEFUL HELP

GF8200 M2+

5.1 D

RIVER INSTALLATION NOTE

After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.

You will see the following window after you insert the CD

The setup guide will auto detect your motherboard and operating system.

Note:

If this window didn’t show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation

To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.

B. Software Installation

To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.

C. Manual

Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.

Note:

You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader so ftware from
http://www.adobe.com/products/acrobat/readstep2.html

23

Motherboard Manual

e

5.2 SOFTWARE

Installing Software

1. Insert the Setup CD to the optical drive. The drivers installation program
would appear if the Autorun function has been enabled.

2. Select Software Installatio n, and then click on the respective software
title.

3. Follow the on-screen instructions to complete the installation.

Launching Software

After the installation process, you will see the software icon “eHOT Line” /
“BIOS Update” appears on the desktop. Double-click the icon to launch the
utility.

eHot-Line (Optional)

eHot-Line is a convenient utility that helps you to contact with our
Tech-Support system. This utility will collect the system information which is
useful for analyzing the problem you may have encountered, and then send
these information to our tech-support department to help you fix the problem.

Before you use this uti lity, please set Outlook Express as yo ur default e-mail clie nt application program.

re pr es ent s im por ta nt

*

information that you
must provide. Without
this inf ormation, you may
not be able to send out
the mail.

This block will show
the information which
would be collected in
the mail.

Describe condition

*

of your system.

Select your area or

*

the area cl os e to you.

Provide the e-mail
address that you would
like to s end the copy to.

Pr ovid e the na me of

*

the memor y module
manufacturer.

Provide the name of
th e powe r su ppl y
manufacturer and the
model no.

Se nd th e mai l out .

Sav e the se infor ma tion to a .t xt fil

Exit this dialog.

24

GF8200 M2+

After filling up this informatio n, click “Send”
to send the mail out. A warning dialog would
appear asking for your confirmation; click

“Send” to confirm or “Do Not Send” to cancel.

If you want to save this information to a .txt file, click “Save As…” and then you
will see a saving dialog appears asking you to enter file name.

Enter the file name and then click
“Save”. Your system information

will be saved to a .txt file.

Open the saved .txt file, you will see
your system information including
motherboard/BIOS/CPU/video/
device/OS information. This
information is also concluded in the
sent mail.

We will not share customer ’s data with any other third parties,
so please feel free to provide your system information while using
eHot-Line service.

If you are not using Outlook Express as your default e-mail client
application, you may need to save the system information to a .txt file
and send the file to our tech support with other e-mail application.
Go to the following web

http://www.biostar.com.tw/app/en-us/about/contact.php for getting

our contact information.

25

Motherboard Manual

BIOS Update

BIOS Update is a convenient utility which allows you to update your
motherboard BIOS under Windows system.

AWARD BIOS AMI BIOS

Clear CMOS function

(Only for AWARD BIOS)

Show current BIOS information

Save cur rent B IOS

to a .bin file

Update BIOS

with a BIOS file

<Backup BIOS>

Once click on this button, the saving
dialog will show. Choose the
position to save file and enter file
name. (We recommend that the file
name should be English/number
and no longer than 7 characters.)
Then click Save.

26

After the saving process, finish
dialog will show. Click on OK to

complete the BIOS Backup
procedure.

GF8200 M2+

<Update BIOS>

Before doing this, please download the proper BIOS file from the website.

For AWARD BIOS, update BIOS procedure
should be run with Clear CMOS function, so
please check on Clear CMOS first.

Then click Update BIOS button, a
dialog will show for asking you backup
current BIOS. Click Yes for BIOS
backup and refer to the Backup BIOS
procedure; or click No to skip this
procedure.

After the BIOS Backup procedure, the
open dialog will show for requesting the
BIOS file which is going to be updated.
Please choose the proper BIOS file for
updating, then click on Open.

The utility will update BIOS with the
proper BIOS file, and this process may
take minutes. Please do not open any
other applications during this process.

After the BIOS Update process, click on
OK to restart the system.

While the system boots up and the full screen logo shows, press <Delete>
key to enter BIOS setup.

In the BIOS setup, use the Load Optimized Defaults function and then Save and
Exit Setup to exit BIOS setup. BIOS Update is completed.

All the information and content above about the software are subject to be changed
without notice. For better performance, the software is being co ntinuously updated.
The information and pictures described above are for your reference only. The actual
information and settings on board may be slightly different from this manual.

27

Motherboard Manual

5.3 EXTRA INFORMATION

CPU Overheated

If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.

When the CPU is over heated, the motherboard will shutdow n
automatically to avoid a damage of the CPU, and the system may not
power on again.

In this case, please double check:

1. The CPU cooler surface is placed evenly with the CPU surface.

2. CPU fan is rotated normally.

3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU protection
function.

1. Remove the power cord from power supply for seconds.

2. Wait for seconds.

3. Plug in the power cord and boot up the system.

Or you can:

1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)

2. Wait for seconds.

3. Power on the system again.

28

BIO-Flasher

BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to
update your BIOS via USB pen drive or floppy disk.

The BIO-Flasher is built in the BIOS chip. To enter the utility, press <F12>
during the Power-On Self Tests (POST) procedure while booting up.

Updating BIOS with BIO-Flasher

1. Go to the website to download the latest BIOS file for the motherboard.

2. Then, save the BIOS file into a USB pen drive or a floppy disk.

3. Insert the USB pen drive or the floppy disk that contains the BIOS file to the
USB port or the floppy disk drive.

4. Power on or reset the computer and then
press <F12> during the POST process.
A select dialog as the picture on the right
appears.
Select the device contains the BIOS file and
press <Enter> to enter the utility.

GF8200 M2+

5. The utility will show the BIOS
files and their respective
information. Select the proper
BIOS file and press <Enter>
then <Y> to perform the BIOS
update process.

6. After the update process, the utility will ask you to reboot the system.
Press <Y> to proceed. BIOS update completes.

z This utility only allows storage device with FAT32/16 format and single

parti tion.

z Shutting down or resetting the system while updating the B IOS will lead to

system boot failure.

29

Motherboard Manual

5.4 AMI BIOS BEEP CODE

Boot Block Beep Codes

Number of Beeps Description

1 No media present. (Insert diskette in floppy drive A:)

2

3 Insert next diskette if multiple diskettes are used for recovery
4 Flash Programming successful
5 File read error

7 No Flash EPROM detected
10 Flash Erase error
11 Flash Program error
12 “AMIBOOT.ROM” file size error

13

POST BIOS Beep Codes

Number of Beeps Description

1 Memory refresh timer error

3 Base memory read/write test error

6 Keyboard controller BAT command failed

7 General exception error (processor exception interrupt error)

8 Display memory error (system video adapter)

“AMIBOOT.ROM” file not found in root directory of diskette in
A:

BIOS ROM image mismatch (file layout does not match
image present in flash device)

Troubleshooting POST BIOS Beep Codes

Number of Beeps Troubleshooting Action

1, 3 Reseat the memory, or replace with known good modules.

