BENDIX BIW 1000W, BIW 1200W Operating & Installation Instructions Manual

WASHING MACHINE

BIW 1000W
BIW 1200W

OPERATING & INSTALLATION

INSTRUCTIONS

124971941

2

Installation

■

This appliance is heavy. Care should be taken when
moving it.

■

It is dangerous to alter the specifications or attempt
to modify this product in any way.

■

All packing and transit bolts must be removed before
use. Serious damage can occur to the product and to
property if this is not adhered to. See relevant section
in instructions.

■

Any plumbing work required to install this appliance
should be carried out by a qualified plumber or
competent person.

■

Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.

■

Care must be taken to ensure that the appliance does
not stand on the electrical supply cable.

■

If the machine is situated on a carpeted floor, please
adjust the feet in order to allow air to circulate freely.

Child Safety

■

This appliance is designed to be operated by adults.
Children should not be allowed to tamper with the
controls or play with the product.

■

Pets and children have been known to climb into
washing machines. Please check your drum before
use.

■

The glass door becomes very hot during the washing
cycle. Keep children away from the vicinity of the
appliance whilst it is in operation.

■

Keep all packaging well away from children.

■

Keep all detergents in a safe place out of children’s
reach.

Use

■

Always unplug the appliance and turn off the water
supply after use.

■

Do not overload the appliance. See relevant section
in the instruction book.

■

Only wash fabrics which are designed to be machine
washed. If in doubt, consult the care label on the
clothes.

■

Before washing, ensure that all pockets are empty
and buttons and zips are fastened. Avoid washing
frayed or torn articles and treat stains such as paint,
ink, rust, and grass before washing. Underwired bras
must NOT be machine washed.

■

Any objects such as coins, safety pins, nails, screws,
stones or any other hard, sharp material can cause
extensive damage and must not be placed into the
machine.

■

Garments which have been in contact with volatile
petroleum products should not be machine washed.
If volatile cleaning fluids are used, care should be
taken to ensure that the fluid is removed from the
garment before placing in the machine.

■

Wash small items such as socks, laces, washable
belts etc in a washing bag or pillow case as it is
possible for such items to slip down between the tub
and the inner drum.

■

Only use the advised quantities of fabric softener.
Damage to the fabric can ensue if you over-fill.
Refer to the manufacturer’s recommendations of
quantities.

■

As some duvets and eiderdowns should be washed
in large commercial machines because of their bulk,
please check with the manufacturer of the item
before washing in a domestic machine.

■

Leave the porthole door slightly ajar between washes
to preserve the door seal.

■

Under no circumstances should you attempt to repair
the machine yourself. Repairs carried out by
inexperienced persons may cause injury or serious
malfunctioning. Contact your local Electrolux
Service Force Centre. Always insist on genuine
Electrolux spare parts.

Important Safety Information

It is most important that this instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move
house and leave the appliance, always ensure that the book is supplied with the appliance in
order that the new owner can get to know the functioning of the appliance and the relevant
warnings.

These warnings have been provided in the interest of safety. You MUST read them carefully
before installing or using the appliance.

3

Contents

For the User

Important Safety Information

2

Your New Washing Machine

4

Description of the Appliance

5

Detergent dispenser drawer 5

The Control Panel

6

Operating sequence

7-10
Washing 4.5 kg of white cotton at 95°C 7
Load the laundry 7
Measure out the detergent 7
Measure out the fabric softener 7
Select the required option 7
Select the required programme 7
Start the machine 8
At the end of the programme 8

Washing 2.5 kg of mixed fabrics at 50°C 9
Load the laundry 9
Measure out the detergent 9
Measure out the fabric softener 9
Select the required option 9
Select the required programme 9
Start the machine 9
At the end of the programme 10

Washing Hints

11-12

Which detergent?.... 12

And in which form? 12

Wash Care Symbols

13

Washing Programmes

14-15

Maintenance and Cleaning

16-17
Descaling 16
After each wash 16
External cleaning 16
Cleaning the dispenser drawer 16
Cleaning the drawer recess 16
Cleaning the filter 16
The dangers of freezing 17
Maintenance wash 17

Something Not Working

18-19

Service and Spare Parts

19

Guarantee Conditions

20

Electrolux Service Force

21-22

For the Installer

Installation Instructions

23

Technical Specifications

23

Unpacking 24
Positioning 24
Water inlet 24
Water drainage 25
Levelling 26
Special conditions 26
In the interest of the environment 26
Electrical connection 27

Guide to use the Instruction Book

The following symbols will be found in the text to guide you throughout the instructions:

Safety instructions
Hints and tips
Environmental information

4

Your New Washing Machine

Your new washing machine meets all modern requirements for effective treatment of laundry
with low water, energy and detergent consumption.

■

Automatic cooling of the wash water to 60°C

before draining, with the 95°C programme. This
reduces thermal shock to fabrics, helping to prevent
creasing.

■

The special wool programme with its new delicate
wash system treats your woollens with extreme care.

Ecological hints

To save water and energy and help protect the
environment, we recommend that you follow these
hints:

■

Adjust the quantity of detergent according to the
hardness of your water supply, the amount of
laundry and the degree of soiling.

■

A programme without prewash is sufficient for
normally soiled laundry.

■

The machine works more economically if it is fully
loaded.

■

With adequate pre-treatment, stains and limited
soiling can be removed; the laundry can then be
washed at a lower temperature, so saving energy.

In the interest
of the environment

■

Materials marked with the symbol are
recyclable.

■

Check with your local Council or Environmental
Health Office to see if there are facilities in your area
for re-cycling this appliance.

■

When the appliance is to be scrapped, cut off the
power supply cable and make the door lock device
unusable to prevent young children from being
trapped inside.

■

Help to keep your country tidy - use authorised
disposal sites for your old appliance.

How do we help to protect the environment?
We use recycled paper!

Important

Your machine is fitted with a balance control device, which ensures the machine is stable during the spin.
If the wash load appears not to have been spun sufficiently at the end of the wash cycle, because it is not evenly
distributed in the drum, the balance control device may have operated. It will therefore be necessary to redistribute the
wash load manually and select a spin programme. For more detailed information see the section headed "Something
Not Working".

