Page 1
D
KH700
700 W
Operating
and safety instructions
UK
Page 2
1Device description ....................................................................................4
2 Purpose ....................................................................................................4
3Technical data............................................................................................4
4Safety instructions ....................................................................................4
5Start-up......................................................................................................5
6Assembling the food processor ................................................................6
7Working with the mixing bowl ..................................................................7
7.1 Working with the cutting blade..........................................................7
7.2 Working with the cutting and gratings discs......................................8
7.3 Working with the kneading blade ......................................................9
8Working with the blender ..........................................................................9
9Cleaning ..................................................................................................10
10 Malfunctioning ........................................................................................11
11 Warranty, Repair & Customer Service ....................................................11
12 Disposal ..................................................................................................11
13 Table ........................................................................................................12
4 3
Page 3
Universal food processor
Bifinett KH 700
Keep these instructions for questions later on and also hand them over when
passing the device on to third parties!
1 Device description
1. Splash protection cap
2. Blender lid
3. Blender jug max. 1.5l
4. Motor block cover
5. Motor block
6. Speed controller
7. Drive shaft
8. Mixing bowl max. 1.5l
9. Lid for mixing bowl
10. Filling shaft
11. Pusher
12. Measuring cup
2 Purpose
This device is intended for the processing of
foodstuff in household quantities and only for
private use in closed rooms protected from
rain. This device is not intended for commercial or industrial use or for operation in the
open.
3 Technical data
Voltage: ................................................230 V
Power consumption: ......................700 Watt
Capacity blender jug: ............................1,5 l
Capacity mixing bowl: ..........................1,5 l
13. Retainer
14. Kneading blade
15. Blade
16. Protective case for blade
17. Potato slurry disc
18. Fine slicer
19. Coarse slicer
20. Coarse shredder
21. Fine shredder
22. French fry cutter
23. Disc holder
24. Spatula
4 Safety instructions
• Read all instructions.
• Ensure that the power cord never gets
wet or moist during operation. Route the
cable so that it cannot be pinched or otherwise damaged. Do not leave it dangling
from the working surface. Should the
power cord or the power plug be damaged, have them replaced by the Service
before using the device again.
• Pull the plug from the socket when you
do not use the device, before changing
the attachments and before cleaning the
device. Merely switching off is not sufficient since mains power is still connected
to the device for as long as the power
plug is inserted in the socket. In this way
you will also prevent inadvertent switching
on of the device.
• Do not allow children and frail persons to
handle the device without supervision –
since they might not always be able to
properly judge possible dangers.
• Use only the supplied original accessories
since these have been optimised for interaction with the device. Other parts might
not be sufficiently safe either.
• Never switch on the device without there
being ingredients in the vessels.
Overheating hazard!
• The cutting edges are very sharp! Exercise
special care when inserting and removing
or cleaning the cutting blade!
• Keep hands and utensils away from moving blades or discs while processing food
to reduce the risk of severe injury to persons or damage to the food processor.
• Do not attempt to defeat the lid interlock
mechanism.
5 Start-up
• Before starting the device ensure that ...
- the device and all accessories and the
power plug and the power cord are in
perfect condition and ...
- all packaging materials have been
removed from the device.
• Prior to initial use clean all device components as described in the “Cleaning”
chapter.
• Assemble the food processor and note
that…
- the mixing bowl works only when the
cover for the motor block, the mixing
bowl and the lid for the mixing bowl
have been properly fitted and engaged.
- the blender works only when the
blender jug and the blender lid have
been correctly fitted and engaged.
- when blender jug, mixer lid, mixing bowl
and the lid of the mixing bowl have
been fitted, only the blender will work.
4 5
Page 4
6 Assembling the
food processor
Fitting the mixing bowl
• Place the cover on the
motor block and turn
anti-clockwise until it is
seated tightly.
• Fit the mixing bowl.
Hold the bowl by the
handle and turn clockwise until it engages
with a “click”.
Fitting the lid
Note: Always ensure that the lid is properly
engaged before switching on the
device!
• Fit the lid on the mixing
bowl so that the recesses of the lid match the
slots of the bowl.
• Turn the lid clockwise
until it engages with a
“click”. The marks on
the lid and the bowl
must match. The lug of
the lid now rests on the
handle of the bowl.
Fitting the filling shaft and pusher
Caution: Never use your fingers, spatula,
spoon handles or similar objects
for pushing foodstuff through the
filling shaft!
• You can add liquid and
solid food to the mixing
bowl through the filling
shaft. Use the pusher to
close-up the filling shaft
during operation to
avoid splashing or dust
from escaping (e.g.
when processing flour).
• Use the pusher to force
foodstuff through the filling shaft.
• The pusher is equipped
with a measuring cup. If
you remove it you can
reduce size of the filling
shaft. This can be useful
when cutting or grating
relative small food.
7 Working with the mixing bowl
The supplied accessories for the mixing bowl
consist of 6 grating and cutting discs, a
kneading blade and a chopping blade for versatile use of the mixing bowl: Grating or cutting, mixing or cutting, kneading or stirring.
7.1 Working with the cutting blade
Caution:
The cutting edges are very sharp! Exercise
special care when inserting and removing or
cleaning the cutting blade!
The bowl must first be properly locked in
position before inserting the cutting blade.
Risk of injury!
Never use your fingers, spatula, spoon handles or similar objects for pushing foodstuff
through the filling shaft!
The cutting blade can be use to mix, chop or
kneading dough. For instance for chopping
meat, cheese, onions, herbs and nuts.
• Remove the cutting
blade from the protective case.
• Fit the mixing bowl to
the food processor.
• Fit the cutting blade on
the retainer and place
the latter on the drive
shaft.
• Add the ingredients to
the mixing bowl. Fit the
lid to the bowl and
insert the pusher in the
filling shaft. Switch on
the device by setting
the speed controller to the speed recommended in the table. If you are uncertain
which speed should be used, use the fastest
speed (3).
Hints:
• Cut the ingredients in approximately 3 cm
large pieces before placing them in the
bowl.
• The device chops the ingredients very fast
so that you should only run it very briefly at
a time.
• Do not operate the device for longer than
30 seconds.
• Should ingredients be trapped in the bowl
or on the cutting blade:
- Switch off the device
- Remove the lid from the mixing bowl
- Remove the ingredients with a dough
scraper / spatula.
6 7
Page 5
7.2 Working with the cutting and
grating discs
Caution: The cutting edges are very sharp!
Be particularly careful when inserting and
removing or cleaning the discs!
Never use your fingers, spatula, spoon handles or similar objects for pushing foodstuff
through the filling shaft!
With the cutting and grating discs you can
quickly slice or grate ingredients. The special
chip disc allows you to quickly prepare
homemade chips. With the potato pancake
disc you can grate raw potatoes for the
dough but also grate other vegetables or fruit
finely.
• Fit the mixing bowl on
the food processor.
S• Select the appropriate
disc. Insert the disc
with the guide edge
(the side without marking) in the disc holder.
• Push the other side
(marked with two circles
at the corners) down
until the disc engages
with a “click”.
• Fit the retainer to the
drive shaft. Insert thumb
and index finger in the
holes of the disc holder
and place it on the
retainer.
• Place the lid on the
bowl.
• You can now fill ingredients through the filling
shaft.
• For cutting and grating
set the speed controller
to speed 3 (maximum
speed). Should you wish to process soft fruit
or vegetables you can also select a lower
speed. Slowly and gradually push the ingredients in the filling shaft using the pusher.
• To remove the disc from
the disc holder, remove
the disc from the disc
holder by pushing on
the marked side in an
upward direction.
Hints:
• Cut the food into pieces so that they fit
through the filling shaft.
• Fill the filling shaft evenly and do not exert
excessive pressure.
• If you wish to process large quantities of
food do it in small batches and empty the
mixing bowl in-between.
7.3 Working with the kneading
blade
With the kneading blade you can knead
bread dough and mix batter or cake mixture.
• Place the mixing bowl
on the food processor.
• Place the kneading
blade on the retainer
and fit on the drive
shaft.
• Add the ingredients to
the mixing bowl.
• Place the lid on the
bowl and the pusher in
the filling shaft. Set the
speed controller to the
speed recommended in
the Table.
Hints:
• Put liquid ingredients into the bowl last and
start mixing at low speed to avoid splashing.
• Never fill the mixing bowl above the MAX.
mark (1.5l).
• For mixing “water like” liquids only use the
speed 1 with volume less than 1 l to avoid
liquid spilling out.
8 Working with the blender
Caution
• Never switch on the blender when empty.
• Never insert the plug in the socket before
the blender jug and the blender lid have
been correctly assembled.
• Always pull the plug from the socket
before removing the blender jug.
• Do not fill ingredients hotter than 80°C in
the blender jug.
• To avoid splashing, never add more than
1.5l of liquid in the blender jug.
• Never remove the blender lid during operation.
• First remove the blender lid before removing the blender jug.
• Never run the blender continuously for
more than 3 minutes.
You can use the blender to finely puree and
mix ingredients. You can use the blender for
preparing soups, sauces, milkshakes, baby
food or process vegetables and fruit into a
puree.
• First remove the cover
for the motor block by
turning it clockwise.
98
Page 6
• Place the blender jug in
the opening and turn it
anti-clockwise until
seated tightly.
• Place the lid on the
blender jug and turn it
anti-clockwise until seated tightly.
• Fill the ingredients in the
blender jug. Cut them
into smaller pieces
beforehand if required.
• If required, insert the
splash protection cap
and turn it anti-clockwise to secure.
• Switch on the blender
by setting the speed
controller to the desired
speed.
• Then remove the blender jug by turning it
clockwise.
Hints:
• You can add your ingredients to the blender
jug through the opening in the lid during
operation. To do so, simply remove the
splash protection cap.
• If you process hot liquids, remove the
splash protection cap to allow the steam to
escape.
• Should ingredients be trapped in the
blender jug during operation, proceed as
follows:
- Switch off the device (speed controller
to speed 0) and pull the plug from the
socket
- Remove the splash protection cap and
the lid
- Remove the trapped ingredients in the
blender jug using the dough scraper.
- Ensure you do not damage the scraper
with the blade!
9 Cleaning
• Pull the plug from the socket before every
cleaning.
• Wipe the housing with a clean, moist cloth
after each use.
• You can clean the mixing bowl and the lid
in hot soapy water.
• None of the device components are suitable for use in a dishwashing machine!
Neither should you use abrasive cleaning
agents for cleaning device components.
• Clean all device components that have
come in contact with foodstuff with detergent and hot water after use.
10 Malfunctioning
• Should the food processor suddenly stop:
- This means that the device has overheated and the integrated safety cut off
has switched off the food processor.
- Pull the plug from the socket
- Set the speed controller to speed 0
- Allow the device to cool down for 15
minutes
- If the device has not cooled off completely after 15 minutes, it will not start.
Wait another 15 minutes before switching it on again.
11 Warranty, Repair & Customer
Service
This device has a 3-yearswarranty from the
date of purchase as per our standard business conditions and proper use and maintenance.
To prolong the lifespan of your food processor, follow the directions given under
„Cleaning & Maintenance“.
In case your food processor fails to function
as expected, it must be given for repairs to a
service centre authorised by the manufacturer
or a qualified technician. For this purpose,
please contact our customer service. The
address is given in the enclosed warranty
certificate.
12 Disposal
This device must not be disposed with
household waste, because it contains materials that have to be disposed separately.
Consult your city or community administrative
authorities about procedures for the environment friendly and systematic disposal of the
food processor.
• When you have finished, switch off the
blender and first remove
the lid by turning it
clockwise.
Caution
• On no account must the device be
immersed in water or other liquids! This
can cause electric shock when remaining
liquid comes in contact with live components during subsequent operation.
• Exercise special care when cleaning the
blades, the blender jug with installed
blade and the cutting discs. The blades
and cutting edges are extremely sharp!
1110
Page 7
13 Table
The following table serves as orientation help
to determine the quantities and speeds for
various ingredients.
Do not exceed the specified operating period
to avoid overheating of the device.
In addition to the 3 speeds, a short powerful
spurt of operation is available with the pulse
stage “P”. The switch does not engage in
pulse position. Hold the switch in this position or repeatedly turn it to pulse position.
Ingredients Max. Speed stage Accessories Operating
quantity period
Bread 700 gr. Flour 3 Kneading blade 60 seconds
dough (ratio flour:
water =100:60)
Apples/ 500 gr. 3 Cutting/Grating
carrots attachments
Potatoes 500 gr. 3 Chip attachment
Meat / 500 gr. 3 / P Cutting blade 30 seconds
fish
Vegetables 500 gr. 2 Cutting blade 30 seconds
Fruit 500 gr. 2 Cutting blade 15 seconds
1312
Loading...