Binatone Concept Combo 2300 User Manual

Download

USER GUIDE

Before operating this set,

please read these instructions carefully.

Concept Combo 2300

CORDED AND DIGITAL CORDLESS TELEPHONE

UK BTP Ver 3, Dec 07

Note:This guide is for the corded part only. For instructions on how to use the cordless part see the "Combo 2300 Cordless Handset" user guide.

Important note — emergency calls

The CC2300 cordless handset is not designed for making emergency calls when the mains power fails. But, if there’s a power failure, you can use the base unit telephone to

make an Emergency Call, by lifting

up the corded handset instead of using the speakerphone.

*** Before operating this set, please read these instructions carefully.

If you need help …..

Binatone Helpline (for UK only)

Monday to Friday from 9:00am to 5:00pm

Tel: 0845 345 9677

**Please note that all calls are charged at local rate Or visit our website:

http://www.binatoneonline.com

Unpacking your CC2300 system

In the box, you will find:

Ƶ the base unit telephone Ƶ a telephone line cable for the base unit Ƶ a

mains power adapter

for the base unit

Ƶ the cordless handset (up to five, depending on which CC2300 system you’ve bought)

two 1.2V 550mA rechargeable batteries and a

battery compartment cover for each handset

Ƶ up to five charger pods, each with a mains power supply for multi handset system s

Ƶ two user guides, one for the corded phone and one for the cordless handset.

Keep the packaging materials in a safe place in case you later need to transport the unit.

Keep your sales (till) receipt, which is your guarantee.

Note: After lifting the handset you will need to wait for several seconds to get dial tone, before keying in the telephone number to make the call. Also you cannot dial numbers from memories when

the mains power is off.

Binatone Help Line : 0845 345 9677 1

LCD Display

Menu/Ok

Press to access menu P

ress as “OK” key to

confirm your operation

Press to mute/

un-mute microphone

Phonebook/Back

Press to access phonebook records Press to exit present menu

R(Recall)

You may need this function

if your phone is connected

to a PBX, or if you use BT

SOS Call

Press and hold for 2 seconds to activate the SOS call

Speakerphone

Press to call or answer a call by using the speakerphone.

Microphone

For speakerphone

and answering

Where to find it

Important:

When the instruction simply say ‘press’ a button, this means you should press it briefly then

release it. When the instruction say ‘press and hold’ a button, this means you should keep i t pressed

until the display changes or you hear a tone.

Pres

messages, memos,

stored numbers or

Call

Delete(DEL)

s to delete

er Display records.

Intercom

Press to make an intercom

Up-Down(CDS)

Press to access the Caller display records and scroll through them

Press to change earpiece speakerphone volume

Press to scroll through the lists and menu options

Press to redial the last number

Press while dialing a number to insert a pause

Calling Features.

machine recording.

during a call

MUTE

M1, M2, M3

Press to call numbers stored on One Touch memory

One-touch Memory

call or to transfer a call

Binatone Help Line : 0845 345 9677 2

What's on the display?

The display of your telephone contains one line with the Time/Date and Icons, one line of numbers and one line of text.

What do the symbols mean?

Number field: shows the telephone numbers

Character field: shows the Menu, name and status of a call

Talk

x

This will display when the user picks up the handset

Ring Off

x

This will display when the ringer is set to OFF

Phonebook

x This will display when you are in the

phonebook menu

Voicemail

x

Repeat CID

x This will display when the same caller has

called more than once

New CID

x

This will display when there is a new CID entry or if one is being viewed

Sequence

x Indicates the sequence number of the CID

record

Hands free/speakerphone

x

This will display when the speakerphone is

in use

A.M.

x This will display if it is A.M., in the 12 hour

clock mode

P.M.

x

This is display if it is P.M., in the 12 hour clock mode

This will display when you have a new Voice Mail message. (This is a caller id service and is not usually available from UK network providers.)

Binatone Help Line : 0845 345 9677 3

Contents

Page

Where to find it 1

What’s on the display? 2

x What the symbols mean? 2

Read First before Use 5

x

Choosing a site

for base unit and

charger pod 5

x

Mains power connection 5

x If you have a broadband line 5

Installation and Set-up

x

Choose a suitable site for the base unit

x

Connect the mains power lead and the telephone line cord into the base unit 6

x Plug the main adaptor into your wall

socket 6

x

Connect the base unit to the telephone

line 6

Desk/Wall mount installation 7

Desk Mount 7

Wall Mount 7

Basic settings

x To set Date and Time 9

Making and answering calls 10

x

To make call

x

To make a call from redial list 10

x To make a call from caller display (CID)

list 10

x

To answer a call 10

x

To Mute or un-mute the microphone 11

x

To change the earpiece or speakerphone volume during a call 11

x

Emergency call without mains power 11

Memory/Phonebook management 12

x

To create a contact in your phonebook

Page

x

To delete a contact in the phonebook 13

x

To delete all contacts in your phonebook 14

x

To edit a contact in your phonebook 14

x

To store a last number redial in your phonebook

x

Making calls from the phonebook

x

Reviewing phonebook memory status

x

Direct Memory Call

x

To Store the telephone number

x

To Speed-Dial the telephone number

x

New CID log 17

x

To review the CID li

x To delete a Caller ID record 18

st 17

x

To delete all Caller ID records 18

x

To Store a Cal ler ID contact in phonebook 18

Ringer volume, and melody 19

x To change ringer volume 19

Using multi-handset 21

x

To make intercom calls 21

x To Transfer intercom call 21 x

To set up a three-way conference 22

SOS call function 25

x

How SOS call functipn works 25

x How to terminate SOS call function

x

To Set SOS number 25

16 16 16 16 16

x x

Caller Display (CDS)/Caller ID (CID) 17

Binatone Help Line : 0845 345 9677 4

Advanced use of your Phone 26

x

Turn key tones on/off 26

x

To Set

flash (Recall) time 26

x

To Set

Dialling Mode (Tone/Pulse) 27

x

To Set

Base to default settings 27

x

To C

hange the PIN code 28

Troubleshooting 29

Cleaning and Care 31

Declaration of Conformity 31

Guarantee and Service 32

Technical Details 33

Connection and conditions for use.

