Biostar A75MG Owner's Manual

A75MG Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment ge nerates, uses, and can radiate radio frequency
energy and, if not i nstalled and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.

Dichiar azione di conformit à
sintetica

Ai sensi dell’art. 2 comma 3 del D.M.
275 del 30/10/2002

Si dichiara che questo prodotto è
conforme alle normative vigenti e
soddisfa i requisiti essenziali richiesti
dalle direttive

2004/108/CE, 2006/95/CE e
1999/05/CE

quando ad esso applicabili

Short De cla ration of conf ormity

We declare this product is complying
with the laws in force and meeting all
the essential requirements as specified
by the directives

2004/108/CE, 2006/95/CE and
1999/05/CE

whenever these laws may be applied

Table of Contents

Chapter 1: Introduction ........................................ 1

1.1 Before You Start ................................................................................ 1

1.2 Package Checklist............................................................................. 1

1.3 Motherboard Features...................................................................... 2

1.4 Rear Panel Connectors ..................................................................... 3

1.5 Motherboard Layout......................................................................... 4

Chapter 2: Hardware Installation .......................... 5

2.1 Installing Central Processing Unit (CPU) ....................................... 5

2.2 FAN Headers...................................................................................... 7

2.3 Installing System Memory ................................................................ 8

2.4 Connectors and Slots....................................................................... 10

Chapter 3: Headers & Jumpers Setup ................... 13

3.1 How to Setup Jumpers .................................................................... 13

3.2 Detail Settings.................................................................................. 13

Chapter 4: AMD DUAL Graphics Technology ......... 18

4.1 AMD Dual Graphics Technology Introduction............................. 18

4.2 AMD Dual Graphics Requirement ................................................ 18

4.3 AMD Dual Graphics Setup.............................................................. 19

Chapter 5: RAID Functions .................................. 20

5.1 Operating System............................................................................ 20

5.2 Raid Arrays ...................................................................................... 20

5.3 How RAID Works............................................................................. 20

Chapter 6: Useful Help ........................................ 23

6.1 Driver Installation Note.................................................................. 23

6.2 Software ............................................................................................ 24

6.3 Extra Information............................................................................ 28

6.4 AMI BIOS Beep Code....................................................................... 30

6.5 Troubleshooting............................................................................... 31

Appendix: SPEC In Other Languages ................... 32

German.................................................................................................................. 32

French .................................................................................................................... 34

Italian..................................................................................................................... 36

Spanish ................................................................................................................... 38

Portugue se ............................................................................................................ 40

Polish...................................................................................................................... 42

Russian ................................................................................................................... 44

Arabic..................................................................................................................... 46

Japanese ................................................................................................................ 48

CHAPTER 1: INTRODUCTION

A75MG

1.1 B

EFORE YOU START

Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:

 Prepare a dry and stable working environment with

sufficient lighting.

 Always disconnect the computer from power outlet

before operation.

 Before you take the motherboard out from anti-static

bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.

 Avoid touching the components on motherboard or the

rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.

 Do not leave any unfastened small parts inside the

case after installation. Loose parts will cause short
circuits which may damage the equipment.

 Keep the computer from dangerous area, such as heat

source, humid air and water.

 The operating temperatures of the computer should be

0 to 45 degrees Celsius.

1.2 PACKAGE CHECKLIST

Serial ATA Cable x2
Rear I/O Panel for ATX Case x1
Installation Guide x1
Fully Setup Driver DVD x1

Note: The package contents may be different due to area or your motherboard version.

1

Motherboard Manual

1.3 MOTHERBOARD FEATURES

SPEC

Socket FM1

CPU

Chipset AMD A75

Super I/O

Main

Memory

SATA III Integrated Serial ATA Controller

LAN RTL8111F

AMD A-Series / E2-Series / Athlon II /

Sempron processors

ITE 8728

Prov ides the most commonly us ed legacy

Super I/O functionality

Low Pin Count Interface

DDR3 DIMM Slots x 2

Max Memory Capacity 16GB

Each DIMM supports 512MB/

1GB/2GB/4GB/8GB DDR3

AMD 64 Architecture enables 32 and 64 bit

computing

(Maximum Watt: 100W)

En v ironm en t Cont rol init iatives

H/W Mon ito r

Fan Sp eed Controller

ITE's "S mart Guard ian" function

Dual Channel Mode DDR3 me mory mo du le

Supports DDR3 800/1066/1333/1600/1866

Register ed DIMM and ECC D IMM is not supported

Data transfer rates up to 6 Gb/s.

SATA Version 3.0 s p e c if icat ion co mpliant .

RAID 0,1,10 support

10 / 100 / 1000 Mb/s auto negotiation

Half / Full duplex capability

Sound ALC662

USB3.0

Slots

On Board

Connectors

A75 Data transfer rates up to 600 MB/s

PCI Express Gen2 x16 Slot x1

PCI Slot x1

SATA Connector x4 Each connector support s 1 SATA device

Front Panel Connector x1 Supports front panel facilities

Front Audio Connector x1 Supports front panel audio function

CPU Fan Header x1 CPU Fan power supply (with Smart Fan function)

System Fan Header x1 System Fan Power supply

CMOS clear Header x1 Restore CMOS data to factory default

2

5.1channels audio out

Supports HD Audio

Supports PCI-E Gen2 x16 expansion card

Supports PCI expansion card

A75MG

SPEC

USB2.0 Connector x2 Each connector supports 2 front panel USB2.0 ports

USB3.0 Connector x1 Each connector supports 2 front panel USB3.0 ports

Printer Port Connector x1 Each connector supports 1 Printer port

Serial Port Connector x1 Connects to RS-232 Port

Power Connector (24-Pin) x1 Connects to Power supply

Power Connector (4-Pin) x1 Connects to Power supply

PS/2 Keybo ard / Mous e x1

VGA Port x1

Rear Panel

I/O

Board Size

OS Support

DVI-D Port x1

LAN port x1

USB2.0 Port x2

USB3.0 Port x2

Audio Jack x3

192 mm (W) x 235.48 mm (L) uATX

Windows XP / Vista / 7

1.4 REAR PANEL CONNECTORS

Connects to PS/2 Keyboard / Mouse

Connect to D-SUB monitor

Connect to DVI monitor

Connect to RJ- 45 ethe rnet cab le

Connect to USB2.0 devices

Connect to USB3.0 devices

Provide Audio-In/Out and Mic. connection

Biostar reserves the r ight to add or remove support

for any OS With or without notice.

NOTE: DVI-D / VGA Output require an AMD family processor with intedrated graphics.
NOTE: Since the audio chip supports High Definition Audio Specification, the function of each

audio jack can be defi ned by software. The input / output function of each audio jack listed
above represents the default setting. However, when connecting external microphone to

NOTE: Maximum resolution:

the audio port, please use the Line In (Blue) and Mic In (Pink) audio jack.

DVI: 1920 x 1200 @60Hz
VGA: 2048 x 1536 @75Hz

3

Motherboard Manual

1.5 MOTHERBOARD LAYOUT

4

Note: represents the 1■

st

pin.

CHAPTER 2: HARDWARE INSTALLATION

A75MG

2.1 I

NSTALLING CENTRAL PROCESSING UNIT (CPU)

Step 1: Pull the lever toward direction A from the socket and then raise the

lever up to a 90-degree angle.

Step 2: Look for the white triangle on socket, and the gold triangle on

CPU should point towards this white triangle. The CPU will fit only
in the correct orientation.

5

Motherboard Manual

Step 3: Hold the CPU down firmly, and then close the lever toward direct

B to complete the installation.

Step 4: Put the CPU Fan on the CPU and buckle it. Connect the CPU

FAN power cable to the CPU_FAN1. This completes the
installation.