5

Description of the Appliance

1 Detergent dispenser drawer
2 Programme guide
3 “Mains-on” light
4 ON/OFF button
5 “Option” buttons
6 Programme selector dial
7 Door opening handle
8 Filter
9 Adjustable feet

Detergent dispenser drawer

Prewash
Main wash
Fabric softener

1

7

653

2

8

9

4

95
95
60
40

40
40

50
30

COTTONS - LINENS

Pre-wash & Whites
Whites
Fast Coloureds
Non Fast Coloureds
Long spin

WOOL - DELICATES

Wool Wash
Delicates
Drain

SYNTHETICS - MIXED FABRICS

Mixed Fabrics
Quick & Cool Wash
Rinses
Conditioner Rinse
Short spin

MAINSONRINSE

HOLD

1
2
3
4
5

1
1
1

6
7
8
9
10

BIW 1000 W

IMPORTANT: PLEASE READ THE INSTRUCTION BOOK BEFORE USE.

HALF
LOAD

SELECTOR

C0026

1 Programme guide

2 Mains-on light

This light illuminates when the machine starts working
and goes out when the ON/OFF button is released.

3 On/Off button

By depressing this button the machine starts operating.
When depressed again, the machine stops.

4 Rinse Hold button

Press this button to make the machine stop with water in
the drum after the cotton, synthetic or delicate wash
cycles.
This prevents any creasing which may occur if the
clothes are left damp in the drum. When it is convenient
for you to empty the machine, simply press this button
again so that the machine can proceed to drain and spin,
or turn the dial to the drain programme “13”.
If this button is not activated, the washing programmes
will end with a spin.

6

The Control Panel

12345 6

95
95
60
40

40
40

50
30

COTTONS - LINENS

Pre-wash & Whites
Whites
Fast Coloureds
Non Fast Coloureds
Long spin

WOOL - DELICATES

Wool Wash
Delicates
Drain

SYNTHETICS - MIXED FABRICS

Mixed Fabrics
Quick & Cool Wash
Rinses
Conditioner Rinse
Short spin

MAINSONRINSE

HOLD

1
2
3
4
5

1
1
1

6
7
8
9

10

BIW 1000 W

IMPORTANT: PLEASE READ THE INSTRUCTION BOOK BEFORE USE.

HALF
LOAD

SELECTOR

5 HALF LOAD button

Select this button to reduce water consumption on the
rinse cycle when washing a smaller load of cottons or
linens (maximum load size = 2.25 kg).

6 Programme selector dial

Turn the dial clockwise to select the required wash
programme.

Before setting the dial to any position the machine must
be switched off by depressing the ON/OFF button again.

7

Operating Sequence

Before the first wash, we recommend that you run a
cotton cycle at 60°C, without any laundry in the
machine, to remove any manufacturing residue from the
drum and tub.
Pour 1/2 a measure of detergent into the dispenser
drawer and start the machine.

WASHING 4.5 KG OF WHITE COTTON AT 95°C

Suppose you have 4.5 kg of normally dirty laundry to
wash. It is white cotton and is suitable for high
temperature washing.

1. Load the laundry

Open the door by pulling the door handle outwards.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible. Close the door.

2. Measure out the detergent

Pull out the dispenser drawer until it stops.
Measure out the amount of detergent required and pour
it into the main wash compartment .
If you wish to carry out the prewash, pour detergent into
the compartment marked .

C0025

P0004

3. Measure out the fabric
softener

If required, pour fabric softener into the compartment
marked (the amount used must not exceed the
“MAX” mark in the drawer).
Close the drawer gently.

4. Select the required option

Depress RINSE HOLD button, if required.

5. Select the required programme

Turn the programme selector dial clockwise to the
programme 2 or 1 (if you wish to perform a prewash).

P1006S

2

RINSE
HOLD

HALF

LOAD

C0024

8

6. Start the machine

Before starting up the machine check that:

■

the appliance is plugged in

■

the water supply taps are turned on

■

the drain hose is correctly and securely positioned

■

the door and the detergent dispenser drawer are
closed.

Depress the ON/OFF button: the mains-on light will
illuminate and the machine starts operating.

7. At the end of the programme

The machine stops automatically.
If you have depressed the RINSE HOLD button, the

machine will stop with the water left in the tub, to
prevent the fabric from creasing. To drain the water and
spin, release the same button. To drain only, select
programme “13”.

The door is controlled by a safety device which releases
2 minutes after the end of the programme.

Switch the machine off by depressing the ON/OFF
button again. The mains-on light goes out.

When the programme has finished you are advised to
unplug the appliance and turn off the water taps.

T0006S

MAINS

ON

9

WASHING 2.5 KG OF MIXED FABRICS AT 50°C

Suppose you have 2.5 kg of Mixed fabrics to wash.
They are rather delicate fabrics and should not be
washed at a high temperature.

1. Load the laundry

Open the door by pulling the door handle outwards.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible. Close the door.

2. Measure out the detergent

Pull out the dispenser drawer until it stops.
Measure out the amount of detergent required and pour
it into the main wash compartment .

3. Measure out the fabric
softener

If required, pour fabric softener into the compartment
marked (the amount used must not exceed the
“MAX” mark in the drawer).
Close the drawer gently.

C0024

C0025

P0004

4. Select the required option

Depress the RINSE HOLD button if required.

5. Select the required programme

Turn the programme selector dial clockwise to the
programme 6.

6. Start the machine

Before starting up the machine check that:

■

the appliance is plugged in

■

the water supply taps are turned on

■

the drain hose is correctly and securely positioned

■

the door and the detergent dispenser drawer are
closed.

Depress the ON/OFF button: the mains-on light will
illuminate and the machine starts operating.

T0006S

MAINS

ON

M0017S

6

RINSE
HOLD

HALF

LOAD

10

7. At the end of the programme

The machine stops automatically.
If you have depressed the RINSE HOLD button, the

machine will stop with the water left in the tub, to
prevent the fabric from creasing. To drain the water and
spin, release the same button. To drain only, select
programme “13”.

The door is controlled by a safety device which releases
2 minutes after the end of the programme.

Switch the machine off by depressing the ON/OFF
button again. The mains-on light goes out.

When the programme has finished you are advised to
unplug the appliance and turn off the water taps.

11

Washing Hints

Do NOT overload the machine. Weigh the laundry the
first few times you use the appliance.

The average weights of the most common items are
listed below as a guide:

1000g = 1 kg

Sheet 700-1000 g
Pillow case 100-200 g
Tablecloth 400-500 g
Serviette 50-100 g
Tea towel 70-120 g
Linen hand towel 100-150 g
Towelling hand towel 150-250 g
Towelling bath towel 700-1000 g
Bath robe 1000-1500 g
Man’s shirt 200-300 g
Apron 150-200 g

■

Load the laundry loosely alternating large items with
small ones.