You can connect your Concept Combo 2300 to a direct exchange line (DEL) - a line connected to a local exchange, with its own phone number; to an extension on an approved compatible PBX. Do not connect the Concept Combo 2300 as an extension to a payphone.

The ringer equivalence numbers (RENs) of all instruments (phones, fax machines, etc.) connected to an exchange line must not add up to more than 4 - otherwise, one or more of them may not ring and/or answer calls correctly. The Concept Combo 2300 has a REN of 1, and most other telephones have a REN of 1 unless marked otherwise.

Binatone Help Line : 0845 345 9677 5

Read First Before Use

Choosing a site for the base unit and charger pod

The base unit and charger pod(s) should be placed on a level surface, in a position where:

x

the mains adapter plug will reach an easily accessible 230-VAC switched mains supply socket - never try to lengthen the mains power cable

x

the base unit's telephone line cable will reach your telephone line socket or extension socket

x

it is not close to a sink, bath or shower, or anywhere else where it might get wet

x it is not close to other electrical equipment - fridges, washing machines,

microwave ovens, fluorescent lights, televisions etc.

x

if the base comes into contact with liquids, disconnect it promptly and use a soft cloth to dry it; if you believe that the liquid has seeped into the unit, do not reconnect the base station. Contact the Binatone helpline.

x

it is away from hot, humid conditions and strong sunlight

Mains power connection

IMPORTANT - The CC2300 base unit must be used with the mains adapter supplied with the unit. Using any other adapter will result in non-compliance with EN60950, and will invalidate any approval given to this apparatus.

If you have a Broadband line

If you connect your telephone to a line with a broadband connection, you will need to insert a micro-filter between the telephone and the telephone line; otherwise you may get interference between the telephone and the broadband, which could cause problems.

In a home with broadband, every telephone must have a micro-filter connected, not just the one at the telephone point that your modem is connected to. If you need more broadband micro-filters, contact your broadband supplier.

Binatone Help Line : 0845 345 9677 6

Installation and Set-up

1/ Choose a suitable site for the base unit (see page 5)

2/ Connect the mains power lead and the telephone line cord into the base unit

Plug one end of the telephone line cord into the jack on the back of the base (the other end will plug into the telephone wall socket later)

3/ Plug the mains adaptor into your wall socket. If you have one or more charger pods, plug the mains adaptors accordingly

Make sure that the 230VAC, 50hz mains socket is switched OFF when you plug the mains adapter into the socket.

4/ Connect the base unit to the telephone line

Insert the telephone line plug into the socket then

See the note on page 5

switch mains power back ON.

Make sure the mains socket is switched on

—

the phone won’t work without electrical power

Binatone Help Line : 0845 345 9677 7

Desk/Wall mount installation

To place the CC2300 on a desk, connect the stand to the bottom of the phone in the slots near the rear of the base as shown below.

Desk Mount

Insert the rigid clips of the stand into the slots on the bottom of the phone (nearer the centre

of the base ). Press down firmly until the flexible clips clicks into place.

To remove the stand, (1) pinch the flexible clips, (2) pull back the stand, and then (3) slide up and forward as shown below.

To place the CC2300 on a wall, connect the stand to the bottom of the phone in the slots near the front of the base as shown below.

Wall Mount

Desk/Wall mounting continued...

Insert the rigid clips of the stand into the slots on the bottom of the phone (nearer the centre of the base). Press down firmly until the flexible clips clicks into place.

To remove the stand, (1) pinch the flexible clips, (2) pull back the stand, and then (3 slide up and forward as shown below.

Mark two points on the wall that are 77 mm apart to lay the fixing centers as shown below.

77 mm

BE CAREFUL to check that there are no electrical wires hidden in the wall. Fix two screws at the marked locations, leaving approximately 7mm between the wall and the the screw head.

Hang the telephone on the screws using the

wall mount slots. You may need to remove the

telephone from the wall and tighten the screws so that the telephone is securely fixed and does

not wobble. Place the Handset on the cradle with

the parking hook on the cradle arranged to fit in the parking recess under the earpiece on the Handset.

Binatone Help Line : 0845 345 9677 8

)

Binatone Help Line : 0845 345 9677 9

Basic settings

To set Date and Time

Press the MENU/OK button.

Then press the UP or DOWN button until "SETTINGS" is displayed.

Then press the MENU/OK to confirm.

The display wil l show “DELETE HS”,

Press the UP or DOWN button until "DATE & TIME" is displayed. Then press the MENU/OK to confirm.

The 'year' will be flashing.

Press the UP or DOWN button to set the year.

Press the MENU/OK to confirm.

The 'month' will be flashing.

ou will hear a beep and the display will show "DATE & TIME".

Press the “PHONEBOOK” button to return to the previous menu.

