Joybee 720 (DA720)
Digital Audio Player
User’s Manual
Welcome
Copyright
All rights reserved. No part of this publication may be reproduced,
transmitted, recorded, stored in a retrieval system, or translated into any
language or computer language, in any form or by any means, electronic, mechanical, recording, photocopying, or otherwise, without the
prior permission of BenQ Corporation.
Disclaimer
No warranty or representation, either expressed or implied, shall BenQ
Corporation make with respect to the quality, accuracy or fitness for any
particular purpose of this document. The information in this document
is subject to change without notice. The content of this manual has been
checked and proofread prior to publication.
*Windows is the registered trademark of Microsoft Corporation. All trademarks or product names appearing in this
manual are registered property of their respective owners.
Important Information
FCC Compliance
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
!Reorient or relocate the receiving antenna.
!Increase the separation between the equipment and receiver.
!Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
!Consult the dealer or an experienced radio/TV technician for help.
Any unauthorized changes or modifications to this equipment would
void the user’s authority to operate this device.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Cautions
!This digital audio player is a delicate electronic device, DO NOT
OPEN IT.
!Do not attempt to dissemble or modify any part of the device.
!Avoid shock or impact on the device.
!Keep the device away from water.
!Keep the device away from extreme temperatures, humidity, dust or
direct sunlight.
!Do not clean the device with chemical solvent. Clean device with a
cloth dampened with water.
!Use only adaptor and accessories approved by the manufacturer. War-
ranty voided if other adaptor or accessories are used, and danger may
occur.
!Avoid high volume which may damage hearing.
!BenQ Corporation assumes no responsibility for the loss of data due
to damage of device, repair of device and/or battery replacement.
Users are advised to back up all data on other storage device. Use of
device not in accordance with the instructions (such the cautions)
will void the warranty.
!Batteries may explode if disposed of in fire.
!Do not allow metal objects to contact the battery terminals.
!Do not short-circuit.
!Do not incinerate.
Table of Contents
Thank you for Using BenQ Joybee 720 Digital Audio
Player!............................................................................1
Introduction.......................................................................... 1
Package Contents.................................................................. 2
Minimum System Requirements ......................................... 3
Description and Functions of Different Parts ..................... 4
A Tour of the Joybee 720................................................... 4
Main Screen and Status Bar............................................... 7
The Joybee 720 Menu Tree................................................ 9
Getting Started..............................................................10
Charging the Battery........................................................... 10
Charging with DC Adapter.............................................. 10
Charging with a USB Cable ............................................. 11
Installing Drivers and Software.......................................... 12
Operation of HDD Upgrade .............................................. 13
Using SD Card .................................................................... 14
Using BenQ Joybee 720 as Digital Audio Player.........15
Transferring Files to the Joybee 720................................... 15
Transferring Files with QMusic ...................................... 15
Transferring Data with Windows File Manager............. 15
Transferring Files by SD Card......................................... 16
Main Menu.......................................................................... 16
Launching to Main Menu................................................ 16
Playing a MP3/WMA File................................................... 17
Playing an Audio File....................................................... 17
Operating the Joybee 720 When a File is Being Played.. 17
Pause a Playing File ...................................................... 17
Fast Forward ................................................................. 17
Next File ........................................................................ 18
Table of Contents i
Rewind ...........................................................................18
Previous File .................................................................. 18
Stop ................................................................................18
Adjusting Volume .........................................................18
Showing the Playlist ......................................................18
Creating the Playlist ......................................................18
Using Hot Keys .............................................................19
Locking Buttons ............................................................20
Listening to FM Radio.........................................................20
Operating the Joybee 720 When Listening to FM Radio20
FM Tuner ......................................................................20
FM Preset ......................................................................21
Viewing Pictures with the Joybee 720 ................................22
Operating the Joybee 720 When Viewing Pictures........ 22
Viewing JPEG Files .......................................................22
Showing Slides ..............................................................23
Creating Slides ..............................................................23
Deleting Slides ...............................................................24
Editing Slides .................................................................24
Adding Background Music into Slides ........................25
Erasing Files in the Joybee 720............................................25
Erase Single Audio File.....................................................25
Erase All Audio Files.........................................................26
Erase All Files ....................................................................26
Other Setups ........................................................................27
Auto Power .......................................................................27
Play Options......................................................................27
Repeat-Shuffle ...............................................................27
Intro Off/On .................................................................28
Equalizer ........................................................................28
Slide-Show Repeat ........................................................29
Date-Time.........................................................................29
Contrast.............................................................................30
Backlight............................................................................30
ii Table of Contents
Multiple Language ........................................................... 30
System Info.......................................................................... 31
Refresh DB........................................................................... 31
Using QMusic...............................................................32
Overview of QMusic........................................................... 33
Adding Music to the Joybee 720 Using QMusic ............... 37
Adding Music from an Audio CD to the Joybee 720 ..... 38
Adding Files from a PC to the Joybee 720...................... 42
Updating the Joybee 720 Automatically with QMusic ..... 45
Deleting Files Using QMusic.............................................. 49
Using the Joybee 720 as USB Hard Disk .....................51
Connecting the Joybee 720 to a PC.................................... 51
Transferring Files ................................................................ 51
Transferring a File from the Joybee 720 to a PC ............ 51
Transferring a File from a PC to the Joybee 720 ............ 52
Disconnecting the Joybee 720 from a PC .......................... 53
Troubleshooting ...........................................................55
Service ...........................................................................56
Table of Contents iii
iv Table of Contents
Thank you for Using BenQ Joybee 720 Digital Audio Player!
Introduction
Thank you for purchasing BenQ Joybee 720 Digital Audio
Player!
In this manual, you will find detailed descriptions and instructions of every function on the Joybee 720 and on QMusic as
well. Please read carefully in order to use these convenient
functions and enjoy high quality music with the Joybee 720.