■

Sort the laundry according to the type of fabric,
colour-fastness and how dirty it is.

■

Avoid washing unhemmed or torn items as they may
unravel.

■

Before washing, empty all pockets of small objects
which may have been left inside (coins, keys, screws
etc). as these could damage the drain pump.

■

When washing curtains, remove the hooks.

■

Close poppers and zips and fasten loose buttons.

■

It is essential to wash new coloured items separately
when washing for the first time.

■

When washing fabrics requiring different wash
temperatures together, always select the lowest
temperature.

■

White items should not be washed with coloured
items.

■

Very small items (handkerchiefs, ribbons, socks etc)
should be washed in a washing bag or a pillow case.

■

Use a good quality detergent suitable for automatic
washing machines.

■

Use the correct quantities of detergent.

■

For wool, use gentle detergent only in small
quantities.

■

Bleach is very corrosive; it should be used with care
and kept out of reach of children.

■

Some stains such as fruit, wine, grass, rust etc. are
difficult to remove and should be treated before
washing with specific products, which can be found
in most household shops. In some cases it may help
to soak the stain before washing with a special pre­soak product or biological detergent.

■

Only wool marked “Pure New Wool - washable,
preshrunk” can be washed in the machine using the
wool programme; other types of wool should be
washed by hand or dry cleaned.

■

If you have used the machine to wash, rinse or spin
only non-colour fast garments, there may be dye left
in the sump. To ensure any subsequent wash is not
contaminated with the dye, select and carry out a
rinse and spin programme, without any garments, to
ensure that any dye is removed from the sump.

■

Once you have finished using the machine, you are
advised to unplug it and turn off the water taps.

12

And in which form?

Not only are there different types of detergent, but they
are also available in different forms. Whether you chose
a powder or liquid in traditional or compact form is
your own personal choice.

TRADITIONAL POWDERS

Pour the powder directly into the dispenser drawer. Do
not sprinkle powder onto clothes in the machine drum.

TRADITIONAL LIQUIDS

Liquid can be placed in the main wash compartment of
the detergent drawer marked with the symbol , start
the machine immediately upon placing the detergent in
the dispenser drawer.
Alternatively the detergent is measured into the
specially designed dosing device* which should be
placed on top of the laundry, and at the back of the
machine drum.

COMPACT POWDERS AND LIQUIDS

Compact detergents (or concentrates as they are also
known) are available in liquid or powder form, and
generally require a smaller dosage. Follow the
manufacturer’s instructions to ensure the most
economical usage. Pour the detergent directly into the
dispenser drawer, or alternatively measure the detergent
into the specially designed dosing device* which
should be placed on top of the laundry, and at the back
of the machine drum.

* If you use a dosing device in a washer dryer,

please ensure the dosing device/ball is removed
before carrying out a drying programme.

FABRIC CONDITIONERS

These are ideal for improving ‘softness’, and also
reduce static cling on synthetics and make ironing
easier. They are available in two types:

For example Lenor liquid fabric
softener, for use in the washing
machine/washer dryer. The
liquid fabric softener should be
poured into the compartment
marked with the symbol .
Follow the manufacturer’s dosage
instructions and never exceed the
MAX level.

Bounce conditioning sheets for use
in a tumble dryer. We recommend
the conditioning sheets are pinned
(using a safety pin) to an article
of laundry and placed in the
tumble dryer.

Which detergent?....

To ensure you obtain the best wash results from your
appliance, it is important to use the right detergent in
your everyday wash, and only detergents recommended
for use in automatic machines.
To maintain the appearance of your clothes and
household textiles and to make them last longer you
should use different types of detergent for different
washes, whether for whites, colours or delicates.

WHITES

We recommend the Ariel product
range which is biological and
designed to provide excellent
cleaning and stain removal even
at low temperatures.

NON BIOLOGICAL

If you prefer to use a non
biological detergent, which does
not contain enzymes we
recommend Fairy. Fairy provides
good cleaning and stain removal.

COLOUREDS

For coloured items you should use a
detergent which is designed to clean
while maintaining the original colour.
Ariel Color does not contain bleach
and therefore helps to preserve
colours.

DELICATE ITEMS

When washing delicates such as
woollens, you should use a product
which is specially designed to care for
fine fabrics.
Dreft Automatic is suitable for
woollens and other delicates.

LAUNDRY BLEACH

For additional stain removal you may
wish to use a product such as Ace
Gentle Bleach which is used in addition
to your chosen detergent. Ace is
suitable for all washable fabrics
including silks, woollens and coloureds.

13

Wash Care Symbols

Wash care labels inside garments recommend how to launder your clothes with the best results. The care labelling
code is in line with care labelling used in the rest of Europe. The symbols used make it easy to select the correct
programme on your washing machine.

WASHING SYMBOL

BLEACHING

IRONING

DRY CLEANING

TUMBLE DRYING

WASH ACTION FABRIC

Hot iron

Warm iron

Cool iron

Cotton, Linen, Viscose

Polyester mixtures, Wool

Acrylic, Nylon, Polyester

Important Notes

For best results, always use the dispenser drawer for
dispensing detergents and liquid additives.
Once the dispenser has been filled, close it by pushing it
in gently. This is particularly important if you are using

fabric conditioner to avoid the conditioner entering the
machine prematurely.
When using liquid detergent and a prewash programme,
place the detergent into the correct compartment in the
dispenser drawer, after the prewash has finished.

95

60

50

40

40

40

Chlorine bleach may be used

May be tumble dried

with high heat setting

with low heat setting

A cross through any symbol means «DO NOT»

May be dry cleaned. Other letters and/or a bar beneath the circle will
indicate the required process to the dry cleaner.

Normal (Maximum)

Normal (Maximum)

White Cotton or Linen
without Special Finishes

Cotton, Linen or Viscose
without Special Finishes
Colourfast at 60°C.

Reduced (Medium)

Normal (Maximum)

Reduced (Medium)

Much Reduced (Minimum)

Hand wash only

Nylon, Polyester/Cotton, Viscose
with Special Finishes,
Cotton/Acrylic Mix.

Cotton, Linen or Viscose
Colourfast at 40°C but not 60°C.

Acrylics, Acetate, Triacetate, Wool
mixes, Polyester/wool blends.