Fatal error indicating a serious problem with the system.
Consult your system manufacturer. Before declaring the
motherboard beyond all hope, eliminate the possibility of
interference by a malfunctioning add-in card. Remove all
expansion cards except the video adapter.

6, 7

8

30

z If beep codes are generated when all other expansion

cards are absent, consult your system manufacturer’s
technical support.

z If beep codes are not generated when all other expansion

cards are absent, one of the add-in cards is causing the
malfunction. Insert the cards back into the system one at a
time until the problem happens again. This will reveal the
malfunctioning card.

If the system video adapter is an add-in card, replace or
reseat the
video adapter. If the video adapter is an integrated part of the
system board, the board may be faulty.

5.5 TROUBLESHOOTING

Probable Solution

1. No power to the system at all
Power light don’t illuminate, fan
inside power supply does not turn
on.

2. Indicator light on keyboard does
not turn on.

System inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drive is spinning.

System does not boot from hard disk
drive, can be booted from optical drive.

System only boots from optical drive.
Hard disk can be read and applications
can be used but booting from hard disk
is impossible.

Screen message says “Invalid
Configuration” or “CMOS Failure.”

Cannot boot system after installing
second hard drive.

GF8200 M2+

1. Make sure power cable is
securely plugged in.

2. Replace cable.

3. Contact technical support.

Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.

1. Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.

2. Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.

1. Back up data and applications
files.

2. Reformat the hard drive.
Re-install applications and data
using backup disks.

Review system’s equipment. Make sure
correct information is in setup.

1. Set master/slave jumpers
correctly.

2. Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.

31

Motherboard Manual

APPENDENCIES: SPEC IN OTHER LANGUAGE

G

ERMAN

Sp ezif ika tio nen

Sockel AM2+

CPU

FSB

Chipsatz GeForce 8200

Super E/A

Arbeitsspeich

er

Grafik Integrierter GeForce 8200-Chipsatz

IDE Integ r iert er IDE - Cont rolle r

SATA Integrierter Serial ATA-Controller

LAN Realtek RTL 8111C

HD

Audio-Unters

tützung

Steckplätz e

AMD Athlon 64 / Ath lon 64 FX / Althlon 64

X2 / S empron / Phenom Proz esso ren

Unterstützt HyperTransport 3.0 mit einer

Bandbreite von bis zu 5.2 GT/s

ITE8718F

Biet et die h äuf ig v er wend eten alten Super

E/A-Funktionen.

DDR2 DIMM-Steckplätze x 4

Max. 16GB Arbeitsspeicher

Jeder DIMM unterstützt 256MB/512MB/

1GB/2GB/4GB DDR2.

ALC662

PCI Express Gen2 x16 Steckplatz x1

PCI Express Gen2 x1 Steckplatz x1

PCI-Steckplatz x 2

32

Die AMD 64-Architektur unterstützt eine 32-Bit- und

64-Bit-Datenverarbeitung

Unterstützt Hyper Transport 3.0 und Cool’n’Quiet

Low Pin Count-Schnittstelle

Umgebungskontrolle,

Hardware-Überwachung

"Smart Guardian"-Funktion von ITE

Dual-Kanal DDR2 Speichermodul

Unterstützt DDR2 533 / 667 / 800

Unterstützt DDR2 1066 (by AM2+ CPU)

registrierte DIMMs. ECC DIMMs werden nicht

unterstützt.

Max. 512MB gemeinsam benutzter Videospeicher

Unterstützt DX10 / HDCP / PureVideo

Ultra DMA 33 / 66 / 100 / 133 Bus Master-Modus

Unterstützt PIO-Modus 0~4,

Datentransferrate b is zu 3 Gb /s

Konform mit der SATA-Spezifikation Version 2.0.

10 / 100 / 1000 Mb/s Auto-Negotiation

Halb-/ Vollduplex-Funktion

5.1-Kanal-Audioausgabe

Unterstützt High-Definition Audio

Onboard-Ans

chluss

Rückseiten-E

/A

Platinengröß

e

Sonderfunkti

onen

OS-Unterstü

tzung

GF8200 M2+

Sp ezif ika tio nen

Diskettenlaufwerkanschluss x1 Jeder Anschluss unterstützt 2 Diskettenlaufwerke

IDE-Anschluss x1 Jeder Anschluss unterstützt 2 IDE-Laufwerke

SATA-Anschluss x6 Jeder Anschluss unterstützt 1 SATA-Laufwerk

Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen

Front-Audioanschluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion

CD-IN-Anschluss x1 Unterstützt die CD Audio-In-Funktion

S/PDIF- Ausgangsanschluss x1 Unterstützt die digitale Audioausgabefunktion

CPU-Lüfter-Sockel x1

System-Lüfter-Sockel x1 System-Lüfter-Stromversorgungsanschluss

"CMOS löschen"-Sockel x1

USB-Anschluss x4

Stromanschluss (24-polig) x1

St romansch luss (4-po l ig ) x1

Druckeranschluss Anschluss x1 Jeder Anschluss unterstützt 1 Druckeranschluss

Serieller Anschluss x1

PS/2-Tastatur x1

PS/2-Maus x1

VGA-Anschluss x1

LAN-Anschluss x1

USB-Anschluss x4

Audioanschluss x3

DVI-Anschluss x1

220 mm (B) X 244 mm (L)

Unterstützt RAID 0 / 1 / 5 / 0+1

Unterstützt Hybrid SLI (by nVIDIA driver)

Windows XP / VISTA

CPU-Lüfterstromversorgungsanschluss (mit Smart

Fan -F un ktio n)

Jeder Anschluss unterstützt 2

Fronttafel-USB-Anschlüsse

Biostar behält s ich das Recht vor, ohne An kündigung

die Unterstützung für ein Betriebssystem

hinzuzufügen oder zu entfernen.

33

Motherboard Manual

FRANCE

SPEC

Socket AM2+

UC

Bus frontal

Chipset GeForce 8200

Super E/S

Mémoire

principale

Graphiques Integré dans la chipset GeForce 8200

IDE Contrôleur IDE intégré

SATA

LAN Realtek RTL 8111C

Prise en

charg e

aud io HD

Fentes

Connecteur

embarqu é

Processeurs AMD Athlon 64 / Athlon 64 FX

/ Alth lon 64 X2 / S empron / Pheno m

Prend en charge Hyp er Trans port 3.0

jusqu'à une bande passante de 5.2 GT/s

ITE 8718F

Fournit la fonctionnalité de Super E/S

patrimoniales la plus utilisée.