Thank you for Using BenQ Joybee 720 Digital Audio Player! 1
Package Contents
Please check the contents of your Joybee 720 Digital Audio
Player. Should any accessories be missing or damaged, please
contact your dealer immediately.
BenQ Joybee 720
Digital Audio Player
Power Adapter
USB Cable
Earphones
Carrying Bag
CD-ROM
(emanual/
QMusic)
*Appearance of product shall be subject to the product inside package
2 Thank you for Using BenQ Joybee 720 Digital Audio Player!
Quick Start
Guide
Warranty
Card
Minimum System Requirements
If you want to install QMusic on a PC to convert music on an
audio CD into MP3 files for use on the Joybee 720 or use the
Joybee 720 as a hard drive disk, your PC must comply with the
following requirements:
• OS: Microsoft Windows 2000/ME/XP (QMusic supports
Windows 2000/XP)
• CPU: Pentium 200MHz or faster
• I/O port: USB
• Device: CD-ROM
• Hard drive: 40MB or more space
• Memory: 32MB or more
Thank you for Using BenQ Joybee 720 Digital Audio Player! 3
Description and Functions of Different Parts
A Tour of the Joybee 720
For the detailed description and function of different parts of
BenQ Joybee 720 Digital Audio Player, please check the fol-
lowing pictures and tables.
Right Side View
Left Side View
DC In jack
Top Vi ew
LCD display
USB cable port with
cover
SD card slot
Earphone jack
4 Thank you for Using BenQ Joybee 720 Digital Audio Player!
Strap
hole
Lock slider for power
On/ Off and lock
Description Functions
LCD Display …Displays current playing audio file data.
USB Cable Port …For connecting USB cable between the
Joybee 720 and PC. When PC is on, you
can also charge the Joybee 720 this way.
SD Card Slot …Insert SD card
DC In Jack …Allows you to use charger to recharge
the Joybee 720
Earphone Jack …For connection with earphones
Strap Hole …To attach a carrying strap
Lock Slider …Slide to power on/off the Joybee 720 or
to lock the buttons.
The Front Panel
LCD Display
Thank you for Using BenQ Joybee 720 Digital Audio Player! 5
Description Functions
…To decrease the volume while playing tracks.
…To increase the volume while playing tracks.
…Press to switch modes; or to confirm the
selection. Press and hold to exit the current
menu.
…While playing audio files, press to make
selections of EQ mode, Intro mode and
Repeat mode.
…Play the tracks. Press again to pause. Press
and hold to stop the playback.
…Press to save a new channel while searching
for a new one. Press to finish the selection
while setting modes.
…Press to confirm the selection while playing
audio files.
…To rewind the playing track. To scroll up the
menu.
…Press to select different modes while playing
audio files.
…To fast-forward the playing track. To scroll
down the menu.
…Press to select different modes while playing
audio files.
6 Thank you for Using BenQ Joybee 720 Digital Audio Player!
Main Screen and Status Bar
The bottom table shows the icons displayed on the screen and
their meanings.
Icon Description
Indicates audio file being scanned in forward
direction (Forward).
Indicates audio file is being scanned in reverse
direction (Rewind).
Indicates audio files is being paused.
Indicates audio files is being stopped.
Indicates EQ mode is off.
Indicates EQ mode as Pop.
Indicates EQ mode as Jazz.
Indicates EQ mode as Classical.
Indicates EQ mode as Rock.
Indicates EQ mode as My Own.
Indicates Intro mode is off.
Indicates Intro mode is on.
Indicates FM normal mode.
Indicates FM preset mode.
Indicates scanning FM frequency.
Indicates the normal playback mode, or repeat
mode is disabled.
Indicates single track repeat mode.
Indicates random mode.
Indicates random repeat mode.
Indicates battery status as half full.
Indicates battery status as charging.
Indicates photos in normal mode
Thank you for Using BenQ Joybee 720 Digital Audio Player! 7
Icon Description
Indicates to rotate the photo
Indicates to zoom in or our the photo
Indicates keys are locked.
8 Thank you for Using BenQ Joybee 720 Digital Audio Player!
The Joybee 720 Menu Tree
Show Title
Music
FM
Photo
Erase
File
Setup
System
Info.
Refresh
DB
Show Album
Show Artist
Show Genre
Show Folder
Show Playlist
Create Playlist
Delete Playlist
Edit Playlist
FM Tuner
FM Preset
Show JPEG File
Show Slide
Create Slide
Delete Slide
Edit Slide
Music
Music All
Delete All
Auto Power
Play Option
Date-Time
Contrast
Backlight
Multiple Language
Thank you for Using BenQ Joybee 720 Digital Audio Player! 9
Title/Album/Artist/Genre/Folder
Add Song/Delete Song
Never/1m/3m/5m/10m
Repeat-Shuffle
Intro
Equalizer
Slide-Show
Repeat
Always/10s/30s/60s/120s
English/Simplfied Chinese/Traditional Chinese
Normal/Track/All/
Random
On/Off
EQ Off/Pop/Jazz/Clas-
sical/Rock/My Own
No Repeat/Repeat All
Getting Started...
Charging the Battery
When the battery is fully charged, the Joybee 720 offers about
10 hours of continuous replay time for MP3 music. Of course,
the exact replay time is subject to the condition of battery,
operation frequency and the format of files being played.
There are two ways of charging the Joybee 720.
Charging with DC Adapter
1. Combine the two parts of charger together..
10 Getting Started...
2. Connect power adapter to a wall outlet. It takes around 4
hours to charge the Joybee 720 completely.
Charging with a USB Cable
Connect the Joybee 720 to a computer with the provided USB
cable. When charging by PC through a USB cable, please have
your PC on rather than in idle mode or off.