Wool, wool mixtures, Silks

Do not machine wash

X

14

Washing Programmes

Degree of soil

and type of laundry

Description

Wash programme/

Washing symbol

Programme

dial position

Possible

options

Max.

load

NON- FAST

COLOUREDS

F AST

COLOUREDS

WHITES

PREWASH

&

WHITES

For heavy soiled cotton
items.

Fast coloured cotton or
linen fabrics, shirts,
underwear, towels.

Non fast coloured
cotton or linen fabrics,
shirts, blouses,
underwear.

White cotton, for
example normally soiled
work garments, sheets,
household linen,
underwear, towels.

1

4

3(*)

2

Wash at 95 °C
3 rinses
Long spin

Wash at 60 °C
3 rinses
Long spin

Wash at 40 °C
3 rinses
Long spin

Prewash at 40 °C
Wash at 95°C
3 rinses
Long spin

RINSE

HOLD

HALF

LOAD

RINSE

HOLD

HALF

LOAD

RINSE

HOLD

HALF

LOAD

RINSE

HOLD

HALF

LOAD

4.5 kg

4.5 kg

Progr.

time

mins.

115

105

12

155

130

4.5 kg

4.5 kg

LONG SPIN

Separate spin for
cotton and linen items

5

Long spin

4.5 kg

(*) This programme at 60°C is the reference programme for the Energy label according to EEC Directive 92/75.
Water filling: 30°-40° programmes: cold water filling

50°-60°-95° programme: hot and cold filling

The programme times are intended as a guide only. The actual time will vary depending on incoming water
temperature and pressure.

Programmes for cotton and linen

15

Washing Programmes

Degree of soil

and type of laundry

Description

Wash programme/

Washing symbol

Programme
dial position

MIXED

F ABRICS

Possible

options

SHORT
SPIN

WOOL WASH

DELICATES

Synthetic or mixed
fabrics, underwear,
coloured garments,
non-shrink shirts,
blouses.

Specially tested
programme for wool
garments bearing the
“Pure new wool, non­shrink, machine
washable” label.

Delicate fabrics, for
example curtains

6

7

11

12

Wash at 40 °C
3 rinses
Short spin

Wash at 40 °C
3 rinses
Short spin

Wash at 30 °C
3 rinses
Short spin

Wash at 50 °C
3 rinses
Short spin

DRAIN

CONDITIONER

RINSE

QUICK

&

COOL WASH

Lightly soiled synthetic
or mixed fabrics

This programme can be
used for softening hand
washed garments.

Separate spin for
synthetics and delicates

For emptying out the
last rinse water in
programmes with the
Rinse Hold option.

13

10

9

Draining of water
and short spin

1 rinse, with fabric
softener, if required
Short spin

Draining of water

Programmes for synthetics, mixed fabrics, delicates and wool

Max.

load

Progr.

time

mins.

2.5 kg

2.5 kg

2 kg

2.5 kg

2.5 kg

2.5 kg

-

RINSE
HOLD

RINSE
HOLD

RINSE
HOLD

RINSE
HOLD

60

50

50

35

9

5

1

RINSES

Separate rinse cycle for
hand washed items

8

3 rinses, with fabric
softener, if required
Short spin

2.5 kg 20

RINSE
HOLD

RINSE
HOLD

16

Maintenance and Cleaning

Before any maintenance or cleaning is carried out you
must DISCONNECT the appliance from the electricity
supply .

Descaling

The water we use normally contains lime. It is a good
idea to periodically use a water softening powder in the
machine. Do this separately from any laundry washing,
and according to the softening powder manufacturer's
instructions. This will help to prevent the formation of
lime deposits.

After each wash

Leave the door open for a while. This helps to prevent
mould and stagnant smells forming inside the appliance.
Keeping the door open after a wash will also help to
preserve the door seal.

External cleaning

Clean the exterior cabinet of the appliance with soap
and water only, and then dry thoroughly.

Cleaning the dispenser drawer

From time to time the washing powder and additive
dispenser drawer should be cleaned.
Remove the drawer by pressing the catch downwards
and by pulling it out. Flush it out under a tap, to remove
any traces of accumulated powder.
To aid cleaning, the top part of the additive
compartment should be removed.

C0027

C0023

Cleaning the drawer recess

Having removed the drawer, use a small brush to clean
the recess, ensuring that all washing powder residue is
removed from the upper and lower part of the recess.
Replace the drawer and run the rinse programme
without any clothes in the drum.

Cleaning the filter

The water drain filter

A clean filter is important for the correct operating of
the machine, and should therefore be cleaned after every
washing programme.

Open the filter door and place a container underneath to
catch any spillage. If the filter is blocked and the
machine is unable to drain you will need to drain the
water manually from the machine at this stage. To do
this, unhook the drain hose from the standpipe or sink
and hold the end of the hose over a bowl on the floor.
The water should drain by gravity into the bowl. When
the bowl is full, hook the hose back up and empty the
bowl. Repeat the procedure until water stops flowing
out.

P0132

P0011

P0038

17

Unscrew and remove the filter.
Clean carefully under a fast running tap.

Warning

When the appliance is in use and depending on the
programme selected there can be hot water in the filter.
Never remove the filter during a wash cycle, always
wait until the appliance has finished the cycle, and is
empty. When replacing the filter, ensure it is securely
retightened so as to stop leaks and young children being
able to remove it.

The water inlet filters

If your water is very hard or contains traces of lime
deposit, the water inlet filters may become clogged.

It is therefore a good idea to clean them from time to
time.

Turn off the water taps. Unscrew the water inlet hoses.
Clean the filters using a hard bristle brush.

Tighten up the inlet hoses.

P1090

P0040

P0133

The dangers of freezing

If the machine is exposed to temperatures below 0°C,
certain precautions should be taken.

■

Turn off the water taps.

■

Unscrew the inlet hoses.

■

Unhook the drain hose from the rear support and
position the end of this hose and that of the inlet
hoses in a bowl. Run the draining programme.

■

Disconnect the appliance.

■

Screw the inlet hoses and reposition the drain hose.

■

When you intend to start the machine up again,
make sure that the room temperature is above 0°C.

Maintenance Wash

With the use of low temperature washes it is possible to
get a build up of residues inside the drum.
We recommend that a maintenance wash be performed
on a regular basis.

To run a maintenance wash:

■

The drum should be empty of laundry.

■

Select the hottest cotton wash programme.