6

2.2 FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.

CPU_FAN1: CPU Fan Header

Pin

Assignment

1 Ground
2 +12V
3

FAN RPM rate sense

4 Smart Fan Control (By

Fan)

SYS_FAN1: System Fan Header

Pin Assignment

1 Ground
2 +12V
3

FAN RPM rate sense

A75MG

Note:

CPU_FAN1, SYS_FAN1 support 4-pin and 3-pin head connectors. When connecting
with wires onto connectors, please note that the red wire is the positive and should be
connected to pin#2, and the black wire is Ground and should be connected to GND.

7

Motherboard Manual

2.3 INSTALLING SYSTEM MEMORY

A. DDR3 Modules

Step1:

Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the
slot such that the notch on the DIMM matches the break on the Slot.

Step2:

Insert the DIMM vertically and firmly into the slot until the retaining chip snap
back in place and the DIMM is properly seated.

Note:

If the DIMM does not go in smoothly, do not force it. Pull it all the way out and
try again.

8

B. Memory Capacity

A75MG

DIMM Socket

Location

DDR3_A1 512MB/1GB/2GB/4GB/8GB

DDR3_B1 512MB/1GB/2GB/4GB/8GB

DDR3 Module

Total Memory Size

Max is 16GB.

C. Dual Channel Memory Installation

Please refer to the following requirements to activate Dual Channel function:
Install memory module of the same density in pairs, shown in the table.

Dual Channel Status DDR3_A1 DDR3_B1

Disabled O X

Disabled X O

Enabled O O

(O means memory installed, X means memory not installed.)

Note:

The DRAM bus width of the memory module must be the same (x8 or x16)

D. DDR Speed Support

Please refer to the following table for DDR speed reference:

# of DIMM per Channel # of Ranks per DIMM

1 of 1 UDIMM xR DDR3-1866

1 of 2 UDIMMs xR DDR3-1600 / DDR3-1333

Max DDR Speed Grade

for 1.50V DIMM

Note:

xR: Single or double side memory moudule

9

Motherboard Manual

2.4 CONNECTORS AND SLOTS

ATXP W R2: AT X P ower Source Connector

This connector will provide +12V to CPU power circuit.

ATXP W R1: AT X P ower Source Connector

This connector allows user to connect 24-pin power connector on the ATX
power supply.

Pin

Assignment

1 +12V
2 +12V
3 Ground
4 Ground

Pin Assignment Pin Assignm ent

13 +3.3V 1 +3.3V
14 -12V 2 +3.3V
15 Ground 3 Ground
16 PS_ON 4 +5V
17 Ground 5 Ground
18 Ground 6 +5V
19 Ground 7 Ground
20 NC 8 PW_OK
21 +5V 9 Standby Voltage+5V
22 +5V 10 +12V
23 +5V 11 +12V
24 Ground 12 +3.3V

Note: Before you power on the system, please make sure that both ATXPWR1 and
ATXPWR2 connec tors have been plugged-in.

10

A75MG

PCI1: Peripheral Component Interconnect Slot

This motherbo ard is e quipped with 1 standard P CI slot . PCI stands for P eriphera l
Component Interconne ct, and it is a bus standard for expansio n cards.

PEX16_1: PCI-Express Gen2 x16 Slot

- PCI-Express 2.0 compliant.

- Maximum theoretical realized bandwidth of 8GB/s simultaneously per

direction, for an aggregate of 16GB/s totally.

- PCI-Express Gen2 supports a raw bit-rate of 5.0Gb/s on the data pins.

- 2X bandwidth over the PCI-Express 1.1 architecture.

11

Motherboard Manual

SATA1~SATA4: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 4 channels SATA interface,
it satisfies the SATA 3.0 spec and with transfer rate of 6.0Gb/s.

Pin

Assignment

1 Ground
2 TX+
3 TX­4 Ground
5 RX­6 RX+
7 Ground

12

CHAPTER 3: HEADERS & JUMPERS SETUP

A75MG

3.1 H

OW TO SETUP JUMPERS

The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.

Pin opened Pin closed Pin1-2 closed

3.2 DETAIL SETTINGS

PANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.

Pin Assignment Function Pin Assignment Function

1 +5V 9 N/A
2 N/A 10 N/A
3 N/ A 1 1 N/ A N/ A
4 Speaker
5 HDD LED (+) 13 Power LED (+)
6 HDD LED (-)
7 Ground 15 Power button
8 Reset control

Speaker
Connector

Hard drive
LED

Reset button

12 Power LED (+)

14 Power LED (-)

16 Ground

N/A

Power LED

Power-on button

13

Motherboard Manual

JFRONT_USB3_1: Header for USB 3.0 Ports at Front Panel

This header allows user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.

Pin Assignment Pin Assignment

1 VBUS0 11 D2+
2 SSRX1- 12 D2­3 SSRX1+ 13 Ground

4 Ground 14 SSTX2+
5 SSTX1- 15 SSTX2-

6 SSTX1+ 16 Ground
7 Ground 17 SSRX2+
8 D1- 18 SSRX2-

9 D1+ 19 VBUS1

10 ID 20 Key

F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel

This header allows user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.

14

Assignment

Pin

1 +5V (fused)
2 +5V (fused)
3 USB­4 USB­5 USB+
6 USB+
7 Ground
8 Ground
9 NC

10 Key

A75MG

F_AUDIO1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front
panel. This header supports HD and AC’97 audio front panel connector.

Pin Assignment Pin Assignment

1 Mic Left in 1 Mic In
2 Ground 2 Ground
3 Mic Right in 3 Mic Power
4 GPIO 4 Audio Power
5 Right line in 5 RT Line Out
6 Jack Sense 6 RT Line Out
7 Front Sense 7 Reserved
8 Key 8 Key
9 Left line in 9 LFT Line Out

10 Jack Sense 10

Note: It is recommended that you connect a high-definition front panel audio module to
this connector to avail of the motherboard's high definition audio capability.

HD Audio AC’97

LFT Line Out

15

Motherboard Manual

JCMOS1: Clear CMOS Header

Placing the jumper on pin2-3, it allows user to restore the BIOS safe setting and
the CMOS data. Please carefully follow the procedures to avoid damaging the
motherboard.

※ Clear CMOS Procedures:

1. Remove AC power line.

2. Set the jumper to “Pin 2-3 close”.

3. Wait for five seconds.

4. Set the jumper to “Pin 1-2 close”.

5. Power on the AC.

6. Load Optimal Defaults and save settings in CMOS.

31

Pin 1-2 Close:

Normal Operation (default).

Pin 2-3 Close:

Clear CMOS data.

31

J_COM1: Serial Port Connector

The motherboard has a Serial Port Connector for connecting RS-232 Port.

16

Assignment

Pin

1 Carrier detect
2 Received data
3 Transmitted data
4 Data terminal
5 Signal ground
6 Data set ready
7 Request to send
8 Clear to send
9 Ring indicator

10 NC

J_PRINT1: Printer Port Connector

This header allows you to connector printer on the PC.

Pin Assignment Pin Assignment

1 -Strobe 14 Ground
2 -ALF 15 Data 6
3 Data 0 16 Ground
4 -Error 17 Data 7
5 Data 1 18 Ground
6 -Init 19 -ACK
7 Data 2 20 Ground
8 -Scltin 21 Busy

9 Data 3 22 Ground
10 Ground 23 PE
11 Data 4 24 Ground
12 Ground 25 SCLT
13 Data 5 26 Key

A75MG

17

Motherboard Manual

CHAPTER 4: AMD DUAL GRAPHICS TECHNOLOGY

4.1 AMD

DUAL GRAPHICS TECHNOLOGY INTRODUCTION

When user adds a PCIE display adapter, it can be integrated with IGD
to show better performance. To make the two video devices work
simultaneously and normally, please refer to the following setting.

4.2 AMD DUAL GRAPHICS REQUIREMENT

Operating System: Windows Vista / Windows 7

Supported DUAL Graphics Combinations:

APU

GFX

HD 6670 Attach Only (No DG)

HD 6570 Attach Only (No DG)

HD 6450

HD 6350

Note:

“Attach Only (No DG)” indicates supported discrete graphics attachment

without Dual Graphics.