•
Exact charging time differs according to battery status.
Please check the battery bars on the Joybee 720 display.
When charging completes, battery bar stops illuminating.
•The life of battery depends on the frequency of charge, and
the more frequently the battery is recharged, the shorter
the replay time of device will be. It is a normal phenomenon
and not a manufacturing defect of battery.
•Chargers might vary in different areas.
Getting Started... 11
Installing Drivers and Software
The software CD provides QMusic and the relevant software
for running QMusic.
1. Put the software CD that comes with the Joybee 720 in the
CD-ROM drive on your PC. The installation menu will display on the PC screen in a few seconds.
2. Click on the icon to install the corresponding software. Follow the on-screen instructions to complete the installation.
If the installation menu does not show automatically on the
PC screen, open File Manager in Windows and locate the
‘autorun.exe’ file on the software CD. Double click the icon
to open the installation menu.
The table below shows each software and its content descrip-
tion on the Software CD.
Item Description
Install BenQ
QMusic
Install Windows Media
Player
QMusic is a powerful music manager. It not
only allows you to play audio CD and MP3
files and to convert audio CD sound tracks
into MP3 formats, but also auto search CD
sound tracks database when your PC is connected to the internet. With QMusic, you
can save your music files on the Joybee 720,
and organize and update the data stored on
the Joybee 720.
Please note that QMusic supports only Windows 2000/XP. No CD burning function on
Windows 2000.
QMusic must work with Windows Media
Player 9. If you do not have it in your PC,
please install it first in order to run QMusic.
12 Getting Started...
Install Direct X QMusic must work with Windows Direct X.
If you do not have it in your PC, please
install it first in order to run QMusic.
Install Acrobat
Reader
Read User’s
Manual
BenQ Joybee
720 Recovery
Program
To re a d t he Joybee 720 e-manual on your PC
requires Adobe Acrobat Reader. Please
install this to open emanual if you don’t have
it.
For more information on the instructions of
the Joybee 720, please click to open user’s emanual.
To re co ve r t he Joybee 720 system if the crucial files to the Joybee 720 are renamed,
removed or deleted by accident.
Operation of HDD Upgrade
Please do not rename, remove or delete the file named as
“system\pp5020.mi4” and the folder “system\font” in your
Joybee 720. Any intention to rename, remove or delete the two
files will cause irreversible damage to the Joybee 720 and lead
to system crash.
If you remove the two files by accident, please follow the steps
to reconstruct the system of the Joybee 720.
1. Connect the Joybee 720 to your PC with provided USB
cable.
2. Insert the provided software CD into the CD-ROM drive of
your PC.
3. Select BenQ Joybee 720 Recovery Program from the CD
menu.
4. Please follow the on-screen instructions to format or
upgrade the system of the Joybee 720.
Please note that you will lose all the data stored on the Joybee 720 if you format the player. The recovery program only
Getting Started... 13
provides the necessary files so that the system of the Joy-
bee 720 can be reconstructed.
Using SD Card
The Joybee 720 supports reading data on a SD card. Please follow the steps to use a SD card.
1. Eject the dummy card in the player’s SD card slot.
2. Insert the SD card into the SD card slot.
3. The data on the SD card start being transferred to the Joybee 720 automatically.
4. After the transfer is complete, press Refresh DB from Main
Menu so that the new files can be sorted according to their
formats.
Please note that files in all formats can be stored on the
•
Joybee 720, yet the player recognizes files in MP3, WMA
and JPEG formats only; you have to use File Manager on
the PC to read the files other than these formats.
•QMusic does not support reading SD cards.
•Files on the Joybee 720 cannot be transferred to the SD
card.
14 Getting Started...
Using BenQ Joybee 720 as Digital Audio Player
Transferring Files to the Joybee 720
The Joybee 720 offers you three choices in transferring the
audio files so that you can add any new audio files from any
PC whenever you want.
You can choose to use QMusic to edit and transfer the files to
the Joybee 720 when you have it. Or you can just copy-paste
new audio files to the Joybee 720 with Windows File Manager
and find the files in the folder named MP3 in your Joybee 720.
The second way allows you to transfer audio files and play
them even when the PC you are using doesn’t have QMusic on
it. The third way to transfer files to the Joybee 720 is using SD
cards.
Transferring Files with QMusic
Turn on your Joybee 720 and connect it to your PC using the
USB cable provided as described in "Connecting the Joybee
720 to a PC" on page 51. Refer to "Adding Music to the Joybee
720 Using QMusic" on page 37 for detailed information about
transferring files to your player using the QMusic software.
Transferring Data with Windows File Manager
1. Connect the Joybee 720 to a PC with the USB cable as
described in "Connecting the Joybee 720 to a PC" on page
51.
2. If you already have MP3 (.mp3), WMA (.wma) or JPEG
(.jpg) files on your hard disk, locate them using the File
Manager.
Using BenQ Joybee 720 as Digital Audio Player 15
3. Select the desired files and drag them to the new Removable
Disk. By doing so, the selected files will be transferred to the
Joybee 720.
4. Press Refresh DB from Main Menu of Joybee 720 to refresh
the database, so that your Joybee 720 will detect the formats
of the new added files and classify them to the correct folders. Only by doing so can you read or play the new files.
•
When files are being transferred to the Joybee 720, do not
disconnect the Joybee 720 from the PC. Use the procedure
described in "Disconnecting the Joybee 720 from a PC" on
page 53 to disconnect it.
•Check if there is enough HDD space on the Joybee 720
before transferring files to it.
Transferring Files by SD Card
Please refer to "Using SD Card" on page 14 for the detailed
instruction.
Main Menu
All functions on the Joybee 720 are accessible from Main
Menu. Therefore, all you need to do is to remember how to
operate the function menu as shown in the following instructions in order to use these functions and change their settings.