Press the UP or DOWN button to set the month

Press the

MENU/OK

to confirm.

The 'date' will be flashing.

Press the UP or DOWN button to set the date Press the MENU/OK to confirm.

The 'hour' will be flashing.

Press the UP or DOWN button to set the hour, including the AM/PM setting

Press the MENU/OK to confirm.

The 'minutes' will be flashing.

Press the UP or DOWN button to set the minutes. Press the MENU/OK to confirm.

Press the "PHONEBOOK" button to return to the previous menu.

The format for the date is YYYY-MM-DD, and the time is HH:MM in 12 hour format

Note:If you subscribe to Caller Display (see page 17) your SC3410 time and date settings will be automatically updated by the network when you receive an incoming call.

The Caller Display service only sends the month and date, not the year, so you may still need to set the year, as this is used to calculate the day for the answering machine time stamp.



If the time and date are set on the cordless handset, it will automatically be set on the base unit, and vice-versa.

Binatone Help Line : 0845 345 9677 10

Making and answering calls

a call

Pick up the handset and the TALK icon will appear,or press SPEAKERPHONE button and the SPEAKERPHONE icon will appear.

Also the display will show “LINE IN USE”.

Use the keypad to enter the number you wish to dial.

e a call from the redial list

The phone remembers the last 10 dial led numbers. The list is in order, with the most recent message at the top.

Press the REDIAL/PAUSE button to view the redial list.

Press the UP or DOWN button until you see the number of the person you want to call.

Press the SPEAKERPHONE button or pick up the handset to make the call.

Press the UP or DOWN button to show the first entry in the CID list.

Press the UP or

DOWN button

until you see the number of the person you

want to call.

Press

the SPEAKERPHONE button

or pick up the handset to make the call.

When the phone rings:

Pick up the handset or press the SPEAKERPHONE button to answer the call.

To make a call

To make a call from the redial list

To make a call from Caller Display (CID) list

To answer a call

When you have finished the call place the handset back on the base.

* To insert a pause in the dialling sequence, press the RD/P button, which will then show

a P in the number.

You can also make a call by using the Pre-Dialling function:

Dial the required telephone number first, and if you make a mistake you can correct it by using the DEL button to delete digits and then add the right ones. Pick up the handset or press the Speakerphone button.

The number will be dialled out automatically using the handset or speakerphone mode selected.

If your list is empty, the display will show

“EMPTY”.

Binatone Help Line : 0845 345 9677 11

During a call press the MENU/OK button and the display will show

“CALL MUTED”.

To un-mute, press the MENU/OK button and the display will show

“LINE IN USE”.

During a call press the UP button to increase or DOWN button to decrease the Volume.

The CC2300 corded base unit can make an emergency call with the corded handset when the mains AC power is disconnected.

EMERGENCY CALL WITHOUT MAINS POWER

To change the earpiece or speakerphone volume during a call

To Mute or Un-mute the microphone

x

Pick up the corded handset. After lifting the handset you will need to wait for several seconds to get dial tone, before keying in the telephone number to make the call.

x

When the mains power is off, you can also answer an incoming call with the

When the phone rings, pick up the corded handset. After lifting the handset you

It is not possible to dial numbers from memories when the mains power is off.

will need to wait for several seconds before you can hear the calling person's voice

corded handset. 

or before they can hear you.

Binatone Help Line : 0845 345 9677 12

Memory/Phonebook management

How to enter characters?

Telephone Keypad characters

To enter the characters, press the button

where you see the character e.g. if you want to insert the letter ‘A’ you press ‘2’ if you want to insert the lett er ‘B’ you press twice and f or ‘C’, three times etc. If you want to insert ‘AA’ then you will have to wait for the first ‘A’ to stop flashing then insert the second ‘A’. Press

twice for space, to delete single characters

and press and hold to delete the whole text.

DEL

1st 2nd 3rd 4th 5th 6th

_ , ?

’

”

( ) : ; .

A B C 2

D E F 3

G H I 4

J K L 5

M N O 6

P Q R S 7

T U V 8

W X Y Z 9

space 0 + - @ = / \ [ ]

? !

7th 8th 9th 10th 11th 12th 13th 14th

Binatone Help Line : 0845 345 9677 13

Press the MENU/OK button, to see “PHONE BOOK”.

Press the MENU/OK button, to see “LIST”.

Press the DOWN button, to see "NEW ENTRY".

Press the MENU/OK button and the display will show a flashing bar at the beginning of the name position.

Key in the name using the digit keys (maximum 12 characters). If you make any mistakes press DELETE button to delete.

When you have finished press the MENU/OK button to confirm, and the display

Key in the number using the digit keys (maximum 20 digits).

Press the MENU/OK button to confirm and the display will show

“MELODY 1”.

Use the UP or DOWN buttons to scroll through the melodies. (there are 10 melodies to choose from).

Press the MENU/OK button to confirm your selection. You will hear

a confirmation tone, and the display will return to “NEW ENTRY”.

*If there is no more space in the phonebook, “MEMORY FULL” will appear on the display.

Press the MENU/OK button, to see “PHONE BOOK”.

Press the MENU/OK button, to see "LIST".

Press the DOWN button repeatedly until you see

“DEL RECORD”.

Press the MENU/OK button. The display will show the first name and number in your phonebook.

To create a contact in your phonebook

To delete a contact in your phonebook

will move the flashing bar to the beginning of the number position.

If you make any mistakes use the DELETE button to delete.