E-Series CPU do not support Dual Graphics.

Notice:

Single Channel or unbalanced memory does not support Dual Graphic function.
Please use at least DDR3-1333 4G (2G+2G).

A4-Series
HD 6410D

A6-Series
HD 6530D

Y Y Y

Y

Attach Only (No DG) Attach Only (No DG)

A8-Series”

HD 6550D

Y Y

Y Y

18

NOTE

The information described above in this manual is for your reference only and
the actual information and settings on board may be different from this manual.
For further AMD Dual Graphics information, please visit the following website:

http://www.amd.com

4.3 AMD DUAL GRAPHICS SETUP

Step 1: Insert Dual Graphics-Ready graphics card into PEX16_1 slot.

Step 2: Set the BIOS setting as follows:

[Chipset]→[North Bridge]→[Surround View]→[Enabled]

Step 3: Install Driver DVD Chipset Driver, and reboot the system. Activate AMD

VISION Engine Control Center to make sure CrossFire has been
enabled.

A75MG

19

Motherboard Manual

CHAPTER 5: RAID FUNCTIONS

5.1 O

Supports Windows Vista and Windows 7.

PERATING SYSTEM

5.2 RAID ARRAYS

RAID supports the following types of RAID arrays:

RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for

many applications.

RAID 1: RAID 1 defines techniques for mirroring data.

RAID 10: RAID 10 combines the techniques used in RAID 0 and RAID 1.

5.3 HOW RAID WORKS

RAID 0:

The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks
up a large f i le into sma ller blocks an d pe rfo rms disk r ead s and writes acr oss multip le
drives in parallel. The size of each block is determined by the stripe size parameter,
which you set during the creation of the RAID set based on the system environment. This
technique reduces overall disk access time and offers high bandwidth.

Features and Benefits

 Drives: Minimum 2, and maximum is up to 6 or 8. Depending on the

platform.

 Uses: Intended for non-critical data requiring high data throughput, or any

environment that does not require fault tolerance.

 Benefits: provides increased data throughput, especially for large files. No

capacity loss penalty for parity.

 Drawbacks: Does not deliver any fault tolerance. If any drive in the array

fails, all data is lost.

 Fault Tolerance: No.

20

Block 1
Blo ck 3
Blo ck 5

Block 2
Blo ck 4
Blo ck 6

A75MG

RAID 1:

Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1
array system. The mirrored (backup) copy of the data can reside on the same disk or on a
second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the
active volume or drive is corrupted or becomes unavailable because of a hardware failure.

RAID techniques can be applied for high-availability solutions, or as a form of automatic
backup that eliminates tedious manual backups to more expensive and less reliab le
media.

Features and Benefits

 Drives: Minimum 2, and maximum is 2.
 Uses: RAID 1 is ideal for small databases or any other application that

requires fault tolerance and minimal capacity.

 Benefits: Provides 100% data redundancy. Should one drive fail, the

controller switches to the other drive.

 Drawbacks: Requires 2 drives for the storage space of one drive.

Performance is impaired during drive rebuilds.

 Fault Tolerance: Yes .

Block 1
Block 2
Block 3

Block 1
Block 2
Block 3

21

Motherboard Manual

RAID 10:

RAID 1 drives can be stripped using RAID 0 techniques. Resulting in a RAID 10
solution for improved resiliency, performance and rebuild performance.

Features and Benefits

 Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.
 Benefits: Optimizes for both fault tolerance and performance, allowing for

automatic redundancy. May be simultaneously used with other RAID levels
in an array, and allows for spare disks.

 Drawbacks: Requires twice the available disk space for data redundancy,

the same as RAID level 1.

 Fault Tolerance: Yes .

22

Block 1
Block 3
Block 5

Block 1
Block 3
Block 5

Block 2
Block 4
Block 6

Block 2
Block 4
Block 6

CHAPTER 6: USEFUL HELP

A75MG

6.1 D

RIVER INSTALLATION NOTE

After you installed your operating system, please insert the Fully Setup
Driver DVD into your optical drive and install the driver for better system
performance.

You will see the following window after you insert the DVD

The setup guide will auto detect your motherboard and operating system.

Note:

If this window didn’t show up after you insert the Driver DVD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation

To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.

B. Software Installation

To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.

C. Manual

Aside from the paperback manual, we also provide manual in the Driver
DVD. Click on the Manual icon to browse for available manual.

Note:

You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader so ftware from
http://www.adobe.com/products/acrobat/readstep2.html

23

Motherboard Manual

e

6.2 SOFTWARE

Installing Software

1. Insert the Setup DVD to the optical drive. The drivers installation
program would appear if the Autorun function has been enabled.

2. Select Software In stallation, and then click on the respective software
title.

3. Follow the on-screen instructions to complete the installation.

Launching Software

After the installation process, you will see the software icon “eHOT Line” /
“BIOS Update” appears on the desktop. Double-click the icon to launch the
utility.

eHot-Line (Optional)

eHot-Line is a convenient utility that helps you to contact with our
Tech-Support system. This utility will collect the system information which is
useful for analyzing the problem you may have encountered, and then send
these information to our tech-support department to help you fix the problem.

Before you use this uti lity, please set Outlook Express as your default e- mail c lient app licatio n progra m.

re pr es ent s im porta nt

*

information that you
must provide. Without
this inf ormation, you may
not be able to send out
the mail.

This block will show
the information which
would be collected in
the mail.

Describe condition

*

of your system.

Select your area or

*

the area cl os e to you.

Provide the e-mail
address that you would
like to s end the copy to.

Pr ovid e the na me of

*

the memor y module
manufacturer.

Provide the name of
th e powe r su ppl y
manufacturer and the
model no.

Se nd th e mai l out .

Sav e thes e in forma tion to a .txt fil

Exit this dialog.

24

A75MG

After filling up this information, click “Send”
to send the mail out. A warning dialog would
appear asking for your confirmation; click

“Send” to confirm or “Do Not Send” to cancel.

If you want to save this information to a .txt file, click “Save As…” and then you
will see a saving dialog appears asking you to enter file name.

Enter the file name and then click
“Save”. Your system information

will be saved to a .txt file.

Open the saved .txt file, you will see
your system information including
motherboard/BIOS/CPU/video/
device/OS information. This
information is also concluded in the
sent mail.

We will not share customer’s data with any other third parties,
so please feel free to provide your system information while using
eHot-Line service.

If you are not using Outlook Express as your default e-mail client
application, you may need to save the system information to a .txt file
and send the file to our tech support with other e-mail application.
Go to the following web

http://www.biostar.com.tw/app/en-us/about/contact.php for getting

our contact information.

25

Motherboard Manual

BIOS Update

BIOS Update is a convenient utility which allows you to update your
motherboard BIOS under Windows system.

AWARD BIOS AMI BIOS

Clear CMOS function

(Only for AWARD BIOS)

Show current BIOS information

Save cur rent B IOS

to a .bin file

Update BIOS

with a BIOS file

<Backup BIOS>

Once click on this button, the saving

dialog will show. Choose the

position to save file a nd enter file

name. (We recommend that the file

name should be English/number

and no longer than 7 characters.)

Then click Save.

26

A75MG

<Update BIOS>

Before doing this, please download the proper BIOS file from the website.

For AWARD BIOS, update BIOS procedure
should be run with Clear CMOS function, so
please check on Clear CMOS first.

Then click Update BIOS button, a
dialog will show for asking you backup
current BIOS. Click Yes for BIOS
backup and refer to the Backup BIOS
procedure; or click No to skip this
procedure.

After the BIOS Backup procedure, the
open dialog will show for requesting the
BIOS file which is going to be updated.
Please choose the proper BIOS file for
updating, then click on Open.

The utility will update BIOS with the
proper BIOS file, and this process may
take minutes. Please do not open any
other applications during this process.

After the BIOS Update process, click on
OK to restart the system.

While the system boots up and the full screen logo shows, press <Delete>
key to enter BIOS setup.