Launching to Main Menu
1. Slide the power switch into on and turn the Joybee 720 on.
2. In standby mode, you can see the main function menu list.
Use the buttons of and to scroll up and down;
move the highlight on menu list and press to
enter.
3. Press and hold to exit the current menu and
return to the previous menu.
16 Using BenQ Joybee 720 as Digital Audio Player
Playing a MP3/WMA File
You can play and edit playlists of audio files or change the set-
ting of playback.
Playing an Audio File
1. Turn on the Joybee 720.
2. Scroll and to move highlight to Music and
press to enter.
3. In Music mode, there are ways of showing audio files for
you to select. Use and to move highlight to
the desired setting and press to confirm.
3. Scroll and to select the desired track and
press to play.
4. Press and hold to exit the current menu. You can
make other settings or viewing pictures while playing the
music at the same time.
•
All audio files will be sorted automatically and are classified by Title, Album, Artist, Genre or Folder by pressing
Refresh DB in the Main Menu.
•The player starts playing from the first track of Show Title if
you press
Operating the Joybee 720 When a File is Being Played
Pause a Playing File
When a file is being played, press to pause and to play
the file again.
Fast Forward
When a file is being played, press and hold to fast forward.
.
Using BenQ Joybee 720 as Digital Audio Player 17
Next File
When a file is being played, press to skip to the next file.
Rewind
When a file is being played, press and hold to rewind.
Previous File
When a file is being played, press to skip to the previous file.
Stop
When a file is being played, press and hold for about 2
seconds to stop playing.
Adjusting Volume
When an audio file is being played, press or to
increase or decrease volume.
Showing the Playlist
1. Select Music from Main Menu and press .
2. The playlist edited by QMusic will be displayed as QMusic;
other playlists created in Create Playlist will be displayed as
Playlist1, Playlist2 and so on. Use and to
choose playing audio files according different playlists.
Press to confirm.
3. Press to start playing the selected playlist.
Creating the Playlist
Audio files can be listed according to different titles, album
names, artists, genres or folder names; a new playlist can be
created or edited according to these information, too.
1. Select Music from Main Menu and press .
18 Using BenQ Joybee 720 as Digital Audio Player
2. Use and to move the highlight and select Create Playlist, then press to enter.
3. Use and and choose to list the audio files
according to titles, albums, artist, genres, or folders, then
press to enter.
4. Files classified by these items are shown, use and
to move the highlight, then press to con-
firm the files being selected. A number on the bottom left of
the screen will show the number of tracks added in this new
playlist.
5. Scroll and to select more trakcs from the
same menu, or press
return to the previous menu. Repeat step 1 to 4 to select
more desired tracks.
6. To play the new playlist, please go to Show Playlist from
Music mode. Use and to select the desired
playlist and press to play it.
to finish the selection and
Using Hot Keys
Using hot keys as an access to change the settings of EQ mode,
Intro mode, and Repeat-Shuffle while playing audio files.
1. Press while playing audio files. The icon on
the status bar at the bottom of the screen is highlighted. You
are now able to use and to switch between EQ
modes of Normal, Pop, Jazz, Classical, Rock and My Own.
2. Press to confirm the setting and exit the selection,
or press again to exit the setting of EQ mode and
enter the selection of Intro mode and Repeat-Shuffle mode.
3. Use and to switch between Intro On and Off.
Press to confirm the setting and exit the selection,
Using BenQ Joybee 720 as Digital Audio Player 19
or press again exit the setting of Intro mode and
enter the selection of Repeat-Shuffle mode.
4. Use and to switch between different RepeatShuffle modes of Normal, Tr a c k, All and Random. Press
to confirm the selected setting and exit.
All the operations of the Joybee 720 but FM radio are not
restricted to the function of playing audio files. In other
words, you can play music or other audio files as background music while operating other functions like viewing
photos. You can simply press in any menu and play
the audio files.
Locking Buttons
Slide the power switch to the middle, an icon of will
appear on the screen until unlock the buttons. The function is
to avoid any touches that cause unexpected change during
your use of the Joybee 720.
Listening to FM Radio
There are two ways to choose the FM channels you prefer; you
can choose from the preset ones or to search for a new one
automatically. The Joybee 720 allows you to save 16 channels.
Operating the Joybee 720 When Listening to FM Radio
FM Tuner
1. Turn on the Joybee 720.
2. Use and to move the highlight to FM, and
press to enter.
3. Select FM Tuner and press to confirm.
4. In FM mode which can be identified by the icon
on the top of the screen, the OSD shows the present channel
20 Using BenQ Joybee 720 as Digital Audio Player
you are listening to. Use and to locate the frequency manually.
5. Press to save the present channel as one of the preset channels.
6. If you want to enter the menu of the preset channels which
can be identified as on the top of the screen,
press , use or to choose one from the
16 preset channels.
7. If you want to search for the frequency automatically, press
again to enter the auto-scan mode (which can be
identified as on the top of the screen). Press
and a message shows the Joybee 720 is scanning.
After the auto-scan is done, it will show an valid channel.
8. You can always adjust the volume while listening to FM
radio by pressing and .
9. To exit the present menu, press and hold .
Please note that the new available channels you get from
auto-scan mode will override all the previous preset channels and become the new preset ones.
FM Preset
Basically this function provides an access to listen to 16
present FM channels. You will enter the same mode as FM
Tu ne r after selecting the channel.
1. Enter FM mode from Main Menu by pressing .
2. Use and to select FM Preset and press
to enter the menu of FM Preset.
3. 16 channels are listed on the OSD. Use and to
select one channel and press to listen to it. Flow
the steps in the section of “FM Tuner” to make further setting.
