Binatone 2310 User Manual

USER GUIDE

Before operating this set,

please read these instructions carefully.

Concept Combo 2310

CORDED AND
DIGITAL CORDLESS
TELEPHONE WITH

ANSWERING MACHINE

UK BTP Ver 4, Nov 07

Note: This guide is for the corded part only. For instructions on how to use
the cordless part see the "Combo 2310 Cordless Handset" user guide.

Important note — emergency calls

The CC2310 cordless handset is not designed for
making emergency calls when the mains power fails.
But, if there’s a power failure, you can use the base
unit telephone to make an Emergency Call, by lifting
up the corded handset instead of using the
speakerphone.

*** Before operating this set, please read these
instructions carefully.

If you need help …..

Binatone Helpline (for UK only)

Monday to Friday from 9:00am to 5:00pm

Tel: [phone]

**Please note that all calls are charged at local rate
Or visit our website:

http://www.binatoneonline.com

Unpacking your CC2310 system

In the box, you will find:

Ƶ the base unit telephone
Ƶ a telephone line cable for the base unit
Ƶ a

mains power adapter

for the base unit

Ƶ the cordless handset (up to five, depending on
which CC2310 system you’ve bought)

Ƶ

two 1.2V 550mA rechargeable batteries and a

battery compartment cover for each handset

Ƶ up to five charger pods, each with a mains power
supply for multi handset systems

Ƶ two user guides, one for the corded phone and one
for the cordless handset.

Keep the packaging materials in a safe place in case
you later need to transport the unit.

Keep your sales (till) receipt, which is your
guarantee.

Note: After lifting the handset you will need to wait
for several seconds to get dial tone, before keying in
the telephone number to make the call.
Also you cannot dial numbers from memories when

the mains power is off.

Binatone Help Line : 0845 345 9677 1

LCD Display

Menu/Ok /Mute /OK

Press to access menu
Press as “OK” key to

confirm your operation

Press to mute/un-mute

microphone during a call

Phonebook/Back

/C

Press to access phonebook
records
Press to exit present menu

R(Recall)

You may need this function

if your phone is connected

to a PBX, or if you use BT

Stop/Answer on/off

Press to stop recording
or playback.

Press & hold to switch
the answering machine
ON or OFF.

With TAM ON in standby
mode, press to select
OGM1 & OGM2

Message Light

Turns ON when the TAM
is ON.
Flashes when you have
new TAM messages.

SOS Call

Press and hold for 5 seconds
to activate the SOS call

Speakerphone

Press to call or answer a call
by using the speakerphone.

Microphone

For speakerphone

and answering

Where to find it

Important:

When the instruction simply say ‘press’ a button, this means you should press it briefly then

release it.
When the instruction say ‘press and hold’ a button, this means you should keep i t pressed

until the display changes or you hear a tone.

Pres

messages, memos,

stored numbers or

Call

Delete (DEL)

s to delete

er Display records.

Memo/Ski p

Press and hold to

record a memo
Press during message
playback to go forward
to next message

Play/Pause

Press to playback
messages memos
Press to pause playing
of a memo or message

OGM/Rewind

Press and hold to record
OGM
Press to playback OGM
Press to go back to
previous message/s.

Intercom

Press to make an intercom
call or to transfer a call

Up-Down(CDS)

Press to access the
Caller display records
and scroll through them
Press to change earpiece
speakerphone volume

Press to scroll through the lists
the lists and menu options

RD/P

Press to redial the
last number

Press while dialing a
number to insert a pause

Calling Features.

machine recording.

Binatone Help Line : 0845 345 9677 2

What's on the display?

What do the symbols mean?

Talk

x

This will display when the user picks up the
handset

Ring Off

x

This will display when the ringer is set to
OFF

Phonebook

x This will display when you are in the

phonebook menu

Voicemail

x

Repeat CID

x This will display when the same caller has

called more than once

New CID

x

This will display when there is a new CID
entry or if one is being viewed

Sequence

x Indicates the sequence number of the CID

record

Hands free/speakerphone

x

This will display when the speakerphone is
in use

A.M.

x This will display if it is A.M., in the 12 hour

clock mode

P.M.

x

This is display if it is P.M., in the 12 hour

clock mode

Number field: shows the telephone
numbers

Character field: shows the Menu,
name and status of a call

The display of your telephone contains one line with the Time/Date and Icons, one line
of numbers and one line of text.

This will display when you have a new Voice
Mail message. (This is a caller id service and
is not usually available from UK network
providers.)

Binatone Help Line : 0845 345 9677 3

Contents

Page

Where to find it 1

What’s on the display? 2

x What the symbols mean? 2

Read First before Use 5

x

Choosing a site for base unit and
charger pod 5

x

Mains power connection 5

x If you have a broadband line 5

Installation and Set-up

x

Choose a suitable site for the base unit
6

x

Connect the mains power lead and the
telephone line cord into the base unit 6

x Plug the mains adaptor into your wall

socket 6

x

Connect the base unit to the telephone
line 6

Desk/Wall mount installation 7

Desk Mount 7
Wall Mount 7

Basic settings

x To set Date and Time 9

Making and answering calls 10

x

To make call

x

To make a call from redial list 10

x To make a call from caller display (CID)

list 10

x

To answer a call 10

x

To Mute or un-mute the microphone 11

x

To change the earpiece or speakerphone
volume during a call 11

x

Emergency call without mains power 11

Memory/Phonebook management 12

x

To create a contact in your phonebook

Page

x

To delete a contact in the phonebook 13

x

To delete all contacts in your phonebook
14

x

To edit a contact in your phonebook 14

x

To store a last number redial in your
phonebook

x

Making calls from the phonebook

x

Reviewing phonebook memory status

x

New CID log 17

x

To review the CID li

x To delete a Caller ID record 18

st 17

x

To delete all Caller ID records 18

x

To Store a Cal ler ID contact in
phonebook 18

Ringer volume, and melody 19

x To change ringer volume 19
x

To change ringer melody 19

Using multi-handset 21

x

To make intercom calls 21

x To Transfer intercom call 21
x

To set up a three-way conference 22

Telephone Answering Machine (TAM) Setup

25

x

Switching TAM on/off 25

x To Record your Outgoing Message

(OGM)

27

x

To playback the OGM 28

x

To delete the OGM (SET OGM to
DEFAULT) 29

6

9

10

15

16
16

x

Switch between OGMs 29

x

To setting ring number 30

x

13

x
x

Caller Display (CDS)/Caller ID (CID) 17

Page / locate a handest 23

Handset registration 23

To Set TAM alarm 30

Binatone Help Line : 0845 345 9677 4

x

31

x

31

x

31

x

32

x

32

x

32

x

33

x

34

SOS call function 35

x

How SOS call function works 35

x

How to terminate SOS call function 35

x

To Set SOS numbers 35

x

To Record SOS voice prompt 36

x

To Playback the SOS voice prompt 36

Advanced use of your Phone 37

x

To Turn key tones on/off 37

x

To Set flash (Recall) time 37

x

To Set Dialling Mode (Tone/Pulse) 38

x

To Set Base to default settings 38

x

To Change the PIN code 39

Troubleshooting 40

Cleaning and Care 42

Declaration of Conformity 42

Guarantee and Service 43

Technical Details 44

Connection and conditions for use.

You can connect your Concept Combo 2310 to a direct exchange line (DEL) - a line
connected to a local exchange, with its own phone number; to an extension on an approved
compatible PBX. Do not connect the Concept Combo 2310 as an extension to a payphone.

The ringer equivalence numbers (RENs) of all instruments (phones, fax machines, etc.)
connected to an exchange line must not add up to more than 4 - otherwise, one or more
of them may not ring and/or answer calls correctly. The Concept Combo 2310 has a
REN of 1, and most other telephones have a REN of 1 unless marked otherwise.