■

Use a normal measure of detergent, must be a
powder (such as Ariel Futur).

18

Something Not Working

Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out
an engineer. Before contacting your local Electrolux Service Force Centre, please carry out the checks listed below.

IMPORTANT: if you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation, a charge will be made even if the appliance is under guarantee.

Symptom

The machine does not start

Possible causes

■

The door has not been closed.

■

The plug is not properly inserted in the power socket.

■

There is no supply at the socket

■

The main fuse or the fuse in the plug has blown.

■

The selector dial is not correctly positioned.

■

The ON/OFF button has not been depressed.

The machine does not fill

■

Ensure the water taps are open.

■

The filters in the inlet hoses are blocked.

■

The inlet hoses may be squashed or kinked.

■

The door has not been closed.

The machine fills then empties
immediately

■

The end of the drain hose is too low.

■

The end of the drain hose is submerged in water.

■

There is no vent in the end of the drain hose.

The machine does not empty and/or
does not spin

■

The drain hose may be squashed or kinked.

■

The RINSE HOLD option has been selected.

■

The drain filter may be blocked.

■

The drain hose extension, if fitted, is not correct. Follow the
instructions for connecting to the waste.

■

The drainage system pipes are blocked.

■

The wash load is unbalanced: redistribute the clothes inside the drum to
allow the machine to spin.

There is water on the floor

■

Too much detergent or unsuitable detergent has been used (creates too
much foam).

■

Check whether there are any leaks from one of the inlet hose(s) fittings.
It is not always easy to see this as the water runs down the hose; check
to see if it is damp.

■

The drain hose may be damaged or not securely positioned.

■

The detergent dispenser drawer or recess is clogged.

■

The drainage system pipes are blocked.

Unsatisfactory washing results

■

Too little detergent or unsuitable detergent has been used. An
insufficient amount of detergent leaves the laundry looking grey and
causes lime scale to form.

■

Stubborn stains have not been treated prior to washing

■

The correct wash programme has not been selected.

■

Too much laundry has been placed in the drum.

The machine vibrates when spinning

■

The internal packing has not been removed.

■

The machine is in contact with the wall or furniture.

■

The machine is not stable and level (check diagonally).

■

The washing load is badly distributed in the drum.

■

Maybe there is very little laundry in the drum.

19

Symptom

The door will not open

Possible causes

■

The programme is still running.

■

The door lock has not yet released.

■

Water in the tub: the door cannot be opened if water is present in the
tub.

Spinning starts late or the machine
does not spin

■

The electronic unbalance detection device has cut in because the
laundry is not evenly distributed in the drum. The laundry is
redistributed by reverse rotation of the drum. This may happen several
times before the unbalance disappears and normal spinning can resume.
If, after 10 minutes, the laundry is still not evenly distributed in the
drum, the machine will not spin. In this case, redistribute the load
manually and reselect the spin programme.

The machine makes an unusual
noise

■

The machine is fitted with a type of motor which makes an unusual
noise compared with other traditional motors. This new motor ensures
a softer start and more even distribution of the laundry in the drum
when spinning, as well as increased stability of the machine.

No water is visible in the drum

■

Machines based on modern technology operate very economically
using very little water without affecting performance.

If after the above checks, there is still a fault, call your
local Electrolux Service Force Centre.

Service & Spare Parts

If you require an engineer or wish to purchase spare
parts contact your local Electrolux Service Force Centre
by telephoning:

0870 5 929929

Your telephone call will be routed to the Service Centre
covering your post code area.
The addresses are detailed in this instruction book on
the pages headed Electrolux Service Force Centres, and
can also be found in your local telephone directory
under “E”.
When you call the Service Force Centre please make
sure you give the model and serial number of the
appliance.

This information can be found on the rating plate (see
picture) or on the guarantee card.

Mod. ..........

Prod. No. ...........

Ser. No. .........

M

o

d

. ...

.......

P

r

o

d

. N

o

.

....

.......

S

e

r. N

o

. ..

.....

..

P0042

CUSTOMER CARE

For general enquiries concerning your Electrolux
appliance or for further information on Electrolux
products, please contact our Customer Care Department
by letter or telephone as follows:

Customer Care Department
Electrolux
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel [phone]*

* calls to this number may be recorded for training

purposes.

20

Guarantee Conditions

Standard guarantee conditions

We, Electrolux undertake that if, within 12 months of
the date of the purchase, this Electrolux appliance or any
part thereof is proved to be defective by reason only of
faulty workmanship or materials, we will, at our option,
repair or replace the same FREE OF ANY CHARGE
for labour, materials or carriage on condition that:

■

The appliance has been correctly installed and used
only on the electricity supply stated on the rating
plate.

■

The appliance has been used for normal domestic
purposes only, and in accordance with the
manufacturer’s instructions.

■

The appliance has not been serviced, maintained,
repaired, taken apart or tampered with, by any
person not authorised by us.

All service work under this guarantee must be
undertaken by an Electrolux Service Force Centre.

Any appliance or defective part replaced shall become
the Company’s property.

This guarantee is in addition to your statutory and other
legal rights.

Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.

Exclusions

This guarantee does not cover:

■

Damage or calls resulting from transportation,
improper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.

■

Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliances
outside the United Kingdom.

■

Appliances found to be in use within a commercial
environment, plus those which are subject to rental
agreements.

■

Products of Electrolux manufacture which are NOT
marketed by Electrolux.

European guarantee

If you should move to another country within Europe
then your guarantee moves with you to your new home
subject to the following qualifications:

■

The guarantee starts from the date you first
purchased your product.

■

The guarantee is for the same period and to the same
extent for labour and parts as exists in the new
country of use for this brand or range of products.

■

The guarantee relates to you and cannot be
transferred to another user.

■

Your new home is within the European Community
(EC) or European Free Trade Area.

■

The product is installed and used in accordance with
our instructions and is only used domestically, i.e. a
normal household.

■

The product is installed taking into account
regulations in your new country.

Before you move please contact your nearest Customer
Care Centre, listed below, to give them details of your
new home. They will then ensure that the local Service
Organisation is aware of your move and able to look
after you and your appliances.