Using BenQ Joybee 720 as Digital Audio Player 21
4. To exit the present menu, press and hold .
Viewing Pictures with the Joybee 720
The colored LCD monitor allows the Joybee 720 for showing
pictures and slides in JPEG format.
Operating the Joybee 720 When Viewing Pictures
Please refer to "Transferring Data with Windows File Manager" on page 15 before viewing, creating or editing pictures or
slides.
Viewing JPEG Files
1. Use and to select Photo from Main Menu and
press to confirm.
2. In the menu of Photo, select Show JPEG File and press
to confirm.
3. The thumbnails of all JPEG files are displayed on OSD. Use
and to select the picture you want to see or go
to the next/previous page.
4. Once the picture is selected, press to view the fullsize picture. An icon will displayed on OSD and
indicates that the photo is in normal mode. Press
to switch between normal mode, rotation mode ,
and zoom mode .
5. Use and to go to the next/previous picture in
normal mode; to rotate in rotation mode or to zoom in and
zoom out in zoom mode.
6. Press and hold to exit.
22 Using BenQ Joybee 720 as Digital Audio Player
Showing Slides
1. Use and to select Photo from Main Menu and
press to confirm.
2. In the menu of Photo, select Show Slide and press
to confirm.
3. Use and to select the slideshow you want to
play, then press to confirm.
4. To stop the play of slideshow, press and hold and
go back to the previous menu.
Creating Slides
1. Use and to select Photo from Main Menu and
press to confirm.
2. In the menu of Photo, select Create Slide and press
to confirm.
3. Use and to move to the frame you would like
to add JPEG picture, and press to confrim.
4. The OSD displays the thumbnails of all pictures; there are
six pictures per page. Use and to turn to next/
previous page.
5. Use and to select the picture and press
to confrim.
6. Repeat the step 3 to 5 and have the new slide complete. Press
to finish creating slides. The system will enter the
playlist of audio files at the same time. You can use
and to select one audio file as the background music
of the newly-created slide and press to confirm, or
just press to quit the music playlist.
7. Press and hold to exit the Create Slide mode.
Using BenQ Joybee 720 as Digital Audio Player 23
Deleting Slides
1. Use and to select Photo from Main Menu and
press to confirm.
2. In the menu of Photo, select Delete Slide and press
to confirm.
3. The OSD shows the lists of all the slides, use and
to select the slides you want to delete. Press
to confirm.
4. A dialog box will popup and asks if you want to delete the
selected file. Use and to select the answer of
yes or no, and press to confirm.
Editing Slides
You can replace pictures in the created slides with new ones,
insert new pictures into a proper position, or delete pictures.
Of course, the background music can be edited, too.
1. Use and to select Photo from Main Menu and
press to confirm.
2. In the menu of Photo, select Edit Slide and press
to confirm.
3. Use and to select the slides you want to edit,
then press to confirm.
4. The structure of the selected slide is displayed. Use
and to select the picture you want to edit, and press
to confirm.
5. Whether you want to replace, insert or delete a picture, a
dialog box will popup and confirm next action. Use
and to select the next step and press to
confirm.
24 Using BenQ Joybee 720 as Digital Audio Player
6. If you choose to replace with or insert a picture, the OSD
displays the thumbnails of all pictures. Use and
to select the picture you like and press to
confirm.
7. If you choose to delete the picture, use and to
select Delete in the dialog box and the picture will be
deleted.
8. To edit the background music, follow step 1 to 3 and enter
the selected slide. Press and the playlist of audio
files will be displayed. Use and to select the
desired audio file and press to confirm.
Adding Background Music into Slides
You can enjoy listening to the music while viewing the slides
by the following the steps.
1. Please refer to the step 1 to 5 mentioned in "Creating Slides"
on page 23 and adding pictures to the new slide.
2. Press and enter the playlist.
3. Use and to select an audio file as the background music while playing slideshow. Press to
confirm, and the system goes back to the menu of Photo
directly.
Erasing Files in the Joybee 720
A good way to make the Joybee 720 to wor k better is to remove
the unnecessary files. There are three modes of erasing files.
Erase Single Audio File
1. Use and to select Erase File from Main Menu
and press to enter.
Using BenQ Joybee 720 as Digital Audio Player 25
2. Use and to select Musi c, then press
to enter.
3. Use and to select the audio file you want to
erase, then press to confirm.
4. A dialog box will appear on the OSD and ask if you want to
preceed the deletion. Use and to select your
answer as yes or no, and press to confirm.
Erase All Audio Files
1. Use and to select Erase File from Main Menu
and press to enter.
2. Use and to select Music All, then press
to enter.
3. A dialog box will appear on the OSD and ask if you want to
preceed the deletion. Use and to select your
answer as yes or no, and press to confirm.
Erase All Files
1. Use and to select Erase File from Main Menu
and press to enter.
2. Use and to select Delete All, then press
to enter.
3. A dialog box will appear on the OSD and ask if you want to
preceed the deletion. Use and to select your
answer as yes or no, and press to confirm.
26 Using BenQ Joybee 720 as Digital Audio Player
Other Setups
Adjust the setting of the Joybee 720 according to your preference, and make the Joybee 720 a good company.
Auto Power
A function to save power while the system is idle.
1. Enter Setup from Main Menu. Press to enter the
submenu.
2. Use and to select Auto Power, then press Press
to confirm.
3. There are 5 options for power saving. Off means to keep the
power on all the time. You can also choose to shut down
the system after 1, 3, 5, or 10 mins. Use and
to select the desired setting and press to confirm.
4. While the system if off automatically, press any key to power
on the Joybee 720 again.
Play Options
Four play options of the Joybee 720 refer to the use of playing
audio files and pictures/slides.
Repeat-Shuffle
About the setting of the repeat mode of playing audio files,
please refer to "Using Hot Keys" on page 19 or the following
steps.