The Phonebook can store up to 150 names (maximum 12 characters) and numbers

Also, you can select a different ringer melody for each entry, but this will only work if

(maximum 20 digits) in the memory.

you subscribe to CID (see page 17).

Binatone Help Line : 0845 345 9677 14

Press the MENU/OK button, to see “PHONE BOOK”.

Press the MENU/OK button, to see "LIST".

Press the DOWN button repeatedly until you see "DELETE ALL".

Press the MENU/OK button and the display will show “CONFIRM?”.

Press the MENU/OK to confirm,

or press the PHONEBOOK/CANCEL button to save the contacts.

Press the

MENU/OK button

, to see

“PHONE BOOK”.

Press the MENU/OK.

Press the DOWN button repeatedly until you see “EDIT RECORD”.

Press the MENU/OK button and the display will show the first name and number in your phonebook.

Scroll UP or DOWN until you see t he contact yo u want to edit .

Then press the MENU/OK button and a flashing bar will appear at the end of the name.

Use the keypad to enter characters or DELETE button to delete.

To delete all contacts in your phonebook

To edit a contact in your phonebook

Use the UP or DOWN buttons to scroll through the list

until you see the contact you want to delete.

Press the MENU/OK button and the display will show “CONFIRM?”.

Press the MENU/OK button to confirm if you really want to delete this

entry, or press the PHONEBOOK/CANCEL to save the contact.

In either case, the display will return to the previous menu option.

In either case, the display will return to the previous menu option.

Press the MENU/OK button to confirm, and the display will move the flashing bar to the end of the number position.

Use the keypad to enter digits or the DELETE button to delete.

Binatone Help Line : 0845 345 9677 15

Press the REDIAL/PAUS E button to review the last number redial list.

Scroll UP or DOWN to find the number you want to store.

Press the MENU/OK button. Then the display will show "ADD TO PB?".

Press the MENU/OK button to confirm, and the display will show a flashing

Key in the name for this redial number into the phonebook.

Press

the MENU/OK

button to confirm the name.

To store a last number redial in your phonebook

Once you have finished press MENU/OK button to confirm and the display will show “MELODY 1”.

Scroll UP or DOWN to select a melody..

Then press the MENU/OK button to confirm, and the

display will go back to the previous menu.

bar at the beginning of the name position.

The display will move the flashing bar to the end of the number position. If the number needs modifying use the keypad to enter digits or

Use the UP or DOWN buttons to scroll through the melodies.

Press the MENU/OK button to confirm your selection.

You will hear a confirmation tone, and the display will return to the last

the DELETE button to delete.

Press the MENU/OK button to confirm the number, and the display will show "MELODY 1".

number redial list.

Binatone Help Line : 0845 345 9677 16

Scroll UP or DOWN to select the name and number of the person you want to call.

Then pick up the handset or press the SPEAKERPHONE button to make the call.

This allows you to review how many records in the phonebook are occupied. The phonebook allows up to 150 names and numbers.

Press the

MENU/OK button, to

see

“PHONE BOOK”.

Press the

MENU/OK button, and then

Press the

MENU/OK.

Then the display will show the phonebook memory space available e.g. if you have saved 30 names and numbers in your phonebook, it would display 30/150.

Press the

PHONE BOOK/BACK

until you return to idle mode.

There are three Direct Memory buttons M1 and M2 and M3 on the corded base.

In idle mode, enter the telephone number you want to store.

Press and hold M1 key for more than 2 econds, until you hear the confirmation tone to indicate the number has been stored.

In idle mode, briefly press

and the unit will automatically dial out the

telephone number in speakerphone mode.

Making calls from the phonebook

Reviewing phonebook memory status

Direct Memory Call

To Store the telephone number

To Speed-Dial the telephone number

Either press the PHONEBOOK/CANCEL button once, or the MENU/OK button three times, and you will see the 1st number and name in the phonebook.

Note: For a short-cut to finding the name, you can press the digit buttons to go directly to the first entry beginning with the corresponding letters of that key, and then scroll from there.

press the UP or DOWN buttons until you see "MEM STATUS".

Binatone Help Line : 0845 345 9677 17

Caller Display (CDS) / Caller ID (CID)

To subscribe to this feature, you need to contact your service provider, and there may be a charge for this service . Caller Display lets you see the phone numbers of your callers on

the display, before you answer.

The base and each handset will store its own CID list independently. Both answered and unanswered calls are stored, up to a maximum of 20 calls. When the caller display list is full,

any new caller display entry will replace the oldest record.

If you receive a new call, the display will show the icon with the name and number of the caller.

If there are no items on the CID list, the display will show NO CALLS.

The display may al so show the f ollowing:

UNAVAILABLE – if the number of the caller is unavailable, e.g. from an international call. WITHHELD – if the call is from someone who has withheld their number, e.g. by dialling 141.

Press the MENU/OK button, to see PHONEBOOK

Press the DOWN button, to see "CALL LOG".

Press the MENU/OK button, to see “RECEIVED”.

Press the MENU/OK button, to see the most recent record in the CID list.

Press the UP or DOWN buttons to scroll through the CID list.

*If you wish to call directly from the CID list, press the SPEAKERPHONE button or lift up the handset to dial the number automatically.

New CID log

To review the CID list

To d record

The base and each handset will store its own CID list independently. Both answered and

unanswered calls are stored, up to a maximum of 20 calls. When the caller display list is

full, any new caller display entry will replace the oldest record.