Incoming Call Messages (ICM)

Remote Operation

To record a memo on TAM

To play/pause messages on TAM
To delete a message in TAM

To delete all messages on TAM
To Change Security Code (TAM PIN)

To Reset TAM to default settings

Binatone Help Line : 0845 345 9677 5

Read First Before Use

Choosing a site for the base unit and charger pod

The base unit and charger pod(s) should be placed on a level surface, in a position where:

x

the mains adapter plug will reach an easily accessible 230-VAC switched mains
supply socket - never try to lengthen the mains power cable

x

the base unit's telephone line cable will reach your telephone line socket or
extension socket

x

it is not close to a sink, bath or shower, or anywhere else where it might get wet

x it is not close to other electrical equipment - fridges, washing machines,

microwave ovens, fluorescent lights, televisions etc.

x

if the base comes into contact with liquids, disconnect it promptly and use a soft
cloth to dry it; if you believe that the liquid has seeped into the unit, do not
reconnect the base station. Contact the Binatone helpline.

x

it is away from hot, humid conditions and strong sunlight

Mains power connection

IMPORTANT - The CC2310 base unit must be used with the mains adapter supplied
with the unit.

Using any other adapter will result in non-compliance with EN60950, and will
invalidate any approval given to this apparatus.

If you have a Broadband line

If you connect your telephone to a line with a broadband connection, you will need to
insert a micro-filter between the telephone and the telephone line; otherwise you may
get interference between the telephone and the broadband, which could cause
problems.

In a home with broadband, every telephone must have a micro-filter connected, not
just the one at the telephone point that your modem is connected to. If you need more
broadband micro-filters, contact your broadband supplier.

Binatone Help Line : 0845 345 9677 6

Installation and Set-up

1/ Choose a suitable site for the
base unit (see page 5)

2/ Connect the mains power lead
and the telephone line cord into the
base unit

Plug one end of the telephone line
cord into the jack on the back of the
base (the other end will plug into the

3/ Plug the mains adaptor into your wall
socket. If you have one or more charger pods,
plug the mains adaptors accordingly

Make sure that the 230VAC, 50hz mains socket is switched OFF
when you plug the mains adapter into the socket.

4/ Connect the base unit to the telephone line

Insert the telephone line plug into the socket then

See the note
on page 5

See the note
on page 5

switch mains power back ON.

Make sure the mains socket is switched on

—

the phone won’t work without electrical power

telephone wall socket later)

Binatone Help Line : 0845 345 9677 7

Desk/Wall mount installation

To place the CC2310 on a desk, connect
the stand to the bottom of the phone in the
slots near the rear of the base as shown below.

Desk Mount

Insert the rigid clips of the stand into the slots
on the bottom of the phone (nearer the centre

of the base ). Press down firmly until the
flexible clips clicks into place.

To remove the stand, (1) pinch the flexible
clips, (2) pull back the stand, and then (3)
slide up and forward as shown below.

To place the CC2310 on a wall, connect the
stand to the bottom of the phone in the slots
near the front of the base as shown below.

Wall Mount

Desk/Wall mounting continued...

Insert the rigid clips of the stand into the slots
on the bottom of the phone (nearer the centre
of the base). Press down firmly until the flexible
clips clicks into place.

To remove the stand, (1) pinch the flexible
clips, (2) pull back the stand, and then (3)
slide up and forward as shown below.

Mark two points on the wall that are 77 mm
apart to lay the fixing centers as shown below.

77 mm

BE CAREFUL to check that there are no
electrical wires hidden in the wall. Fix two screws
at the marked locations, leaving approximately
7mm between the wall and the the screw head.
Hang the telephone on the screws using the

wall mount slots. You may need to remove the

telephone from the wall and tighten the screws
so that the telephone is securely fixed and does

not wobble. Place the Handset on the cradle with

the parking hook on the cradle arranged to fit
in the parking recess under the earpiece on
the Handset.

Binatone Help Line : 0845 345 9677 8

Binatone Help Line : 0845 345 9677 9

Basic settings

Press the MENU/OK/MUTE button

Then press the UP or DOWN button until "SETTINGS" is displayed.

Then press the MENU/OK/MUTE to confirm.

The display wil l show “DELETE HS”,

Press the UP or DOWN button until "DATE & TIME" is displayed.

Then press the MENU/OK/MUTE to confirm.

The 'year' will be flashing.

Press the UP or DOWN button to set the year.

Press the MENU/OK/MUTE to confirm.

The 'month' will be flashing.





You will hear a beep and the display will show “DATE & TIME”.

Press the “PHONEBOOK” button to return to the previous menu.

To set Date and Time

Press the UP or DOWN button to set the month

Press the

MENU/OK/MUTE

to confirm.

The 'date' will be flashing.

Press the UP or DOWN button to set the date

Press the MENU/OK/MUTE to confirm.

The 'hour' will be flashing.
Press the UP or DOWN button to set the hour, including the AM/PM setting

Press the MENU/OK/MUTE to confirm.

The 'minutes' will be flashing.
Press the UP or DOWN button to set the minutes.

Press the MENU/OK/MUTE to confirm.

Press the "PHONEBOOK" button to return to the previous menu.

The format for the date is YYYY-MM-DD, and the time is HH:MM in 12 hour format

Note:If you subscribe to Caller Display (see page 17) your CC2310 time and date settings
will be automatically updated by the network when you receive an incoming call.

The Caller Display service only sends the month and date, not the year, so you may
still need to set the year, as this is used to calculate the day for the answering machine 
time stamp.

If the time and date are set on the cordless handset, it will automatically be set on
the base unit, and vice-versa.

or

or

or

or

or

or

or

Binatone Help Line : 0845 345 9677 10

Making and answering calls

a call

Pick up the handset and the TALK icon will appear, OR press the
SPEAKERPHONE button and the SPEAKERPHONE icon will appear.

Also the display will show “LINE IN USE”.

Use the keypad to enter the number you wish to dial.

When you have finished the call place the handset back on the base.

e a call from the redial list

The phone remembers the last 10 dialled numbers. The list is in order, with the

Press the REDIAL/PAUSE Button to view the redial list.

Press the UP or DOWN button until you see the number of the person you want to call.

Press the SPEAKERPHONE button or pick up the handset to make the call.

* To insert a pause in the dialling sequence, press the RD/P button, which will then show

a P in the number.

Press the UP or DOWN button to show the first entry in the CID list.

Press the UP or

DOWN button

until you see the number of the person you

want to call.

Press the

SPEAKERPHONE button

or pick up the handset to make the call.

When the phone rings:

Pick up the handset or press the SPEAKERPHONE button to answer the call.

or

or

To make a call

To make a call from the redial list

To make a call from Caller Display (CID) list

To answer a call

You can also make a call by using the Pre-Dialling function:
Dial the required telephone number first, and if you make a mistake you can
correct it by using the DEL button to delete digits and then add the right ones.
Pick up the handset or press the Speakerphone button.
The number will be dialled out automatically using the handset or
speakerphone mode selected.

most recent message at the top.

Binatone Help Line : 0845 345 9677 11

During a call press the MENU/OK/MUTE button and the display will show

“CALL MUTED”.

To un-mute, press the MENU/OK/MUTE button and the display will show

“LINE IN USE”.

During a call press the UP button to increase or DOWN button to decrease the
Volume.

The CC2310 corded base unit can make an emergency call with the corded handset
when the mains AC power is disconnected.

x

Pick up the corded handset.
After lifting the handset you will need to wait for several seconds to get dial tone,
before keying in the telephone number to make the call.

x

When the mains power is off, you can also answer an incoming call with the



When the phone rings, pick up the corded handset. After lifting the handset you

or

EMERGENCY CALL WITHOUT MAINS POWER

To change the earpiece or speakerphone volume during a call

To Mute or Un-mute the microphone

It is not possible to dial numbers from memories when the mains power is off.

will need to wait for several seconds before you can hear the calling person's voice



corded handset. 

or before they can hear you.