In the BIOS setup, use the Load Optimized Defaults function and then Save and
Exit Setup to exit BIOS setup. BIOS Update is completed.

All the information and content above about the software are subject to be changed
without notice. For better performance, the software is being co ntinuously updated.
The information and pictures described above are for your reference only. The actual
information and settings on board may be slightly different from this manual.

27

Motherboard Manual

6.3 EXTRA INFORMATION

CPU Overheated

If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.

When the CPU is over heated, the motherboard will shutdow n
automatically to avoid a damage of the CPU, and the system may not
power on again.

In this case, please double check:

1. The CPU cooler surface is placed evenly with the CPU surface.

2. CPU fan is rotated normally.

3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU protection
function.

1. Remove the power cord from power supply for seconds.

2. Wait for seconds.

3. Plug in the power cord and boot up the system.

Or you can:

1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)

2. Wait for seconds.

3. Power on the system again.

28

A75MG

BIO-Flasher

BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to
update your BIOS via USB pen drive or floppy disk.

The BIO-Flasher is built in the BIOS chip. To enter the utility, press <F12>
during the Power-On Self Tests (POST) procedure while booting up.

Updating BIOS with BIO-Flasher

1. Go to the website to download the latest BIOS file for the motherboard.

2. Then, save the BIOS file into a USB pen drive or a floppy disk.

3. Insert the USB pen drive or the floppy disk that contains the BIOS file to the
USB port or the floppy disk drive.

4. Power on or reset the computer and then
press <F12> during the POST process.
A select dialog as the picture on the right
appears.
Select the device contains the BIOS file and
press <Enter> to enter the utility.

5. The utility will show the BIOS
files and their respective
information. Select the proper
BIOS file and press <Enter>
then <Y> to perform the BIOS
update process.

6. After the update process, the utility will ask you to reboot the system.
Press <Y> to proceed. BIOS update completes.

z This utility only allows storage device with FAT32/16 format and single

parti tion.

z Shutting down or resetting the system while updating the BIOS will lead to

system boot failure.

29

Motherboard Manual

6.4 AMI BIOS BEEP CODE

Boot Block Beep Codes

Number of Beeps Description

1 No media present. (Insert diskette in floppy drive A:)

2

3 Insert next diskette if multiple diskettes are used for recovery
4 Flash Programming successful
5 File read error

7 No Flash EPROM detected
10 Flash Erase error
11 Flash Program error
12 “AMIBOOT.ROM” file size error

13

POST BIOS Beep Codes

Number of Beeps Description

1 Memory refresh timer error

3 Base memory read/write test error

6 Keyboard controller BAT command failed

7 General exception error (processor exception interrupt error)

8 Display memory error (system video adapter)

“AMIBOOT.ROM” file not found in root directory of diskette in
A:

BIOS ROM image mismatch (file layout does not match
image present in flash device)

Troubleshooting POST BIOS Beep Codes

Number of Beeps Troubleshooting Action

1, 3 Reseat the memory, or replace with known good modules.

Fatal error indicating a serious problem with the system.
Consult your system manufacturer. Before declaring the
motherboard beyond all hope, eliminate the possibility of
interference by a malfunctioning add-in card. Remove all
expansion cards except the video adapter.

6, 7

8

30

z If beep codes are generated when all other expansion

cards are absent, consult your system manufacturer’s
technical support.

z If beep codes are not generated when all other expansion

cards are absent, one of the add-in cards is causing the
malfunction. Insert the cards back into the system one at a
time until the problem happens again. This will reveal the
malfunctioning card.

If the system video adapter is an add-in card, replace or
reseat the
video adapter. If the video adapter is an integrated part of the
system board, the board may be faulty.

6.5 TROUBLESHOOTING

Probable Solution

1. There is no power in the system.
Power LED does not shine; the
fan of the power supply does not
work

2. Indicator light on keyboard does
not shine.

System is inoperative. Keyboard lights
are on, power indicator lights are lit,
and hard drives are running.

System does not boot from a hard disk
drive, but can be booted from optical
drive.

System only boots from an optical
drive. Hard disks can be read,
applications can be used, but system
fails to boot from a hard disk.

Screen message shows “Invalid
Configuration” or “CMOS Failure.”

System cannot boot after user installs a
second hard drive.

A75MG

1. Make sure power cable is
securely plugged in.

2. Replace cable.

3. Contact technical support.

Using even pressure on both ends of
the DIMM, press down firmly until the
module snaps into place.

1. Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.

2. Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.

1. Back up data and applications
files.

2. Reformat the hard drive.
Re-install applications and data
using backup disks.

Review system’s equipment. Make sure
correct information is in setup.

1. Set master/slave jumpers
correctly.

2. Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.

31

Motherboard Manual

APPENDIX: SPEC IN OTHER LANGUAGES

G

ERMAN

Sp ezif ika tio nen

CPU

Chipsatz

Super E/A

Arbeitsspeich

er

SATA III

LAN

Sockel FM1

AMD A-Series / E2-Series / Athlon II /

Sempron Prozessoren

AMD A75

ITE 8728

Biet et die h äufig ver wendeten a lten Sup er

E/A-Funktionen.

Low Pin Count-Schnittstelle

DDR3 DIMM-Steckplätze x 2

Max. 16GB Arbeitsspeicher

Jeder DIMM unterstützt 512MB/

1GB/2GB/4GB/8GB DDR3.

Integrierter Serial ATA-Controller

RTL8111F

Die AMD 64-Architektur unterstützt eine 32-B it- und

64-Bit-Datenverarbeitung

(Maximales Watt: 100W)

Umgebungskontrolle,

Hardware-Überwachung

Lüfterdrehz ahl-Cont roller

"Smart Guardian"-Funktion von ITE

Dual-Kanal DDR3 Speichermodul

Unterstützt DDR3 800/1066/1333/1600/1866

registrierte DIMMs. ECC DIMMs werden nicht

unterstützt.

Datentransferrate b is zu 6 Gb /s

Konform mit der SATA-Spezifikation Version 3.0

Unterstützt RAID 0,1,10

10 / 100 / 1000 Mb/s Auto-Negotiation

Halb-/ Vollduplex-Funktion

Audio-Codec

USB3.0

Steckplätze

Onboard-Ans

chluss

32

ALC662

A75 Datenübertragungsraten bis zu 600 MB / s

PCI Express Gen2 x16 Steckplatz x1

PCI Steckplatz x1

SATA-Anschluss x4 Jeder Anschluss unterstützt 1 SATA-Laufwerk

Fronttafelanschluss x1 Unterstützt die Fronttafelfunktionen

Front-Audioanschluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion

CPU-Lüfter-Sockel x1

5.1-Kanal-Audioausgabe

Unterstützt High-Definition Audio

CPU-Lüfterstromversorgungsanschluss (mit Smart

Fan -F un ktio n)

A75MG

Sp ezif ika tio nen

System-Lüfter-Sockel x1 System-Lüfter-Stromversorgungsanschluss

"CMOS löschen "-So cke l x1

USB2.0-Anschluss x2 Jeder Anschluss unterstützt 2

Front taf el- USB 2.0-Ans chlü ss e

USB3.0-Anschluss x1 Jeder Anschluss unterstützt 2

Front taf el- USB 3.0-Ans chlü ss e

Druckeranschluss Anschluss x1 Jeder Anschluss unterstützt 1 Druckeranschluss

Serieller Anschluss x1

Stromanschluss (24-polig) x1

St r oman s chluss (4-pol ig ) x1

Rückseiten-E

/A

Platinengröße

OS-Unterstüt

zung

PS/2-Tastatur / Maus x1

VGA-Anschluss x1

DVI-D-Anschluss x1

LAN-Anschluss x1

USB2.0-Anschluss x2

USB3.0-Anschluss x2

Audioanschluss x3

192 mm (B) X 235.48 mm (L)

Windows XP / Vista / 7

Biostar behält sich das Recht vor, ohne Ankündigung

die Unterstützung für ein Betriebssystem

hinzuzufügen oder zu entfernen.

