The remote control sensors are located in the front/ back of the projector. The
distance between the sensor and the remote control should not excede 6 meters.
,QWURGXFWLRQ
$FHU6OLP
FREEZE
The image can be frozen when FREEZE is pressed. A “Pause” icon will appear in
the lower right corner of the screen for three seconds. To release the freeze
function, press the FREEZE button, RETURN button or SOURCE button (when the
input source is switched over during display). A “Play” icon will appear in the lower
right corner of the screen for three seconds when the freeze function is released. .
ZOOM IN/OUT
By pressing ZOOM IN +, the center of the picture can be magnified. When the +
button is pres sed again, the picture is further m agnified, up to four tim es the origi nal
size. By pressing ZOOM OUT -, the size of the image is re duced. When the - button
is pressed again, the picture is further reduced until it is restored to its original size.
To return to the normal display mode, press the RETURN butto n. (This function can
be used in combination with FREEZE. )
,QWURGXFWLRQ
Installing or Replacing Batteries
•Push and slide the battery compartment lid in the direction shown.
•Install CR2025 as indicated by the diagram inside the compartment.
•Position the lid over the compartment and snap it back into place.
$FHU6OLP
Caution
Avoid excessive heat and humidity. Danger of explosion if battery is incorrec tl y
replaced. Replace only with the same or equi valent typ e recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.
,QWURGXFWLRQ
$FHU6OLP
,167$//$7,21
Screen Size
Place the proj ector at the required distance from the scr een according to the
desired picture size (see the table below).
1 1. 5 2
2. 5 3
4 5 6 7 8 9 10
Connecting to Various Equipment
It only takes a few seconds to connect your SL700 Series projector t o your
computer/notebook, VCR or other systems. However, a Mac adapter (an optional
accessory) is needed for connection for Macintosh users.
Computer
S-Video
RCA
VHS
Audio
,QVWDOODWLRQ
23(5$7,21
Start Up
1. Plug the power cord into a wall socket.
2. Press POWER for 1 second.
$FHU6OLP
•The back-lit POWER key blinks green and stays green when the power is
turned on.
(When the power is turned off, there is a 60-second cooling period before the
projector can be re-started.)
3. Switch on all connected equipment.
2SHUDWLRQ
$FHU6OLP
Digital Keystone Correction
Keystoning is when the projected image is noticeably wider on either the top or
bottom. To correct this, press KEYSTONE +/- (hot key) on the control panel of the
projector or on the remote control, then adjust the sliding bar labeled Keystone, as
needed. Press + to correct keystoning at the top of the image. Press - to correct
keystoning at the bottom of the im age.
Projector
Auto Adjustment
In some cases, you may have to optimize the picture quality manually. To do this,
press the AUTO key on the control panel of the projector or on the remote control.
Within 3 seconds, the built-in Intelligent Auto Adjustment function of the Acer
SL700X/S Series will present you the best picture quality.
Projector
Remote control
Remote control
2SHUDWLRQ
Source Selection
When several input sources are availabl e, press the SOURCE key to make a
selection from th e control panel of the projector or the remote contro l.
Projector
$FHU6OLP
Remote control
Source
Auto
Source
Menu System
Press
Menu again to select items in the sub-menu.
Menu
for the main menu and press or to select a sub-menu. Press
Menu Bar
Sub-menuDisplayImageControlSource
PC input
without AV
Input
Keystone
Brightness
Contrast
BlankMute
Auto resize
Phase
Frequency
Language
Mirror
Auto off
Source
Volume
Tremble
Color
Balance
Video InputKeystone
Brightness
Contrast
Sharpness
H-position
V-position
Image Ratio
System
Color
Tint
2SHUDWLRQ
Reset
Language
Mirror
Auto off
Reset
Bass
Mute
Source
Volume
Tremble
Bass
Mute
$FHU6OLP
1. Display Menu
Keystone
Brightness
2SHUDWLRQ
Loading...
+ 16 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.