Binatone Help Line : 0845 345 9677 12

Memory/Phonebook management

How to enter characters?

Telephone Keypad characters

To enter the characters, press the button
where you see the character e.g. if you want to

insert the letter ‘A’ you press ‘2’ if you want to
insert the lett er ‘B’ you press twice and for ‘C’,
three times etc. If you want to insert ‘AA’ then
you will have to wait for the first ‘A’ to stop
flashing then insert the second ‘A’. Press

twice for space, to delete single characters

and press and hold to delete the whole text.

DEL

1st 2nd 3rd 4th 5th 6th

_ , ?

!

’

”

( ) : ; .

A B C 2

D E F 3

G H I 4

J K L 5

M N O 6

P Q R S 7

T U V 8

W X Y Z 9

space 0 + - @ = / \ [ ]

*

#

? !

1

7th 8th 9th 10th 11th 12th 13th 14th

á

~

ú

í

~

N

DEL

Æ

Ç

Binatone Help Line : 0845 345 9677 13

The Phonebook can store up to 150 names (maximum 12 characters) and numbers

Also, you can select a different ringer melody for each entry, but this will only work if

Press the MENU/OK/MUTE button, to see “PHONE BOOK”.

Press the MENU/OK/MUTE button, to see “LIST”.

Press the DOWN button, to see "NEW ENTRY".

Press the MENU/OK/MUTE button and the display will show a flashing bar
at the beginning of the name position.

Key in the name using the digit keys (maximum 12 characters). If you
make any mistakes press DELETE button to delete.

When you have finished press the MENU/OK/MUTE button to confirm, and

Key in the number using the digit keys (maximum 20 digits). If you make any

Press the MENU/OK/MUTE button to confirm and the display will show

“MELODY 1”.

Use the UP or DOWN button to scroll through the melodies. (there are 10
melodies to choose from).

Press theMENU/OK/MUTE button to confirm your selection. You will hear a

confirmation tone, and the display will return to “NEW ENTRY”.

*If there is no more space in the phonebook, “MEMORY FULL” will appear on the
display.

To create a contact in your phonebook

(maximum 20 digits) in the memory.

you subscribe to CID (see page 17).

the display will move the flashing bar to the beginning of the number position.

mistakes use the DELETE button to delete.

Press the MENU/OK/MUTE button, to see “PHONE BOOK”.

Press the MENU/OK/MUTE button, to see "LIST".

Press the DOWN button repeatedly until you see

“DEL RECORD”.

Press the MENU/OK/MUTE button. The display will show the first name and
number in your phonebook.

To delete a contact in your phonebook

or

Binatone Help Line : 0845 345 9677 14

Press the MENU/OK/MUTE button, to see “PHONE BOOK”.

Press the MENU/OK/MUTE button, to see "LIST".

Press the DOWN button repeatedly until you see "DELETE ALL".

Press the MENU/OK/MUTE button and the display will show "CONFIRM?".

Press the MENU/OK/MUTE to confirm,

PHONEBOOK/CANCEL

or press the button to save the contacts.

Press the

MENU/OK/MUTE button

, to see

“PHONE BOOK”.

Press the MENU/OK/MUTE button, to see "LIST".

Press the DOWN button repeatedly until you see “EDIT RECORD”.

Press theMENU/OK/MUTE button and the display will show the first

name and number in your phonebook.

Scroll UP or DOWN until you see t he contact you want to edit.

Then press the MENU/OK/MUTE button and a flashing bar will appear at

the end of the name.

Use the keypad to enter characters or

DELETE button to delete.

To delete all contacts in your phonebook

To edit a contact in your phonebook

In either case, the display will return to the previous menu option.

Press the MENU/OK/MUTE button to confirm, and the display will move the
flashing bar to the end of the number position.

Use the keypad to enter digits or the DELETE button to delete.

Use the UP or DOWN buttons to scroll through the list until you see the

Press the MENU/OK/MUTE button and the display will show “CONFIRM?”.

Press the MENU/OK/MUTE button to confirm

if you really want to delete this entry, or press the PHONEBOOK/CANCEL

to save the contact.

contact you want to delete.

In either case, the display will return to the previous menu option.

or

or

Binatone Help Line : 0845 345 9677 15

The display will move the flashing bar to the end of the number position.
If the number needs modifying use the keypad to enter digits or

Use the UP or DOWN buttons to scroll through the melodies.

Press the MENU/OK/MUTE button to confirm your selection.
You will hear a confirmation tone, and the display will return to the last

the DELETE button to delete.

Press the MENU/OK/MUTE button to confirm the number, and
the display will show "MELODY 1".

number redial list.

Press the

MENU/OK/MUTE

button to confirm the name.

Key in the name for this redial number into the phonebook.

Once you have finished press the MENU/OK/MUTE button

to confirm and the

display will show “MELODY 1”.

Scroll UP or DOWN to select melody.

Then press the MENU/OK/MUTE button to confirm, and the
display will go back to the previous menu.

or

Press the REDIAL/PAUSE button to review the last number redial list.

Scroll UP or DOWN to find the number you want to store.

Press the MENU/OK/MUTE button. Then the display will show “ADD TO PB?”.

Press the MENU/OK/MUTE button to confirm, and the display will show a flashing

To store a last number redial in your phonebook

bar at the beginning of the name position.

or

or

Binatone Help Line : 0845 345 9677 16

Either press the PHONEBOOK/CANCEL button once, or the MENU/OK/MUTE
button three times, and you will see the 1st number and name in the phonebook.

Scroll UP or DOWN to select the name and number of the person
you want to call.

Then pick up the handset or press the SPEAKERPHONE button to make

This allows you to review how many records in the phonebook are occupied. The
phonebook allows up to 150 names and numbers.

Press the

MENU/OK/MUTE button, to

see

“PHONE BOOK”.

Press the

MENU/OK/MUTE button,

UP or DOWN

and then press the buttons until you see "MEM STATUS".

Press the

MENU/OK/MUTE.

Then the display will show the phonebook
memory space available e.g. if you have saved 30 names and numbers in
your phonebook, it would display 30/150.

Press

the PHONE BOOK/BACK

until you return to idle mode.

Making calls from the phonebook

Reviewing phonebook memory status

Note: For a short-cut to finding the name, you can press the digit buttons to go
directly to the first entry beginning with the corresponding letters of that key,
and then scroll from there.

or

the call

Binatone Help Line : 0845 345 9677 17

To subscribe to this feature, you need to contact your service provider, and there may

be a charge for this service. Caller Display lets you see the phone numbers of your callers
on the display, before you answer.

The base and each handset will store its own CID list independently. Both answered and

unanswered calls are stored, up to a maximum of 20 calls. When the caller display list is
full, any new caller display entry will replace the oldest record.

If you receive a new call, the display will show the icon with the name and number
of the caller.

If there are no items on the CID list, the display will show NO CALLS.

The display may al so show the following:

UNAVAILABLE – if the number of the caller is unavailable, e.g. from an international call.

WITHHELD – if the call is from someone who has withheld their number, e.g. by dialling 141

Press the MENU/OK/MUTE button, to see PHONEBOOK.

Press the DOWN button, to see "CALL LOG".

Press the MENU/OK/MUTE button, to see “RECEIVED”.

Press the MENU/OK/MUTE button, to see the most recent

record in the CID list.

Press the UP or DOWN buttons to scroll through the CID list. The NEW

icon will

*If you wish to call directly from the CID list, press the SPEAKERPHONE button or lift up
the handset to dial the number automatically.

New CID log

To review the CID list

Caller Display (CDS) / Caller ID (CID)

be displayed in the idle screen until all new calls have been viewed in the CID list.

Note: To go directly to the first record of the CID list,

Press the UP or DOWN buttons in standby mode.

