Beltronics Sti r Plus User Manual
Inst allat ion Manua l
Important Notes
•
S A F E T Y D E T E C T O R
•
L A S E R
D I G I T A L R A D A R
Read This First
Please read both sides of these
instructions before starting your
installation.
Important Installation
Warnings
1 A professional installer must
install your new STi-R.
Installation of this system requires
experience and expertise in
automotive electronics. Car Audio
3 If your vehicle is damaged
during installation, its safety
systems may be compromised,
which could cause personal injury
or property damage.
specialists and many car dealers
can install STi-R for you.
4 Improper installation may void
STi-R’s warranty.
2 Attempting to install this
product without expertise in
automotive electronics
installation can cause personal
injury, or damage to your vehicle.
STi-R Comes Complete
Front Radar Receiver
• Weather-proof Front Radar and
Laser Receiver
• Mounting bracket with stainless
steel hardware
• Built-in 6 foot shielded cable with water
proof connector
• 13 foot shielded cable with in-line
waterproof connector
• Wire ties to secure cable
Miniature Controller
• Controller mounts easily to console for
easy to reach access
Miniature Display
• Miniature Display easily mounts to
instrument pod, dashboard or console
• In-Dash trim bezel allows custom in-dash
installation
Interface
• Central module connects to switched
12-volt power and ground
• All components plug directly in using
modular connections
• 3M connector taps into existing vehicle
wiring
Documentation
• Comprehensive Owner’s Manual
• Installation Manual
Built-in Diagnostics
• Confirms all components are operational
Performance
Warning
To get the best performance
possible, the mounting location of
the front Radar and Laser Receiver
is critical. Although radar signals
will pass through some types of
plastic, it is critical that this
receiver be mounted level, and
have an unobstructed “view” of
the road.
Beltronics
5442 West Chester Road
West Chester OH 45069
©2007 BELTRONICS, STi-R, TotalShield Technology and AutoScan are trademarks of BELTRONICS USA Inc.
Safety Warning System is a registered trademark of Safety Warning System L.L.C.
Customer Service 800-341-2288
www.beltronics.com
STi-R Installation Manual
A B
Radar/Laser Receiver
1 Determine the best location for the
Receiver. The best location is typically
under the bumper, or inside the front grill of
the vehicle. For the best performance, install
the Receiver horizontally, with a clear “view”
of the road.
2 Using the supplied mounting hardware,
mark the hole locations and drill pilot holes
in the vehicle if necessary. It’s best to check
and double-check clearances BEFORE
drilling the holes.
3 Mount the Receiver using the supplied
hardware. (If right-angle mounting bracket
is used, secure Receiver to the right-angle
bracket first, then install bracket with
Receiver to the vehicle.)
Note:
1. Do not drill holes in the Receiver itself.
2. Thoroughly investigate location before
drilling any holes.
3. Keep all cables away from moving parts,
and hot surfaces (radiator, hoses, etc.).
4. DO NOT splice cable.
Radar/Laser Receiver Cable
1 Connect the receiver cable to the Receiver.
2 Route cable to firewall, and secure with
zip-ties (included).
3 Route receiver cable into the vehicle’s
interior. If there is not a suitable opening,
drill a 13/32" or 7/16" hole.
4 Pull cable through firewall, and plug
connector into the jack labeled “Front
Receiver” on the Interface.
B
A
5 Pull grommet (located on the receiver
cable itself) through the firewall to seal the
hole. Use silicone sealant (not supplied) if
necessary.
Note:
1. Connection between the Receiver and the
receiver cable, must be located in a dry
location under the hood.
2. Only drill hole in firewall after thoroughly
investigating location first, ensuring no
other wires, hoses, etc. will be damaged.
3. Keep all cables away from moving parts,
and hot surfaces (radiator, hoses, etc.).
4. DO NOT splice cable.
12 Vol t
Pow er Lin e
±
D
Optional Concealed Display
1 Drill a 1/4" hole, and install the LED clip.
2 Snap LED into clip from behind.
3 Plug the modular connector into STi-R’s
Interface marked “Concealed LED Display.”
D
E
Interior of Vehicle
E
Display
1 Determine the best location for the Display
in the vehicle’s interior. (Consult customer if
necessary.)
2 Install Display using double-sided tape on
the back. Simply remove paper backing and
press onto clean surface. You may also
custom-install the display into the dashboard
using the supplied template. Seek
professional assistance for this.
3 Route cable and plug into jack marked
“Display” on Interface.
Note:
Make certain that the Display is clearly
visible from the driver’s position.
F
Controller
1 Determine the best location for the Display
Controller in the vehicle’s interior. (Consult
customer if necessary.)
2 Install Controller using supplied doublesided tape located on the back. Simply peal
off the paper backing and press onto clean
surface.
3 Route cable and plug into jack marked
“Controller” on the Interface.
Note:
Make certain that the Controller can be
easily accessed without interfering with
normal driving.
A
C
Interface
1 Install Interface under the dash using
supplied zip-ties. DO NOT MOUNT IN
ENGINE COMPARTMENT.
2 Connect black wire (–) to ground, and redstriped wire (+) to a switched 12-volt supply.
(If STi-R is left in the “on” position, it will
automatically power on and off with the
ignition). Use blue 3M connector (provided)
to tap into existing circuit if needed.
3 The front Receiver, Display and Controller
all plug into the Interface. (Be sure to plug
all cables into the correct labeled jacks.)
C
G
Amplified Speaker
1 Determine the best location for the
Speaker in the vehicle’s interior. (Consult
customer if necessary.)
Note:
The speaker is loud enough to be mounted
under the dash so it is not seen.
2 Mount the Speaker bracket using the
supplies hardware.
F
G
3 Plug the audio line (ear phone jack
connector) into the Interface jack marked
“Speaker”.
4 Connect the (+) to a switched power
connection on the fuse panel, and connect
the (–) to ground.
TEST
After all components are installed correctly:
1 Turn vehicle’s ignition to the “on” position.
2 Turn the STi-R on by pressing the “PWR”
button on the Controller.
3 The STi-R will cycle through a startup
sequence.
4 If any error messages come up, see page 23
of the Owner’s Manual for details.
Loading...