The caller display information includes:

- the caller's number (up to 20 digits)

- the date and time of the call

- the caller's name (up to 12 characters) if the incoming number matches an entry

Note: it will also display the caller's name if the network sends it, but this is not normally

in the Phonebook

available in the UK.

The NEW

icon will

be displayed in the idle screen until all new calls have been viewed in the CID list.

Note: To go directly to the first record of the CID list,press the UP or DOWN buttons in standby mode.

Binatone Help Line : 0845 345 9677 18

Enter name using keypad.

Press

the MENU/OK

button to confirm the name.

The display will move the flashing bar to the end of the number position. If the number needs modifying use the keypad to enter digits or

Use the UP or DOWN buttons to scroll through the melodies.

Press the MENU/OK button to confirm your selection. You will hear a confirmation tone, and the display will return to the CID list.

Repeat the steps above to review the CID list, and to locate the record you want to store in the phonebook.

Press the MENU/OK button to see “ADD TO PB ?”.

Press the MENU/OK button to confirm, and the display will show a flashing bar at

To store a Caller ID contact in the phonebook

Repeat the steps above to review the CID list.

To delete all Caller ID records

Press the MENU/OK button, to see ADD to PB?

Press the DOWN button twice to see DELETE ALL?

Press the MENU/OK button twice, you will hear the completion tone and the display will show

EMPTY

the beginning of the name position

Press the MENU/OK button to confirm the number, and the

display will show "MELODY 1".

the DELETE button to delete.

Repeat the steps above to review the CID list, and to locate

To delete a Caller ID record

Press the MENU/OK button, to see ADD to PB?

Press the DOWN button, to see DELETE?

Press the MENU/OK button twice, you will hear the completion tone and the display will return to the Caller ID list.

the record you want to delete.

Binatone Help Line : 0845 345 9677 19

Ringer volume, melody

Press the

MENU/OK

button.

Scroll

DOWN

until

you see

“SETTINGS”.

Then press

the MENU/OK

button.

Scroll

DOWN

until you see

“RING SETUP”.

Press the

MENU/OK

button. Then it will display “

INT RING

” or scroll

DOWN

to select

“EXT RING”.

Press

the MENU/OK

button. The display will show

“MELODY”.

Scroll

DOWN

until

you see “VOLUME”.

Then press

the MENU/OK

button to select and the display will show

“VOLUME 2”.

Press the UP or DOWN button to scroll through the volume settings

(from OFF, 1 to 5).

Then press the

MENU/OK

button to confirm the setting

Press

the PHONEBOOK/BACK

button to return to the previous menu

There are 10 base ringer melodies from 1 to 10

Press the MENU/OK button.

Scroll

DOWN

until you see

“SETTINGS”.

To change ringer volume

To change ringer melody

You can adjust the volume level of the intercom ringer (INT RING) and the external call ringer (EXT RING) independently, with settings from 1 (quietest) to 5 (loudest), or turned OFF.

Binatone Help Line : 0845 345 9677 20

Press the UP or DOWN button to scroll through the Melody list (from 1 to 10).

Then press the MENU/OK button to confirm the setting.

Press the PHONEBOOK/CANCEL button to return to the previous menu.

Then press the MENU/OK button.

Scroll DOWN until yiu see “RING SETUP”.

Press the MENU/OK button. Then it will display “INT RING” or scroll DOWN to select “EXT RING”.

Press the MENU/OK button. The display will show “MELODY”.

Then press the MENU/OK button to select and the display will show

“MELOD Y 1”.

Binatone Help Line : 0845 345 9677 21

Using a multi-handset system

Receiving an intercom call from a cordless handset.

When the phon e rings and the display shows "HS 1 CALLING", you can answer the call by pressing the SPEAKERPHONE button or picking up the handset.

If you want to end the intercom, press the SPEAKERPHONE button or replace the handset.

During a call, it is possibl e to transfer a call to another handset.

To Make Intercom calls

To Transfer intercom call

Press the INTERCOM button. If you have only one cordless handset registered to the base, the display will show "CALLING HS1" and the base will beep.

If you have more than one handset registered to the base, the display will show "HS?" with the registered handset numbers above, and the base will output a continuous beep, until you press the number for the handset you want to intercom. Then the display will change, for example, to "CALLING HS2", if it is handset 2 that is being called. 

If you enter a number that is not available the base will return to idle mode.

The handset being called will ring with its selected melody and display

"BASE CALLING".

If you do not enter any number for 1 minute the handset will return to idle mode.

To cancel the intercom call press the INTERCOM button again.

During an external call, if you want to transfer the call to a cordless handset,

press the INTERCOM button. The external call will be put on hold.

If the base has only one cordless handset registered it will immediately start calling that handset, but if more than one handset is registered enter the number for the handset you want to transfer the call to.

When the handset answers the intercom call, simply hang-up at the base to  transfer the call.

[1][2]…

Binatone Help Line : 0845 345 9677 22

During an external call it is possible to conference in another handset.

During a call, press INTERCOM button and enter the number of the handset you want to connect to, by using the keypad.

The display will show the handset name you have entered and the other handset will ring. If the number you have entered is not available, you will hear an ERROR tone and the call will be returned to the original handset.

If you do not enter any number within 30seconds the call will also be returned to the original handset.

Receiving a conference call.

Either handset can just hang-up to end the call and the other handset will still be connected.

To Set up a three-way conference

If the handset does not answer within 30 seconds, the transfer will be cancelled and

Receiving a transfer call from a cordless handset.

When you have an intercom call transfer your handset will ring and the display will show

“HS 1 CALLING”

To answer the call, pick up the handset and you will be connected. If you want to end the intercom transfer, ha ng-up the phon e.

the external call reconnected to the base.

Once the other handset answers the call, press STAR( ) button and the display will change from "INTERCOM" to "CONFERENCE", and both the base and the

cordless handset will be connected to the external call.

When you receive intercom ringing from a handset, answer the call and the display will show "INTERCOM".

Then wait for the other handset to initiate the three-way conference call.

When either the base or the handset hangs up, the other will still be connected to the external call.

Alternatively, once the intercom ringing starts and the display shows, for example, "CALLING HS1", you can hang-up the phone to transfer the call automatically. The display will change to "TRANSFER HS1". The called handset will ring for 1

minute, but if it does not answer, both the base and handset will ring for another minute.If neither answers, the ringing will stop and the external call will be released.

Page / locate a handest

Press the INTERCOM button. If you have only one cordless handset registered

to the base, the display will show "CALLING HS1" and the base will beep.

If you have more than one handset registered to the base, the display will show "HS?" with the registered handset numbers above, and the base will output a continuous beep, until you press the number for the handset you want to page. Then the display will change, for example, to "CALLING HS2", if it is handset 2 that is being paged. 

If you enter a number that is not available the base will return to idle mode.

If you do not enter any number for 1 minute the handset will return to idle mode.

Handset registration

To register new handsets to the base:

The handset(s) supplied with your CC2310 system are already registered

— the first one as handset number 1, the second as number 2...etc

You don’t need to re-register them, unless you have a problem.

To check whether a handset is registered, make sure mains power to the base

unit is switched on and the handset is within range. The handset’s display

should show its number, and the ‘signal level’ symbol on the display should

show three bars. If the display shows "UNREGISTERED" , you need to re-register

the handset using the following process:

You need to operate the base and handset together:

1. On the handset, press the MENU/OK button to see "PHONEBOOK".

2. Press the UP button twice to see "REGISTRATION".

3. Press the MENU/OK button to see "BASE 1".

If the handset already has a registration to a base there is a "+" on the right side of the display, and you should choose another base number if you don't want to lose that one.

Binatone Help Line : 0845 345 9677 23

4. Press the DOWN

the MENU/OK button to see "PIN ?"

5. Press

Key in the 4 digit PIN code for the base - the CC2300 default PIN code is 0000

6. Press the MENU/OK button to confirm, and the "SEARCHING 1" (or 2,3,4)

7. At the same time, on the base, press

"PHONEBOOK"

8. Press the UP

9. Press the MENU/OK button to see

After a short delay, if the registration is successful, there will be a

confirmation beep, and the Handset display will go back to idle mode with number shown (e.g. HS1, HS2). The base display will also go back to

the new handset up a three-way conference

idle mode.

button to select a base number (BASE 1, 2,3 or 4)

display will flash

the MENU/OK button to see

button tweice to see

"REGISTRATION"

"SEARCHING" flash on base display

To de-register a handset

You may need to do this if you need to replace a faulty handset. Call the Binatone help

line if you need more advice.

To de-register a handset using the CC2300 base menu

With the base in idle mode:

1. Press the MENU/OK button to see 2 .Press the DOWN button twice to see

3. Press the MENU/OK button to see

4. Press the MENU/OK button to see

Press UP or DOWN button to select the handset you want to de-register.

5. Press the MENU/OK button to confirm, and the selected handset will be

de-registered. (The display on the handset that has been deleted will show "UNREGISTERED".)

Press the PHONEBOOK/BACK button to return to the previous menu

at any time.

Note: Handsets can also be de-registered using another cordless handset, as described in the cordless handset user guide.

"PHONEBOOK"

"SETTINGS" "DELETE HS" " HS 1 " (or 2,3, 4)

Binatone Help Line : 0845 345 9677 24

Binatone Help Line : 0845 345 9677 25

SOS call function

The SOS call function is very usef ul for people at home to make an emergency call to ask for help from their relatives, police, doctor, etc.

x Press and hold SOS button for more than 2 seconds.

x

The line is automatically seized and dials to each of the pre-stored SOS numbers, will wait for 1 minute and then drop the call.

x

Then it makes another call to the second SOS number, if programmed, and sends the lannouncement to ine for another 1 min.

x

Finally it will make another call to the third SOS number, if programmed,

x

When the SOS call function is active, you can only terminate this function by lifting up the corded handset on the base. It can not be terminated by using any buttons

on the cordless handset.

User is allowed to set up to 3 SOS numbers and 1 SOS voice recording.

Press the MENU/OK/MUTE. Scroll DOWN until you see “SOS SETTINGS”.

Press the

MENU/OK/MUTE

and you will see

“SOS NUMBER”

Press the MENU/OK/MUTE and you will see “SOS NUMBER 1”.

Scroll UP or DOWN to select SOS NUMBER 1 to 3.

Then press the MENU/OK/MUTE to select the one you want to program.

Enter the phone number.

Then press the MENU/OK/MUTE. You will hear a beep and the number is saved.

If you want to save more SOS numbers, press the DOWN to select the next location you want to program,and repeat above steps.

Press the PHONE BOOK/BACK until you return to idle mode

How SOS call function works

How to terminate SOS call function

To Set SOS numbers

The line is automatically seized and dials to each of the pre-stored SOS numbers, starting with the first. and it will wait for 1 minute and then drop the call.

and send the announcement to line for another 1 minute.