The caller display information includes:

- the caller's number (up to 20 digits)

- the date and time of the call

- the caller's name (up to 12 characters) if the incoming number matches an entry

Note: it will also display the caller's name if the network sends it, but this is not normally

in the Phonebook

available in the UK.

or

or

Binatone Help Line : 0845 345 9677 18

Enter name using keypad.

Press

the MENU/OK/MUTE

button to confirm the name.

The display will move the flashing bar to the end of the number position.

If the number needs modifying use the keypad to enter digits or
the DELETE button to delete.

Use the UP or

DOWN buttons to scroll through the melodies.

Press the MENU/OK/MUTE button to confirm your selection.
You will hear a confirmation tone, and the display will return to the CID list.

Repeat the steps above to review the CID list, and to locate the record you
want to store in the phonebook.

Press the MENU/OK/MUTE button to see “ADD TO PB ?”.

Press the MENU/OK/MUTE button to confirm, and the display will show a

To store a Caller ID contact in the phonebook

Repeat the steps above to review the CID list.

To delete all Caller ID records

Press the MENU/OK/MUTE button, to see ADD to PB?

Press the DOWN button twice to see DELETE ALL?

Press the MENU/OK/MUTE button twice, you will hear the completion tone
and the display will show

EMPTY

.

flashing bar at the beginning of the name position.

Press the MENU/OK/MUTE button to confirm the number, and the
display will show "MELODY 1".

Repeat the steps above to review the CID list, and to locate the record

To delete a Caller ID record

Press the MENU/OK/MUTE button, to see ADD to PB?

Press the DOWN button, to see DELETE?

Press the MENU/OK/MUTE button twice, you will hear the completion tone
and the display will return to the Caller ID list.

you want to delete

or

Binatone Help Line : 0845 345 9677 19

Ringer volume, melody

You can adjust the volume level of the intercom ringer (INT RING) and the external call

Press the

MENU/OK/MUTE

button.

Scroll

DOWN until you see “SETTINGS”.

Then press

the MENU/OK/MUTE

button.

Scroll

DOWN until you see “RING SETUP”.

Press the

MENU/OK/MUTE

button. Then it will display "INT RING"

or scroll DOWN

to select

“EXT RING”.

Press

the MENU/OK/MUTE

button. The display will show "MELODY".

Scroll

DOWN until you see “VOLUME”.

Then press

the MENU/OK/MUTE

button to select and the display will show

“VOLUME 2”.

Press the UP or DOWN button to scroll through the volume settings.

(from OFF, 1 to 5).

Then press the

MENU/OK/MUTE

button to confirm the setting

Press

the PHONEBOOK/BACK

button to return to the previous menu

To change ringer volume

ringer (EXT RING) independently, with settings from 1 (quietest) to 5 (loudest), or turned OFF.

There are 10 base ringer melodies from 1 to 10

To change ringer melody

Press the MENU/OK/MUTE button.

Scroll

DOWN until you see “SETTINGS”.

or

Binatone Help Line : 0845 345 9677 20

Press the UP or DOWN button to scroll through the Melody list (from 1 to 10).

Then press the MENU/OK/MUTE button to confirm the setting.

Press the PHONEBOOK/CANCEL buttonto return to the previous menu.

Then press the MENU/OK/MUTE button.

Scroll DOWN until you see “RING SETUP”.

Press the MENU/OK/MUTE button. Then it will display “INT RING”

or scroll

DOWN to select “EXT RING”.

Press the MENU/OK/MUTE button. The display will show “MELODY”.

Then press the MENU/OK/MUTE button to select and the display wil l show

“MELOD Y 1”.

or

Binatone Help Line : 0845 345 9677 21

Using a multi-handset system

Press the INTERCOM button. If you have only one cordless handset registered

to the base, the display will show "CALLING HS1" and the base will beep.

If you have more than one handset registered to the base, the display will
show "HS?" with the registered handset numbers above, and the base will
output a continuous beep, until you press the number for the handset you
want to intercom. Then the display will change, for example, to "CALLING HS2",
if it is handset 2 that is being called. 

If you enter a number that is not available the base will return to idle mode.

The handset being called will ring with its selected melody and display

"BASE CALLING".

When the phon e rings and the display shows "HS 1 CALLING",

you

can answer the

call by pressing the SPEAKERPHONE button or picking

up the handset.

If you want to end the intercom, press the SPEAKERPHONE

button or

replace the handset.

During a call, it is possible to transfer a call to another handset.

During an external call, if you want to transfer the call to a cordless handset,

press the INTERCOM button. The external call will be put on hold.

If the base has only one cordless handset registered it will immediately start calling
that handset, but if more than one handset is registered enter the number for the
handset you want to transfer the call to.

When the handset answers the intercom call, simply hang-up at the base to 
transfer the call.

To Make Intercom calls

To Transfer intercom call

If you do not enter any number for 1 minute the handset will return to idle mode.

To cancel the intercom call press the INTERCOM button again.

Receiving an intercom call from a cordless handset.

[1][2]…

Binatone Help Line : 0845 345 9677 22

During an external call it is possible to conference in another handset.

During a call, press the INTERCOM button and enter the number of the handset
you want to connect to, by using the keypad.

The display will show the handset name you have entered and the other
handset will ring. If the number you have entered is not available, you will
hear an ERROR tone and the call will be returned to the original handset.
If you do not enter any number within 30seconds the call will also be
returned to the original handset.

Once the other handset answers the call, press STAR( ) button and the display
will change from "INTERCOM" to "CONFERENCE", and both the base and the

Receiving a conference call.

When you receive intercom ringing from a handset, answer the call and the
display will show "INTERCOM". Then wait for the other handset to initiate

To answer, pick up the handset or press the SPEAKERPHONE button and the
display will show “INTERCOM”.

Either handset can just hang-up to end the call and the other handset will
still be connected.

To Set up a three-way conference

cordless handset will be connected to the external call.

When either the base or the handset hangs up, the other will still be
connected to the external call.

the three-way conference call.

If the handset does not answer within 30 seconds, the transfer will be cancelled and

Receiving a transfer call from a cordless handset.

When you have an intercom call transfer your handset will ring and the
display will show

“HS 1 CALLING”

.

To answer the call, pick up the handset and you will be connected.

If you want to end the intercom transfer, hang-up the phone.

the external call reconnected to the base.

Alternatively, once the intercom ringing starts and the display shows, for example,

"

CALLING HS1", you can hang-up the phone to transfer the call automatically.
The display will change to "TRANSFER HS1". The called handset will ring for 1
minute, but if it does not answer, both the base and handset will ring for another
minute.If neither answers, the ringing will stop and the external call will be released.

Page / locate a handest

Press the INTERCOM button. If you have only one cordless handset registered

to the base, the display will show "CALLING HS1" and the base will beep.

If you have more than one handset registered to the base, the display will
show "HS?" with the registered handset numbers above, and the base will
output a continuous beep, until you press the number for the handset you
want to page. Then the display will change, for example, to "CALLING HS2",
if it is handset 2 that is being paged. 

If you enter a number that is not available the base will return to idle mode.

If you do not enter any number for 1 minute the handset will return to idle mode.

Handset registration

To register new handsets to the base:

The handset(s) supplied with your CC2310 system are already registered

!

— the first one as handset number 1, the second as number 2...etc

You don’t need to re-register them, unless you have a problem.

