Berkel X13-PLUS User Manual

SLICING

MANUAL GRAVITY FEED SLICER

Model X13-PLUS

FE AT U R E S

Berkel model X13-PLUS manual gravity feed slicer offers a
number of special features. A sanitary one piece engineered
polymer base and product table reduces seams and joints
while providing an NSF approved surface for easy, effective
cleaning. A removable and submersible table mounted
sharpener with borazon stones for accurate sharpening.
Completely mechanical, gauge plate interlock. Precise
thickness control is achieved using a variable pitch barrel
cam for ne adjustment and wafer thin slices. The index knob
and operating controls are mounted outside of the drip zone
for quick and easy access. A permanent ring guard protects
the entire non-slicing portion of the knife during slicing and
cleaning. An easy to use kick stand supports the slicer for
easy access to clean under the slicer.

Item # __________________ C.S.I. Section 11420

X13 -PLU S

STANDARD FEATURES

■ 1-speed, 1⁄2 HP, permanently lubricated ball bearing knife
motor with thermal protection.

■ Furnished in 120/60/1, 7 amps, AC, with 3 wire cord and
plug.

■ LED indicates power to the slicer.

■ One-piece NSF polymer base and product table for
reduced seams, accessibility and easy cleaning.

■ Index knob conveniently located outside the drip zone in
the upper left to provide quick and easy access.

■ Variable pitch barrel cam for ultra ne, precise slice
adjustment to a thickness of 15⁄16" (34 mm).

■ 13" (330 mm) diameter, hollow ground, hardened and
polished forged stainless steel knife

■ Large product table with extra capacity:

• Rectangles up to 101⁄2" x 63⁄4" (265 mm x 170 mm)

• Squares up to 71⁄2" (190 mm)

• Rounds up to 81⁄2" (220 mm) diameter.

■ Articulating and full length rear mounted meat pusher to
secure and advance products evenly.

■ Ergonomic, multi-grip handle to advance product table.

■ Submersible, removable product table mounted sharpener
for consistent sharpening and easy cleaning.

■ Borazon sharpening stones for fast, accurate sharpening
and extended life.

■ No-volt release requires restarting the slicer after a power
interruption.

■ Permanent ring guard protects entire non-slicing portion of
the knife.

■ Sealed start/stop switches conveniently located on the
index knob housing out of the food zone.

■ Mechanical interlock for reliably securing the gauge plate
during cleaning (gauge plate interlock).

■ An easy to use kick stand for easy cleaning under the
sl i cer.

ACCESSORIES

Vegetable chute with pusher

Product fence

Slaw tray

COMPLIES WITH NSF/ANSI STANDARD #8

a divisi on of IT W Food Equ ipment Group LLC

P.O. Box 696 ■ Louisville, KY 40201 ■ Toll-free: 1-800-814-2028 ■ Local: 502-778-2791 ■ Quote & Order Fax: [phone]

BK45746 (08/16)

www.berkelequipment.com

SPECIFICATIONS

SLICING

X13 -PLU S

MANUAL GRAVITY FEED SLICER

Motor: 1-speed, 1⁄2 HP totally enclosed and permanently
lubricated ball bearings, thermally protected.

Electrical: Furnished in 120/60/1, 7 amps, AC, ETL Listed,
with a 6' long 3-wire cord and plug.

Finish/Construction: Base, product table, pusher, support
arm and upper housing are constructed of NSF approved,
engineered polymers reducing the number of seams. Gauge
plate and center plate are anodized aluminum. All controls are
sealed and located out of the drip zone.

Knife: 13" (330 mm) diameter, hollow ground, hardened and
polished stainless steel.

Knife Sharpener: Removable and submersible table
mounted, two stone, dual action design to ensure correct
pressure and contact angle are always applied, thus reducing
knife wear and delivering a perfect edge. Borazon stones last
longer, sharpen faster and clean easier.

Thickness Control: Index knob controls a precision,
variable pitch barrel cam with ultra-ne adjustment in the
rst revolution and opens to a thickness of 15⁄16" (34 mm) for
accurate and consistent slicing. This control is located out

of the drip zone on the upper left to provide quick and easy
access for operation and cleaning.

Gauge Plate Interlock: Mechanical interlock using twisted
wire, aircraft cables. Table must be in the home position and
gauge plate closed to remove table. Once table is removed,
the gauge plate can not be opened.

Cutting Capacity: Shown in chart below.
Pr o d u c t Table: Full gravity feed 45° angle with articulating

rear mounted pusher that runs the entire length of the table to
secure product for increased yield and consistency in every
slice. A fence is included for additional product stability.

Kick Stand: An easy to use kick stand supports the slicer for
easy access to clean under the slicer.

No-volt Release: Requires restarting the slicer in the event of
a power interruption.

Knife Ring Guard: Permanent tapered guard covers the
non-slicing portion of the knife edge.

Controls: Sealed push-button switches located on the index
knob housing out of the drip zone.

Warranty: Parts, labor and travel coverage for one year,
exclusive of wear items.

MODEL

NUMBER CUTTING CAPACITY

Rectangle 101⁄2" x 63⁄4" (265 x 170 mm)

X13-PLU S

Square 71⁄2" (190 mm)

Round 81⁄2" (220 mm)

SLICE

THICKNESS

15⁄16"

(34 mm)

KNIFE

DIA.

13"

(330 mm)

MODEL

NUMBER MOTOR ELECTRICAL WEIGHT

X13-PLU S

P.O. Box 696 ■ Louisville, KY 40201 ■ Toll-free: 1-800-814-2028 ■ Local: 502-778-2791 ■ Quote & Order Fax: [phone]

BK45746 (08/16)

1-speed

1

⁄2 HP

NOTE: As we continua lly stri ve to improve our pro ducts, speci cations are ne cess arily s ubjec t to change witho ut notic e.

120/60/1

7 amps

Net 88 lbs. (40 kg)

Ship 118 lbs. (54 kg)

a divisi on of IT W Food Equ ipment Group LLC

WIDTH DEPTH HEIGHT

31"

(787 mm)

PRODUCT DIMENSIONS

WIDTH DEPTH HEIGHT

28"

(710 mm)

30"

(762 mm)

(660 mm)

BOX DIMENSIONS

31"

(787 mm)

www.berkelequipment.com

31"

(787 mm)

26"