Biostar GF8200E Owner's Manual

GF8200E Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the contents here and specially disclaims any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves the right to revise this publication and to make changes to the contents here without obligation to notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and we will not be responsible for any mistakes found in this user’s manual. All the brand and product names are trademarks of their respective companies.

Table of Contents

Chapter 1: Introduction ............................................................ 1

1.1 Before You Start ................................................................................ 1

1.2 Package Checklist............................................................................. 1

1.3 Motherboard Features...................................................................... 2

1.4 Rear Panel Connectors ..................................................................... 3

1.5 Motherboard Layout......................................................................... 4

Chapter 2: Hardware Installation ............................................. 5

2.1 Installing Central Processing Unit (CPU)....................................... 5

2.2 FAN Headers...................................................................................... 7

2.3 Installing System Memory ................................................................ 8

2.4 Connectors and Slots....................................................................... 10

Chapter 3: Headers & Jumpers Setup ..................................... 14

3.1 How to Setup Jumpers .................................................................... 14

3.2 Detail Settings.................................................................................. 14

Chapter 4: RAID Functions ..................................................... 19

4.1 Operating System............................................................................ 19

4.2 Raid Arrays...................................................................................... 19

4.3 How RAID Works............................................................................. 19

Chapter 5: Useful Help ............................................................ 23

5.1 Driver Installation Note.................................................................. 23

5.2 Software ............................................................................................ 24

5.3 Extra Information............................................................................ 29

5.4 AMI BIOS Beep Code....................................................................... 31

5.5 Troubleshooting............................................................................... 32

Appendix: SPEC In Other Languages ...................................... 34

German.................................................................................................................. 34

French .................................................................................................................... 36

Italian..................................................................................................................... 38

Spanish ................................................................................................................... 40

Portuguese ............................................................................................................ 42

Polish...................................................................................................................... 44

Russian ................................................................................................................... 46

Arabic..................................................................................................................... 48

Japanese ................................................................................................................ 50

CHAPTER 1: INTRODUCTION

GF8200E

1.1 B

EFORE YOU START

Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with

sufficient lighting.

 Always disconnect the computer from power outlet

before operation.

 Before you take the motherboard out from anti-static

bag, ground yourself properly by touching any safely grounded appliance, or use grounded wrist strap to remove the static charge.

 Avoid touching the components on motherboard or the

rear side of the board unless necessary. Hold the board on the edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the

case after installation. Loose parts will cause short circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

 The operating temperatures of the computer should be

0 to 45 degrees Celsius.

1.2 PACKAGE CHECKLIST

IDE Cable X 1 Serial ATA Cable X 1 Rear I/O Panel for ATX Case X 1 Installation Guide X 1 Fully Setup Driver CD X 1 (full version manual files inside) FDD Cable X 1 (optional) USB 2.0 Cable X1 (optional) Serial ATA Power Cable X 1 (optional)

Note: The package contents may be different due to area or your motherboard version.

Motherboard Manual

1.3 MOTHERBOARD FEATURES

SPEC

Socket AM2+

CPU

FSB

Chipset GeForce 8200

Super I/O

Main

Memory

Graphics Integrated in GeForce 8200 Chipset

IDE Int egrated IDE C on troller

SATA II Integrated Serial ATA Controller

LAN Realtek RTL 8111DL

Sound ALC662

Slots

On Board

Connector

AMD Sempron / Athlon / Athlon II / Phenom

/ Phenom II processors

(Max imum Watt: 95W)

Support HyperTransport 3.0

Supports up to 5.2 GT/s Bandwidth

ITE 8718

Prov ides the most commonly used legacy

Super I/O functionality

DDR2 DIMM Slots x 2

Max Memory Capacity 8GB

Each DIMM supports 256MB/512MB/

1GB/2GB/4GB DDR2

PCI Express Gen2 x16 slot x1 Supports PCI-E Gen2 x16 expansion cards

PCI slot x2 Supports PCI expansion cards

Floppy Connector x1 Each connector supports 2 Floppy drives

IDE Connector x1 Each co nnect or supports 2 IDE device

SATA Connector x4 Each co nnector supports 1 SATA devices

Front Panel Connector x1 Supports front panel facilit ies

AMD 64 Architecture enables 32 and 64 bit

computing

Supports Hyper Transport 3.0 and Cool=n=Quiet

Low Pin Count Interface

En vironment Cont ro l in it iat ives

H/W Monitor

ITE's "Smart Guard ian" funct ion

Dual Channe l Mode DD R2 me mory modu le

Supports DDR2 533 / 667 / 800

Supports DDR2 1066 (by AM2+/AM3 CPU)

