Bimba ITM-23Q-M12 User Manual

Quick Start Guide

ITM-23Q-M12 IntelliMotor® Quick Start Guide

Requirements

To begin, make sure you have the following equipment:

• Bimba M12 cabled connectors CBL-PWR-M12- , CBL-IO-M12- , and CBL-EIP-M12-

• A personal computer running Microsoft Windows 98, 2000, ME, NT, XP, Vista,7 (32 and 64 bit), or 8.

• IQ® stepper software (available at www.bimba.com).

• For more detailed information, please download and read the ITM-23Q Hardware Manual available at www.bimba.com and refer

to section for ITM-23Q-M12

Step 1

Wire the IntelliMotor® to the 24 vdc or 48 vdc DC power source. Pin 1 (brown)
and Pin 3 (blue) connect to “V+” and Pin 2 (white) and Pin 4 connect to “V-” of
your power supply. (Do not apply power until all connections to the drive

have been made.)

Note, the ITM-23Q accepts DC voltages from 24-48 Vdc.
(Recommended power supply: Bimba P/N PWR-150A24 or PWR-320A48)

How to connect:

a) Connect the CBL-IO-M12- cable to the M12 connector marked

“I/O” on the IntelliMotor®. This is an A-coded female connector.

b) Connect the CBL-PWR-M12- cable to the M12 connector marked

“Power” on the IntelliMotor®. This is an A-coded male connector.

c) Connect the CBL-EIP-M12- cable to the M12 connector marked

“Ethernet/IP” on the IntelliMotor®. This is a D-coded female connector.

For help wiring the I/O connections, please refer to the Bimba ITM-23Q
User Manual. The wire color and signal definition for each terminal of all
three connectors are shown here.

If using an external fuse, we recommend the following:
ITM-23Q: 3AG, 4 amp (Littlefuse 313004P)

Step 2

See Bimba ITM-23Q Hardware Manual for more information about
power supply and fuse selection.

MATING CABLE

CBL-PWR-M12-

MATING CABLE

CBL-IO-M12-

MATING CABLE

CBL-EIP-M12-

ITM-23Q-2-EIP-E-M12

CONTENTS

Step 2

a) Download and install the IQ® stepper software.

b) Launch the software by clicking:

Start / All Programs / Bimba / IQ® stepper

c) Select the Ethernet port using the drop down list.

d) Connect the drive to your PC using the RJ-45 end of your CBL-EIP-M12- cable.

Step 3

a) Apply power to the drive. The drive model and rmware revision should

be automatically displayed. If they are not, check that the Ethernet box
is checked and the correct Ethernet drive IP address is displayed in the
drop down box. Change to correct drive IP address if needed.

b) Follow the conguration instructions in the IQ® stepper help screens.

The IQ® stepper software can be used to set up your drive to operate in
several different modes including: Pulse & Direction, Analog Velocity,
IQ® Programmer, and SCL.

c) IQ® stepper includes a self test option (under the Drive menu) to

verify that the ITM and power supply are correctly wired and congured.

For complete information, refer to Bimba IntelliMotor® ITM-23Q Hardware Manual. If you have any questions or com­ments, please call Bimba Customer Support: 800.442.4622, or visit us online at www.bimba.com.

Bimba Manufacturing Company

P.O. Box 68 Monee, Illinois 60449-0068

Phone: [phone] Toll Free: 800-44-BIMBA Fax: [phone]

Email: [e-mail] www.bimba.com

Form QSG-ITM-23Q-M12

Ver. 1.0.1