33

Motherboard Manual

FRENCH

SPEC

UC

Chipset

Socket FM1

Processeurs AMD A-Series / E2-Series /

Athlon II / Sempron

AMD A75

L'architecture AMD 64 permet le calcul 32 et 64 bits

(Watt maximum : 100W)

Super E/S

Mémoire

principale

SATA III

LAN

Codec audio

USB3.0

Fentes

ITE 8728

Fournit la fonctionnalité de Super E/S

patrimoniales la plus utilisée.

Int e rface à f aib le co mpte de b roches

Fentes DDR3 DIMM x 2

Capacité mé mo ire max ima le de 16Go

Chaque D IMM prend en charg e des DDR3

de 512Mo/1Go/2Go/4Go/8 Go

Contrô leur Serial ATA int é gr é

RTL8111F

ALC662

A75 Taux de transfert de données jusqu'à 600 Mo / s

Fente PCI Express Gen2 x16 x1

Fente PCI x 1

Initiatives de contrôle environnementales,

Mon iteur d e mat ér iel

Contrôleur de vitesse de ventilateur

Fonction "Gardien intelligent" de l'ITE

Modu le d e mé mo ire DDR3 à mo d e à do uble vo ie

Prend en charge la DDR3 800/1066/1333/1600/1866

Les DIMM à registres et DIMM avec code correcteurs

d'erreurs ne sont pas prises en charge

Taux de transfert jusqu'à 6 Go/s.

Co nforme à l a s p écificat ion SATA Ver s ion 3.0

Prise en charg e RAID 0,1,10

10 / 100 / 1000 Mb /s négo ciat ion automatique

Half / Full duplex capability

Sortie audio à 5 .1 vo ies

Prise en ch arg e de l'audio haute déf in it ion

Connecteur
embarqu é

Connecteur SATA x4

Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant

Connecteur Audio du panneau avant x1 Prend en charge la fonction audio du panneau avant

Embase de ventilateur UC x1

Chaque connecteur pr end en ch arg e 1 périp hér iqu e

SATA

Alimentation électrique du ventilateur UC (avec fonction

de ventilateur intelligent)

34

A75MG

SPEC

Embase de ventilateur système x1 Alimentation électrique du ventilateur système

Embase d'effacement CMOS x1

E/S du

panneau
arrière

Dimensions
de la carte

Connecteur USB2.0 x2

Connecteur USB3.0 x1

Connecteur de Port d'imprimante x1 Chaque connector prend en charge 1 Port d'imprimante

Port série x1

Connecteur d'aliment at ion x1

(24 broches)

Connecteur d'aliment at ion x1

(4broch es)

Clavier / Souris PS/2 x1

Port VGA x1

Port DVI-D x1

Port LAN x1

Port US B2.0 x2

Port US B3.0 x2

Fiche aud io x 3

192 mm (l) X 235.48 mm (H)

Chaque connecteur prend en charge 2 ports USB2.0 de

panneau avant

Chaque connecteur prend en charge 2 ports USB3.0 de

panneau avant

Support SE

Windows XP / Vista / 7

Biostar se réserve le droit d'ajouter ou de supprimer le

support de SE avec ou sans préavis.

35

Motherboard Manual

ITALIAN

Socket FM1

CPU

Processori AMD A-Series / E2-Series /

SPECIFICA

L’archit ett u ra AMD 64 abilita la co mput azione 32

e 64 bit

Athlon II / Sempron

Chipset

Super I/O

Memoria

principale

SATA III

LAN

Codec

audio

USB3.0 A75 Velocità di trasferimento dati fino a 600 MB / s

AMD A75

ITE 8728

Fo rnis ce le f unz ion al it à leg a cy Super

I/O usate più comunemente.

Interfaccia LPC (Low Pin Count)

Alloggi DIMM DDR3 x 2

Capacità mass ima della memoria 16GB

Ciascun DIMM supporta DDR3

512MB/1GB/2GB/4GB/8GB

Co ntroller Ser ia l ATA in t eg rato

RTL8111F

ALC662

(Watt massimo : 100W)

Funzioni di controllo dell’ambiente:

Monitoraggio hardware

Co ntroller velo c it à ventolin a

Funzione "Smart Guardian" di ITE

Modulo di memoria DDR3 a canale doppio

Supporto di DDR3 800/1066/1333/1600/1866

DIMM registrati e DIMM ECC non sono supportati

Velocità di trasferimento dei dati fino a 6 Gb/s.

Co mp at ib ile s p ec if iche S ATA Vers ione 3.0

Supporto RAID 0,1,10

Negoziazione automatica 10 / 100 / 1000 Mb/s

Capacità Half / Full Duplex

Uscita audio 5.1 canali

Supporto audio High-Definition (HD)

Allo g g i

Connettori

su scheda

36

Alloggio PCI Express Gen2 x16 x1

Allo g g io PC I x 1

Connettore SATA x4 Ciascun connettore supporta 1 unità SATA

Co nnett o re pannello fr ontale x 1 S upport a i s ervizi del pann e llo fr ontale

Connettore audio frontale x1 Supporta la funzione audio pannello frontale

Alimentazione ventolina CPU (con funzione Smart

Co lletto r e ventolina C PU x1

Fan)

Co lletto r e ventolina sistema x1 Alimentazione vent o lina d i s is t ema

SPECIFICA

Co lletto r e cance llaz ione CMOS x 1

A75MG

I/O

pannello

posteriore

Dimension

i scheda

Connettore USB2.0 x2

Connettore USB3.0 x1

Connettore Porta stampante x1 Ciascun connettore supporta 1 Porta stampante

Porta seriale x1

Connettore alimentaz ione x1

(24 pin)

Connettore alimentaz ione x1

(4pin)

Tastiera / Mouse PS/2 x1

Porta VGA x1

Porta DVI-D x1

Porta LAN x1

Porta USB2.0 x2

Porta USB3.0 x2

Connettore audio x3

192 mm (larghezza) x 235.48 mm

(altez za)

Ciascun connettore supporta 2 porte USB2.0

pannello frontale

Ciascun connettore supporta 2 porte USB3.0

pannello frontale

Sistemi

operativi

supportati

Windows XP / Vista / 7

Biostar si riserva il diritto di aggiungere o

rimuovere il supporto di qualsiasi sistema

operativo senza preavviso.

37

Motherboard Manual

SPANISH

Especificación

CPU

Conjunto de

chips

Súper E/S

Memoria

principal

SATA III

Red Local

Conector FM1

Proc esadores AMD A-Ser ies / E2-Ser ies /

Athlon II / Sempron

AMD A75

ITE 8728

Le ofrece las funcionalidades heredadas de

us o más comú n Súper E /S.

Interfaz de cuenta Low Pin

Ranuras DIMM DDR3 x 2

Capacidad máxima de memoria de 16GB

Cada DIMM admite DDR de

512MB/1GB/2GB/4GB/8GB

Controlador ATA Serie Integrado

RTL8111F

La arquitectura AMD 64 permite el procesado de 32 y

64 bits

(Vatio máximo: 100W)

In iciat ivas d e cont rol d e entorno,

Monitor hardware

Controlador de velocidad de ventilador

Función "Guardia inteligente" de ITE

Módulo de memoria DDR3 de canal Doble

Admite DDR3 de 800/1066/1333/1600/1866

No admite DIMM registrados o DIMM compatibles con

ECC

Tasas de transferencia de hasta 6 Gb/s.