Fentes DDR2 DIM M x 4

Capacité mé mo ir e max imal e de 16 Go

Chaque DIMM prend en charge des DDR2

de 256Mo/512 Mo/1Go /2Go/4Go

Contrô leur Serial ATA int é gr é

ALC662

Fente PCI Express Gen2 x16 x1

Fente PCI Express Gen2 x1 x1

Fente PCI x2

Connecteur de disquette x1

Connecteur IDE x1

Connecteur SATA x6

L'architecture AMD 64 permet le calcul 32 et 64 bits

Prend en cha rge Hyp er Transport 3.0 et Coo l’n’Qu iet

Int e rfa ce à f a ib le co mpte d e b roches

Initiatives de contrôle environnementales,

Mon iteur d e mat ériel

Fonction "Gardien intelligent" de l'ITE

Modu le d e mémo ir e DDR 2 à mod e à d oub le vo ie

Prend en charge la DDR2 533 / 667 / 800

Prend en charge la DDR2 1066 (by AM2+ CPU)

Les DIMM à registres et DIMM avec code correcteurs

d'erreurs ne sont pas prises en charge

Mémoire vidéo partagée maximale de 512 Mo

Prise en charg e DX10 / HDC P / Pur eV ideo

Mode principale de Bus Ultra DMA 33 / 66 / 100 / 133

Prend en charge le mode PIO 0~4,

Taux de transfert jusqu'à 3 Go/s.

Co nfo rme à la spécif icat ion SATA Vers io n 2. 0

10 / 100 / 1000 Mb/s négociation automatique

Half / Full duplex capability

Sortie aud io à 5 .1 vo ies

Prise en charg e de l'aud io haut e définit ion

Chaque connector prend en charge 2 lecteu rs de

disquettes

Chaque connect eur prend en ch arge 2 périphériques

IDE

Chaque connect eur prend en ch arge 1 périphérique

SATA

34

Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant

Connecteur Audio du panneau avant x1 Prend en charge la fonct ion audio du panneau avant

Connecteur d'entrée CD x 1 Prend en cha rge la fonction d'entrée audio de CD

Connecteur de sortie S/PDIF x1 Prend en charge la fonction de sortie audio numérique

Embase de ventilateur UC x1

Embase de ventilateur système x1 Alimentation électrique du ventilateur système

Embase d'effacement CMOS x1

Connecteur USB x4

Connecteur d'aliment at ion x1

(24 broches)

Connecteur d'aliment at ion x1

(4 broch es)

Connecteur de Port d'imprimante x1

Connecteur de Port série x1

Clavier PS/2 x1

Souris PS/2 x1

E/S du

panneau

arrière

Dimension

s de la

cart e

Fonctionnal

ité s

spéciales

Support SE Windows XP / VISTA

Port VGA x1

Port LAN x1

Port USB x4

Fiche aud io x3

Port DVI x 1

220 mm (l) X 244 mm (H)

Prise en charg e RA ID 0 / 1 / 5 / 0+1

Pr is e en ch arg e Hyb r id SL I (b y n V IDIA

driver)

GF8200 M2+

SPEC

Alimentation électrique du ventilateur UC (avec

fonction de ventilateur intelligent)

Chaque connecteur prend en charge 2 ports USB de

panneau avant

Chaque connector prend en charge 1 Port

d'imprimante

Biostar se réserve le droit d'ajouter ou de supprimer le

support de SE avec ou sans préavis.

35

Motherboard Manual

ITALIAN

SPECIFICA

Socket AM2+

CPU

FSB

Chipset GeForce 8200

Super I/O

Memoria

principale

Grafica Integrata nel Chipset GeForce 8200

IDE Cont roller IDE integrato

SATA Controller Serial ATA integrato

LA N Realtek RTL 8111C

Supporto

audio HD

Allo g gi

Connettori

su scheda

Processori AMD Athlon 64 / Athlon 64 FX

/ Althlon 64 X2 / Sempron / Phenom

Supporto di HyperTransport 3.0 fino a

5.2 GT/s di larghezza di banda

ITE 8718F

Fo rnis ce le fun z ionalit à leg a cy Sup er

I/O usate più comunemente.

Alloggi DIMM DDR2 x 4

Capacità massima della memoria 16GB

Ciascun DIMM supporta DDR2

256MB/512MB/1GB/2GB/4GB

ALC662

Alloggio PCI Express Gen2 x16 x1

Alloggio PCI Express Gen2 x1 x1

Allo g gio PC I x 2

Connettore floppy x1 Ciascun connettore supporta 2 unità Floppy

Connettore IDE x1 Ciascun connettore supporta 2 unità IDE

Connettore SATA x6 Ciascun connettore supporta 1 unità SATA

Co nnettore pannello fro ntale x 1 Sup po rta i servizi del pannello fro ntale

L’archit et t ura A MD 64 ab ilita la co mpu t az io ne 32

e 64 bit

Supporto di Hyper Transport 3.0 e Cool’n’Quiet

Interfaccia LPC (Low Pin Count)

Funzioni di controllo dell’ambiente:

Monitoraggio hardware

Funzione "Smart Guardian" di ITE

Modulo di memoria DDR2 a canale doppio

Supporto di DDR2 533 / 667 / 800

Supporto di DDR2 1066 (by AM2+ CPU)

DIMM registrati e DIMM ECC non sono supportati

La memoria video condivisa massima è di 512 MB

Supporto DX10 / HDCP / PureVideo

Modalità Bus Master Ultra DMA 33 / 66 / 100 /

133

Supporto modalità PIO Mode 0-4

Velocità di trasferimento dei dati fino a 3 Gb/s.

Co mp at ibile specifi ch e S ATA Vers io ne 2.0.

Negoziazione automatica 10 / 100 / 1000 Mb/s

Capacità Half / Full Duplex

Uscita audio 5.1 canali

Supporto audio High-Definition (HD)

36

I/O

pannello

posteriore

Dimension

i scheda

Caratterist

iche

speciali

Sistemi

operat ivi

supportati

GF8200 M2+

SPECIFICA

Connettore audio frontale x1 Supporta la funzione audio pannello frontale

Connettore CD-in x1 Supporta la funzione input audio CD

Connettore output SPDIF x1 Supporta la funzione d’output audio digitale

Co llett o re vent o lina C PU x 1

Co llett o re vent o lina sistema x1 Aliment az io n e vento lina d i s is t ema

Co llett o re cancellaz ione CMOS x 1

Connettore USB x4

Connettore alimentazione x1

(24 pin)

Connettore alimentazione x1

(4 pin)

Connettore Porta stampante x1 Ciascun connettore supporta 1 Porta stampante

Connettore Porta s eriale x 1

Tas t iera P S /2 x 1

Mou s e PS/2 x 1

Porta VGA x1

Porta LAN x1

Porta USB x4

Connettore audio x3

Porta DVI x1

220 mm (larghezza) x 244 mm

(altez za)

Supporto RAID 0 / 1 / 5 / 0+1

Su pporto Hyb rid S LI (by nVID IA

driver)

Windows XP / VISTA

Alimentazione ventolina CPU (con funzione Smart

Fan)

Ciascun connettore supporta 2 porte USB

pannello frontale

Biostar si riserva il diritto di aggiungere o

rimuovere il supporto di qualsiasi sistema

operativo senza preavviso.

37

Motherboard Manual

SPANISH

Conector AM2+

CPU

FSB

Conjunto

de chips

Súper E/S

Memoria

principal

Gráficos

IDE Controlador IDE integrado

SATA Controlador ATA Serie Integrado

Red Local Realtek RTL 8111C

Soporte de

sonido HD

Ranuras

Conectores

en p laca

Procesadores AMD Athlon 64 / Athlon 64

FX / Athlon 64 X2 / Sempron / Phenom

Admite HyperTransport 3.0 con un ancho

de banda de hasta 5.2 GT/s

GeForce 8200

ITE 8718F

Le ofrece las funcionalidades heredadas

de uso más común Súper E/S.

Ranuras DIMM DDR2 x 4

Capacidad máxima de memoria de 16GB

Cada DIMM admite DDR de 256MB/

512MB/1GB/2GB/4GB

Integrados en el conjunto de chips

GeForce 8200

ALC662

Ranura PCI Express Gen2 x16 X1

Ranura PCI Express Gen2 x1 X1

Ranura PCI X2

Conector disco flexible X1 Cada conector soporta 2 unidades de disco flexible

Conector IDE X1 Cada conector soporta 2 dispositivos IDE

Conector SATA X6 Cada conector soporta 1 dispositivos SATA

Especificación

La arquitectura AMD 64 permite el procesado de 32 y

64 bits

Soporta las tecnologías Hyper Transport 3.0 y

Cool’n’Quiet

Interfaz de cuenta Low Pin

In iciat ivas de co ntro l d e ent orn o ,

Monitor hardware

Función "Guardia inteligente" de ITE

Módulo de memoria DDR2 de canal Doble

Admite DDR2 de 533 / 667 / 800

Admite DDR2 de 1066 (by AM2+ CPU)

No admite DIMM registrados o DIMM compatibles con

ECC

Memoria máxima de vídeo compartida de 512 MB

Admite DX10 / HDCP / Pu reV ideo

Modo bus maestro Ultra DMA 33 / 66 / 100 / 133

Soporte los Modos PIO 0~4,

Tasas de transferencia de hasta 3 Gb/s.

Co mp at ible con la ve rsión S ATA 2.0 .

Negociación de 10 / 100 / 1000 Mb/s

Funciones Half / Full dúplex

Salida de sonido de 5.1 canales

Soporte de sonido Alta Definición

38

Panel

trasero de

E/S

Ta mañ o d e

la placa

Funciones

especiales

Soporte de

sistema

operativo

GF8200 M2+

Especificación

Co nect o r de p an e l f ront a l X1 S o port a in s talacion es en e l pan e l front a l

Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal

Conector de entrada de CD X1 Soporta función de entrada de sonido de CD

Conector de salida S/PDIF X1 Soporta función de salida de sonido digital

Cabecera de ventilador de CPU X1 Fuente de alimentación de ventilador de CPU (con

función Smart Fan)

Cabecera de ventilador de sistema X1 Fuente de alimentación de ventilador de sistema

Cabecera de borrado de CMOS X1

Conector USB X 4 Cada conector sopo rta 2 puertos USB frontales

Conector de alimentación X1

(24 patillas)

Conector de alimentación X1

(4 patillas)

Conector Puerto de impresora X1 Cada conector soporta 1 Puerto de impresora

Conector Puerto serie X1

Tec lad o P S /2 X1

Ratón PS/2 X1

Puerto VGA X1

Puerto de red local X1

Puert o USB X4

Conector de sonido X3

Puert o DV I X1

220 mm. (A) X 244 Mm. (H)

Admite RAID 0 / 1 / 5 / 0+1

Ad m it e Hybr id SLI (by nV ID IA dr iver )

Windows XP / VISTA

Biostar se reserva el derecho de añadir o retirar el

soporte de cualquier SO con o sin aviso previo.

39

Motherboard Manual

/

PORTUGUESE

ESPECIFICAÇÕES

Socket AM2+

CPU

FSB

Chipset GeForce 8200

Especificaç

ão Super

I/O

Memória

principal

Placa

gráf ica

IDE Controlador IDE integrado

SATA Controlador Serial ATA integrado

LAN Realtek RTL 8111C

Suporte

para áudio

de alta

definição

Ranhuras

Conectores

na placa

Processadores AMD Athlon 64

FX / A lthlon 6 4 X2 / S emp ro n / Phenom

Suporta a tecnologia HyperTransport 3.0

com u ma largura d e banda at é 5. 2 GT/s

ITE 8718F

Proporciona as funcionalidades mais

utilizadas em termos da especificação

Super I/O.

Ranhuras DIMM DDR2 x 4

Capacidad e máx ima d e memór ia: 16 GB

Cada módulo DIMM suporta uma

memória DDR2 de 256 MB/512MB/

1GB/2GB/4GB

Integrada no chipset GeForce 8200

ALC662

Ranhura PCI Express Gen2 x16 x1

Ranhura PCI Express Gen2 x1 x1

Ranhura PCI x2

Conector da unidade de disquetes x1 Cada conector suporta 2 unidades de disquetes

Conector IDE x1 Cada conector suporta 2 disposit ivos IDE

Conector SATA x6 Cada conector suporta 1 dispositivo SATA

Conector do painel frontal x1 Para suporte de várias funções no painel frontal

Athlon 64

A arquitectur a A MD 64 permite uma co mputaç ão de

32 e 64 bits

Suporta as tecno logias Hyper Trans port 3.0 e

Cool’n’Quiet

Interface LPC (Low Pin Count).