France Senlis [phone]
Germany Nurnberg [phone]
Italy Pordenone [phone]
Sweden Stockholm [phone]
UK Slough [phone]

21

Electrolux Service Force

To contact your local Bendix Service Centre telephone [phone]

CHANNEL ISLANDS

GUERNSEY

Guernsey Electricity
PO Box 4
Vale, Guernsey
Channel Islands

JERSEY

Jersey Electricity Company
PO Box 45
Queens Road
St Helier
Jersey
Channel Islands JE4 8NY

SCOTLAND

ABERDEEN

54 Claremont Street

(M05)

Aberdeen AB10 6RA

AUCHTERMUCHY

33a Burnside

(M03)

Auchtermuchy
Fife KY14 7AJ

BLANTYRE

Unit 5

(M07)

Block 2
Auchenraith Ind. Estate
Rosendale Way
Blantyre G72 0NJ

DUMFRIES

93 Irish Street

(M01)

Dumfries
Scotland DG1 2 PQ

DUNOON

Brair Hill

(M67)

7 Hill Street
Dunoon
Argyll PA23 7AL

GLASGOW

20 Cunningham Road

(M04)

Clyde Estate
Rutherglen
Glasgow G73 1PP

INVERNESS

Unit 3B

(M06)

Smithton Ind. Estate
Smithton
Inverness IV1 AJ

ISLE OF ARRAN

Arran D omestics
Unit 4 The Douglas Centre
Brodick

(OWN SALES)

Isle of Arran KA27 8AJ

ISLE OF BARRA

JZerfah
244 Bruernish
Isle of Barra

(OWN SALES)

Western Islands HS9 5QY

ISLES OF BUTE

Walker Engineering
Glenmhor
Upper Serpentine Road
Rothesay
Isle of Bute PA20 9EH

ISLE OF LEWIS

ND Macleod
16 James Street
Stornoway
Isle of Lewis PA87 2QW

KELSO

2-8 Wood Market

(M08)

Kelso
Borders TD5 7AX

ORKNEY

Corsie Domestics

(M65)

7KingStreet
Kirkwall
Orkney KW15

PERTH

Hydro Electrical
Inveralmond House
Ruthervenfield Road
Perth PH1 3AQ

PERTH

Graham Begg
Unit 4
Airport Ind Estate

(OWN SALES)

Wick KW1 4QS

SHETLAND

Tait Electronic Systems Ltd
Holmsgarth Road
Lerwick

(OWN SALES)

Shetland ZE1 0PW

SHETLAND

Bolts Shetland Ltd.
26 North Road
Lerwick

(OWN SALES)

Shetland ZE1 0PE

WHALSAY

Leask Electrical
Harisdale
Symbister, Whalsay

(OWN SALES)

Shetland ZE2 9AA

NORTHERN IRELAND

BELFAST

Owenmore House

(M27)

Kilwee Business Park
Upper Dunmury Lane
Belfast
BT17 0HD

WALES

CARDIFF

Guardian Industrial Estate

(M28)

Clydesmuir Road
Tremorfa
Cardiff
CF2 2QS

CLYWD

Unit 6-7 Coed  Parc

(M14)

Abergele Road
Rhuddlan
Clwyd
Wales
LL18 5UG

DYFED

Maes Y Coed

(M77)

High Mead
Llanybydder
Carmarthenshire
SA40 9UL

HAVERFORDWEST

Cromlech Lodge

(M75)

Ambleston
Haverfordwest
Pembrokeshire
SA62 5DS

OSWESTRY

Plas Ffynnon

(M17)

Warehouse
Middleton Road
Oswestry
SY11 2PP

NORTH EAST

GATESHEAD

Unit 356a

(M39)

Dukesway Court
Dukesway
Team Valley
Gateshead NE11 0BH

GRIMSBY

15 Hainton Avenue

(M42)

Grimsby
South Humberside
DN32 9AS

HULL

Unit 1

(M41)

Boulevard Industrial Estate
Hull
HU3 4AY

LEEDS

64-66 Cross Gates Road

(M37)

Leeds
LS15 7NN

NEWTON AYCLIFFE

Unit 16

(M45)

Gurney Way
Aycliffe Industrial Estate
Newton Aycliffe
DL5 6UJ

SHEFFIELD

Pennine House

(M38)

Roman Ridge Ind.
Roman Ridge Road
Sheffield S9 1GB

NORTH WEST

BIRKENHEAD

1 Kelvin Park

(M11)

Dock Road
Birkenhead
L41 1LT

CARLISLE

Unit 7

(M10)

James Street Workshops
James Street
Carlisle
Cumbria CA2 5AH

ISLE OF MAN

South Quay Ind. Estate

(M64)

Douglas
Isle of Man
IM1 5AT

LIVERPOOL

Unit 1

(M15)

Honeys Green Precinct
Honeys Green Lane
Liverpool
L12 9JH

MANCHESTER

Unit B

(M09)

Central Industrial Estate
St Marks Street
Bolton
BL3 6NR

PRESTON

Unit 250

(M13)

Dawson Place
Walton Summit
Bamber Bridge
Preston
Lancashire PR5 8AL

STOCKPORT

Unit 20 Haigh Park

(M16)

Haigh Avenue
Stockport
SK4 1QR

22

Electrolux Service Force

To contact your local Bendix Service Centre telephone

08705 929 929

MIDLANDS

BIRMINGHAM

66 Birch Road East

(M18)

Wyrley Road Ind. Estate
Witton
Birmingham
B6 6DB

BOURNE

Manning Road Ind. Estate

(M44)

Pinfold Road
Bourne
PE10 9HT

BRIDGNORTH

68 St. Marys Street

(M72)

Bridgnorth
Shropshire
WV16 4DR

GLOUCESTER

101 Rycroft Street

(M23)

Gloucester
GL1 4NB

HEREFORD

Unit 3

(M31)

Bank Buildings
Cattle market
Hareford
HE4 9HX

HIGHAM FERRERS

30 High Street

(M51)

Higham Ferrers
Northants
NN10 8BB

ILKESTON

Unit 2

(M43)

Furnace Road
Ilkeston DE7 5EP

LEICESTER

Unit 7

(M22)

Oaks Ind. Estate
Coventry Road
Narborough
Leicestershire
LE0 5GF

LINCOLN

Unit 8

(M40

) Stonefield Park

Clifton Street
Lincoln
LN5 8AA

NEWCASTLE

18-21 Croft Road

UNDER LYME

Brampton Ind. Estate

(M12)

Newcastle under Lyme
Staffordshire
ST5 0TW

REDDITCH

13 Thornhill Road

(M20)

North Moons Moat
Redditch
Worcestershire
B98 9ND

TAMWORTH

Unit 3

(M19)

Sterling Park
Claymore
Tamworth
B77 5DO

WORCESTER

Units 1 & 2

(M73)

Northbrook Close
Gregorys Mill Ind. Estate
Worcester
WR3 8BP

LONDON & EAST ANGLIA

BECKENHAM

11a Gardener Ind. Estate

(M79)

Kent H ouse Lane
Beckenham
Kent BR3 1QZ

CHELMSFORD

Hanbury Road

(M47)

Widford Ind. Estate
Chelmsford
Essex
CM12 3AE

COLINDALE

Unit 14

(M53)

Capitol Park
Capitol Way
Colindale
London NW9 0EQ

ELTHAM

194 Court Road

(M78)

Mottingham
Eltham
London SE9 4EW

ENFIELD

284 Alma Road

(M49)

Enfield
London
EN3 7BB

GRAVESEND

Unit B4

(M57)

Imperial Business Estate
Gravesend
Kent
DA11 0DL

HARPENDEN

Unit 4

(M46)

Riverside Estate
Coldharbour Lane
Harpenden
AL5 4UN

LETCHWORTH

16-17 Woodside Ind. Estate

(M50)

Works Road
Letchworth
Herts
SG6 1LA

LONDON

2/4 Royal Lane

(M76)

Yiewsley
West Drayton
Middlesex
UB7 8DL

MAIDENHEAD

Reform Road

(M60)

Maidenhead
Berkshire
SL6 8BY

MOLESEY

10 Island Farm Avenue

(M61)

West Molesey
Surrey
KT8 2UZ

NEWBURY

9PipersCourt

(M24)

Berkshire Drive
Thatcham
Berkshire
RG19 4ER

IPSWICH

Unit 6C

(M48

) Elton Park Business Centre

Hadleigh Road
Ipswich
IP2 0DD

NORWICH

2b Trafalgar Street

(M52)

Norwich
NR1 3HN

SUNBURY

Unit 1a

(M63)

The Summit
Hanworth Road
Hanworth Ind. Estate
Sunbury on Thames
TW16 5D

SOUTH EAST

ASHFORD

Unit 2

(M58)

Bridge Road Business Est.
Bridge Road
Ashford
Kent TN2 1BB

FLEET

Unit 1

(M59)

Redsfield Ind. Estate
Church Crookham
Fleet
Hampshire GU13 0RD

HAYWARDS

21-25 Bridge Road

HEATH

Haywards Heath

(M55)

Sussex RH16 1UA

SOUTH WEST

BARNSTAPLE

Main Road

(M30)

Fremington
Barnstaple
North Devon EX31 2NT

BOURNEMOUTH

63-65 Curzon Road

(M26)

Bournemouth
Dorset
BH1 4PW

BRIDGEWATER

6 Hamp Ind. Estate

(M35)

Bridgewater
Somerset TA6 3NT

BRISTOL

11 Eldon Way

(M25)

Eldonwall Trading
Bristol
Avon BS4 3QQ

EMSWORTH

266 Main Road

(M33)

Southbourne
Emsworth
PO10 8JL

ISLE OF WIGHT

Unit 8

(M34)

Enterprise Court
Ryde Business Park
Ryde
Isle of Wight PO33 1DB

NEWTON ABBOT

Unit 2

(M29)

Zealley Ind. Estate
Kingsteignton
Newton Abbot
S. Devon
TQ12 3TD

REDRUTH

Unit 7D

(M36

) Pool Ind. Estate

Wilson Way
Redruth
Cornwall TR15 3QW

23

Installation Instructions

Technical Specifications

It is dangerous to alter the specifications or

attempt to modify this product in any way.

Care must be taken to ensure that the appliance

does not stand on the electrical supply cable.

Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.

Any plumbing work required to install this
appliance should be carried out by a qualified
plumber or competent person.

DIMENSIONS Height 85 cm (33.5”)

Width 60 cm (23.6”)
Depth 58 cm (22.7”)

POWER SUPPLY VOLTAGE 230-240 V/50 Hz
TOTAL POWER ABSORBED 2050 W (10A)

Minimum (hot) 0.35 bar (3.5 N/cm

2

)

WATER PRESSURE Minimum 0.48 bar (4.8 N/cm

2

)

Maximum 7.6 bar (76 N/cm2)

MAXIMUM RECOMMENDED LOAD Cotton, linen 4.5 kg (10 lbs)

Synthetics 2.5 kg (5 lbs)
Delicate fabrics 2.5 kg (5 lbs)
Wool 2 kg (4.5 lbs)

SPIN SPEED Maximum 1000 rpm (BIW 1000W)

1200 rpm (BIW 1200W)

CONSUMPTION DATA FOR WASHING Energy 1.03 kWh

4.5 KG NORMALLY SOILED COTTON Water 54 litres
ITEMS AT 60°C (PROGR. 3) WITH COLD
WATER FILLING

This appliance complies with the following E.E.C. Directives:

- 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications;

- 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.

24

Unpacking

All transit bolts and packing must be removed

before using the appliance.

You are advised to keep all the packaging for re-use in
case the machine is to be transported again.

Using a spanner unscrew and remove the rear right bolt.
Lay the machine gently on its back, making sure that the
hoses are not squashed.

Remove the polystyrene block from the bottom of the
machine.
Carefully slide out the right polythene bag (1).

Repeat the operation for the left polythene bag (2).

Remove the polystyrene base.
Set the machine upright and remove the two remaining
bolts from the back.
Pull out the three plastic spacers from the holes into
which the bolts were fitted.
Plug all the holes with the plugs which you can find in
the envelope containing the instruction booklet.

P0020

P0256

2

1

P1066

P1068

P0255

Positioning

Install the machine on a flat hard floor.
Make sure that air circulation around the machine is not
impeded by carpets, rugs etc. Check that the machine
does not touch the wall or other kitchen units.
Never place cardboard, wood or similar materials under
the machine to compensate for any unevenness in the
floor.

Your new washing machine has been designed to be
permanently plumbed in to your home’s water supply
and drainage system. However, if this is not possible, it
may be connected to suitable existing taps with the drain
hose discharging into a sink.
The appliance has two inlet hoses, hot and cold, with
female 3/4” BSP thread connectors. If this connection is
not compatible with the plumbing of the existing
installation, a variety of connectors are available from
good hardware stores and plumbers merchants to suit
most domestic plumbing. Any alteration to your existing
plumbing must be carried out by a competent person, or
qualified plumber.