Registered DIMM and ECC DIMM is not s uppo rted

Max Shared V ideo Memo ry is 5 12 MB

DX10 / HDCP / PureVid eo support

Ultra DMA 33 / 66 / 100 / 133 Bus Master Mod e

supports PIO Mode 0~4,

Data transfer rates up to 3 Gb/s

SATA Ver sio n 2.0 s pe cif icat ion co mpliant

10 / 100 / 1000 Mb/s auto n egotiation

Half / Full duplex capability

5.1 channels audio out

High Definition Audio

SPEC

Front Audio Connector x1 Supports front panel audio function

S/PDIF Out Connector x1 Supports digital audio out function

CPU Fan Header x1 CPU Fan power supply (with Smart Fan funct ion)

System Fan Header x1 System Fan Power supply

CMOS C lear Header x1 Restore CMOS data to factory def ault

USB Connector x2 Each connector support s 2 front panel US B ports

Power Connector (24pin) x1 Connects to Power supp ly

Power Connector (4pin) x1 Connects to Power supply

Printer Port Connector x1 Each connector supports 1 Printer port

Serial Port Connector x1 Connects to RS-232 Port

PS/2 Keyboard x1

PS/2 Mouse x1

Back Panel

I/O

Board Size 190 mm(W) x 245 mm(L) uATX

Special

Features

OS Support Windows XP / Vista 32 / 64

DVI Port x1

VGA Port x1

LAN Port x1

USB Port x4

Audio Jack x3

RAID 0 / 1 / 5 / 0+1 support

Hyb rid SL I support (by nVID IA d river)

Connects to PS/2 Keyboard

Connects to PS/2 Mouse

Connect to DVI-D monitor

Connect to D-SUB monitor

Connect to RJ-45 ethernet cable

Connect to USB dev ices

Provide Audio-In/Out and microphone connection

Biostar reserves the right to add or remove support

for any OS With or without notice.

1.4 R

EAR PANEL CONNECTORS

GF8200E

PS/2 Mou se

PS/2 Keyboard

VGA

DVI-D

LAN

Line In/ Surr ound

Line Out

Mic In 1/ Bass/ Center

USB X2USBX2

Motherboard Manual

1.5 MOTHERBOARD LAYOUT

KBMS1

AT X PWR 2

VGA1

DVI1

USB1

RJ45USB1

AUDIO1

LAN

JUSBV1

CPU_FAN1

GeForce

PEX16_1

8200

Socket AM2+

F_USB2

F_USB1

ATXPWR1

DIMM A1

DIM MB1

IDE1

JUSBV2

BAT1

F_AUDIO1

Codec

Note: represents the 1■

JSPDIFOUT1

PCI1

JCMO S1

SATA1

BIO S

SATA3

Super

I/O

PCI2

F_PRINT1F_COM1

pin.

FDD

SATA2

SYS_FAN1

PAN EL 1

SATA4

CHAPTER 2: HARDWARE INSTALLATION

GF8200E

2.1 I

NSTALLING CENTRAL PROCESSING UNIT (CPU)

Step 1: Pull the lever toward direction A from the socket and then raise the

lever up to a 90-degree angle.

Step 2: Look for the white triangle on socket, and the gold triangle on

CPU should point towards this white triangle. The CPU will fit only in the correct orientation.

Motherboard Manual

Step 3: Hold the CPU down firmly, and then close the lever toward direct

B to complete the installation.

Step 4: Put the CPU Fan on the CPU and buckle it. Connect the CPU

FAN power cable to the CPU_FAN1. This completes the installation.

Note: Please update the BIOS to the latest version while using AM2+/AM3 CPUs. Due to the latest

CPU transition, you may encounter the situation that the new system failed to boot while using new AM2+/AM3 CPUs. In this case, please install one standard AM2 CPU to boot your system, and update the latest BIOS from our website for AM2+/AM3 CPUs support.