In iciat ivas par a contr o lo do a mb ient e

Monitorização do hardware

Função "S mart Gu ard ian" da ITE

Módulo de memória DDR2 de canal duplo

Suporta módulos DDR2 533 / 667 / 800

Suporta módulos DDR2 1066 (by AM2+ CPU)

Os módulos DIMM registados e os DIMM ECC não são

suportados

Memória de vídeo máxima partilhada: 512 MB

Suporta as funções DX10 / HDC P / PureV ideo

Modo Bus master U ltra DMA 33 / 66 / 100 / 133

Suporta o modo PIO 0~4,

Velocidades de transmissão de dados até 3 Gb/s.

Compat ibilidade co m a espec ificação S ATA ve rs ão 2.0.

Auto negociação de 10 / 100 / 1000 Mb/s

Capacidade semi/full-duplex

Saída de áudio de 5.1 canais

Suporta a especificação High-Definition Audio

40

Entradas/S

aídas no

painel

traseiro

Tamanho

da placa

Característi

cas

especiais

Sistemas

operativos

suportados

GF8200 M2+

ESPECIFICAÇÕES

Conector de áud io fronta l x1 Suporta a função de áud io no painel frontal

Conector para entrada d e CDs x1 Suporta a entr ada de áud io a p artir de CDs

Conector de saíd a S/PD IF x1 Suport a a saída de áudio d ig ita l

Conector da ventoinha da CPU x1

Conector da ventoinha do s istema x1 Alimentação da ventoinha do s istema

Conector para limpeza do CMOS x1

Conector USB x4 Cada conector suporta 2 portas USB no painel frontal

Conector de alimentação x1

(24 pinos)

Conector de alimentação x1

(4 p inos)

Conector da para impressora x1 Cada conector suporta 1 Porta para impressora

Conector da Porta série x1

Tec lad o P S /2 x 1

Rato PS/2 x1

Porta VGA x1

Porta LAN x1

Porta USB x4

Tomada de áudio x3

Porta DVI x 1

220 mm (L) X 244 mm (A)

Suporta as funções RA ID 0 / 1 / 5 / 0+1

Su po rta as fun çõ es H ybr id SL I (by nV IDIA

driver)

Windows XP / VISTA

Alimentação da ventoinha da CPU (com a função

Smart Fan)

A Biostar reserva-se o direito de adicionar ou remover

suporte para qualquer sistema operativo com ou sem

av is o pr év io.

41

Motherboard Manual

POLISH

SPEC

Socket AM2+

Procesor

FSB

Chipset GeForce 8200

Pamięć

główna

Super I/O

Grafika Zintegrowana w chipsecie GeForce 8200

IDE Zintegrowany kontroler IDE

SATA Zintegrowany kontroler Serial ATA

LAN Realtek RTL 8111C

Obsługa

aud io HD

Gniazda

Złącza

wbud owan

e Złącze S ATA x6 Każde złącze obs ługuje 1 urządzenie SATA

AMD Athlon 64 / Athlon 64 FX / A lthlon 64

X2 / Sempron / Phenom Procesory

Obsługa HyperTransport 3.0 o szerokości

pasma do 5.2 GT/s

Gniazda DDR2 DIMM x 4

Maks. wielkość pamięci 16GB

Każde gniazdo DIMM obs ługuje moduły

256MB/512MB/1GB/2GB/4GB DDR2

ITE 8718F

Zapewnia najbardziej powszechne

funkcje Super I/O.

ALC662

Gniazdo PCI Express Gen2 x16 x1

Gniazdo PCI Express Gen2 x1 x1

Gniazdo PCI x2

Złącze napędu dyskietek x1 Każde złącze obs ługuje 2 napędy dyskietek

Złącze IDE x1 Każde złącze obs ługuje 2 urządzenia IDE

Architektura AMD 64 umożliwia przetwarzanie 32 i 64

bitowe

Obsługa Hyper Transport 3.0 oraz Cool’n’Quiet

Mod uł pamięci DDR2 z trybem podwójnego kanału

Obsługa DDR2 533 / 667 / 800

Obsługa DDR2 1066 (by AM2+ CPU)

Brak obsług i Register ed D IMM oraz ECC DIMM

Interfejs Low Pin Count

Funkcje kontroli warunków pracy,

Mon itor H /W

Funkcja ITE "Smart Gu ard ian"

Maks. wielkość współdz ielon ej pami ęci video wynosi

512 MB

Obsługa DX10 / HDCP / PureV ideo

Ultra DMA 33 / 66 / 100 / 133 Tryb Bus Master

obsługa PIO tryb 0~4,

Transfer danych do 3 Gb/s.

Zgodność ze specyfikacją SATA w wersji 2.0.

10 / 100 / 1000 Mb/s z automatyczną negocjacją

szybkości

Działanie w trybie połowicznego / pełnego dupleksu

5.1 kanałowe wyjście audio

Obsługa H igh- Def in ition A ud io

42

Back Panel

I/O

Wymiary

płyty

Funkcje

specjalne

Obsluga

systemu

operacyjne

go

GF8200 M2+

SPEC

Złącze panela przedniego x1 Obsługa elementów panela przedniego

Przedn ie złącze aud io x1 Obs ługa funkcji audio na panelu przednim

Złącze wejścia CD x1 Obsługa funkcji wejścia audio CD

Złącze wyjścia S/PDIF x1 Obsługa funkcji cyfrowego wyjścia aud io

Złącze główkowe wentylatora procesora

x1

Złącze główkow e went ylatora

systemowego x1

Złącze główkowe kasowan ia CMOS x1

Złącze USB x4

Złącze zasilania (24 pinowe) x1

Złącze zas ilania (4 p ino we) x1

Złącze Port drukarki x1 Każde złącze obs ługuje 1 Port drukarki

Złącze Port szeregowy x1

Klawiatura PS/2 x1

Mys z PS /2 x1

Port VGA x1

Port LAN x1

Port USB x4

Gniazdo audio x3

Port DVI x 1

220 mm (S) X 244 mm (W)

Obsługa RAID 0 / 1 / 5 / 0 +1

Obsługa Hybr id SLI (b y nV IDIA dr iv er )

Windows XP / VISTA

Zasilanie wentylatora procesora (z funkcją Smart Fan)

Zasilanie wentylatora systemowego

Każde złącze obs ługuje 2 porty USB na panelu

przednim

Biostar zastrzega sobie prawo dodawania lub

odwoływ ania obsług i d owo lnego s ys temu

operacyjneg o bez powiado mienia.

43

Motherboard Manual

RUSSIAN

CPU
(централь

ный

процессор

)

FSB

Набо р
микросхем

Основная
память

Super I/O

Графика

IDE

SATA

Локальная
сеть

Звуко ва я

поддержка
жестког о
диска

Слоты

Встроенны
й разъём

44

Гнездо AM2+
Процессоры AMD Athlon 64 / Athlon 64

FX / A lthlon 6 4 X2 / S emp ro n / Phenom

Поддержка HyperTransport 3.0 с
пропускной способностью до 5.2 GT/s

GeForce 8200

Слоты DDR2 DIMM x 4
Максимальная ёмкость памяти 16 ГБ
Каждый модуль DIMM поддерживает

256МБ /512МБ /1 ГБ/2ГБ/4ГБ DDR2

ITE 8718F

Обеспечивает наиболее используемые
действующие фун кцио наль ные
возможно сти Super I/O.

Встроенная в набор микросхем GeForce

8200

Встроенное устройство управлени я
встроенными интерфейсами устройс тв

Встроенное последовательное
устройство управл ения ATA

Realtek RTL 8111C

ALC662

Слот PCI Express Gen2 x16 x1
Слот PCI Express Gen2 x1 x1
Слот PCI x2

Разъ ём НГМД x1

Разъ ём IDE x 1

СПЕЦ

Арх итектура AMD 64 разрешать обработка данных
на 32 и 64 бит
Поддержка Hyper Transport 3.0 и Cool’n’Quiet

Мод уль памяти с двухканальным режимом DDR2
Поддержка DDR2 533 / 667 / 800
Поддержка DDR2 1066 (b y AM2+ CPU)
Не поддерживает зарегистрированные модули

DIMM and ECC DIMM

Интерфейс с ни зким количес твом выводов
Инициативы по охране окружающей среды,
Аппаратный монитор
Функция ITE "Smart Guardian" (Интеллектуальная
защит а)

Максимальная совместно использ уемая вид ео
память составляет 512 МБ
Поддержка DX10 / HDCP / Pur eVideo

Режим "хозяина" шины Ultra D MA 33 / 66 / 100 / 133
Поддержка режима PIO 0~4,

скорость передачи данных до 3 гигабит/с.
Соответствие спецификации SATA версия 2.0.

Автоматическо е согласование 10 / 100 / 1000 Мб/с
Частичная / полна я дуплексная способность

Звуко ва я поддержка H igh- D ef inition

5.1канальный звуковой выход

Каждый разъём поддерживает 2 накопителя на
гибких магнитных дисках
Каждый разъём поддерживает 2 встроенных
интерфейса накопителей

Задняя
панель
средств
ввода-выв
ода

Разм ер
панели

Специальн
ые

техническ
ие

характери
стики

Поддержк
а OS

GF8200 M2+

СПЕЦ

Разъ ём SATA x6 Каждый разъём поддерживает 1 устройс тво SATA
Разъ ём на лицевой панели x1 Поддержка устро йств на лицевой панели
Входной звуковой разъём x1 Поддержка звуко вых функций на лицевой панели

Разъ ём ввода для CD x1 Поддержка функции ввода для CD
Разъ ём вывода для S/PDIF x1 Поддержка выво да цифровой звуковой фун кции
Контактирующее приспособление
вентил ятор а центрального
процессора x1
Контактирующее приспособление
вентил ятор а системы x1
Открытое контактир ующее
приспособление CMOS x1

USB- разъём x4

Разъ ем питания (24 вы вод) x1
Разъ ем питания (4 вывод) x1
Разъ ём Порт подключения
принтера x1
Разъ ём Последоват ельный порт x1

Клавиатура PS/2 x1
Мышь PS/2 x1
Пор т VGA x1
Пор т LAN x1
USB- порт x4
Гнездо для подключени я
наушников x3
Пор т DVI x1

220 мм (Ш) X 244 мм (В)

Поддержка RAID 0 / 1 / 5 / 0+1
Поддержка H ybr id S LI (by nV ID IA d r iver )

Windows XP / VISTA

Источник пит ания для вентилятор а центрального
процессора (с функц ией интеллектуального
вентил ятор а)

Источник пит ания для вентилятор а системы

Каждый разъём поддерживает 2 USB-порта на
лицевой панели

Каждый разъём поддерживает 1 По рт подключения
принтера

Biostar сохраняет за собой право добавлять или
удаля ть средства обеспечения для OS с или без
предварительного уведомле ния .

45

Motherboard Manual

ARABIC

ﺔﻴﻨﻘﺗ ﻦﻜﻤﺗAMD 64 ﺔﻋﺮﺴﺑ ﺔﻴﺑﻮﺳﺎﺤﻟ ا تﺎﻴﻠﻤﻌﻟا ءاﺮﺟإ 32 و64 ﺖﺑ

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗHyper Transp ort و 3.0 Cool’n’Quiet

ﺗﻢﻋﺪ ﺔﻴﻨﻘ ﺗ Low Pin Count Interface

ﺔﺌﻴﺒﻟا ﻲﻓ ﻢﻜﺤﺘﻟا ﻞﺋﺎﺳو:

ةﺰﻬﺟﻷا ﺔﻟﺎﺡ ﺔﻓﺮﻌﻤﻟ ﺐﻗاﺮﻡ

ﺔﻔﻴﻇو"S mart Guard ian" ﻦﻡ ITE

اذ ةﺪﺡو ةﺮآ DDR2 ﻘﻟا ﺔﺟودﺰﻡةﺎﻨ

عﻮﻥ ﻦﻡ ةﺮآاﺬﻟا ﻢﻋﺪﺗDDR2 تﺎﻌﺳ 533 / 667 / 800 ﺖیﺎﺑ ﺎﺠﻴﻡ

عﻮﻥ ﻦﻡ ةﺮآاﺬﻟا ﻢﻋﺪﺗDDR2 تﺎﻌﺳ 1066ﺖیﺎﺑ ﺎﺠﻴﻡ

(DDR2 1066 is by AM2+ CPU)

ةﺮآاﺬﻟا ﻖﺋﺎﻗر ﻢﻋﺪﺗ ﻻDIMM ﻊﻡ ﻖﻓاﻮﺘﺗ ﻻ ﻲﺘﻟا ﻚﻠﺗو ECC

ﻰﺼﻗأ ﺔﻌﺳ ةﺮآاﺬﻟ ﻮیﺪﻴﻔﻟا ﺔآﺮﺘ ﺸﻤﻟا 512 ﺎﺠﻴﻡ ﺖیﺎﺑ

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗDX10 / HDCP / PureVideo

ﺔﻴﻨﻘ ﺘﺑ ﻞﻗﺎﻥUltra DMA 33 / 66 / 100 / 133ﻲﺴﻴﺋر ﻊﺿو

ﻊﺿو ﻢﻋدPIO Mode 0~4

ﻞﻘﻥ تﺎﻥﺎﻴﺒﻟا تﺎﻋﺮﺴﺑ ﻞﺼ ﺗ ﻰﻟإ 3 ﺖﺑﺎﺠﻴﺟ/ﺔﻴﻥﺎﺙ.

ﺔﻘﺑﺎﻄﻡ تﺎﻔﺹاﻮﻤﻟ SATA راﺪﺹﻹا 2.0.

ﻞﻡﺎﻜﻟا جودﺰﻤﻟا ﻞﻘﻨﻟا ﺔﻴﻥﺎﻜﻡإ/ﻲﻔﺼﻨﻟا

5.1 تاﻮﻨﻗ جﺮﺨﻟ تﻮﺼﻟا

ﻦﻡ ﻒیﺮﻌﺘﻟا ﻲﻟﺎﻋ تﻮﺼﻟا ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗ

ﺔﻥﺮﻤﻟا صاﺮﻗﻸﻟ ﻦﻴآ ﺮﺤﻡ ﻢﻋﺪی

ةﺰﻬﺟأ ﻦﻡ ﻦﻴﻨﺙا ﺬﻔﻨﻡ ﻞآ ﻢﻋﺪیIDE

ةﺰﻬﺟأ ﻦﻡ ﺪﺡاو ﺬﻔﻨﻡ ﻞآ ﻢﻋﺪیSATA

ﺔﻴﻡﺎﻡﻷا ﺔﺡﻮﻠﻟا تاﺰﻴﻬﺠﺗ ﻢﻋﺪی

ﻟاتﺎﻔﺻاﻮﻤ

ﺲﺒﻘﻡAM2+

تﺎﺠﻟﺎﻌﻡAMD Athlon 64 / Athlon 64 FX / Sempron /

Phenom / Althlon 64 X2

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗHyperTransport ﺼی ددﺮﺘﺑ ﻰﻟإ ﻞ3.0 5.2 GT/s

GeForce 8200 ﺔﻋﻮﻤﺠﻡ ﺢﺋاﺮﺸﻟا

ITE 8718F

ﺔﻔﻴﻇ و ﺮﻓﻮﺗSuper I/O ًﺎ ﻡ ا ﺪ ﺨ ﺘ ﺳا ﺮﺜآﻷا .

ىﻮﺼﻗ ةﺮآاذ ﺔﻌﺳ16 یﺎﺑ ﺎﺠﻴﺟﺖ

ﺔﺤﺘﻓ ﻞآ ﻢﻋﺪﺗDIMM عﻮﻥ ﻦﻡ ةﺮآاذ ﻢﻋﺪﺗ DDR2 ﺔﻌﺳ

ﻖﺋﺎﻗر ﻲﻓ ﺔﺠﻡﺪﻡ GeForce 82 00

ﻲﺋﺎﻘﻠﺗ ضو ﺎﻔﺗ10/100/1000 ﺖیﺎﺑ ﺎﺠﻴﻡ /ﺔﻴﻥﺎﺙ

256/512 ﺎﺠﻴﻡ

ﻢﻜﺤﺘﻡIDE ﻞﻡﺎﻜﺘﻡ ﺬﻔﻨﻡ ID E

ﻢﻜﺤﺘﻡ Serial ATA ﻞﻡﺎﻜﺘﻡ

Realtek RTL 8111C

ﺔﺤﺘﻓx16 PCI Express Gen2 دﺪﻋ1

ﺔﺤﺘﻓx1 PCI Express Gen2 دﺪﻋ1

ﺔﺤﺘﻓPCI دﺪﻋ2

ﻗأ كﺮﺤﻡ ﺬﻔﻨﻡﺔﻥﺮﻡ صاﺮ دﺪﻋ1

ﺔﻴﻡﺎﻡﻷا ﺔﺡﻮ ﻠﻟا ﺬﻔﻨﻡ دﺪﻋ1

ﺔﺤﺘﻓDDR2 DIM M دﺪﻋ4

و ﺖیﺎﺑ1/و 2/و 4 ﺎﺠﻴﺟﺖیﺎﺑ

ALC662

ﺬﻔﻨﻡIDE دﺪﻋ1

ﺬﻔﻨﻡSATA دﺪﻋ6

ةﺪﺡو ﺔﺠﻟﺎﻌﻤﻟا

ﺔیﺰآﺮﻤﻟا

ﻞﻗﺎﻨﻟا ﻲﻡﺎﻡﻷا ﻲﺒﻥﺎﺠﻟا

Super I/O

ةﺮآاﺬﻟا ﺔﻴﺴﻴﺋﺮﻟا

ﺔﻗﺎﻄﺑ تﺎﻡﻮﺳﺮﻟا

SATA

ﺔﻜﺒﺵ ﺔﻴﻠﺥاد

ﻢﻋد تﻮﺼﻟا ﻲﻟ ﺎﻋ

ﻒیﺮﻌﺘﻟا

تﺎﺤﺘﻔﻟا

ﺬﻓﺎﻨﻤﻟا ﻰﻠﻋ ﺢﻄ ﺳ

ﺔﺡﻮﻠﻟا

46

ﺔﻴﻡﺎﻡﻷا ﺔﺡﻮﻠﻟ ﺎﺑ تﻮﺼﻟا ﺔﻔﻴﻇو ﻢﻋﺪی

ﺞﻡﺪﻤﻟا صﺮﻘﻟا تﻮﺹ ﻞﺥد ﺔﻔﻴﻇو ﻢﻋﺪی

ﻲﻤﻗﺮﻟا تﻮﺼﻟا جﺮﺥ ﺔﻔﻴﻇو ﻢﻋﺪی

ﺔﻔﻴﻇو ﻊﻡ ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺡو ﺔﺡوﺮﻤﻟ ﺔﻗﺎﻄ ﻟا ﻞﻴﺹﻮﺘﻟSmart Fan