You can set the playback mode before or while playing the
audio files.
1. To choose the playback mode, select Setup in Main Menu
and press to enter.
2. Use or to move the highlight and select Play
Option by pressing .
Using BenQ Joybee 720 as Digital Audio Player 27
3. In the Play Option menu, select Repeat-Shuffle and press
to confirm.
4. There are four playback modes for you to choose (Normal,
Tr a ck , All, and Random). Select one you prefer by using
and , then press to confirm.
5. To go back to the previous menu, please press and
hold it for a second.
Intro Off/On
The Joybee 720 provides the function to preview the playing
music.
1. Enter the submenu of Setup from Main Menu by pressing
.
2. Choose Play Option and press to confirm.
3. Choose Intro On or Intro Off, then press to con-
firm.
4. Press and hold to go back to the previous menu.
Equalizer
There are two ways to select an EQ mode.
Using Hot Keys
Please refer to "Using Hot Keys" on page 19, or do as the following instructions.
Select from the Menu
1. When a file is being played, press and hold twice to
go back to Main Menu.
2. Use and to move the highlight to Setup and
press to enter. Choose Play Option and press
to enter.
28 Using BenQ Joybee 720 as Digital Audio Player
3. In the menu of Play Option, use or to select
Equalizer and press to make sure. There are 6
built-in EQ modes in the Joybee 720 (Normal, Pop, Jazz,
Classical, Rock, and My Own), but you can always create a
mode you like.
4. Once decided, press to confirm.
5. Press and hold to return to the previous menu.
Slide-Show Repeat
Choose the repeat mode of slideshows by following the steps.
1. Enter the submenu of Setup from Main Menu by pressing
.
2. Choose Play Option and press to confirm.
3. Use and to select Slide-Show Repeat and press
to confirm.
4. Choose No Repeat or Repeat All and press to confirm.
5. Press and hold to exit the menu.
Date-Time
To setup the time of the system, please follow the steps.
1. Enter the submenu of Setup from Main Menu by pressing
.
2. Choose Date-Time and press to confirm.
3. Use and to move to the setting of time or
date. Press or to increase or decrease the
numbers on the screen. Press to confirm.
4. After the setting is done, press and hold to exit.
Using BenQ Joybee 720 as Digital Audio Player 29
Contrast
To adjust LCD contrast, please follow the steps.
1. Enter the submenu of Setup from Main Menu by pressing
.
2. Choose Contrast and press to confirm.
3. There will be a horizontal scroll bar on the screen. Use
and to adjust the LCD contrast.
4. Press to confirm and exit.
Backlight
There is a backlight timer to set backlight duration. Backlight
will turn off automatically after the time duration you set.
1. Enter the submenu of Setup from Main Menu by pressing
.
2. Choose Backlight and press to confirm.
3. There are choices of 10, 30, 60 and 120 seconds backlight on
and always on. Use and to select the desired
option, then press to confirm and exit.
Multiple Language
You can decide the language shown on the LCD display.
1. Enter the submenu of Setup from Main Menu by pressing
.
2. Choose Multiple Language and press to confirm.
3. Use and to select from options of English,
Simplfied Chinese and Traditional Chinese. Then press
to confirm.
4. Press and hold to exit.
30 Using BenQ Joybee 720 as Digital Audio Player
System Info.
System information reveals the current firmware version, total
memory and HDD information. To view the system information, please follow the steps.
1. Enter System Info from Main Menu by pressing .
2. The following information are displayed:
• Firmware version
• Software version
• SDRAM capacity
• SD card capacity
• File system format
• HDD used space
• HDD free space
• HDD capacity
Refresh DB
This function allows you to refresh your database every time
after transferring files from PC. The Joybee 720 cannot classify
the new audio and vedio files and add them into the playlists
until the database is refreshed. If the database is not refreshed
after the files are transferred, possible consequences are either
the new files cannot be displayed on LCD or the filenames are
shown incorrectly.
To refresh the database, please select Refresh DB from Main
Menu and press to confirm. Then wait until the
BenQ logo is displayed on LCD and the Main Menu appears.
Using BenQ Joybee 720 as Digital Audio Player 31
Using QMusic
QMusic is software provided to help you to organize your
music collection. You can use it to play audio CDs or MP3s on
your PC, convert audio CD tracks into MP3 format, create
playlists, transfer music to your the Joybee 720, burn music
CDs and create your own music album.
The QMusic icon appears on your Desktop after it is suc-
cessfully installed as described in "Installing Drivers and Software" on page 12. Double click the icon to launch QMusic.
Alternatively, you can start QMusic by clicking Start on the
Windows taskbar and clicking Programs, QMusic2 and then
QMusic2.
32 Using QMusic
Overview of QMusic
The user interface of the QMusic program is shown in the
illustration below.
Actio n
buttons
Display
System
buttons
Left
panel
Playback
buttons
Right
panel
Status
bar
Using QMusic 33
Feature
buttons
Search
window
Features Description
Action
buttons
Provides specific QMusic functions.
Left button: Convert CD audio tracks
to MP3 formats.
Right button: Add audio files saved in
your PC to either Music Libr ary or
MP3 folder under the Joybee 720.
Left
Displays all files supported by QMusic.
panel
There are two default folders in your hard disk:
Music Li brary and My Joybee. You can save and
organize your audio files here.
Music Li brary: All your MP3 audio files
transferred from audio CD tracks would be saved
in the folders under this root database.
QMusic can auto-search CD album title
and CD tracks database when your PC is
connected to the internet.
34 Using QMusic
Playback
buttons
My Joybee: QMusic automatically synchronizing
function folder. When you set the Joybee 720 MP3
player automatically synchronizing every time the
Joybee 720 MP3 player is connected to your PC,
the audio files in the Joybee 720 will be replaced by
the files here.