Co mp at ible co n la ve rsión S ATA 3 .0

Admite RAID 0,1,10

Negociación de 10 / 100 / 1000 Mb/s

Funciones Half / Full dúplex

Códecs de

sonido

USB3.0

Ranuras

Conectores

en p laca

38

ALC662

A75 Tasas de transferencia de datos hasta 600 MB / s

Ranura PCI Express Gen2 x16 X1

Ranura PCI X1

Conector SATA X4 Cada conector soporta 1 dispositivos SATA

Co nector de p ane l f ronta l X1 S o port a ins t a la c io nes en e l p anel front a l

Conector de sonido frontal X1 Soporta funciones de sonido en el panel frontal

Cabecera de ventilador de CPU X1 Fuente de alimentación de ventilador de CPU (con

Salida de sonido de 5.1 canales

Soporte de sonido de Alta Definición

función Smart Fan)

A75MG

Especificación

Cabecera de ventilador de sistema X1 Fuente de alimentación de ventilador de sistema

Cabecera de borrado de CMOS X1

Conector USB2.0 X2 Cada conector soport a 2 puertos USB2.0 fronta les

Conector USB3.0 X1 Cada conector soport a 2 puertos USB3.0 fronta les

Conector Puerto de impresora X1 Cada conector soporta 1 Puerto de impresora

Puert o serie X1

Panel

trasero de

E/S

Ta maño d e

la placa

Soporte de

sistema

operativo

Conector de alimentación X1

(24 patillas)

Conector de alimentación X1

(4patillas)

Teclado / R atón PS/2 X1

Puert o VGA X1

Puerto DV I-D X1

Puerto de red local X1

Puert o USB 2.0 X2

Puert o USB 3.0 X2

Conector de sonido X3

192 mm. (A) X 235.48 mm. (H)

Windows XP / Vista / 7

Biostar se reserva el derecho de añadir o retirar el

soporte de cualquier SO con o sin aviso previo.

39

Motherboard Manual

PORTUGUESE

Socket FM1

CPU

Chipset

Processadores AMD A-Series / E2-Series /

Athlon II / Sempron

AMD A75

ESPECIFICAÇÕES

A arq uite ctura AMD 64 p ermite uma co mput ação d e 32

e 64 bits

(Watt máximo: 10 0W)

Especificaçã

o Super I/O

Memória

principal

SATA III

LAN

Codec de

som

ITE 8728

Proporciona as funcionalidades mais

utilizadas em termos da especificação

Super I/O.

Interface LPC (Low Pin Count).

Ranhuras DIMM DDR3 x 2

Capacidad e máx ima de me mória: 16GB

Cada módulo DIMM suporta uma

memória DDR3 de 512 MB/

1GB/2GB/4GB/8GB

Controlador Serial ATA integrado

RTL8111F

ALC662

In iciat ivas p ara con t ro lo d o a mb iente

Monitorização do hardware

Controlador da velocidade da ventoinha

Função "S mart Gu ardian" d a ITE

Módulo de memória DDR3 de canal duplo

Suporta módulos DDR3 800/1066/1333/1600/1866

Os módulos DIMM registados e os DIMM ECC não são

suportados

Velocidades de transmissão de dados até 6 Gb/s.

Compat ib ilidad e co m a especif ica ção SATA versão 3.0

Suporta as funções RA ID 0,1,10

Auto negociação de 10 / 100 / 1000 Mb/s

Capacidade semi/full-duplex

Saída de áudio de 5.1 canais

Suporta a especificação High-Definition Audio

USB3.0

Ranhuras

Conectores

na placa

A75 Taxas de transferência de dados até 600 MB / s

Ranhura PCI Express Gen2 x16 x1

Ranhura PCI x1

Conector SATA x4 Cada conector suporta 1 dispositivo SATA

Conector do painel frontal x1 Para suporte de várias funções no painel frontal

Conector de áud io frontal x1 Suporta a fun ção de áud io no paine l frontal

40

ESPECIFICAÇÕES

Aliment ação da vento inha d a CPU (com a função S mart

Conector da ventoinha da CPU x1

Fan )

Conector da ventoinha do sistema x1 Alimentação da ventoinha do sistema

Conector para limpeza do CMOS x1

A75MG

Entradas/S

aídas no

painel

traseiro

Tamanho

da placa

Conector USB2.0 x2

Conector USB3.0 x1

Conector da para impressora x1 Cada conector suporta 1 Porta para impressora

Porta s ér ie x1

Conector de alimentação x1

(24 pinos)

Conector de alimentação x1

(4 p inos)

Teclado / R ato PS/2 x1

Porta VGA x1

Porta DVI-D x 1

Porta LAN x1

Porta USB2.0 x2

Porta USB3.0 x2

Tomada de áudio x3

192 mm (L) X 235.48 mm (A)

Cada conector suporta 2 portas USB2.0 no painel

frontal

Cada conector suporta 2 portas USB3.0 no painel

frontal

Sistemas

operativos

suportados

Windows XP / Vista / 7

A Biostar reserva-se o direito de adicionar ou remover

suporte para qualquer sistema operativo com ou sem

av is o prévio.

41

Motherboard Manual

POLISH

SPEC

Procesor

Chipset

Pamięć

główna

Super I/O

SATA III

LAN

Socket FM1

AMD A-Series / E2-Series / Athlon II /

Sempron Procesory

AMD A75

Gniazda DDR3 DIMM x 2

Maks. wielkość pamięci 16GB

Każde gniazdo DIMM obs ługuje moduły

512MB/1GB/2GB/4GB/8GB DDR3

ITE 8728

Zapewnia najbardziej powszechne funkcje

Super I/O.

Interfejs Low Pin Count

Zintegrowany kontroler Serial ATA

RTL8111F

Architektura AMD 64 umożliwia przetwarzanie 32 i 64

bitowe

(Maksymalny Watt: 100W)

Mod uł pamięci DDR3 z trybem podwójnego kanału

Obsługa DDR3 800/1066/1333/1600/1866

Brak obsług i Register ed DIMM oraz ECC D IMM

Funkcje kontroli warunków pracy,

Mon itor H /W

Kontroler prędkości wenty lato ra

Funkcja ITE "Smart Guardian"

Transfer danych do 6 Gb/s.

Zgodność ze specyfikacją SATA w wersj i 3. 0

Obsługa RAID 0,1,10

10/100/1000Mb/s z automatyczną negocjacją

szybkości

Kodek

dźwiękowy

USB3.0

Gniazda

Złącza

wbud owane

42

Działanie w tryb ie połowicznego/pełnego dupleksu

ALC662

A75 Cena transferu danych do 600 MB / s

Gniazdo PCI Express Gen2 x16 x1

Gniazdo PCI x1

Złącze SATA x4 Każde złącze obs ługuje 1 urządzenie SATA

Złącze panela przedniego x1 Obsługa elementów panela przedniego

Przedn ie złącze aud io x1 Obsługa funkcji audio na panelu przednim

Złącze główkowe wenty lat ora

procesora x1

5.1 kanałowe wyjście audio

Obsługa H ig h-Def in it io n Aud io

Zasilanie wentylatora procesora (z funkcją Smart Fan)

SPEC

Złącze główkowe wenty lat ora

Zasilanie wentylatora systemowego

systemowego x1

A75MG

Back Panel

I/O

Wymiary

płyty

Obsluga

systemu

operacyjne

go

Złącze główkowe kasowan ia

CMOS x1

Złącze USB2.0 x2

Złącze USB3.0 x1

Złącze Port drukarki x1 Każde złącze obs ługuje 1 Port drukarki

Port szeregowy x1

Złącze zasilania (24 pinowe) x1

Złącze zas ilania (4 p ino we) x1

Klaw iatura / Mysz PS/2 x1

Port VGA x1

Port DVI-D x1

Port LAN x1

Port US B2.0 x2

Port US B3.0 x2

Gniazdo audio x3

192 mm (S) X 235.48 mm (W)

Windows XP / Vista / 7

Każde złącze obs ługuje 2 porty USB2.0 na panelu

przednim

Każde złącze obs ługuje 2 porty USB3.0 na panelu

przednim

Biostar zastrzega sobie prawo dodawania lub

odwoływ ania obsług i dowo lnego s ystemu

operacyjnego bez powiado mienia.