GF8200E

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufact urer. Connect the fan cable to the connector while matching the black wire to pin#1.

CPU_FAN1: CPU Fan Header

Assignment

1 Ground

SYS_FAN1: System Fan Header

2 +12V 3

FAN RPM r ate sense

4 Smart Fan

Control (By Fan)

Assignment

1 Ground 2 +12V 3 FAN RPM rate

sense

Note:

CPU_FAN1 supports 4-pin head connector. SYS_FAN1 supports 3-pin head connector. When connecting with wires onto connectors, please note that the red wire is the positive and should be co nnected to pin#2, and the black wire is Ground and should be connected to GND.

Motherboard Manual

2.3 INSTALLING SYSTEM MEMORY

A. Memory Modules

DIMMA1

DIMMB1

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot such that the notch on the DIMM matches the break on the Slot.

2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated.

GF8200E

B. Memory Capacity

DIMM Socket

Location

DIMMA1 256MB/512MB/1GB/2GB/4GB

DIMMB1 256MB/512MB/1GB/2GB/4GB

DDR2 Module

Total Memory

Size

Max is 8GB.

C. Dual Channel Memory installation

Please refer to the following requirements to activate Dual Channel function:

Install memory module of the same density in pairs, shown in the table.

Dual Channel Status DIMMA1 DIMMB1

Disabled O X

Disabled X O

Enabled O O

(O means memory installed, X means memory not installed.)

The DRAM bus width of the memory module must be the same (x8 or x16)

Motherboard Manual

2.4 CONNECTORS AND SLOTS

FDD: Floppy Disk Connector

The motherboard provides a standard floppy disk connector that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the provided floppy drive ribbon cable.

234

IDE1: IDE/ATAPI Connector

The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.

The IDE connector can connect a master and a slave drive, so you can connect up to two drives.

133

3940

GF8200E

SATA1~SATA4: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 4 channels SATA interface, it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.

Assignment

1 Ground

SATA1 SAT A3

SATA2 SATA4

2 TX+ 3 TX4 Ground 5 RX6 RX+ 7 Ground

ATXP WR1: AT X Power Source Connector

This connector allows user to connect 24-pin power connector on the ATX power supply.

Pin Assignment Pin Assignment

13 +3.3V 1 +3.3V 14 -12V 2 +3.3V 15 Ground 3 Ground 16 PS_ON 4 +5V 17 Ground 5 Ground 18 Ground 6 +5V 19 Ground 7 Ground 20 NC 8 PW_OK 21 +5V 9 Standby Voltage+5V 22 +5V 10 +12V 23 +5V 11 +12V 24 Ground 12 +3.3V

Motherboard Manual

ATXP WR2: AT X Power Source Connector

Connecting this connector will provide +12V to CPU power circuit.

Note:

Before power on the system, please make sure that both ATXPWR1 and ATXPWR2 connectors ha ve been plugged-in.

PEX16_1: PCI-Express Gen2 x16 Slot

- PCI-Express 2.0 compliant.

- Maximum theoretical realized bandwidth of 8GB/s simultaneously per

direction, for an aggregate of 16GB/s totally.

- PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.

- 2X bandwidth over the PCI-Express 1.0 architecture.

1 +12V 2 +12V 3 Ground 4 Ground

Assignment

PEX16_1

PCI1/PCI2: Peripheral Component Interconnect Slots

This motherboard is equipped with 2 standard PCI slots. PCI stands for Peripheral Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as 32 bits.

PCI1

GF8200E

PCI2

Motherboard Manual

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 H

OW TO SETUP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is “open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SETTINGS

PANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and speaker connection. It allows user to connect the PC case’s front panel switch functions.

PWR_LED

On/Off

SPK

HLED

RST

9 1

Pin Assignment Function Pin Assignment Function

1 +5V 9 N/A 2 N/A 10 N/A 3 N/ A 1 1 N/A N/ A 4 Speaker 5 HDD LED (+) 13 Power LED (+) 6 HDD LED (-) 7 Ground 15 Power button 8 Reset control

Speaker Connector

Hard drive LED

Reset button

12 Power LED (+)

14 Power LED (-)

16 Ground

N/A

Power LED

Power-on button

+ 37 hidden pages

Biostar GF8200E Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual