Binatone Action 1000 User Manual
USER GUIDE
Private mobile radio with twin charger
1. LCD Screen
1. Antenna
4. LCD Screen
Displays the current channel
selection and other radio symbols.
8. PTT (PUSH to TALK) button
Press and hold to transmit.
9. CALL button
10. UP/DOWN
11. Speaker
Buttons
Press to change channels, volume,
and to select settings during
prog
ramming.
Channel Number. Changes from 1 to
8 as selected by the user.
Digital Code. Changes from 1 to 83
as selected by the user.
TX Displayed when transmitting a signal.
RX Displayed when receiving a signal.
DCS Displayed when the Digital Code System is turned On.
VOX Displayed when the VOX feature is enabled.
Action 1000
CTCSS Code. Changes from 1 to 38
as selected by the user.
Displayed when the Dual Watch function is turned ON.
DCM
CTCSS
5. Transmit (LED)
01
Helpline No. UK/Northern Ireland
Web Support
http://www.binatoneonline.com/
08453459677
0818762092
1
2
8
7
9
10
11
3
4
5
6
**Please note that all calls are charged at local rate
www.binatonetelecom.com
Binatone Helpline
Monday to Friday
from 9:00am to 5:00pm
Tel: 0845 345 9677
or visit our website:
(for UK only)
3. Headset/Charge jack
6. MENU Button
Press to switch between Modes.
7. MIC(Microphone)
Press to send Call-ring tone
to other PMR units.
Displays the Battery charge level.
When the bars are gone, the
batteries need recharging.
Displayed when the CTCSS sub-channel is turned On.
2. POWER
/VOL Switch
Rotate clockwise/counter clockwise
to turn the unit ON or OFF.
SCAN Displayed when the PMR is scanning all channels.
Displayed when the Key Lock feature is activated.
Displayed when the call signal is ON.
Displayed when the vibrator function is activated.
02
Helpline No. UK/Northern Ireland
Web Support
http://www.binatoneonline.com/
08453459677
0818762092
2. Installation
2.1 Removing the Belt Clip
2.2 Installing the Belt Clip
Belt Clip latch
Figure 1 Figure 2
a. Slide the Belt Clip into the
slot as shown in Figure2.
A “click” indicates the Belt
Clip is locked into position.
Figure 3 Figure 4
Important
a. Insert the small plug on the end of the mains adaptor into the
Power-in Connection Jack at the back of the desktop charger.
b. Plug the mains adaptor into a 240V AC, 50Hz main socket with
the switch on the socket set to OFF.
c. Switch ON the mains socket.
The Action1000 must be charged using the mains adaptor provided.
Using any other adaptor will result in non-compliance with
EN60950-1 and will in
validate any approvals & warranty.
2.3 Installing the Batteries
b. Insert the 4 “AAA” size rechargeable batteries by following the
c. Replace the Battery Compartment Cover. See Figure 4.
Binatone Help Line - 0845 345 9677
a.Pull the Belt Clip latch up
(away from the Action 1000)
Caution: Observe the
correct
battery orientation when installing
the
batteries. Incorrect
installation
can damage both the
batteries and the unit.
a. Remove the belt clip, unclip the latch at the bottom and remove
the cover.
Read these Safety Warnings before you charge the batteries.
When placing the Action1000 in the charger, use only the power
suppy supplied with the Action 1000.
Don’t try to recharge non-rechargeable batteries.
Make sure the battery compartment cover is securely
locked in
place when you are charging the batteries.
Dispose of used batteries safely and in a way that will not harm
the environment- never try to burn them or put them anywhere they
could get burnt or punctured.
Don’t leave dead batteries in your Action 1000 units. They might
leak if you do.
+ /- polarity markings inside the Battery Compartment as shown
in Figure 3.
2.4 Charging the Batteries
b. While pulling the Belt Clip
latch, slide the Belt Clip up as
shown in Figure1.
03
Helpline No. UK/Northern Ireland
Web Support
http://www.binatoneonline.com/
08453459677
0818762092
d. Place the Action 1000 units in the charge cradle in an upright position.
The Charge LED indicators will light up.
completely run down. New batteries take up to 14 hours to fully
charge.
Important:
Always turn off the PMR units
when charging. This will
shorten the charging time.
Mains socket
Then switch ON the mains socket.
The Action 1000 can detect the battery charge in 4 levels;
Battery charge at high level.
Battery charge at medium level.
Battery charge at low level. At this level, the Action 1000 will
Important: Charge the unit for 10-14 hours.
Binatone Help Line - 0845 345 9677
e. It takes about 10 hours to fully charge the batteries if they are
Charge jack
Headset jack
Plug the mains adaptor into a
240V AC, 50Hz main
socket with the switch on the
socket set
to OFF.
Use only
the power supply
supplied with the Action 1000.
CAUTION : Risk of explosion if the battery is replaced
by an incorrect type. Dispose of used batteries according
to the instructions.
The Action 1000 has a built in power save function to make the
batteries last longer. But when you are not using the units,
turn them OFF to conserve battery power.
Insert the round connector of
the 9.0V DC/300mA adaptor
into the charge jack.
c
ll
a
OR: Charging the batteries directly (using the adaptor)
Lift the charge socket cover located on the right
side of the handset.
The battery meter is located in the left lower corner of the LCD
Screen. It looks like a battery with three bars inside. These indicat
the amount of power available. When the battery level reaches its
minimum level in PMR on mode, the unit will emit two beep tone
and automatically power off.
emit a “beep” sound every 10 seconds in normal mode.
Important: Charge the unit
for 10-14 hours.
Battery charge at very low level. When the battery
level reaches its minimum level
during
on mode, the unit
will
emit two "beep's" and automatically turn off the
power.
Loading...