مﺎﻈﻨﻟا ﺔﺡوﺮﻤﻟ ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺘﻟ

ﻲﺘﺤﺘﻓ ﺬﻔﻨﻡ ﻞآ ﻢﻋﺪیUSBﺔﻴﻡﺎﻡﻷا ﺔﺡﻮﻠﻟﺎﺑ

ﻆﻔﺘﺤﺗBiostar ﺔﻓﺎﺿإ ﻲﻓ ﺎﻬﻘﺤﺑ وأ رﺎﻄﺥﺈﺑ ﻞﻴﻐﺸﺗ مﺎﻈﻥ يﻷ ﻢﻋﺪﻟا ﺔﻟازإ وأ

GF8200 M2+

ﻟاتﺎﻔﺻاﻮﻤ

ﻲﻡﺎﻡﻷا تﻮﺼﻟا ﺬﻔﻨﻡ دﺪﻋ1

ﺬﻔﻨﻡCD-IN دﺪﻋ1

جﺮﺥ ﺬﻔﻨﻡS/PDIF دﺪﻋ1

ﺔیﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺡو ﺔﺡوﺮﻡ ﺔﻠﺹو دﺪﻋ1

مﺎﻈﻨﻟا ﺔﺡوﺮﻡ ﺔﻠﺹو دﺪﻋ1

ﺢﺴ ﻡ ﺔﻠﺹوCMOS دﺪﻋ1

ﺬﻔﻨﻡUSB دﺪﻋ4

ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ)24سﻮﺑد( دﺪﻋ1

ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ)4سﻮﺑد( دﺪﻋ1

ﺔﻌﺑﺎﻃ ﺬﻔﻨﻡ دﺪﻋ1

ﻲﻠﺴﻠﺴﺗ ﺬﻔ ﻨﻡ دﺪﻋ1

ﺢﻴﺗﺎﻔﻡ ﺔﺡﻮﻟPS/2 دﺪﻋ1

سوﺎﻡ PS/2 دﺪﻋ1

ﺬﻔﻨﻡVG A دﺪﻋ1

220 ﻢﻡ)ضﺮﻋ (X 244 ﻢﻡ)عﺎﻔﺗرا( ﻢﺠﺡ ﺔﺡﻮﻠﻟا

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗRAID 0 / 1 / 5 / 0 +1

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗHybrid S L I (by n V ID IA dr iver )

Windows XP / VISTA

رﺎﻄﺥإ نوﺪﺑ.

ﺒﺵ ﺬﻔﻨﻡﺔﻴﻠﺤﻡ لﺎﺼﺗا ﺔﻜ دﺪ ﻋ1

ﺬﻓﺎﻨﻡUS B دﺪﻋ4

تﻮﺹ ﺲﺒﻘﻡ ﺪﻋ3

ﺬﻓﺎﻨﻡDVI دﺪﻋ1

ﺬﻓﺎﻨﻡ ﻞﺥد/جﺮﺥ

ﺔﺡﻮﻠﻟا ﺔﻴﻔﻠﺨﻟا

ﺔﺹﺎﺥ ﺎیاﺰﻡ

ﻢﻋد ﺔﻤﻈﻥأ ﻞﻴﻐﺸﺘﻟا

47

Motherboard Manual

JAPANESE

Socket AM2+

CPU

FSB

チップセッ

ト

メインメモ

リ

Super I/O

グラフィッ

クス

IDE 統合 IDE コントローラ

SATA 統合シ リアルATA コントローラ

LAN Realtek RTL 8111C

HDオ ーディ

オのサポート ALC662

AMD Athlon 64 / Athlon 64 FX / A lthlon 64

X2 / S empron / Phenom プロ セッ サ

5.2 GT/sのバンド 幅まで ハイパート ランスポ

ート3.0をサポ ートします

GeForce 8200

DDR2 DIMMスロット x 4

最大メモリ容 量16GB

各DIMMは 256MB/512 MB /1GB/2GB/4GB

DDR2をサポート

ITE 8718F

もっとも一般 に使 用されるレ ガシーSuper I/O

機能を採用し てい ます。

GeForce 8200チップ セットに統 合

仕様

AMD 64アーキ テクチャで は、32ビットと64 ビッ ト計算が可

能です

ハイパートラ ンス ポート3.0と クールアン ドクワイア ット を

サポートしま す

デュアル チ ャン ネルモードDDR2メモリモジ ュール

DDR2 533 / 667 / 800 をサポート

DDR2 1066 をサポート (by A M2+ CPU)

登録済みDIMMとECC DIMMはサポ ートされま せん

低ピンカウン トイ ンターフェ イス

環境コントロ ール イニシアチ ブ、

H/Wモニター

ITE の「スマート ガー ディアン」 機能

最大の共有ビ デオ メモリは512MBです

DX10 / HDC P / PureVideo のサポー ト

Ultra DMA 33 / 66 / 100 / 133バスマ スタ モード

PIO Mode 0~4のサポート 、

最高3Gb/秒の データ転送 速度

SATAバージョン2.0仕様に準拠。

10 / 100 / 1000 Mb/秒のオート ネゴシ エーション

半/全二重機能

5.1チャンネル オーディオ アウ ト

ハイデフィニ ショ ンオーディ オのサポー ト

スロット

オンボード

コネクタ

48

PCI Express Gen2 x16スロット x1

PCI Express Gen2 x1スロ ット x1

PCIスロット x2

フロッピーコ ネク タ x1 各コネクタは2つのフロ ッピー ドライブを サポ ートします

IDE コネクタ x1 各コネクタは 2つのIDE デバイスをサポ ートし ます

SATAコネクタ x6 各コネクタは 1つのSATAデバイスをサポ ート します

フロントパネ ルコ ネクタ x1 フロン トパネル機 能をサ ポートしま す

フロントオー ディ オコネクタ x1 フロン トパネ ルオーディ オ機能をサ ポー トします

CDインコネクタ x1 CDオーデ ィオイン機 能をサポー トしま す

S/PDIFアウトコネ クタ x1 デジタルオー ディ オアウト機 能をサポー トしま す

CPUファンヘッダ x1 CPUファン電源装置(スマートファン 機能を搭載 )

システムファ ンヘ ッダ x1 システムファ ン電 源装置

CMOSクリアヘッダ x1

USBコネク タ x4

電源コネクタ (24 ピン) x1

電源コネクタ (4ピン) x1

プリンタポー トコ ネクタ x1 各コネ クタは1つのプリ ンタポ ートをサポ ート します

シリアルポー トコ ネクタ x1

PS/2キーボード x1

PS/2マウス x1

背面パネル

I/O

ボードサイ

ズ

特殊機能

OSサポー ト W indows XP / VISTA

VGAポート x1

LANポート x1

USBポート x4

オーディオジ ャッ ク x3

DVIポート x1

220 mm (幅) X 244 mm (高さ)

RAID 0 / 1 / 5 / 0+1 の サポー ト

Hybr id SL I のサ ポー ト(b y nV IDIA d r iv er)

GF8200 M2+

仕様

各コネクタは 2つのフロ ントパネル USBポートをサ ポート し

ます

Biostarは事前の サポートな しにOSサ ポー トを追加ま たは削

除する権利を 留保 します。

2008/04/11

49