Page 1
BiPAC 6300NX(L)
Fibre/4G LTE/Cable Gigabit
Wireless-N (VPN) Broadband
Router
Quick Start Guide
Page 2
Quick Start Guide
Page 3
Billion BiPAC 6300NX(L) Fibre/4G LTE/Cable Gigabit Wireless-N (VPN) Broadband Router
-1-
Package Contents
Billion BiPAC 6300NX(L)
Fibre/4G LTE/Cable Gigabit Wireless-N (VPN) Broadband Router
CD containing the on-line manual
Ethernet (RJ-45) cable
Two detachable antennas
Power adapter
This Quick Start Guide
Warning
PLEASE READ THE QUICK START GUIDE AND FOLLOW THE
STEPS CAREFULLY. THIS QUICK START GUIDE WILL HELP YOU
INSTALL THE DEVICE PROPERLY AND AVOID IMPROPER USAGE.
IF YOU NEED MORE INFORMATION ON THIS SOFTWARE
CONFIGURATION, PLEASE REFER TO THE USER MANUAL ON
CD-ROM.
Do not use the
router
in high humidity or high temperatu
res.
Do not use the same power source for the router as other
equipment.
Do not open or repair the case yourself. If the router is too hot,
turn off the power immediately and have it repaired at a qualified
service center.
Avoid using this
product
and all
accessories
outdoors.
Place the router on a stable surface.
Only use the power adapter that comes with the package. Using a
different voltage rating power adaptor may damage the router.
Attention
Page 4
Quick Start Guide
-2-
Hardware Overview
The Front LEDs
The Rear Ports
*
Note 1. For advanced reset and restore setting, please refer to user manual.
.2. For WPS configuration, please refer to the WPS section of user manual.
Connect the sup
plied
power adapter to this
jack.
Connect the
detachable antenna
When the system is ready,
the LED will be lit green;
lit red when the device
fails to boot.
Connect the USB cable to
this port for storage service
and 3G/ 4G LTE USB modem
backup for Internet access.
Lit Green when connected
to an Ethernet device for
1000Mbps. Lit Orange for
10/100Mbps.
Lit green when the wirel
ess
connection is established.
Flashes when sending /
receiving data.
Power
ON/OF
Push WPS button t
o
trigger Wi-Fi
Protected Setup.
*
2
Lit green when the
router is connected
to a 3G modem or
USB device.
Lit
green when
transmission speed
hitting 1000Mbps; lit
orange for 10/100Mbps.
Lit green when IP connected
and IP traffic is passing. Lit
red when IP connected failed.
Lit off when device in bridged
mode.
P
ress
the “Reset
”
button
6
seconds or above to restore
factory default settings
.*1
Connect your computer
to a LAN port with the
Ethernet cable included.
Flash green when WPS configuration
is in progress; lit up brightly and then
goes off in 5 seconds when WPS is
established; flash for 2 mins and then
goes off when WPS establishment
failure.
Gigabit Ethernet WAN
port
for connecting to Cable
Modem, Fiber Modem or PON
optic lines with RJ-45 cable.
Page 5
Billion BiPAC 6300NX(L) Fibre/4G LTE/Cable Gigabit Wireless-N (VPN) Broadband Router
-3-
Hardware Connection
3G/ 4G LTE Router Model
Broadband Router Model
Page 6
Quick Start Guide
-4-
Hardware Installation
1. Power Connection
Plug the supplied power adapter to the wall jack and the other side to the router.
Please note that the plug type may differ according to different countries.
2. LAN Connection
Connect the supplied RJ-45 Ethernet cable to one of the Ethernet ports, and the
other side to the PC’s Ethernet interface.
3. USB Connection
(1) The USB 2.0 port supports 3G/ 4G LTE modem connectivity: users can
conveniently access Internet via 3G/,4G LTE eliminating the limitations of the
wired network. This solution also employs an auto fail-over feature to ensure
always-on connectivity for SOHO users.
Page 7
Billion BiPAC 6300NX(L) Fibre/4G LTE/Cable Gigabit Wireless-N (VPN) Broadband Router
-5-
(2) Storage feature through USB 2.0 port: FTP server, SAMBA server.
4. EWAN Connection
Connect RJ-45 Ethernet cable to the EWAN port,
and connect the other side to
another alternative broadband device, such as Cable Modem, VDSL, Fibre
Modem or PON optic lines.(Please refer to User Manual for detail instruction.)
Connecting to the Router
1. Open the web browser and type http://192.168.1.254 in the browser's address box. This
number is the default IP address for this router. Press Enter.
2. A username and password window will appear. The default username is “admin
”,
password is “admin
”. Press OK to proceed.
3. You will get a status report web page and main menu screen.
Please see the relevant sections of user manual for detailed instructions on how to
configure your router.
Troubleshooting
1. None of the LEDs are on when you turn on the router.
Check the connection between the adapter and the router. If the error persists, you may have
a hardware problem. In this case you should contact technical support.
2. Can’t ping any PCs on the LAN.
Check the Ethernet LEDs on the front panel. The LED should be on for a port that has a PC
connected. If it is off, check the cables between your router and the PC. Make sure you have
uninstalled any software firewall for troubleshooting. Verify that the IP address and the subnet
mask are consistent between the router and the workstations.
Page 8
Quick Start Guide
-6-
Product Support and Contact Information
Most problems can be solved by referring to the Troubleshooting section in the User Manual. If
you cannot resolve the problem with the Troubleshooting chapter, please contact the dealer
where you purchased this product.
Contact Billion
WORLDWIDE
http://www.billion.com
BiPAC 6300NX(L) V1.00EN
Loading...