43

Motherboard Manual

RUSSIAN

CPU

(центральн

ый

процессор)

Набо р
микросхем

Основная
память

Super I/O

SATA III

Локальная
сеть

Звуко во й
кодек

USB3.0

Слоты

Встроенны

й разъём

Гнездо FM1

Процессоры AMD A-Series / E2-Series /

Athlon II / Sempron

AMD A75

Слоты DDR3 DIMM x 2

Максимальная ёмкос ть памяти 16ГБ

Каждый модуль DIMM поддерживает

512МБ /1ГБ/2ГБ /4ГБ/8ГБ DDR3

ITE 8728

Обеспечивает наиболее используемые

действующие фун кц ио н ал ьн ы е

возможности Super I/O.

Интерфейс с низ ким коли чество м выводов

Встроенное последовательное устройство

упра вления ATA

RTL8111F

ALC662

A75 скорости передачи данных до 600 МБ / с

Слот PCI Express Gen2 x16 x1

Слот PCI x1

Разъ ём SATA x4 Каждый разъём поддерживает 1 устройс тво SATA

Разъ ём на лицевой панели x1 Поддержка устройс тв на лицевой панели

Входной звуковой разъём x1

Контактирующее приспособление

вентил ятора центрального процессора x1

СПЕЦ

Арх итектур а AMD 64 разрешать обработка

данных на 32 и 64 бит

(Максим ал ьн ый ватт: 100W)

Мод уль памяти с д вух кан альным режимом DDR3

Поддержка DDR3 800/1066/1333/1600/1866

Не поддерживает зарегистрированные модули

DIMM and ECC DIMM

Инициативы по охране окружающей среды,

Аппаратный монитор

Регул ятор скорости

Функц ия ITE "Smart Guard ian "

(Интеллектуальная защита)

скорость передачи данных до 6 гигабит/с.

Соответствие спецификации SATA версия 3.0

Поддержка RAID 0,1,10

Автоматическо е согл асование 10/ 100/ 1000 Мб/с

Частичная / полна я дуплексная способность

Звуко ва я поддержка High- Def in it io n

5.1канальный звуковой вых од

Поддержка звуко вых функций на лицевой

панели

Источник питания для вентилятора центрального

процессора (с функц и ей интеллектуального

вентил ятора)

44

СПЕЦ

Контактирующее приспособление

вентил ятора системы x1

Открытое контактир ующ ее

приспособление CMOS x1

Источник пит ания для вентилято р а системы

A75MG

Задняя

панель
средств
ввода-выв

ода

Разм ер
панели

Поддержка

OS

USB2.0-разъём x2

USB3.0-разъём x1

Разъ ём Порт подключения

принтера x1

Последоват ельны й порт x1

Разъ ем питания (24 вы во д) x1

Разъ ем питания (4 вы вод) x1

Клавиатура / Мышь PS /2 x 1

Пор т VGA x1

Пор т DVI-D x1

Пор т LAN x1

USB2.0-порт x2

USB3.0-порт x2

Гнездо для подключени я

наушников x3

192 мм (Ш) X 235.48 мм (В)

Windows XP / Vista / 7

Каждый разъём поддерживает 2 USB2.0-порта на

лицевой панели

Каждый разъём поддерживает 2 USB3.0-порта на

лицевой панели

Каждый разъём поддерживает 1 По рт

подключения принтера

Biostar сохраняет за собой право добавлять или

удаля ть средства обеспечения для OS с или без

предварительного уведомле ния.

45

Motherboard Manual

ARABIC

ﺔﻴﻨﻘﺗ ﻦﻜﻤﺗAMD 64 ﺔﻋﺮﺴﺏ ﺔﻴﺏﻮﺳﺎ ﺤﻟا تﺎﻴﻠﻤﻌﻟا ءاﺮﺝإ 32 و64 ﺖﺏ

(طاو ىﻮﺼﻗ: 100و)

تﺎﻔﺻاﻮﻤﻟا

ﺲﺒﻘﻡFM1

تﺎﺠﻟﺎﻌﻡAMD A-Series / E2-Series / Athlon II /

Sempron

AMD A75

ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو

ﺔﻳﺰآﺮﻤﻟا

ﺢﺋاﺮﺸﻟا ﺔﻋﻮﻤﺠﻡ

عﻮﻥ ﻦﻡ ةﺮآاﺬﻟا ﻢﻋﺪﺗDDR3 تﺎﻌﺳ 800/1066/1333/1600/1866

تﻻﺪﻌ ﻣ ﻞﻘﻧ تﺎﻧﺎﻴﺑ ﻞﺼﺗ ﻰﻟإ 600 ﺎﻐﻴﻣ ﺖیﺎﺑ / ﺔﻴﻧﺎﺛ

ةﺮآاذ ةﺪﺣوDDR3 ﻘﻟا ﺔﺝودﺰﻡةﺎﻨ

ﺖﻳﺎﺏ ﺎﺠﻴﻡ

ﺎﻗر ﻢﻋﺪﺗ ﻻ ةﺮآاﺬﻟا ﻖﺋ DIMM ﻊﻡ ﻖﻓاﻮﺘﺗ ﻻ ﻲﺘﻟا ﻚﻠ ﺗو ECC

ﺔﺌﻴﺒﻟا ﻲﻓ ﻢﻜﺤﺘﻟا ﻞﺋﺎﺳو:

ةﺰﻬﺝﻷا ﺔﻟﺎﺣ ﺔﻓﺮﻌﻤﻟ ﺐﻗاﺮﻡ

ﺔﺣوﺮﻤﻟا ﺔﻋﺮﺳ ﻲﻓ ﺐﻗاﺮﻡ

ﺔﻔﻴﻇو"S mart Gu ard ian" ﻦﻡ IT E

ﻰﻟإ ﻞﺼﺗ تﺎﻋﺮﺴﺏ تﺎ ﻥﺎﻴﺒﻟا ﻞﻘﻥ6ﺖﺏﺎﺠﻴﺝ /ﺔﻴﻥﺎﺙ

تﺎﻔﺹاﻮﻤﻟ ﺔﻘﺏﺎﻄﻡSATA راﺪﺹﻹا 3.0

ﺔﻴﻨﻘ ﺗ ﻢﻋﺪﺗRAID 0,1,10

ﻲﺋﺎﻘﻠﺗ ضو ﺎﻔﺗ10/100/1000 ﺖﻳﺎﺏ ﺎﺠﻴﻡ /ﺔﻴﻥﺎﺙ

ﺔﻴﻧﺎﻜﻣإ ﻞﻘﻨﻟا جودﺰﻤﻟا ﻞﻣﺎﻜﻟا/ﻲﻔﺼﻨﻟا

ﻦﻡ ﻒﻳﺮﻌﺘﻟا ﻲﻟ ﺎﻋ تﻮﺼﻟا ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗ

5.1 تﻮﺼﻟا جﺮﺨﻟ تاﻮﻨﻗ

ىﻮﺼﻗ ةﺮآاذ ﺔﻌﺳ16 ﺖﻳﺎﺏ ﺎﺠﻴﺝ

ﺔﺤﺘﻓ ﻞآ ﻢﻋﺪﺗDIMM عﻮﻥ ﻦﻡ ةﺮآاذ ﻢﻋﺪﺗ DDR3 ﺔﻌﺳ

ﺔﻔﻴﻇ و ﺮﻓﻮﺗSuper I/O ًﺎ ﻡ ا ﺪ ﺨ ﺘ ﺳ ا ﺮﺜآﻷا .