Binatone Help Line : 0845 345 9677 26

Advanced use of your phone

Press the MENU/OK. Scroll DOWN until you see “SETTINGS”.

Press the MENU/OK and then you will see “DELETE HS”.

Then scroll DOWN until you see “KEY TONE”.

Press the MENU/OK and the display will show “ON”.

Press the UP or DOWN button to select ON or OFF on the display.

Press the MENU/OK

button to confirm the option, and you will hear the confirmation beeps. The display will return to "KEY TONE".

Press the PHONE BOOK/BACK until you return to idle mode.

Press the

MENU/OK.

Scroll

DOWN

until you see

“SETTINGS”.

Press the MENU/OK and then you will see “DELETE HS”.

Scroll DOWN until you see “FLASH TIME”.

Press the MENU/OK and the display will show the current setting of

the Flash time, e.g. "100" ms.

Press the PHONE BOOK/BACK

until you return to idle mode.

To Turn on/off key tone

To Set Flash (Recall) time

The Recall (also called Flash) may be needed if you use BT calling functions or are connected to a PABX.

The default setting of this CC2300 telephone is 100ms, and normally this will be correct for the UK.

However, if necessary, you can select from 3 flash times: 100ms, 250ms and 600ms to meet your telephone line or PABX requirement.

Press the UP or DOWN button to show the flash time you want on the display.

Press the MENU/OK button to confirm the option, and you will hear the confirmation beeps. The display will return to "FLASH TIME".

Binatone Help Line : 0845 345 9677 27

Press the

MENU/O

K scroll DOWN until you see SETTINGS.

Press the MENU/OK then scroll DOWN until you see “BS DEFAULT”.

Press the MENU/OK and the display will show “PIN ?”.

Enter the PIN code using the keypad. (Default PIN is 0000)

Press the MENU/OK and you will hear the confirmation beeps and the display will return to idle mode.

To Set Base to default settings

Press the MENU/OK . Scroll DOWN until you see “SETTINGS”.

Press the MENU/OK and then you will see “DELETE HS”.

Scroll DOWN until you see “DIAL MODE”. Press the MENU/OK and the display will show the current setting of Dialli ng Mode e.g. “TONE” or

“PULSE”.

Press the PHONE BOOK/BACK until you return to idle mode.

To Set Dialling Mode (Tone/Pulse)

However, for some old telephone lines or PABX systems you may need to change

the dialling mode from Tone to Pulse.

Press the UP or DOWN button to show the dialling mode you want on the display.

Press the MENU/OK button to confirm the option, and you will hear the  confirmation beeps. The display will return to "DIAL MODE" .

This allows you to restore base settings to their default settings:

Ext Ringer Volume = 5

Ext Ringer Melody = 1

Int Ringer Volume = 5

Int Ringer Melody = 2

Dial Mode = TONE

Flash Time = 100ms

Key Tone = ON

Language = ENGLISH

PIN CODE = 0000

The Caller Display (CID) and Redial lists will be erased, but the Phonebook memories  and TAM settings will remain unchanged.

The default setting of this CC2300 telephone is TONE (also called Touch Tone, MF or DTMF),

and normally this will be correct for the UK, so will not need to be changed.

Binatone Help Line : 0845 345 9677 28

Some functions (including handset registration) require a PIN code. The default PIN is 0000 but you are able to change to your personal 4-digit PIN.

Press the MENU/OK button.

Then scroll

DOWN until you see “SETTINGS”.

Then press the MENU/OK button.

Then scroll DOWN until you see “MODIFY PIN”.

Press the MENU/OK button and the display will show

“PIN ?”.

Enter the PIN code using the keypad (if you haven’t changed it, the default PIN is 0000).

Press the MENU/OK button and the display will show

“NEW PIN”.

Use the keypad to enter the new PIN (4 digits from 0-9).

Press the MENU/OK button to confirm a nd the display will show

“REPEAT”.

Use the keypad to enter the new PIN again and

press the MENU/OK button to confirm.

Press the PHONE BOOK/BACK until you return to idle mode.

* If you enter the wrong PIN at any time you will hear an error tone and the display will return

to the previous menu.

To Change the PIN code

You will hear the confirmation beeps and the display will return to "MODIFY PIN".

Binatone Help Line : 0845 345 9677 29

Troubleshooting

ALWAYS check first that:

x

You have followed all the steps listed onpages 5 & 6 to install and set up your CC2300

x All

connectors

are firmly inserted in their sockets

x Mains power to the base unit is switched on at the socket

x

The handset’s batteries are correctly and securely installed and are not run down

Everyday use

“I cannot make or answer calls ”

x Check that the base unit’s

mains power adapter

is plugged

in and power is switched on. The base unit needs mains power for norm al operati on of the phon e – only the basic

handset calling works without mains power.

x

Make sure you are using the telephone line cable supplied with your CC2300. Other telephone line cables might not work.

x

Switch off power at the mains socket, wait for a few seconds and then switch back on. This may solve the problem.

“I cannot make a call”

x

Only one handset (or the base unit) can be connected to the outside line at once. If a cordless handset is already using the line, you need to wait until it’s finished its call.

“The phone does not ring”

x

Check that the base unit’s mains power adapter i s plugged in and power is switched on. The base unit needs mains power for norm al operation of the phon e – only the basic handset calling works without mains power.

x

Make sure you are using the telephone line cable that was supplied with your CC2300. Other telephone line cables might no t work

Binatone Help Line : 0845 345 9677 30

x

You need to subscribe to the Caller Display feature from your network service provider. You should find contact details on your phone bill.