Joybee720(F:4595 Mb Available\Capacity...): This
appears when your Joybee 720 MP3 player is
connected to your PC. F stands for the Joybee 720
player as a removable drive and the digits
following are current HDD space usage status.
MP3: the Joybee 720 default folder. You can
directly drag and drop your audio files saved under
the Music Library to this folder, or you can just
right click the folder and select Add song to copy
audio files saved in your hard disk to this folder.
Playlist: You can right click this folder to create
sub-playlists to organize all your audio files in the
Joybee 720/ MP3 folder. Create different playlists,
drag and drop the audio files from the Joybee 720/
MP3 folder to each playlist, and you can
reorganize the playback order in each album.
Provides functions such as playing a
selected file, skipping to the next or
previous files, pausing playback, stopping
playback, ejecting a CD, and volume
control.
Status
bar
Displays details of files, such as total number of
files and playing time.
Using QMusic 35
Feature
buttons
Sets repeat or random playing of files in
playback mode and provide additional
options.
Setting butting: Click to have general
settings dialogue box.
Repeat button: Click to repeat playback all
tracks.
Random button: Click to random play all
tracks.
EQ button: Click to display EQ control
panel.
Right
panel
Search
window
Displays the files in the folder or media selected in
the left panel.
Provides searching function. Type in a file name
and press the magnifier icon to search for a
particular file.
System
Control QMusic window.
buttons
Display Displays progress of an action. For example, when
an audio file is being played, the name, elapsed
playing time and other information of the file is
displayed here.
For more detailed information on buttons function, please
•
refer to HELP file.
•Please note that QMusic cannot detect SD cards, therefore
files on SD card and the card itself will not be shown in the
left panel of QMusic window.
36 Using QMusic
Adding Music to the Joybee 720 Using QMusic
Connect the the Joybee 720 to the PC using the procedure
described in "Connecting the Joy bee 720 to a PC" on page 51.
The icon of the Joybee 720 appears in the left panel of the
QMusic interface, and the directories on the Joybee 720 are
displayed under the icon.
You can now add files to your Joybee 720 from an audio CD
using the file conversion facility provided by QMusic or you
can directly copy your audio music files from the PC to the
Joybee 720.
Using QMusic 37
Adding Music from an Audio CD to the Joybee 720
1. Put an audio CD in the CD-ROM on your PC. The
icon appears in the left panel of QMusic, and the
files on the CD appear in the right panel.
2.
Select the files to be added to the Joybee 720 by clicking the
check boxes in front of the files.
38 Using QMusic
3. Click the icon, and QMusic starts converting the
selected files into MP3 files.
4. After the conversion is completed, a New Album is added to
the left panel. All the converted files are placed in this
album. Click the New Album to display the details of files in
the right panel.
Using QMusic 39
5. Select the files to be added to the Joybee 720. To select more
than one file, press and hold the Ctrl key on the keyboard
while selecting the files. To select all files, click the first file,
press and hold the Shift key on the keyboard, and then click
the last file. If you want to delete files, select files and press
the Delete key on the keyboard.
40 Using QMusic
6. Drag to copy the selected files from the right panel to the
MP3 directory under the icon indicates as the Joybee 720.
Check if there is enough HDD space on the Joybee 720
before transferring files to the Joybee 720.
Using QMusic 41
Adding Files from a PC to the Joybee 720
Follow these steps to add files from a PC to your Joybee 720.
1. Click the My Joy bee folder in the left panel.
42 Using QMusic
2. Press to open a dialogue box for selecting files. Browse
and select MP3 or WMA files to be add to the Joybee 720
from the PC. Press Open to add the selected files to My Joybee.
3. Click the Joybee 720 icon on the QMusic interface.
Using QMusic 43
4. Press and QMusic starts transferring the files in the My
Joybee folder to the Joybee 720. Before transferring the
selected files to the Joybee 720, QMusic shows a dialog box
to ask if you want to delete the existing files in the My Joybee folder. If you want to keep them, abort the transfer and
back up these files, before starting file transfer again.
Check if there is enough HDD space on the Joybee 720
before transferring files to the Joybee 720.
44 Using QMusic
Updating the Joybee 720 Automatically with
QMusic
You can set up the Joybee 720 to be updated with the music
from the My Joybee folder automatically when it is connected
to the PC.
1. Click the My Joy bee folder in the left panel.
Using QMusic 45
2. Press to open a dialogue box for selecting files. Browse
and select MP3 or WMA files to be added to the Joybee 720
from the PC. Press Open to add the selected files to My Joybee.
3. Press on the right panel of QMusic in the function button area.
46 Using QMusic
4. In the Option dialog box shown, click the Joybee tab.
5. Select Automatically launch QMusic when Joybee added
under Launch Settings and Automatically transfer MP3 files
Using QMusic 47
to Joybee when added under Update Settings. Click the
button to save your settings.
6. Connect the Joybee 720 to the PC and QMusic automatically updates the files on the Joybee 720 with the files in My
Joybee folder.
From now on, if you want to automatically update files on the
Joybee 720, you only need to save files in the My Joybee folder
and connect the Joybee 720 to your PC. QMusic automatically
transfers the files in the folder to the Joybee 720.
Check if there is enough HDD space on the Joybee 720
before transferring files to the Joybee 720.
48 Using QMusic
Deleting Files Using QMusic
Use the following procedure to delete files on your Joybee 720
using QMusic.
1. Start QMusic.
2. Turn on the Joybee 720 and connect it to the PC using the
USB cable.
3. Locate the files to be deleted by clicking on the MP3 subdirectory under the Joybee 720 icon in the left panel of QMusic.
Using QMusic 49
4. The files in the selected directory are displayed in the right
panel. Click to select the file to be deleted. To select more
than one file, press and hold the Ctrl key on the keyboard
while selecting the files. To select all files, click the first file,
press and hold the Shift key on the keyboard, and then click
the last file.