To check whether a handset is registered, make sure mains power to the base

unit is switched on and the handset is within range. The handset’s display

should show its number, and the ‘signal level’ symbol on the display should

show three bars. If the display shows "UNREGISTERED" , you need to re-register

the handset using the following process:

You need to operate the base and handset together:

1. On the handset, press the MENU/OK button to see

2. Press the UP

3. Press the MENU/OK button to see

If the handset already has a registration to a base there is a "+" on the right side of
the display, and you should choose another base number if you don't want to
lose that one.

button twice to see

Binatone Help Line : 0845 345 9677 23

"PHONEBOOK"

"REGISTRATION"

"BASE 1"

4. Press the DOWN

5. Press the MENU/OK button to see

6. Press the MENU/OK button to confirm, and the
"SEARCHING 1" (or 2,3,4)

7. At the same time, on the base, press

"PHONEBOOK"

8. Press the UP button tweice to see

9. Press the MENU/OK button to see

After a short delay, if the registration is successful, there will be a

confirmation beep, and the Handset display will go back to idle mode with

the new handset number shown (e.g. HS1, HS2). The base display will also

a three-way conference

go back to idle mode.

To de-register a handset

You may need to do this if you need to replace a faulty handset. Call the Binatone

help

line if you need more advice.

To de-register a handset using the CC2310 base menu

With the base in idle mode:

1. Press the MENU/OK button to see
2 .Press the DOWN button twice to see

3. Press the MENU/OK button to see

4. Press the MENU/OK button to see

Press the UP or DOWN button to select the handset you want to
de-register.

5. Press the MENU/OK button to confirm, and the selected handset will

be de-registered. (The display on the handset that has been deleted

will show "UNREGISTERED".)

/C

Press the PHONEBOOK/BACK button to return to the previous menu

*

at any time.

Note: Handsets can also be de-registered using another cordless handset,
as described in the cordless handset user guide.

button to select a base number (BASE 1, 2,3 or 4)

(key in 4 digits pin code -- 0000)

"PIN ?"

display will flash

the MENU/OK button to see

"REGISTRATION"

"SEARCHING" flash on base display

"PHONEBOOK"

"SETTINGS"

"DELETE HS"

" HS 1 " (or 2,3, 4)

Binatone Help Line : 0845 345 9677 24

Telephone answering machine (TAM) setup

The CC2310 answering machine can record messages from incoming callers or memos
directly at the base. Each message/memo can be up to 2 minutes long, and the total

recording time available for all messages/memos is about 60 minutes. If the memory

becomes full, the Message Light will flash rapidly, and you will need to delete some

messages to create space before any more messages can be recorded.

You can switch the answering machine OFF or ON, and when it is ON, select an Answer

and Record mode or an Answer Only mode.

The Answer and Record mode allows a caller to leave a message, and is set when

OGM1 (Out Going Message 1) is selected.

The Answer Only mode, does not allow a caller to leave a message, and is set when
OGM2 (Out Going Message 2) is selected.

The answering machine is supplied with pre-set announcements for OGM1 and OGM2,
but you can record your own personal announcements if you wish.

When the answering machine is ON it will answer after a set number of rings (default 5),
but you can change the number of rings if you wish.

When the answering machine is OFF, or if the memory is full, it will answer after 15 rings,
which allows remote access if required.

Switching TAM on/off

1. By Hotkey

(1)

Switch TAM on to OGM 1 or OGM 2

If the TAM is turned off, the display will show “TAM OFF”

12:00 9/08

TAM OFF

.

To Set up a three-way conference

Binatone Help Line : 0845 345 9677 25

Binatone Help Line : 0845 345 9677 26

2. By MENU

Alternatively, you can switch the TAM ON or OFF using the Base menu system.

Press the MENU/OK/MUTE show "PHONEBOOK".

Press the UP button to show "TAM",

Press the UP button to show "TAM SETTINGS".

Press the MENU/OK/MUTE button to show "TAM ON/OFF".

Press the UP or DOWN button to choose "ON" or "OFF".

Press the UPor DOWN button to choose "OGM1" or "OGM2", depending on

and then the MENU/OK/MUTE button to select it.

Press the MENU/OK/MUTE button to show "ON" or "OFF".

whether you want to set answer and record (OGM1) or answer only (OGM2).

Press the MENU/OK/MUTE button to select it, and the display will

Press the PHONEBOOK/BACK button to return to the previous menus.

return to "TAM ON/OFF".

(2)

If the TAM is already switched on, either with OGM 1 or OGM 2.

Press and hold

STOP/ON/OFF

for over 2 seconds to switch the TAM off.

Then the display will show “TAM OFF”

.

Switch TAM off

Press and hold STOP/ON/OFF for over 2 seconds to switch TAM on.

Then you can see

“OGM 1”

on the display and hear the voice prompt

“Answer ON, Announcement One”.

After this, the display will show the number of messages.

You can switch bet ween OGM 1 and OGM 2 by pressing STOP/ON/OFF

briefly, provided the TAM is already ON.

12:00 9/08

00/02 MSGS

Press the MENU/OK/MUTE button to select it.
If "ON" is selected, the display will then show "OGM1" or "OGM2"

or

or

Binatone Help Line : 0845 345 9677 27

OGM1 is set as the default announcement when you set up the CC2310 for the first time.
If you want you can record your own personal announcement of up to 60
seconds for each OGM.

1. By Hotkey

(1)

(2)

The pre-set announcement for OGM1 is “Sorry we cannot
answer your call now, please leave your message after the beep".

If you want to record your own OGM 1 message, first ensure OGM1 is set
as the outgoing message.

Then press and hold REWIND/OGM, you will see “OGM 1” on the
display and hear a voice prompt “PLEASE RECORD NEW
ANNOUNCEMENT AFTER THE BEEP”.

After a beep tone, the display will show “RECORD”
and then you can start speaking.

When you want to end the recording, press STOP/ON/OFF.
Then the unit will playback the OGM 1 announcement automatically.

The pre-set announcement for OGM2 is

“Sorry I cannot answer your call now, please call later” .

The unit will automatically switch to OGM 2 to answer a call when the
memory is full.

If you want to record your own OGM2 message, first ensure OGM2

Repeat above sequence as OGM 1 to record the OGM 2 announcement.

2. By MENU

Alternatively, you can record OGM1 or OGM2 using the Base menu system.
Press the MENU/OK/MUTE to show "PHONEBOOK".

Press the UP button to show "TAM",

To Record your Outgoing Message (OGM)

To record OGM1

To Record OGM 2

is set as the outgoing message.

and then the MENU/OK/MUTE button to select it.

Binatone Help Line : 0845 345 9677 28





Press the UP button to show "TAM SETTINGS".

Press the MENU/OK/MUTE button to show "TAM ON/OFF".

Press the DOWN button to show "SET OGM".

Press the MENU/OK/MUTE

button to show 

"OGM1"

Press the UP or DOWN button to choose "OGM1" or "OGM2"

Press the MENU/OK/MUTE button to select it and show "PLAY".

Press the DOWN button to show "RECORD".

Press the MENU/OK/MUTE button to hear a voice prompt "PLEASE RECORD

NEW ANNOUNCEMENT AFTER THE BEEP". After a beep tone you can start 

speaking.When you want to end the recording, press STOP/ON/OFF. Then the
unit will playback the OGM announcement automatically.

or

1. By Hotkey

Press the REWIND/OGM briefly to listen to the current OGM (OGM 1 or
OGM 2).

2.

By MENU

Press the MENU/OK/MUTE button to show "PHONEBOOK".

Press the UP button to show "TAM".

Press the DOWN button to show "SET OGM".

Press the MENU/OK/MUTE to show "OGM1".

Press the UP or DOWN button to choose "OGM1" or "OGM2".

Press the MENU/OK/MUTE button to select it and show "PLAY".
Press the MENU/OK/MUTE button to play the OGM.
Once the playback has finished, the display will return to the previous menu.

Press the PHONE BOOK/BACK until you return to idle mode.

To playback the OGM

Press the MENU/OK/MUTE button to show "MESSAGE".

Press the UP button to show "TAM SETTINGS".

Press the MENU/OK/MUTE button to show "TAM ON/OFF".

or

Binatone Help Line : 0845 345 9677 29

Switch between OGMS

When the answering machine is switched ON you can select OGM1 or OGM2.

