Billion BiPAC 7001 User Manual

BiPAC 7001

ADSL USB Modem

User’s Manual

Chapter 1 ................................................................................................1

1.1 Introducing the BiPAC 7001................................................... 1

1.2 Features of the BiPAC 7001..................................................1

1.3 Installing Billion ADSL USB Modem.......................................2

Chapter 2 ................................................................................................3

2.1 Important note for using the BiPAC 7001...............................3

2.2 Package Contents ................................................................. 3

2.3 The Front LEDs ..................................................................... 4

2.4 The Rear Ports ...................................................................... 4

2.5 Cabling ..................................................................................5

Chapter 3 ................................................................................................6

3.1 Installing the USB Driver on PC............................................. 6

3.1.1 For Windows.......................................................................6

3.1.2 For MAC OS 9/X： ...........................................................10

3.1.3 For Linux:.......................................................................... 13

3.2 Configuring the Network Properties--- LAN Adapter............ 14

3.3 Configuring the Network Properties--- WAN Adapter...........25

3.4 Information from your ISP....................................................39

Chapter 4 ..............................................................................................40

4.1 Accessing communication settings......................................40

4.2 Windows DSL Status Application......................................... 42

4.3 MAC OS 9.x Control Panel Application................................ 44

4.4 MAC OS X Control Panel Application..................................49

Chapter 5 ..............................................................................................54

5.1 Uninstall Windows: .............................................................. 54

5.2 Uninstall MAC OS:...............................................................57

5.3 Uninstall Linux: .................................................................... 59

Chapter 1

Introduction the BiPAC 7001

1.1 Introducing the BiPAC 7001

Billion’s BiPAC 7001 complies with ADSL standards and supports downstream rate of up to 8Mbps. With its user-friendly installation utility and plug-and-play USB interface, it can be easily installed on a desktop PC or notebook PC without opening the case of the computer or adding any network interface card (NIC). Users can enjoy ADSL services and broadband multimedia applications such as interactive gaming, video streaming and real-time audio much easier and faster than ever before.

1.2 Features of the BiPAC 7001

Compliant with Universal Serial Bus Specification Revision v1.1 USB bus-powered; no external power supply is required. Compatible with T1.413 i2, G.DMT, and G.lite compliant CO DSLAM equipment Provides an RJ-11 connector for connection to the telephone line Hot Plug and Play for Microsoft Windows 98 (SE), 2000, Me, and XP Supports NDIS interface for RAS and Dial-Up Networking Support for PPP over Ethernet (PPPoE) Software upgradable. Supports downstream data rates up to 8Mbps and upstream data rates up to 1024 kbps

1.3 Installing Billion ADSL USB Modem

Chapter 2

Installing the BiPAC 7001

2.1 Important note for using the BiPAC 7001

 Do not use the BiPAC 7001 in high humidity or high

temperatures.

 Avoid using this product and all accessories outdoors.  Place the BiPAC 7001 on a stable surface.

13 . Place the

ttention

2.2 Package Contents

BiPAC 7001 ADSL USB Modem

One installation CD with drivers and online manual

RJ-11 ADSL/telephone Cable (1.8M)

One USB Cable (1.5M) This Quick Start Guide

2.3 The Front LEDs

2.4 The Rear Ports

Port Meaning

USB

Connect the supplied USB cable to this port when connecting to

the PC

LINE

Connect the supplied RJ-1 1 (“telephone”) cable to this port when

connecting to the ADSL/telephone network.

LED Meaning

1 ADSL : Lit when successfully connected to an ADSL DSLAM (“linesync”)

2 DATA:

When this LED is flashing constantly, it indicates the Modem is

transmitting/receiving data

3 USB: Lit when the USB port is connected to the PC and working properly

2.5 Cabling

Through USB Port

The product can be used as a Network Adapter on your PC. That means you do not have to install a network adapter first on your PC before connecting the ADSL Modem/Router. Just connect the supplied USB cable to the USB port of the ADSL USB Modem and connect the other end to the PC. Make sure that your ADSL USB Modem and PC are turned on. On the front of the product is a bank of LEDs. As a first check, please verify that the ADSL, DA TA and USB SYN LEDs are lit. So long as the cables are connected and the LEDs are lit normally, follow section “Installing the USB Driver” below to setup this device.

