Berkel X13E User Manual
Model X13E
Features
Berkel model X13E manual gravity feed slicer offers a
number of special features. A sanitary one piece engineered polymer base and product table reduces seams
and joints while providing an NSF approved surface for
easy, effective cleaning. A removable and submersible
table mounted sharpener with borazon stones for accurate
sharpening. Precise thickness control is achieved using
a variable pitch barrel cam for ne adjustment and wafer
thin slices. The index knob and operating controls are
mounted outside of the drip zone for quick and easy
access. A permanent ring guard protects the entire nonslicing portion of the knife during slicing and cleaning.
An easy to use kick stand supports the slicer for easy
access to clean under the slicer. A fence is provided for
extra holding of small products.
Item # _________________________________________
Model X13E
Manual Gravity Feed Slicer
❑ X13E Manual Gravity Feed Slicer
Standard Features
➤ 1-speed, 1/2 HP, permanently lubricated ball bearing
knife motor with thermal protection
➤ Furnished in 120/60/1, 8 amps, AC, with 3 wire cord
and plug (see below for optional voltages)
➤ One-piece NSF approved polymer base and product
table for reduced seams, accessibility and easy
cleaning
➤ Index knob conveniently located outside the drip zone
in the upper left to provide quick and easy access
➤ Variable pitch barrel cam for ultra ne, precise slice
adjustment to a thickness of 1
➤ 13" (330 mm) diameter, hollow ground, hardened and
polished forged stainless steel knife
➤ Large product table with extra capacity:
– Rectangles up to 10
– Squares up to 7
– Rounds up to 8
➤ Articulating and full length rear mounted meat pusher
with fence to secure and advance products evenly
➤ Ergonomic, multi-grip handle to advance product table
➤ Submersible, removable product table mounted
sharpener for consistent sharpening and easy cleaning
➤ Borazon sharpening stones for fast, accurate
sharpening and extended life
➤ No-volt release requires restarting the slicer after a
power interruption
➤ Permanent ring guard protects entire non-slicing
portion of the knife
➤ LED indicates power to the slicer
➤ Sealed start /stop switches conveniently located on the
index knob housing out of the food zone
➤ An easy to use kick stand for easy cleaning under the
slicer
1
1
⁄2" (190 mm)
1
⁄2" (220 mm) diameter
Power Options
❑ 1/2 HP, 220/50/1, 3.5 amps, AC, not submitted for
ETL Listing
❑ 1/2 HP, 220/60/1, 3.5 amps, AC, not submitted for
ETL Listing
5
⁄16" (34 mm)
⁄2" x 63⁄4" (265 mm x 170 mm)
Manual Gravity Feed Slicer Model X13E
Accessories
Approved By:
Date
Berkel Company • 2006 Northwestern Parkway • PO Box 696 • Louisville, KY 40201
800-348-0251 • FAX 888-888-2838 • www.berkel.com
Form BK45707 (03-09)
❑ Vegetable Chute with Pusher
❑ Skewers with Coring Tool
❑ Slaw Tray
Model X13E
Manual Gravity Feed Slicer
Model
No.
Rect. 101⁄2" x 63⁄4" (265 x 170 mm)
X13E
Motor Electrical Weight
1-speed
1/2 HP
Cutting Capacity
Square 7
Round 8
1
⁄2" (190 mm)
1
⁄2" (220 mm)
120/60/1
8 amps
Ship 116 lb. (53 kg)
Slice
Thickness
5
⁄16"
1
(34 mm)
Net 86 lb. (39 kg)
Knife
Diameter
13"
(330 mm)
Width Depth Height
31"
(787 mm)
Width A Depth B Height C
(710 mm)
Product Dimensions
28"
(735 mm)
Box Dimensions
31"
(787 mm)
29"
25"
(635 mm)
31"
(787 mm)
Specifi cations
Motor: 1-speed, 1/2 HP totally enclosed and permanently
lubricated ball bearings, thermally protected.
Electrical: Furnished in 120/60/1, 8 amps, AC, ETL
Listed, with 3-wire cord and plug. Power options noted on
page 1.
Finish/Construction: Base, product table, pusher, support
arm and upper housing are constructed of NSF approved,
engineered polymers reducing the number of seams.
Gauge plate and center plate are anodized aluminum.
All controls are sealed and located out of the drip zone.
Knife: 13" (330 mm) diameter, hollow ground, hardened
and polished stainless steel.
Knife Sharpener: Removable and submersible table
Manual Gravity Feed Slicer Model X13E
mounted, two stone, dual action design to ensure correct
pressure and contact angle are always applied, thus
reducing knife wear and delivering a perfect edge. Borazon
stones last longer, sharpen faster and clean easier.
Thickness Control: Index knob controls a precision,
variable pitch barrel cam with ultra- ne adjustment in the
rst revolution and opens to a thickness of 1
As we continually strive to improve our products, speci cations are necessarily subject to change without notice.
5
⁄16" (34 mm)
Berkel Company • 2006 Northwestern Parkway • PO Box 696 • Louisville, KY 40201
800-348-0251 • FAX 888-888-2838 • www.berkel.com
Form BK45707 (03-09)
for accurate and consistent slicing. This control is located
out of the drip zone on the upper left to provide quick and
easy access for operation and cleaning.
Cutting Capacity: Shown in chart above.
Product Table: Full gravity feed 45° angle with articulating
rear mounted pusher that runs the entire length of
the table to secure product for increased yield and
consistency in every slice. A fence is provided for holding
small products.
Kick Stand: An easy to use kick stand supports the slicer
for easy access to clean under the slicer.
No-volt Release: Requires restarting the slicer in the
event of a power interruption.
Knife Ring Guard: Permanent tapered guard covers the
non-slicing portion of the knife edge.
Controls: Sealed push-button switches located on the
index knob housing out of the drip zone.
Warranty: Parts, labor and travel coverage for one year,
exclusive of wear items.
Loading...