ﺗﻢﻋﺪ ﺔﻴﻨﻘﺗ Low Pin Co unt Interface

ﻢﻜﺤﺘﻡSerial ATAﻞﻡﺎﻜﺘﻡ

RTL8111F

ﺔﺤﺘﻓDDR3 DIM M دﺪﻋ2

/512 ﺎﺠﻴﻡ

و ﺖﻳﺎﺏ1/و 2/و 4/و 8 ﺎﺠﻴﺝﺖﻳﺎﺏ

ITE 8728

ALC662

A75

ﺔﺤﺘﻓGen2 x16 PCI Express دﺪﻋ1

ﺔﺤﺘﻓPCI ﺪﻋ1

ﺬﻔﻨﻡSATA دﺪﻋ4 ةﺰﻬﺝأ ﻦﻡ ﺪﺣاو ﺬﻔﻨﻡ ﻞآ ﻢﻋﺪﻳSATA

ﻨﻡﺔﻴﻡﺎﻡﻷا ﺔﺣﻮﻠﻟا ﺬﻔ دﺪﻋ1 ﺔﻴﻡﺎﻡﻷا ﺔﺣﻮﻠﻟا تاﺰﻴﻬﺠﺗ ﻢﻋﺪﻳ

ﺬﻟا ﺔﻴﺴﻴ ﺋﺮﻟا ةﺮآا

Super I/O

SATA III

ﺔﻴﻠﺥاد ﺔﻜﺒﺵ

تﻮﺼﻟا ﻚﻳدﻮآ

USB3.0

تﺎﺤﺘﻔﻟا

ﺢﻄﺳ ﻰﻠﻋ ﺬﻓﺎﻨﻤﻟا

ﺔﺣﻮﻠﻟا

ﻲﻡﺎﻡﻷا تﻮﺼﻟا ﺬﻔﻨﻡ دﺪﻋ1 ﺔﻴﻡﺎﻡﻷا ﺔﺣﻮﻠﻟ ﺎﺏ تﻮﺼﻟا ﺔﻔﻴﻇو ﻢﻋﺪﻳ

ﺔﻳﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻡ ﺔﻠﺹو دﺪﻋ1 ﺔﻔﻴﻇو ﻊﻡ ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻤﻟ ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺘﻟSmart Fan

مﺎﻈﻨﻟا ﺔﺣوﺮﻡ ﺔﻠﺹو ﺪﻋ1 ﺮﻤﻟ ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺘﻟمﺎﻈﻨﻟا ﺔﺣو

ﺢﺴﻡ ﺔﻠﺹوCMOS دﺪﻋ1

46

تﺎﻔﺻاﻮﻤﻟا

A75MG

ﺬﻔﻨﻡUSB2.0 دﺪﻋ2 ﻲﺘﺤﺘﻓ ﺬﻔﻨﻡ ﻞآ ﻢﻋﺪﻳUSB2.0ﺔﻴﻡﺎﻡﻷ ا ﺔﺣﻮﻠﻟﺎﺏ

ﺬﻔﻨﻡUSB3.0 دﺪﻋ1 ﻲﺘﺤﺘﻓ ﺬﻔﻨﻡ ﻞآ ﻢﻋﺪﻳUSB3.0ﺔﻴﻡﺎﻡﻷ ا ﺔﺣﻮﻠﻟﺎﺏ

ﺔﻌﺏﺎﻃ ﺬﻔﻨﻡ دﺪﻋ1

ﻆﻔﺘﺤﺗBiostar نوﺪﺏ وأ رﺎﻄﺥﺈﺏ ﻞﻴﻐﺸﺗ مﺎﻈﻥ يﻷ ﻢﻋﺪﻟا ﺔﻟازإ وأ ﺔﻓﺎﺿ إ ﻲﻓ ﺎﻬﻘﺤﺏ

رﺎﻄﺥإ.

ﻲﻠﺴﻠﺴﺗ ﺬﻔ ﻨﻡ دﺪﻋ1

ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ)24سﻮﺏد( دﺪﻋ1

ﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻡ ﺔﻗﺎﻄ)4ﺲﻴﺏﺎﺏد( دﺪﻋ1

ﺢﻴﺗﺎﻔﻡ ﺔﺣﻮﻟ / سوﺎﻡPS/2 دﺪﻋ1

ﺬﻓﺎﻨﻡVG A دﺪﻋ1

ﺬﻓﺎﻨﻡDV I-D دﺪﻋ1

ﻞﺥد ﺬﻓﺎﻨﻡ/ جﺮﺥ

ﺔﻴﻠﺤﻡ لﺎﺼﺗا ﺔﻜﺒﺵ ﺬﻔﻨﻡ دﺪﻋ1

ﺔﻴﻔﻠﺨﻟا ﺔﺣﻮﻠﻟا

ﺬﻓﺎﻨﻡ2.0US B دﺪﻋ2

ﺬﻓﺎﻨﻡ3.0US B دﺪﻋ2

تﻮﺹ ﺲﺒﻘﻡ دﺪﻋ3

235.48 ﻢﻡ)ضﺮﻋ (X 192 ﻢﻡ)عﺎﻔﺗرا(

Windows XP / Vista / 7

ﺔﺣﻮﻠﻟا ﻢﺠﺣ

ﻞﻴﻐﺸﺘﻟا ﺔﻤﻈﻥأ ﻢﻋد

47

Motherboard Manual

JAPANESE

仕様

CPU

チップセット

メインメモリ

Super I/O

SATA III

LAN

Socket FM1

AMD A-Series / E2-Series / Athlon II /

Sempron プロ セッサ

AMD A75

DDR3 DIMMスロット x 2

最大メモリ容 量16GB

各DIMMは 512MB/1GB/2GB/4GB/8GB DDR3

をサポート

ITE 8728

もっとも一般 に使 用されるレ ガシーSuper I/O機

能を採用して いま す。

低ピンカウン トイ ンターフェ イス

統合シリアルATA コントロー ラ

RTL8111F

AMD 64アーキ テクチャで は、32ビットと64ビット計算が

可能です

(最高 のワット : 100W)

デュアル チ ャン ネルモードDDR3メモリモジ ュール

DDR3 800/1066/1333/1600/1866 をサ ポート

登録済みDIMMとECC DIMMはサポ ートされま せん

環境コントロ ール イニシアチ ブ、

H/Wモニ ター

ファン速度コ ント ローラ/ モニター

ITE の「スマート ガー ディアン」 機能

最高6 Gb/秒の データ転送 速度

SATAバージョン3.0仕様に準拠。

RAID 0,1,10 のサポ ート

10 / 100 / 1000 Mb/秒のオ ートネゴシ エーション

半/全二重機能

サウンド

Codec

USB3.0

スロット

オンボードコ

ネクタ

48

ALC662

A75 データ転送速 度最 大600 MB /秒の

PCI Express Gen2 x16スロット x1

PCIスロット x1

SATAコネクタ x4 各コネ クタは1つのSATAデバイス をサポ ートします

フロントパネ ルコ ネクタ x1 フロン トパネル機 能をサ ポートしま す

フロントオー ディ オコネクタ x1 フロントパネ ルオーディ オ機能をサ ポー トします

CPUファンヘッダ x1 CPUファン電源装置(スマートファン 機能を搭載 )

システムファ ンヘ ッダ x1 システ ムファン電 源装置

CMOSクリアヘッダ x1

ハイデフィニ ショ ンオーディ オのサポー ト

5.1 チ ャンネルオ ーディ オアウト

仕様

A75MG

背面パネル

I/O

ボードサイズ

USB2.0コネ クタ x2

USB3.0コネ クタ x1

プリンタポー トコ ネクタ x1 各コネ クタは1つのプリ ンタポ ートをサポ ート します

シリアルポー ト x1

電源コネクタ (24 ピン) x1

電源コネクタ (4ピン) x1

PS/2キーボード / マウス x1

VGAポート x1

DVI-Dポート x1

LANポート x1

USB2.0ポー ト x2

USB3.0ポー ト x2

オーディオジ ャッ ク x3

192 mm (幅) X 235.48 mm (高さ )

各コネクタは 2つのフロ ントパネル USB2.0ポー トをサポ

ートします

各コネクタは 2つのフロ ントパネル USB3.0ポー トをサポ

ートします

OSサポー ト

Windows XP / Vista / 7

Biostarは事前の サポートな しにOSサ ポー トを追加ま たは

削除する権利 を留 保します。

2012/03/30

49