Press the STOP/ON/OFF and if you hear "ANSWER ON,ANNOUNCEMENT 1",
you are currently using OGM1.

If you want to switch to OGM2, press the STOP/ON/OFFagain, and you will hear
"ANSWER ON, ANNOUNCEMENT 2". If you want to switch it back on to OGM1,

Press the UP button to show "TAM SETTINGS".



Press the MENU/OK/MUTE button to show "PHONEBOOK".

Press the UP button to show "TAM".

Press the MENU/OK/MUTE button to show "MESSAGE". 

Press the UP button to show "TAM SETTINGS".

Press the DOWN button to show "SET OGM".

Press the MENU/OK/MUTE button to show "OGM1".

Press the UP or DOWN button to choose "OGM1" or "OGM2".

Press the MENU/OK/MUTE button to select it and show "PLAY".

Press the UP or DOWN button to show "DEFAULT".

Press the MENU/OK/MUTE and the display will show “CONFIRM?”

Press the MENU/OK/MUTE to confirm. You will hear a beep, the display will
return to

“DEFAULT”

.

Press the PHONE BOOK/CANCEL until you return to idle mode.

To delete the OGM (SET OGM to DEFAULT)

Press the MENU/OK/MUTE button to show "TAM ON/OFF".

SwiSw

i

or

Binatone Help Line : 0845 345 9677 30

The CC2310 can answer calls after 2 to 9 rings. If you don’t set a number, it will
answer after 5 rings.

If you want to dial in and check your messages while you’re away, you can set

TOLL

SAVER – if there are new messages, the CC2310 will answer the call after 2 rings.

If there are no new messages, it will answer after 5 rings. So, if you call in and you
don’t get an answer after 2 or 3 rings, you can hang up and save on call charges.

Press

the MENU/OK/MUTE.

Scroll UP until “TAM”,

Press the MENU/OK/MUTE and you will see “MESSAGE ”.

Scroll UP until the display shows “TAM SETTINGS”.

Then press the MENU/OK/MUTE and you will see “TAM ON/OFF”.

Scroll

DOWN

until the display shows

“SET RING”

then press the MENU/OK/MUTE and the display will show “5 RINGS”.

To Set Ring number

Scroll UP or DOWN to select your choice.

Then press the MENU/OK/MUTE and the display will return the to previous menu.

Scroll UP or DOWN to select ALARM ON or ALARM OFF.

Onceselected press the MENU/OK/MUTE

and the display will return to the previous menu.

Press the PHONE BOOK/BACK until you return to idle mode.

You can set a new message alert tone which is normally turned off by default.
When the tone is turned on, you will hear this audible warning tone every

Press the MENU/OK/MUTE.

Scroll UP until “TAM”,

Press the MENU/OK/MUTE and you will see “MESSAGE”

.

Scroll UPuntil the display shows

“TAM SETTINGS”

.

Then press the MENU/OK/MUTE and you will see “TAM ON/OFF”

Scroll DOWN until “TAM AL ERT”

Then press the MENU/OK/MUTE and
the display will show “OFF” which is the defa ult setting.

To Set TAM alarm

60 seconds, if you have new messages.

.

Press the PHONE BOOK/BACK until you return to idle mode.

or

or

Binatone Help Line : 0845 345 9677 31

If the answering machine is ON and set for OGM1, when there is an incoming call, the
answering machine will answer it and play the OGM, followed by a "beep". The caller can
then leave a message of up to 2 minutes on the answering machine. The caller's voice

x You can use the corded handset, the speakerphone or the cordless handset to

intercept the call to speak to the caller during ICM recording. Then the message that
is currently being recorded will be saved as a new message unless the user presses
STOP during the message, and then the message will not be

x

You can pick up a parallel phone to intercept the call, and the message will be

Incoming Call Messages (ICM)

saved up to then.

will

also be played through the loudspeaker to allow you to screen the call and decide if

you want to leave the answering machine to record the message, or if you want to talk to

the caller directly.

This allows users to record amemo of up to 120 seconds. Memos count as
messages when played

Press and hold MEMO/SKIP key and the display will show"MEMO" and you

will hear "Please record memo after the beep". Then the display will show

When you want to end your memo recording press the STOP/ON/OFF.

x

If the memory is full, during the memo recording, you wil l hear SORRY, THE
MEMORY IS FULL and the display will return to idle mode.

To record a memo on TAM

"RECORD" and the current recording time.

To play/pause messages on TAM

If you have new messages, the Message light will flash and the
display will show e.g. 01/02 MSGS, which means you have 1 new message/2

messages altogether.

* There is approximately 60 minutes of recording time on the TAM.

Press the PLAY/PAUSE to listen to messages and memos. Press the
PLAY/PAUSE if you want to pause during a message.

Press the OGM/REWIND if you want to skip back to the previous message.
Press the MEMO/SKIP

if you want to skip forward to the next message.

Press the STOP/ON/OFF if you want to stop the message playback.

saved as a new message.

Binatone Help Line : 0845 345 9677 32

Press the DELETE while a message is playing. You will hear
"MESSAGEDELETED"and the current or memo playing will be

Press and hold DELETE for 2 seconds at any time to delete all old messages.

You will hear "ALL MESSAGES DELETED", and all old messages

To delete a message on TAM

To delete all messages on TAM

DEL

DEL

adeleted, and if there are more messages the next message will start to play.

NOTE: You cannot delete New Messages, so you will have to start to play
them before trying to delete them.

The security code is used to access the remote control or default the TAM,
and is a 4-digit code. The default code is “0000”.

Press the MENU/OK/MUTE. Scroll UP until “TAM”, press the

MENU/OK/MUTE and you will see “MESSAGE”.

Scroll UP until the display shows “TAM SETTINGS”. Then press the
MENU/OK/MUTE and you will see “TAM ON/OFF”.

Scroll the DOWN until the display shows “TAM PIN”. Then press the
MENU/OK/MUTE and the display will show the current setting “0000”.

Use the keypad to enter the new security PIN code.

Press the MENU/OK/MUTE and you will hear a beep. This display will
return to the previous menu.

Press the PHONE BOOK/BACK until you return to idle mode.

To Change Security Code (TAM PIN)

will be deleted.

Binatone Help Line : 0845 345 9677 33

x

If the machine is switched off or the memory is full, it

will answer the call after 15 rings

and allow the caller to switch the machine ON, or check the messages from a remote

x When you hear the OGM announcement, key in the 4-digit security code and, if the

x

When messages are playing you can press keys as follows:

o

Press 1 – To repeat the current message

o

Press 1 twice – To skip back to the previous message

o Press 2 – To pause and restart the current message
o Press 3 – To skip forward to the next message
o Press 6 – To stop playback
o Press 7 – To delete current message
o Press 0 – To delete all old messages

o Press 1 – To play the main menu
o Press 2 – To play messages
o Press 4 – To play the Announcement (OGM)

x When there are no more voice prompts or messages playing, if you do not

press a button within 10 seconds your CC2310 will hang up.

x

Pressing the STOP or picking up the phone during remote operation will also stop
the remote operation.

x

During remote control mode, press # twice to re lease the line.

If the TAM memory is full the Message Light will flash rapidly, the TAM will answer the
call after 15 rings and then announce “

Sorry we cannot answer your call now,

please call later. Sorry memory full."

Enter the security code to enter the remote mode. Once you have freed up some
memory space, the machine will automatically return to the Answer ON mode.

Remote Operations

If you are away from home you can call your answering machine to check your messages.
You will need to use tone dialling (also called MF or DTMF) to dial the numbers to access

and control your answering machine from a remote location.

x

security code is correct, you will hear a voice prompt telling you if you have any

messages. If so, it will start playing them, but if not it will announce "Press 1 to play

main menu". Follow the instructions from the menu list or those given below.

x

When in remote, but not playing messages, you can press keys to start functions

o Press 5 – To record a new Announcement (OGM)
o Press 8 – To switch the answer machine off
o Press 9

– To switch the answer machine on and switch between 

o Press 0 – To delete all old messages

OGM1 and OGM2

location.