5. Press the Delete key on the keyboard to delete all selected
files from the Joybee 720.
50 Using QMusic
Using the Joybee 720 as USB Hard Disk
Connecting the Joybee 720 to a PC
1. Connect the Joybee 720 to a PC with the USB cable provided.
2. When the Joybee 720 is successfully connected to the PC, a
new icon “JOYBEE 720” will appear in My Computer window in Windows XP, or as a “Removable Disk” in other OS.
If the dialog box “Windows found new hardware” keeps appearing on
the PC screen after the connection, press Next or OK to close the dialog
box.
3. Now, you may cut, copy and paste files stored on the Joybee
720 with File Manager as you are working on any fixed disk.
When files are being transferred to the Joybee 720, do not
•
disconnect the Joybee 720 from the PC.
•Please check if there is enough HDD space on the Joybee
720 before transferring files to the Joybee 720.
•If the files transferred to the Joybee 720 are in WMA and
MP3 formats, you can play them on the Joybee 720.
Transferring Files
Yo u ca n t ran sfe r f il es f ro m t he Joybee 720 to your PC or from
PC to the Joybee 720.
Transferring a File from the Joybee 720 to a PC
1. Refer to the steps in "Connecting the Joybee 720 to a PC" on
page 51 and make the connection.
2. Click My Computer or Windows Explorer on your PC. The
Joybee 720 will appear as a removable drive.
3. Double click the icon that refers to the Joybee 720. The PC
will list out the folders stored on the Joybee 720.
Using the Joybee 720 as USB Hard Disk 51
4. Double click the folder that contains the file you want to
transfer, then right-clikc the file and choose to Copy.
5. In My Computer or Windows Explorer on the computer,
locate the folder you want to copy the file to, then rightclick the folder and click Paste. The file is transferred from
the Joybee 720 to your computer.
Transferring a File from a PC to the Joybee 720
1. Connect the Joybee 720 to your computer with the USB
cable which comes with the package. For more information,
refer to "Connecting the Joybee 720 to a PC" on page 51.
2. Click My Computer or Windows Explorer on the computer,
then locate the file you want to copy to the Joybee 720.
3. Right-click the file, then click Copy.
4. In My Computer or Windows Explorer on the computer,
locate the icon of the Joybee 720, which is usually labelled as
“removable drive.”
5. Double click the icon of your Joybee 720, then the computer
shows the list of the folders stored on Joybee 720.
6. Double click the folder you want to copy the file to, then
right-click the folder and click Paste. The file is transferred
to your Joybee 720.
52 Using the Joybee 720 as USB Hard Disk
Disconnecting the Joybee 720 from a PC
1. Double click the USB device icon on the task bar tray.
2. A dialog box as shown below will appear on the screen.
Select USB Mass Storage Device in the dialog box and press
Stop.
3. Another dialog box as shown bellow will appear on the
screen. Select BenQ Joybee 720 USB Device and press OK.
Using the Joybee 720 as USB Hard Disk 53
4. Close the dialog box appears on the bottom of the screen
and disconnect the Joybee 720 from the PC.
Operation procedure may differ from one OS to another.
54 Using the Joybee 720 as USB Hard Disk
Troubleshooting
Unable to transfer files to the Joybee 720:
Please check the following:
• Check if the USB cable has been securely connected to a PC
and the Joybee 720. The Joybee 720 is turned on automatically when connecting to a PC.
• Check if USB driver has been installed on your PC system.
Data stored in the Joybee 720 is lost.
When power supply is unstable while the Joybee 720 is connected to a PC, it may cause data loss. Hence, we strongly recommend you to back up all data stored in the Joybee 720.
BenQ Corporation shall make no representation on damage or
indemnification arising out of loss of data.
I can’t see anything on the screen of the Joybee 720.
Check battery status and if the Power Switch set to ON.
Troubleshooting 55
Service
If you cannot solve the problems found on the Joybee 720 with
the troubleshooting guide, please contact our worldwide service locations to obtain the latest drivers and online services.
Area Countr y Te le ph on e N um be r E-mail Address or Website
Asia China +86-512-68092520 service@benq.com.cn
Hong Kong +852-23306188 service@benq.com.hk
Taiwan 0800-027-427 Support@BenQ.com
Singapore +65-6296-2919 *
Thailand +66-2-6700310-1
Malaysia +603-7725-4168
Australia Australia 61-1300-130-336 *
The
Nethe rlands
Belgium +32(0)2-645-32-52
Germany 0180-3232002 www.BenQ.de
Switzerland +41(0)22-567-5331 www.BenQ.ch
Europe
Italy 02-7541-9780 www.BenQ.it
UK/Ireland 0906-753-3443 www.BenQ.co.uk
Spain
Por tugal
Austria 01-360-2772-062 www.BenQ.at
Europe
Romania +40(0)259-342431
Poland 032-373-6168
USA
America
Canada
Latin America
0900-2367-669 www.BenQ.nl
91-754-7015
+886-600-2367
www.BenQ.es
*
56 Service
The United
Arab Emirates
Iran
Middle
Kuw ait
East
Ye m e n
Qatar
Saudi Arabia
* Please link to http://support.benq.com
** *
and enter Contact
Center, then Ask the Expert. Select the desired language and
then Start a new case if you want to ask a new question.
** Please link to http://support.benq.com
and enter Contact
Center. Select Service Location and then the country. You will
be able to find the phone number of the local service center
from the Internet.
For users in Europe, to avoid any unnecessary inconvenience with your BenQ product, we suggest that you read
the instruction manual carefully and must visit our website,
www.benq-eu.com for the details of warranty terms and
conditions before contact our service agent.
Service 57
Loading...