“The Caller Display feature isn’t working”

x

The caller may have withheld their number by dialling 141. Or they may be calling from a network that does not transmit the caller’s number (e.g. it may be an international call.)

“When I try to make a call, I hear Busy tone.”

x

If you’re using a CC2300 multi-handset system, check whether other handsets are already on a call.

x

Make sure you’ re holding the earpiece correctly over your ear.

“The volume in the earpiece is low when I’m on a call”

x Adjust the volume using the UP/DOW N button.

Intercom and transfer

x

Make sure the other handset is in range of the base unit.

“I can’t transfer a call”

x Make sure you a re dialling the correct n umber for the other

handset.

If the fault persists…

x

Disconnect all other instruments

connected to the same

line as the CC2300 and try to make a call

x

Disconnect the base unit from the telephone line and plu g a different phone into the master telephone socket. Try making a call. If this works, the line is OK.

x

If the call does not work, and you are using a two-way socket adapter, remove it and plug a telephone directly into

the socket. I f the call no w works, the adapter may be faulty.

x If you cannot make a call, the fault may be on the exchange

line. Contact the service provider (the BT engineers on 151

for UK only, or your cable company).

x

If you still cannot identify the cause of the problem, contact the Binatone on 0845 345 9 677 (UK only).

Binatone Help Line : 0845 345 9677 31

Cleaning and care

Do not clean any part of your CC2300 with benzene, thinners or other

solvent chemicals – this may cause permanent damage which is not covered by the Guarantee. When necessary, clean it with a damp cloth.

Keep your CC2300 away from hot, humid conditions or strong sunlight,

and don’t let it get wet.

Every effort has been made to ensure high standards of reliability for your

CC2300. However, if something does go wrong, please do not try to repair it yourself – consult your supplier or the Binatone Helpline.

Declaration of conformity

The cordless phone, identified as CC2300, complies with the essential protective requirements and objectives of:

EC R&TTE Directive 1999/5/EC EC Low Voltage Directive 2006/95/EC EC EMC Directive 89/336/EEC

And conforms to the following relevant harmonized standards:

Radio: EN 301406 (TBR 6) EMC: EN 301489 Safety: EN 60950

The conformity to the requirements is validated by the

symbol.

NOTE: In compliance with Directive 2002/96/EC, when you purchase a product that comes with the symbol shown on the right, you are required to dispose the electrical and electronic equipment by separate waste collection and you cannot dispose of the product as normal waste. This equipment and all its components, subsystems and consumable m aterials form an integral part of this prod uct and when you decide to dispose them, you have to bring them to the local recycling centr es for appropri ate waste dis posal, in compliance with the current regulations. Details about the location of these centres can

be obtained from your local authority.

Binatone Help Line : 0845 345 9677 32

Guarantee and service

The CC2300 is guaranteed for 12 months from the date of purchase shown on your sales receipt. This guarantee does not cover any faults or defects caused by accidents,

misuse, fair wear and tear, neglect, faults on the telephone line, lightning, tampering with

Please keep your sales (till) receipt – this is your guarantee. You should also keep the original packaging material.

In the unlikely event that you need to return your CC2300 to our Repair Centre while it is under guarantee, there will be a £5 handling charge.

While the unit is under Guarantee

1. Disconnect the base unit from the telephone line and the mains electricity supply

2. Pack up all parts of your CC2300, using the original packaging. Remember to

include the m ains adapter

3. Return the unit to the shop where you b ought it, mak ing sure you take your sales receipt.

After the Guarantee has expired

If the unit is no longer under Guarantee, first follow steps 1 and 2 as for repair under Guarantee.

Then…

3. Call Binatone Helpline on 0845 345 9677 (for UK onl y) and ask f or a quotation of the repair charge and details of where to send your CC2300 for repair.

4. Make sure you include with your CC2300:



Your name and address

A cheque or postal order for the value of the repair charge

5. Return your CC2300 to the address given by the Service Department.

* This does not affect your s tatutory rights.

the equipment, or any attempt at adjustment or repair other than through approved agents.

Binatone Help Line : 0845 345 9677 33

Technical details

Standard Cordless Telecommunication

Frequency range 1.88 to 1.9 GHz (bandwidth = 20 MHz)

Channel bandwidth 1.728 MHz

Operating range Up to 300m outdoors; up to 50m indoors

Operating time Standby: 150 hours

Talking: 9 hours Battery charge time: 24 hours

Temperature range Operating 0 ºC to 40 ºC Storage -20 ºC to 60 ºC

Electrical power

HANDSET – two pcs of AAA-size 550mAH NiMH 1.2V rechargea ble batteries Base UNIT – input 230VAC 50Hz; output 7.5VDC – 500mA CHARGER POD – input 230VAC 50Hz; output 6VDC – 200mA

Port specification The port (connect to the mains power supply) is a SELV port with respect to EN41003.

The port (connected to the telephone line) is a TNV port with respect to

EN41003.

PBX compatibility:

Timed break recall (flash): adjustable to 100ms (default), 250ms or 600ms Pause length: 3 seconds Dialling type: Tone (DTMF, dual tone multi-frequency) or Pulse (loop disconnect).

Network connection: This equipment is intended to be used in the UK only. Operation on other countries' PSTN termination points cannot be guaranteed.

Binatone Telecom plc operates a policy of continuous improvement, and so reserves the right to make changes to the products and functions without notice.

Binatone Concept Combo 2300 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual