Page 1
Parlé
Video Display Mount Kit (PMA 2000-DM)
Installation Guide
ABOUT THIS KIT
The PMA 2000-DM kit mounts a Parlé 2000 series bar to an (X- or H-type)
VESA-mounted video display.
INSTALLATION CONSIDERATIONS
• This kit can be configured so the Parlé bar is above or below the display.
In most cases, this can be done without removing the display from the
VESA mount.
• Spring tension arms hold the bar against the video display. The brackets
and arms may be reconfigured depending on the size of the display, the
type of VESA mount, and the bar's position.
• Once the bar is mounted, the arms can be angled forward/backward for
better visibility or coverage.
• To use this kit, access to either the screws holding the VESA (X- or
H-type) mount to the display, or the vertical rails or U-channel on an
H-type VESA mounting system is necessary.
• Please read the initial pages of this guide to prepare for the installation,
and determine which configuration fits your appliction.
CONFIGURATION KEY
1) PMA Kit attached to an H-style
(or X-Style) VESA mount with the
bar below the display.
2) PMA Kit attached to an X-style
(or H-Style) VESA mount with the
bar above the display.
KIT CONTENTS / DETAILS
Brackets
Pin
The pin keeps arm
extended during
installation of the bar
in an under-display
configuration.
Left Arm
Right Arm
Spring
Arm
Spring
Mechanism
Traveler Arm
Crossbar
Hardware
Qty Description
4 M8 x 25 PH Screws
4 M8 x 30 PH Screws
4 M8 x 40 PH Screws
4 M8 x 45 PH Screws
4 Spacers
2 M6 x 12
Flat Head Screws
2 M6 Nuts
2 M8 Flat Washers
2 M5 x 8 PH Screws
3) PMA Kit shown attached to an
the vertical rails of a VESA mount
with the bar under the display.
4) PMA Kit shown attached to an
the vertical rails of a VESA mount
with the bar above the display.
5) Low Prole VESA mounts -
Install spacers between VESA
mount and TV to provide space for
the kit arms. The bar can then be
mounted above or below the TV.
Note: Must be able to remove TV from
the VESA mount to install the spacers.
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA W: www.biamp.com
Page 2
PMA 2000-DM KIT FLEXIBILITY
This kit was designed to be configured in a number of
ways to mount a Parlé 2000-level bar above or below a
VESA-mounted TV or video display.
Once the bar is connected to the crossbar, it can
be moved forward or back to better align with the
TV, or with the VBC models, provide increased
camera visibility.
OR
Bar Adjustment Considerations
• To rotate the bar up or down, hold the bar on each side of the plastic lens and
apply equal rotational force with both hands.
• Don't twist the bar from the ends, rotate the bar beyond the mechanical stops or
move it side-to side while adjusting the angle.
• When extending the bar on the display mount, move it up or down slowly,
especially near its maximum extension.
PREPARATION
Remove the bar from either the table stand (1) or the wall
plate (2) before attaching to the PMA kit. Reserve the
M3 screws to attach the bar to the crossbar in the last
installation step of any configuration.
Remove Table Stand
1
Remove from Wall Plate
2
page 2 Installation Guide PMA 2000-DM
Page 3
INSTALLATION CHOICES
This guide covers several possible conguration options for installing the bar
on your video display (TV). Congurations 1, 2, 3, and 4 can be accomplished
without removing the display from the wall. For very low prole VESA mounts
(Conguration 5), you must remove the display from the wall to utilize the kit. Make a
choice below that matches your intended conguration.
Conguration 1
Mount Bar BELOW the TV using the circled VESA mounting holes (pgs 4-7).
Conguration 2
Mount Bar ABOVE the TV using the circled VESA mounting holes (pgs 8-12).
Congurations 3 and 4
Mount Bar on the VESA mount's vertical rails behind the TV.
Position Bar BELOW (pgs 14-17) or ABOVE (pgs 18-23)
3 4
Conguration 5
Mount bar to a LOW PROFILE VESA mount (pg 24), then chose either Configuration
1 or 2 depending upon the desired bar location.
NOTE: This choice necessitates removal of the TV from the VESA mount to add spacers
(circled) to provide enough area for the kit arms to t behind the TV.
PMA 2000-DM Installation Guide page 3
Page 4
CONFIGURATION 1 (Bar below the TV using the TV/VESA attachment)
Hold one Spring Arm behind the TV with the bracket level with the VESA
attachment to the TV, aligning the upper slot with that VESA attachment
screw. The Spring Arm should extend almost to, but not past the lower
edge of the display, and the Traveler Arm should extend at least 102 mm
(4") past that edge to allow for bar attachment.
• If the Spring Arm extends past the lower edge of the TV, continue
below to change the bracket position.
• If the Spring Arm is behind the TV and the Traveler Arm extends
the minimum amount, attach the arms to the TV.
• If the Spring Arm is behind the display and the Traveler Arm DOES
NOT extend the minimum amount, use mounting Configuration 3.
Change Bracket Position on Spring Arm
There are 5 positions for the bracket.
1. Determine the best position for the bracket to ensure the Spring
Arm is behind the TV.
2. From the back of the Spring Arm, unscrew the bracket, reserving
the screws for reattachment.
3. Reposition the bracket, and reattach. Fully tighten connections.
4. Repeat for the other arm. Both brackets must be at the same
position on the Spring Arms.
Default bracket position,
Spring Arm behind TV with
enough extension for bar
attachment
Bracket moved down 1 position to use
top notch (recommended), Spring Arm
is fully behind TV with Traveler Arm
extended for bar attachment.
Default bracket position,
arm attachment doesn't
hide Spring Arm behind
TV and allow bar to be
flush with the TV
1
3
2
4
page 4 Installation Guide PMA 2000-DM
Page 5
CONFIGURATION 1 (continued - Bar below the TV using the TV/VESA attachment)
Attach arms at the lower TV/VESA mounting points
If feasible, pull the display away from the wall for easier access to the mounting
screws. If it can't be pulled away, use a short or 90° ratcheting screwdriver from the
front or side to access the screws securing the mount to the display.
Note: Mount the arms to the outside of the VESA mount for increased stability. If connectors
or power cords interfere, the arms may be mounted to the inside.
1. Loosen the lower VESA screws (circled) 3mm (.12"). If the (M8) VESA
mounting screws aren't long enough to stay threaded in the TV, replace them
one at a time with the included 25 or 30mm M8 screws.
2. Slide the bracket between the TV and the VESA mount the full length of the
notch. The upper bracket notch is preferred, but both arms must hang at the
same level.
3. Arms should hang parallel. Snug tighten the circled screws to hold the arms in
place.
Kit parts
Congured arms x2
Optional hardware
M8 x 30
PH Screw
Substitute for existing VESA
bolts that are too short
to accommodate the arm
brackets
M8 x 25
PH Screw
1
2
3
PMA 2000-DM Installation Guide page 5
Page 6
CONFIGURATION 1 (continued - Bar below the TV using the TV/VESA attachment)
Crossbar Attachment
1. Fit the crossbar into the small notches in the Traveler
Arms (as shown). Center and loosely screw the crossbar
to each arm.
2. With the arms parallel to each other and the crossbar
parallel to the edge of the display, fully tighten the screws
holding the arms to the TV (circles).
3. Center the crossbar and tighten the screws holding it to
the arms (arrows).
1
Kit parts
• Crossbar x1
• (M5 Screws) x2
M5 x 8
PH Screw
•
Crossbar attached
to arms
2
3
page 6 Installation Guide PMA 2000-DM
Page 7
CONFIGURATION 1 (continued - Bar below the TV using the TV/VESA attachment)
Bar Attachment to PMA 2000-DM
1. Fold the hinge brackets up and hang the bar on the
crossbar knobs.
2. Secure with an M3 screw on each bracket (circled).
3. Rotate the bar back up. See adjustment notes at right.
4. Remove the pins holding the arms in the extended
position. The pins can be discarded.
5. Move the bar forward or back for best directionality, and
push it up against the display.
6. Installation is complete.
1
2
M3 Screws
Hardware
• M3 Screws x2
From Parlé bar
table stand or plate
removal
Bar Adjustment
• When rotating the bar
up and down, grasp the
center with 2 hands close
to the plastic lens and
rotate with equal force.
• Don't twist the bar from
the ends, rotate the bar
beyond the mechanical
stops, or move it side-to
side while adjusting the
angle.
• When extending the
bar, move it up or down
slowly, especially near its
maximum extension.
3
4
Pin
5
6
PMA 2000-DM Installation Guide page 7
Page 8
CONFIGURATION 2 (Bar above the TV using the TV/VESA attachment)
Change arm conguration
The arms ship congured for below-the-screen mounting. The arms need to be
reconfigured to preserve the tension spring action function when mounted above
the TV. To do this, the lower portion of each arm (Traveler Arm) must be removed,
flipped, and reattached to the opposite Spring Arm.
1. Place the arms side by side as shown.
2. Remove the pins holding the Traveler Arms extended. Move the Traveler
Arms up if the spring doesn't pull it up automatically. Pins can be discarded.
3. Remove screws holding each Traveler Arm (front and back). Reserve for
reattachment.
4. Slide each Traveler Arm up to remove it.
1 2
3
page 8 Installation Guide PMA 2000-DM
4
Page 9
CONFIGURATION 2 (continued - Bar above the TV using the TV/VESA attachment)
Change arm conguration (continued)
5. Turn each arm 180° and place next to the opposite Spring Arm as shown.
6. Side each carriage up into the Spring Arm
7. Reinstall screws on both sides to secure.
5
6
7
PMA 2000-DM Installation Guide page 9
Page 10
CONFIGURATION 2 (continued - Bar above the TV using the TV/VESA attachment)
Hold one Spring Arm behind the TV with the bracket level with the VESA
attachment to the TV, aligning the upper slot with that VESA attachment
screw. The Spring Arm should extend almost to, but not past the upper
edge of the display, and the Traveler Arm should extend at least 102 mm
(4") above that edge to allow for bar attachment.
• If the Spring Arm extends past the upper edge of the TV, continue
below to change the bracket position.
• If the Spring Arm is behind the TV and the Traveler Arm extends
the minimum amount, attach the arms to the TV.
• If the Spring Arm is behind the display and the Traveler Arm DOES
NOT extend the minimum amount, use mounting Configuration 4.
Change Bracket Position on Spring Arm
There are 5 positions for the bracket.
1. Determine the best position for the bracket to ensure
the Spring Arm is behind the TV.
2. From the back of the Spring Arm, unscrew the
bracket, reserving the screws for reattachment.
3. Reposition the bracket, and reattach. Fully tighten
both connections.
4. Repeat for the other arm. Both brackets must be at
the same position on the Spring Arms.
Red arrow indicates VESA connection to the display
Bracket repositioned
to keep Spring Arm
behind TV with enough
extension for bar
attachment
Default bracket position,
not enough room for bar
attachment
Bracket moved
down on Spring Arm
to keep it behind
display with Traveler
Arm extended for
bar attachment.
1
2
Position bracket on arm
(5) places available
3 4
page 10 Installation Guide PMA 2000-DM
Page 11
CONFIGURATION 2 (continued - Bar above the TV using the TV/VESA attachment)
Attach arms at the upper TV/VESA mounting points
If feasible, pull the display away from the wall for easier access to the mounting
screws. If it can't be pulled away, use a short or 90° ratcheting screwdriver from
the front or side to access the screws securing the mount to the display.
Note: Mount the arms to the outside of the VESA mount for increased stability. If
connectors or power cords interfere, the arms may be mounted to the inside.
1. Loosen the lower screws (circled) in the VESA mount 3 mm (.12"). If the
(M8) VESA mounting screws aren't long enough to stay threaded in the TV,
replace them with the included 25 or 30 mm M8 screws.
2. Slide the bracket between the TV and the VESA mount the full length of the
notch. The upper bracket notch is preferred, but both arms must be at the
same level.
3. Arms should stand up and be parallel. Snug tighten the circled screws to
hold the arms in place.
Kit parts
Congured arms x2
Optional hardware
M8 x 30
PH Screw
Substitute for existing
VESA bolts that are too
short to accommodate
the arm brackets
M8 x 25
PH Screw
1
2
3
PMA 2000-DM Installation Guide page 11
Page 12
CONFIGURATION 2 (continued - Bar above the TV using the TV/VESA attachment)
Crossbar Attachment
1. Fit the crossbar into the small notches in the Traveler
Arms (as shown). Center and loosely screw the crossbar
to each arm.
2. With the arms parallel to each other and the crossbar
parallel with the edge of the display, fully tighten the
screws holding the arms to the TV (circles).
3. Center the crossbar and tighten the screws holding it to
the arms (arrows).
1
Kit parts
• Crossbar x1
• (M5 Screws) x2
M5 x 8
PH Screw
•
Crossbar attached
to arms
3
2
page 12 Installation Guide PMA 2000-DM
Page 13
CONFIGURATION 2 (continued - Bar above the TV using the TV/VESA attachment)
Bar Attachment to PMA 2000-DM
1. Fold the hinge brackets up and hang the bar on the
crossbar knobs.
2. Secure with an M3 screw on each bracket (circled).
3. Rotate the bar up. See adjustment notes at right.
4. Grasp the bar and crossbar in the middle. Move it forward
or back for best directionality, and push it down against
the display.
5. Installation is complete.
1
2
3
4
Hardware
• M3 Screws x2
From Parlé bar table
stand or wall plate
removal
M3 Screws
Bar Adjustment
• When rotating the bar
up and down, grasp the
center with 2 hands close
to the plastic lens and
rotate with equal force.
• Don't twist the bar from
the ends, rotate the bar
beyond the mechanical
stops, or move it side-to
side while adjusting the
angle.
• When extending the
bar, move it up or down
slowly, especially near its
maximum extension.
5
PMA 2000-DM Installation Guide page 13
Page 14
CONFIGURATION 3 (Bar below the TV - Kit connection to VESA vertical rails)
Attachment to the vertical rails is suggested either for ease of installation
access, or when the VESA-display attachment points are too far away
from the edge of the display for the Traveler Arms to extend past the
edge. Use the M6 nuts, M6 bolts and M8 washers shown on the next
page to attach the congured arms to the rails.
Hold one Spring Arm behind the TV with the bracket aligning with the
expected attachment to the vertical rails. The Spring Arm should extend
almost to, but not past the edge of the display, and the Traveler Arm
should extend at least 102 mm (4") beyond that edge to allow for bar
attachment.
• If the Spring Arm extends past the edge of the TV, continue below
to change the bracket position.
• If the Spring Arm is behind the TV and the Traveler Arm extends the
minimum amount, attach the arms to the rails.
Change Bracket Position on Spring Arm
There are 5 positions for the bracket.
1. Determine the best position for the
bracket.
2. From the back of the Spring Arm,
unscrew the bracket, reserving the
screws for reattachment.
3. Reposition the bracket, and
reattach. Fully tighten both
connections.
4. Repeat for the other arm. Both
brackets must be at the same
position on the Spring Arms.
1
Default bracket position,
Spring Arm behind TV
with enough extension
for bar attachment
Red arrow indicates VESA connection to the display
2
Default bracket position, arm
attachment doesn't fully hide
the Spring Arm behind the TV
and allow bar to be ush with
the TV
Bracket moved
down, Spring Arm
fully behind display
with Traveler Arm
extended for bar
attachment.
3
4
page 14 Installation Guide PMA 2000-DM
Page 15
CONFIGURATION 3 (continued - Bar below the TV / Kit connection to vertical rails)
Arm Attachment to VESA Vertical Rails
Use the hardware noted at right to attach the congured arms to the rails.
1. Position each bracket against the at side of the rail (between the rail and
the display). The nut and at washer will sit inside the rail channel. The arms
can be positioned either to the outside (recommended) or inside of the rails,
and must be at the same height. The Spring Arm portion of the arm must be
fully behind the TV.
2. Insert each screw into the upper notch in the bracket, through the rail, then
secure with the at washer and nut as shown.
3. Ensure the arms are hanging parallel with the VESA rails, and tighten the
circled connections.
Kit parts
• Congured arms x2
Hardware
• M6 x 12 Flat Head Screws x2
• M6 Nuts x2
• M8 Flat Washers x2
VESA to TV
connection
21
M6 Nut
M8 Flat
Washer
M6 x 12
Flat Head Screw
M6 x 12
Flat Head
Screw
M6 Nut M8 Flat
Washer
3
PMA 2000-DM Installation Guide page 15
Page 16
CONFIGURATION 3 (continued - Bar below the TV / Kit connection to vertical rails)
Crossbar Attachment
1. Fit the crossbar into the small notches in the Traveler
Arms (as shown). Center and loosely screw the crossbar
to each arm.
2. With the arms parallel to each other and the crossbar
parallel to the edge of the display, fully tighten the screws
holding the arms to the TV (circles).
3. Center the crossbar and tighten the screws holding it to
the arms (arrows).
1
Kit parts
• Crossbar x1
• (M5 Screws) x2
M5 x 8
PH Screw
•
Crossbar attached
to arms
2
3
page 16 Installation Guide PMA 2000-DM
Page 17
CONFIGURATION 3 (continued - Bar below the TV / Kit connection to vertical rails)
Bar Attachment
1. Fold the hinge brackets up and hang the bar on the
crossbar knobs.
2. Pull the bar down slightly to capture the knobs, and
secure with an M3 screw on each bracket (circled).
3. Rotate the bar up. See adjustment notes below right.
4. Remove the pins holding the arms in the extended
position. The pins can be discarded.
5. Grasp the bar/crossbar in the middle to move it forward or
backward to better align with the audience. Push the bar
up against the display. Installation is complete.
1
2
M3 Screws
Hardware
• M3 Screws x2
• From Parlé bar
stand or plate
removal
3
4
Pin
• When rotating the bar up and down,
grasp the center with 2 hands close to
the plastic lens and rotate with equal
force.
• Don't twist the bar from the ends, rotate
the bar beyond the mechanical stops,
or move it side-to side while adjusting
the angle.
• When extending the bar, move it up
or down slowly, especially near its
maximum extension.
Bar Adjustment
5
PMA 2000-DM Installation Guide page 17
Page 18
CONFIGURATION 4 (Bar above the TV / Kit connection to vertical rails)
Change arm conguration
The arms ship congured for below-the-screen mounting. The arms need to be
reconfigured to preserve the tension spring action function when mounted above
the TV. To do this, the lower portion of each arm (Traveler Arm) must be removed,
flipped, and reattached to the opposite Spring Arm.
1. Place the arms side by side as shown.
2. Remove the pins holding the Traveler Arms extended. Move the Traveler
Arms up if the spring doesn't pull it up automatically. Pins can be discarded.
3. Remove screws holding each Traveler Arm (front and back). Reserve for
reattachment.
4. Slide each Traveler Arm up to remove it.
1 2
3
page 18 Installation Guide PMA 2000-DM
4
Page 19
CONFIGURATION 4 (continued - Bar above the TV / Kit connection to vertical rails)
Change arm conguration (continued)
5. Turn each arm 180° and place next to the opposite Spring Arm as shown.
6. Side each carriage up into the Spring Arm
7. Reinstall screws on both sides to secure.
5
6
7
PMA 2000-DM Installation Guide page 19
Page 20
CONFIGURATION 4 (continued - Bar above the TV / Kit connection to vertical rails)
Hold one Spring Arm behind the TV with the bracket level with an upper
hole on the VESA vertical rails, aligning the upper slot with that rail hole.
The Spring Arm should extend almost to, but not past the upper edge
of the display, and the Traveler Arm should extend at least 102 mm (4")
above that edge to allow for bar attachment.
• If the Spring Arm extends past the upper edge of the TV, continue
below to change the bracket position.
• If the Spring Arm is behind the TV and the Traveler Arm extends
the minimum amount, attach the arms to the TV.
Change Bracket Position on Spring Arm
There are 5 positions for the bracket.
1. Determine the best position for the bracket to ensure
the Spring Arm is behind the TV.
2. From the back of the Spring Arm, unscrew the
bracket, reserving the screws for reattachment.
3. Reposition the bracket, and reattach. Fully tighten
both connections.
4. Repeat for the other arm. Both brackets must be at
the same position on the Spring Arms.
Bracket repositioned
to keep Spring Arm
behind TV with enough
extension for bar
attachment
Red arrow indicates VESA connection to the display
Default bracket position,
not enough room for bar
attachment
Bracket moved
down on Spring Arm
to keep it behind
display with Traveler
Arm extended for
bar attachment.
1
2
Position bracket on arm
(5) places available
3 4
page 20 Installation Guide PMA 2000-DM
Page 21
CONFIGURATION 4 (continued - Bar above the TV / Kit connection to vertical rails)
Arm Attachment to VESA Vertical Rails
Use the hardware noted at right to attach the congured arms to the rails.
1. Position each bracket against the at side of the rail (between the rail and
the TV). The nut and at washer will sit inside the rail channel. The arms can
be positioned either to the outside (recommended) or inside of the rails, and
must be at the same height. The Spring Arm portion of the arm must be fully
behind the TV.
2. Insert each screw into the upper notch in the bracket, through the rail, then
secure with the at washer and nut as shown.
3. Ensure the arms are hanging parallel with the VESA rails, and tighten the
circled connections.
Kit parts
• Congured arms x2
Hardware
• M6 x 12 Flat Head Screws x2
• M6 Nuts x2
• M8 Flat Washers x2
VESA to TV
connection
21
M6 Nut
M8 Flat
Washer
M6 x 12
Flat Head Screw
M6 x 12
Flat Head
Screw
M6 Nut M8 Flat
Washer
3
PMA 2000-DM Installation Guide page 21
Page 22
CONFIGURATION 4 (continued - Bar above the TV / Kit connection to vertical rails)
Crossbar Attachment
1. Fit the crossbar into the small notches in the Traveler
Arms (as shown). Center and loosely screw the crossbar
to each arm.
2. With the arms parallel to each other and the crossbar
parallel with the edge of the display, fully tighten the
screws holding the arms to the TV (circles).
3. Center the crossbar and tighten the screws holding it to
the arms (arrows).
1
Kit parts
• Crossbar x1
• (M5 Screws) x2
M5 x 8
PH Screw
•
Crossbar attached to arms
3
2
page 22 Installation Guide PMA 2000-DM
Page 23
CONFIGURATION 4 (continued - Bar above the TV / Kit connection to vertical rails)
Bar Attachment
1. Fold the hinge brackets up and hang the bar on the crossbar
knobs.
2. Secure with an M3 screw on each bracket (circled).
3. Rotate the bar up. See adjustment notes below right.
4. Grasp the bar / crossbar in the middle to move it forward
or back for best directionality, and push it down against the
display.
5. Installation is complete.
1
2
Hardware
• M3 Screws x2
From Parlé bar table
stand or wall plate
removal
M3 Screws
3
• When rotating the bar up and down,
grasp the center with 2 hands close to
the plastic lens and rotate with equal
force.
• Don't twist the bar from the ends, rotate
the bar beyond the mechanical stops, or
move it side-to side while adjusting the
angle.
• When extending the bar, move it up
or down slowly, especially near its
maximum extension.
Bar Adjustment
4
5
PMA 2000-DM Installation Guide page 23
Page 24
CONFIGURATION 5 (Bar below the TV / Low Prole VESA mount)
Low Prole VESA mounts (Add spacers)
If there isn't enough space to accommodate the depth of the kit arms between the
TV and VESA mount, spacers need to be installed at each of the four TV-to-VESA
attachment points (circled at right). This process is also applicable with X-type low
prole VESA mounting systems. The TV must be removed from the VESA mount
rst before adding the spacers.
1. Replace the mounting screws with either the 40 or 45 mm M8 screws. Insert
each through the VESA mount (from the rear) and add a spacer to each
screw. Use the same length screw for all four connections.
2. If the screws will still be accessible after the TV is on the wall, reinstall the
TV, but leave about 3 mm (.12") space open between either the lower or
upper set of spacers and the TV (where the kit arms will be located).
Note: Depending upon the type of VESA mounting system, it may be easier to install
the arms on the appropriate screws prior to reattaching the TV to the wall. If that is
the case - follow the installation steps in either Conguration 1 or 2 until the crossbar
is loosely attached to the arms before attaching the TV and kit assembly to the wall.
Parts and Hardware
Spacers x4
M8 x 40 Screws x4 OR
M8 x 45 Screws x4
M8 x 45
PH Screw
M8 x 40
PH Screw
15mm
Spacer
Spacers
Spacer locations
21
M8 x 40 or 45
screws
page 24 Installation Guide PMA 2000-DM
Page 25
CONFIGURATION 5 (continued - Bar below the TV / Low Prole VESA mount)
3. The Parlé bar can be installed below or above the display. Follow the
appropriate instructions to install the bar.
Note: The arms should always be inserted between the spacer and the TV
(see example below)
3
VESA
mount
Spacer
TV
PMA arm
4. Install bar below the display - go to Conguration 1 (pages 4-7)
Install the bar above the display - go to Conguration 2 (pages 8-13)
Conguration 1 Conguration 2
CONTACT US
Email: support@biamp.com
Web: support.biamp.com
A: 9300 S.W. Gemini Drive Beaverton, OR 97008 USA W: www.biamp.com
Warranty: biamp.com/legal/warranty-information
Safety & Compliance: biamp.com/compliance
11SEP2023
Loading...