Binatone Help Line : 0845 345 9677 34

You will restore the following settings af ter you select this command.

- Ring setting: 5

- TAM ON - OGM 1

- Security code: 0 0 0 0

- TAM Alarm: OFF

Press

the MENU/OK/MUTE.

Scroll DOWN until “TAM”,

Press the MENU/OK/MUTE and you will see “MESSAGE”

.

Scroll DOWN until the display shows “TAM SETTINGS”.

Then press the MENU/OK/MUTE and you will see “TAM ON/OFF”.

Scroll the DOWN until the display shows “TAM DEFAULT”.

Then press the MENU/OK/MUTE and the display will show “PIN CODE?”.

Enter the PIN code using the keypad.

Then press

the MENU/OK/MUTE

to confirm, and the TAM

To Reset TAM to default settings

settings will be defaulted.

Binatone Help Line : 0845 345 9677 35

SOS call function

The SOS call function is very useful for people at home to make an emergency
call to ask for help from their relatives, police, doctor, etc.

x Press and hold SOS button for more than 5 seconds.

x

The loudspeaker on the base unit gives a loud SOS alert tone for 30s to alert people in
the house first.

x

The line is automatically seized and dials to each of the pre-stored SOS numbers,

x

If the SOS voice prompt is recorded, it will send the announcement to the line

continuously for 1 minute so that the called party will hear the announcement when he
answers the call. After finishing the announcement for 1 minute, it will drop the call.

x

If the SOS voice prompt is not yet recorded, after the SOS number is dialled out, it

will wait for 1 minute and then drop the call.

x

Then it makes another call to the second SOS number, if programmed, and

sends the

announcement to line for another 1 min.

x

Finally it will make another call to the third SOS number, if programmed, and send

x

When the SOS call function is active, you can only terminate this function

by

lifting up the corded handset on the base. It can not be terminated byusing any
buttons

on the cordless handset.

User is allowed to set up to 3 SOS numbers and 1 SOS voice recording.

Press the MENU/OK/MUTE.

Scroll DOWN until you see “SOS SETTINGS”

.

Press the

MENU/OK/MUTE

and you will see

“SOS NUMBER”

.

Press the MENU/OK/MUTE and you will see “SOS NUMBER 1”.

Scroll the UP or DOWN to select SOS NUMBER 1 to 3.

How SOS call function works

How to terminate SOS call function

To Set SOS numbers

starting with the first.

the announcement to line for another 1 minute.

Then press the MENU/OK/MUTE to select the one you want to program.

or

Binatone Help Line : 0845 345 9677 36

You can record an SOS message of up to 60seconds.

Press the

MENU/OK/MUTE. Scroll the DOWN until you see

"SOS SETTINGS”.

Press the MENU/OK/MUTE and you will see “SOS NUMBER”.

Scroll the DOWN until the display shows “SOS VOICE” then press the
MENU/OK/MUTE. The display will show “PLAY”.

Scroll the

DOWN

until the display shows “

RECORD”,

then

press The MENU/OK/MUTE to record. The display will show the recording
counter (You have up to 60seconds To record).

Press the STOP/ON/OFF to end the recording.

Press the PHONE BOOK/BACK until you return to idle mode.

Press the MENU/OK/MUTE. Scrtheoll DOWN until you see “SOS SETTINGS”.

Press MENU/OK/MUTE and you will see “SOS NUMBER”.

Scroll theDOWN until the display shows “SOS VOICE” then press the

MENU/OK/MUTE.

The display will show “

PLAY”.

Then press the MENU/OK/MUTE to play the current SOS voice message.

Press the STOP/ON/OFF to stop the playback.

Press the PHONE BOOK/BACK until you return to idle mode.

To Record SOS voice prompt

To Playback the SOS voice prompt

Enter the phone number.

Then press the MENU/OK/MUTE. You will hear a beep and the number is
saved.

If you want to save more SOS numbers, press the DOWN to select the next
location you want to program,and repeat above steps.

Press the PHONE BOOK/BACK until you return to idle mode.

Binatone Help Line : 0845 345 9677 37

Advanced use of your phone

Press the MENU/OK/MUTE.

Scroll DOWN until you see “SETTINGS”.

Press the MENU/OK/MUTE and then you will see “DELETE HS”.

Then scroll DOWN until you see “KEY TONE”.

Press the MENU/OK/MUTE

and the display will show “ON”.

Press the UP or DOWN button to select ON or OFF on the display.
Press the MENU/OK/MUTE button to confirm the option, and you will
hear the confirmation beeps.

The display will return to "KEY TONE".

Press the PHONE BOOK/BACK until you return to idle mode.

The Recall (also called Flash) may be needed if you use BT calling functions or are
connected to a PABX.

Press the

MENU/OK/MUTE.

Sc roll the

DOWN until you see “SETTINGS”.

Press the MENU/OK/MUTE and then you will see “DELETE HS”.

Scroll the DOWN until you see “FLASH TIME ”.

Press the MENU/OK/MUTE and the display will show

Press the UP or DOWN button to show the flash time you want on the display.

Press the MENU/OK/MUTE button to confirm the option, and you will hear
the confirmation beeps. The display will return to "FLASH TIME".

Press the PHONE BOOK/BACK until you return to idle mode.

To Turn on/off key tone

To Set Flash (Recall) time

The default setting of this CC2310 telephone is 100ms, and normally this
will be correct for the UK.

However, if necessary, you can select from 3 flash times: 100ms, 250ms and 600ms
to meet your telephone line or PABX requirement.

the current the Flash time, e.g. "100" ms.

or

or

Binatone Help Line : 0845 345 9677 38

This allows you to restore base settings to their default settings:

Ext Ringer Volume = 5

Press

the MENU/OK/MUTE, scroll DOWN until you see SETTINGS.

Press the MENU/OK/MUTE then scroll DOWN until you see “BS DEFAULT”.

Press the MENU/OK/MUTE and the display will show "PIN ? "

Enter the PIN code using the keypad. (Default PIN is 0000)

Press the MENU/OK/MUTE and you will hear the confirmation beeps and
the display will return to idle mode.

Ext Ringer Melody = 1

To Set Base to default settings

Int Ringer Volume = 5

Int Ringer Melody = 2

Dial Mode = TONE

Flash Time = 100ms

Key Tone = ON

Language = ENGLISH

PIN CODE = 0000

The Caller Display (CID) and Redial lists will be erased, but the Phonebook memories 
and TAM settings will remain unchanged.

However, for some old telephone lines or PABX systems you may need to change

Press the MENU/OK/MUTE.

Scroll DOWN until you see “SETTINGS”.

Press the MENU/OK/MUTE and then you will see “DELETE HS”.

Scroll the DOWN until you see “DIAL MODE”. Prethe ss MENU/OK/MUTE

Press the MENU/OK/MUTE and the display will show
the current setting of Dialling Mode e.g. "TONE" or PULSE”.

Press the UP or DOWN button to show the dialling mode you want on 

Press the MENU/OK/MUTE button to confirm the option, and you will hear the 
confirmation beeps. The display will return to "DIAL MODE" .

Press PHONE BOOK/BACK until you return to idle mode.

To Set Dialling Mode (Tone/Pulse)

the dialling mode from Tone to Pulse.

or

The default setting of this CC2310 telephone is TONE (also called Touch Tone, MF or DTMF),

and normally this will be correct for the UK, so will not need to be changed.

the display.

Binatone Help Line : 0845 345 9677 39

Some functions (including handset registration) require a PIN code. The default PIN is
0000 but you are able to change to your personal 4-digit PIN.

Press the MENU/OK/MUTE button.

Then scroll

DOWN until you see “SETTINGS”.

Then press the MENU/OK/MUTE button.

Then scroll DOWN until you see “MODIFY PIN”.

Press the MENU/OK/MUTE button and the display will show "PIN ?"

Enter the PIN code using the keypad (if you haven’t changed it, the
default PIN is 0000).

Press the MENU/OK/MUTE button and the display will show

“NEW PIN”.

Use the keypad to enter the new PIN (4 digits from 0-9).

Press the MENU/OK/MUTE button to confirm and the display will show

"REPEAT"

Use the keypad to enter the new PIN again and press the MENU/OK/MUTE
button to confirm. You will hear the confirmation beeps and the display

will return to "MODIFY PIN".

Press the PHONE BOOK/BACK until you return to idle mode.

* If you enter the wrong PIN at any time you will hear an error tone and the display will return

to the previous menu.

To Change the PIN code

Binatone Help Line : 0845 345 9677 40

Troubleshooting

ALWAYS check
first that:

x

You have followed all the steps listed onpages 5 & 6 to install
and set up your CC2310

x All

connectors

are firmly inserted in their sockets

x Mains power to the base unit is switched on at the socket

x

The handset’s batteries are correctly and securely installed
and are not run down

Everyday use

“I cannot make or
answer calls ”

x Check that the base unit’s

mains power adapter

is plugged

in and power is switched on. The base unit needs mains
power for norm al operation of the phone – only the basic

handset calling works without mains power.

x

Make sure you are using the telephone line cable supplied
with your CC2310. Other telephone line cables might
not work.

x

Switch off power at the mains socket, wait for a few
seconds and then switch back on. This may solve the
problem.

“I cannot make a
call”

x

Only one handset (or the base unit) can be connected to the
outside line at once. If a cordless handset is already using
the line, you need to wait until it’s finished its call.

“The phone does
not ring”

x

Check that the base unit’s mains power adapter i s plugged
in and power is switched on. The base unit needs mains
power for norm al operation of the phone – only the basic
handset calling works without mains power.

x

Make sure you are using the telephone line cable that wa
supplied with your CC2310. Other telephone line
cables might no t work

x

You need to subscribe to the Caller Display feature from
your network service provider. You should find contact
details on your phone bill.

“The Caller Display
feature isn’t
working”

x

The caller may have withheld their number by dialling 141.
Or they may be calling from a network that does not transmit
the caller’s number (e.g. it may be an international call.)

Binatone Help Line : 0845 345 9677 41

x

Make sure you’ re holding the earpiece correctly over your
ear.

“The volume in the
earpiece is low
when I’m on a call”

x Adjust t he volume using the UP/ DOWN button.

Intercom and transfer

x

Make sure the other handset is in range of the base unit.

“I can’t transfer a
call”

x Make sure you are dialling the correct number for the ot her

handset.

If the fault persists…

x

Disconnect all other instruments

connected to the same

line as the CC2310 and try to make a call

x

Disconnect the base unit from the telephone line and p lug
a different phone into the master telephone socket. Try
making a call. If this works, the line is OK.

x

If the call does not work, and you are using a two-way
socket adapter, remove it and plug a telephone directly into

the socket. I f the call now works, t he adapter may be faul ty.

x If you cannot make a call, the fault may be on the exchange

line. Contact the service provider (the BT engineers on 151

for UK only, or your cable company).

x

If you still cannot identify the cause of the problem, contact
the Binatone on 0845 345 9677 (UK only).

“When I try to
make a call, I hear
Busy tone.”

x

If you’re using a CC2310 multi-handset system, check
whether other handsets are already on a call.

Binatone Help Line : 0845 345 9677 42

Cleaning and care

Do not clean any part of your CC2310 with benzene, thinners or other

solvent chemicals – this may cause permanent damage which is not covered by
the Guarantee. When necessary, clean it with a damp cloth.

Keep your CC2310 away from hot, humid conditions or strong sunlight,

and don’t let it get wet.

Every effort has been made to ensure high standards of reliability for your

CC2310. However, if something does go wrong, please do not try to repair
it yourself – consult your supplier or the Binatone Helpline.

Declaration of conformity

The cordless phone, identified as CC2310, complies with the essential protective
requirements and objectives of:

EC R&TTE Directive 1999/5/EC
EC Low Voltage Directive 2006/95/EC
EC EMC Directive 89/336/EEC

And conforms to the following relevant harmonized standards:

Radio: EN 301406
EMC: EN 301489
Safety: EN 60950

The conformity to the requirements is validated by the

symbol.

NOTE: In compliance with Directive 2002/96/EC, when you purchase
a product that comes with the symbol shown on the right, you are
required to dispose the electrical and electronic equipment by separate
waste collection and you cannot dispose of the product as normal
waste. This equipment and all its components, subsystems and
consumable m aterials form an

integral part of this product and wh en
you decide to dispose them, you have to bring them to the local
recycling centr es for appropriate waste disposal, in compliance with
the current regulations. Details about the location of these centres can
be obtained from your local authority.

Binatone Help Line : 0845 345 9677 43

Guarantee and service

The CC2310 is guaranteed for 12 months from the date of purchase shown on your
sales receipt. This guarantee does not cover any faults or defects caused by accidents,

misuse, fair wear and tear, neglect, faults on the telephone line, lightning, tampering with

Please keep your sales (till) receipt – this is your guarantee. You should also keep
the original packaging material .

In the unlikely event that you need to return your CC2310 to our Repair Centre
while it is under guarantee, there will be a £5 handling charge.

While the unit is under Guarantee

1. Disconnect the base unit from the telephone line and the mains electricity supply

2. Pack up all parts of your CC2310, using the original packaging. Remember to

include the m ains adapter

3. Return the unit to the shop wher e you bought it, making sure you take your sales

receipt.

After the Guarantee has expired

If the unit is no longer under Guarantee, first follow steps 1 and 2 as for repair under
Guarantee.

Then…

3. Cal l Binatone Helpline on 0845 345 9677 (for UK only) and ask for a quotation of

the repair charge and details of where to send your CC2310 for repair.

4. Make sure you include with your CC2310:



Your name and address

A cheque or postal order for the value of the repair charge

5. Return your CC2310 to the address given by the Service Department.

* This does not affect your statutory r ights.

the equipment, or any attempt at adjustment or repair other than through approved agents.

Binatone Help Line : 0845 345 9677 44

Technical details

Standard Digital Enhanced Cordless Telecommunication (DECT)

Frequency range 1.88 to 1.9 GHz (bandwidth = 20 MHz)

Channel bandwidth 1.728 MHz

Operating range Up to 300m outdoors; up to 50m indoors

Operating time Standby: 150

hours

Talking: 9 hour

s

Battery charge time: 15 hours

Temperature range Operating 0 ºC to 40 ºC

Storage -20 ºC to 60 ºC

Electrical power

HANDSET – two pcs of AAA-size 550mAH Ni MH 1.2V rechargeable batteries

Base UNIT – input 230VAC 50Hz; output 7.5VDC – 500mA

CHARGER POD – input 230VAC 50Hz; output 6VDC – 200mA

Port specification The port (connect to the mains power supply) is a SELV
port with r espect to EN41003.

The

port (connected to the telephone line) is a TNV port with respect to

EN41003.

PBX compatibility:

Timed break recall (flash): adjustable to 100ms (default), 250ms or 600ms

Pause length: 3 seconds

Dialling type: Tone (DTMF, dual tone multi-frequency) or Pulse (loop disconnect).

Network connection: This equipment is intended to be used in the UK only.
Operation on other countries' PSTN termination points cannot be guaranteed.

Binatone Telecom plc operates a policy of continuous improvement, and so
reserves the right to make changes to the products and functions without notice.