Installation on a Suspended Floor

Suspended wooden floors are particularly susceptible to
vibration. To help prevent vibration we recommend you
place a waterproof wood panel, at least 15 mm thick
under the appliance, secured to at least 2 floor beams
with screws. If possible install the appliance in one of
the corners of the room, where the floor is more stable.

Water inlet

The inlets on the back of the appliance are colour coded,
blue for cold and red for hot.

Connect the hoses to taps with ¾” thread.

P1088

25

If only a cold water supply is available, connect the two
hoses to a cold water outlet by means of a «Y»
connection piece.

Installation should comply with local water authority
and building regulations’ requirements.

The appliance must be given a separate cold water
supply and not be connected to a mixer tap, a single
outlet water heater or a booster pump. A minimum
water pressure of 0.48 bar is required for safe operation
of the appliance.

If you cannot make the cold water connection direct
from the rising mains, you may be able to operate the
appliance from your cold water storage system.

There should be a minimum distance of 5.02m
(16.5 ft) between the appliance’s inlet and the bottom of
the water storage tank.

There will be sufficient pressure for the hot water
supply, providing there is a minimun height of 2.74
metres (9 ft) between the bottom of the cold water
storage tank and the bottom of the hot water cylinder.

Set the hoses correctly by loosening the ring nuts. After
positioning the inlet hoses, be sure to tighten the ring
nuts again to prevent leaks.

Water drainage

This appliance is designed to be permanently plumbed
into your home's water supply and drainage system.

The appliance drain hose should hook into a standpipe,
the hook in the drain hose is formed using the plastic
“U-Piece” supplied.

The standpipe should have an internal diameter of
approximately 38mm (see diagram) thus ensuring there
is an air break between the drain hose and standpipe.

P1040

Min. 30 cm.(12")

38 mm.(1/ ") diameter
standpipe

1

2

P0021

When discharging into a standpipe ensure that the top of
the curve in the hose end is no more than 90cm (35.4'')
and no less than 60cm (23.6'') above floor level. The
upright standpipe should have a minimum length of
30cm (12'') from the bottom of the elbow to the top of
the pipe (see diagram).
Make sure that it is designed in such a way, that the end
of the drain hose cannot be covered with water.

The drain hose may be extended to a maximum of 4
metres. An additional drain hose and joining piece
is available from your local Service Force Centre.
The joining piece must have an internal diameter of
18mm.

If you intend the drain hose to empty into a sink, make
sure that the sink is empty and the plug hole is not
blocked. Use the plastic “U-Piece” supplied.

Important

Before connecting up the machine to new pipework or
to pipework that has not been used for some time, run
off a reasonable amount of water to flush out any debris
that may have collected in the pipes.

P0022

P1039

3 pin

Max. 90 cm.(35.4")

Min.60 cm.

(23.6")

26

Levelling

Level the washing machine by raising or lowering the
feet. The feet may be tight to adjust as they incorporate
a self locking nut, but the machine MUST be level and
stable.

Any necessary adjustment can be made with a spanner.
Accurate levelling prevents vibration, noise and
displacement of the machine during operation.

Some vibration is inevitable, especially if mounted on a
wooden floor.

Sprung wooden floors are particularly susceptible to
vibration. For advice, consult a builder. If possible,
always place the machine on a solid floor.

Special conditions

If the floor is carpeted or covered with crumbly or soft
material, insert a rigid support base under the feet to
prevent noise, vibration or displacement. The base
should protrude a few centimetres beyond the edges of
the machine.

Warning

The machine should NOT be placed on deep pile

carpeting.

Note

Please ensure that when the appliance is installed it is
easily accessible for the engineer in the event of a
breakdown.

P1051

In the interest of the
environment

Washing machines and dishwashers should be
connected to the FOUL drainage system, the water will
then be taken to a sewage works for treatment before
being discharged safely into a river.
It is essential that these appliances are not connected to
the surface water drainage system as this water is
discharged directly into a river or stream and may cause
pollution.
If you require any further advice please contact your
local water authority drainage department.

SHOWER

BATH

SINK TOILET

BIDET

WASHING
MACHINE

DISHWASHER

RAINWATER

'RUN-OFF'

SURFACE WATER

DRAINS & SEWERS

UNTREATED
DISCHARGE

RIVER

FOUL DRAIN

FOUL SEWERS

SEWAGE

TREATMENT

WORKS

RIVER

P0987

TREATED

DISCHARGE

27

Electrical connection

Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.

WARNING: THIS APPLIANCE MUST BE
EARTHED.

The manufacturer declines any liability should

this safety measure not be observed.

Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance’s
rating plate. The rating plate is located at the top of the
rim of the open door.

The appliance is supplied with a 13amp plug fitted.
In the event of having to change the fuse in the plug
supplied, a 13amp ASTA approved (BS1363A) fuse
must be used.
Should the plug need to be replaced for any reason,
proceed as described below.
The wires in the mains lead are coloured in accordance
with the following code:

Green and Yellow - Earth
Blue - Neutral
Brown - Live

The wire coloured green and yellow must be connected
to the terminal marked with the letter «E» or by the
earth symbol or coloured green and yellow.

The wire coloured blue must be connected to the
terminal marked «N» or coloured black.

GREEN & YELLOW

BROWN

CORD CLAMP

BLUE

13A

P1041

E

N

L

Mod. ..........

Prod. No. ...........

Ser. No. .........

M

o

d

.

...

...

...

.

P

ro

d

.

N

o

. .

...

..

...

..

Se

r

.

N

o

.

..

...

..

..

P0042

The wire coloured brown must be connected to the
terminal marked «L» or coloured red.
Upon completion there must be no cut, or stray strands
of wire present and the cord clamp must be secure over
the outer sheath.

WARNING:

A cut off plug inserted into a 13 amp socket is

a serious safety (shock) hazard.
Ensure that the cut off plug is disposed of
safely.

Note

When the appliance is installed the power supply cable
must be accessible.

Permanent connection

In the case of permanent connection it is necessary that
you install a double pole switch between the appliance
and the electricity supply (mains), with a minimum gap
of 3mm between the switch contacts and of a type
suitable for the required load in compliance with the
current electrical regulations.

The switch must not break the yellow and green earth
cable at any point.

Electrolux, 55-77High Street, Slough, Berkshire SL1 1DZ

Consumer care telephone number 08705 950950

© Electrolux Household Appliances Limited 2000