 Since the product cannot auto-detect whether your cable is

correct or not, please make sure you are using the right cable to a PC or a Hub..

Chapter 3

Basic Installation

3.1 Installing the USB Driver on PC

3.1.1 For Windows

1. Insert the CD into your computer’s CD Rom drive. This is the hi-speed modem installation CD, Click “setup. exe” to continue.”.

1. Simply follow the instructions below which outline what you need to do. This section is described based on Windows XP/ 2000/Me/98, MAC OS 9/X and all systems will automatically acknowledge the modem has been connected to your computer.

2. Do not plug USB cable into ADSL USB Modem before to install the USB Driver.

2. Choose service provider from the list below and then click “Next” to continue.

3. Then click “Next”.

4. Please plug USB cable into ADSL USB Modem.

5. Select “Yes, reboot the computer now”, than close the windows.

6. After restart the PC, window will show congratulation message and user can enjoying Internet.

7. After Billion ADSL USB Modem driver is successfully installed, you will see these 2 icons on your desktop.

3.1.2 For MAC OS 9/X：

1. St art Windows. Then insert the installation CD into the CD-ROM drive. In next window , click the driver installer.

2. The “Welcome” screen will appear, then, click “Next”.

3. Input the user name and password of your Mac system.

4. The “License Agreement” screen will appear, then click “Accept”.

5. To click the type of setup you prefer, then click Next >.

6. When all necessary files have been copied, select “Restart now”, than close the windows.

3.1.3 For Linux:

For Linux installation instructions, please refer to the text file provided with your Linux driver’s package.

This driver supports Linux-2.4 kernels. The Linux kernel sources can be download from: http://www.kernel.org/pub/linux/kernel/v2.4/ The driver supports Linux-2.4 kernels.

The installed system should already have the kernel sources installed in the /usr/src/linux directory . If they are not there, try to get them of f the inst allation disks for your distribution, or download the latest Linux-2.4 kernel, and configure and build that. One common problem while compiling modules on a new kernel is not to create link /usr/src/linux which should point to the relevent kernel source directory . On a freshly installed system this link might not be present and needs to be created before the kernel or any driver module can be compiled. There are lots of books and documents available describing how to extract, configure and build the kernel from it's sources.

The driver is compiled and tested for:

RedHat 7.1 : kernels 2.4.2-2 using gcc 2.96 RedHat 8.0 : kernel 2.4.18-14 using gcc 3.2 RedHat 9.0 : kernel 2.4.20-8 using gcc 3.2

3.2 Configuring the Network Properties--- LAN Adapter

3.2.1 Configuring PC in Windows XP

1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections, and Double-click Local Area Connection.

2. In the Local Area Connection Status window, click Properties.

3. Select Internet Protocol (TCP/IP) and click Properties

4. Use the “Internet Protocol (TCP/IP) Properties” window to modify the IP address and DNS Server address as follow.

Change the IP address to a user defined address by selecting Use the following IP

address and typing the address in the space provided.

Change the DNS Server address to user defined addresses by selecting Use the

following DNS server address and typing the addresses in the spaces provided.

The “Advanced” button of the “Internet Protocol (TCP/IP) Properties” window may be

used to alter DNS addresses, WINS addresses and IP security settings.

5. Click OK from the Internet Protocol (TCP/IP) Properties window. Then, the Local Area Connection Properties window will reappear. Click OK to end configuring the network properties on your PC.

3.2.2 Configuring PC in Windows 2000

1. Go to Start / Control Panel (in Classic View). In the Control Panel, double-click on Network Connections and Double-click Local Area Connection.

2. In the Local Area Connection Status window click Properties.

+ 42 hidden pages

Billion BiPAC 7001 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual