Beltronics Sti Magnum User Manual
M A G N E S I U M
C O N S T R U C T I O N
BELTRONICS
5442 West Chester Road
West Chester OH
45069 USA
USA 800-341-2288
www.beltronics.com
©2011 BELTRONICS
Made in Canada
Features, specifications and prices subject to change without notice.
Model: STi MAGNUM
D I G I T A L R A D A R•L A S E R•S A F E T Y D E T E C T O R
’s Manual
Owner
Congratulations
Quick Reference Card
The BELTRONICS STi MAGNUM is the most
advanced radar, laser and safety detector
ever designed, and is ready to use right out
of the box with our recommended factory
settings.
The STi MAGNUM includes full X, K,
SuperWide Ka, and Safety Warning System
radar capability, front and rear laser
detection, dual LNA (low noise amplifier)
microwave receivers, digital signal
processing (DSP) for superior range and
reduced false alarms, our patented Mute
and AutoMute, audible and visual band
alerts, and all the performance you’d expect
from BELTRONICS.
In addition, the BELTRONICS STi
MAGNUM contains the following
revolutionary features:
• Dual LNA (low noise amplifier)
receivers provide the longest
possible warning against all radar
threats.
• Advanced Signal Rejection Software
(TSR).
• TotalShield
provides the ultimate in
™ RF Technology
undetectability.
• Programmable Alert Lamp provides
additional visual indication of alerts.
• Rugged magnesium case provides
the ultimate protection for your
investment.
• Ultra-bright text-display provides
easy to read information from any
angle.
• High and low voltage warning is
given any time the vehicle’s voltage
drops below 10.5 volts, or goes
above 16.5 volts.
• Easy-to-use Programming lets you
customize up to 9 features.
• Exclusive AutoScan mode intelligently
reduces unwanted false alarms.
• Tech Display provides actual
numeric radar frequency for any
radar signal.
• Programmable Bands (on/off).
• Detects and decodes up to 64 Safety
Warning System messages.
• Includes new coiled SmartPlug,
which provides a convenient mute
button right on the plug.
If you’ve used a radar detector before,
a review of the Quick Reference Guide on
pages 4 and 5, and the Programming
information on pages 12 and 13 will briefly
explain the new features.
If this is your first detector, please
read the manual in detail to get the most
out of your BELTRONICS STi MAGNUM’s
outstanding performance and innovative
features.
Please drive safely.
FCC Note: Modifications not expressly
approved by the manufacturer could
void the user’s FCC granted authority
to operate the equipment.
Remove card along perforations
1
BELTRONICS STi MAGNUM Quick Reference Card
There are 9 user-selectable options so you
can customize your STi MAGNUM for your
own preferences.
The buttons labeled VOLUME/MUTE
and SENS are also used to enter the Programming Mode, REVIEW your current program
settings, and to CHANGE any settings as
desired. The abbreviations PGM, RVW, and
CHG are located on the lower part of the
display lens and are highlighted in graphics.
How to use Programming
1 To enter Program Mode, press and
hold both VOLUME/MUTE and SENS
buttons down for 2 seconds
will beep twice, and will display the word
Program.
2 Then press the RVW button to review
the current settings. You can either tap
the button to change from item to item, or
hold the button to scroll through the items.
3 Press the CHG button to change any
setting. You can either tap the button to
change from setting to setting, or hold the
button to scroll through all the options.
4 To leave Program Mode, simply wait
8 seconds without pressing any button.
The unit will display
times, and return to normal operation.
Factory Default Settings
To reset the STi MAGNUM to its original
factory settings, press and hold the
“VOLUME/MUTE,” and “SENS,” buttons
while turning the power on. The STi
MAGNUM’s display will provide a
message, accompanied by an audible
alert, acknowledging the reset.
Remove card along perforations
An example
Here is how you would turn the STi
MAGNUM’s AutoMute feature off.
1 Enter the Program Mode by holding
both the VOLUME/MUTE and SENS buttons
down for 2 seconds. The STi MAGNUM will
beep twice and display Program.
2 Then hold the RVW button down. The
STi MAGNUM will scroll through the
categories, starting with display
power-on indication
lamp
(Alamp), Voice, Power-on sequence,
. The unit
Complete, beep 4
signal strength meter, and then AutoMute.
3 Release the RVW button when the STi
MAGNUM shows the AutoMute item. Since
the factory setting is for AutoMute to be on,
the STi MAGNUM will display aMute ON.
If you accidentally don’t release the
Review button in time, and the STi
MAGNUM goes to the next category, hold
the RVW button down again, and scroll
through the categories again until
is displayed.
4 Press the CHG button to change from
aMute ON to aMute OFF.
5 To complete the Programming, simply
wait 8 seconds without pressing any
The STi MAGNUM will display
button.
Complete, beep 4 times, and return to
normal operation.
Reset
(Display),
(Pilot), then alert
aMute
Programming Details
Table of ContentsQuick Reference Card
Remove card along perforations
BELTRONICS STi MAGNUM Quick Reference Card
Press the RVW button
to go from one category
* Factory Default Settings
to the next
(Power-on indication)
ALERT LAMP
POWER-ON SEQUENCE
SIGNAL STRENGTH METER
AUTOMUTE
BRIGHTNESS
Disp STD
DISPLAY
Disp INV
Pilot HWY
PILOT
Pilot H
Pilot V
Alamp ON
Alamp OFF
Voice ON
VOICE
Voice OFF
PwrOn STD
PwrOn FST
Meter STD
Meter THT
Meter TEC
aMute ON
aMute OFF
Brt Auto
Brt Min
Brt Med
Brt Max
Brt Dark
Bands DFT
BANDS
Bands MOD
X ON or OFF (default is on)
K ON or OFF (default is on)
Ka ON or OFF (default is on)
POP ON or OFF (default is off)
LSR ON or OFF (default is on)
SWS ON or OFF (default is off)
TSR ON or OFF (default is on)
Press the CHG button
to change your setting
within a category
* Standard display
Inverted display
* Full word: Highway, AutoScan, etc.
Letter: H, A, C, or Cnx
Vehicle voltage
* Alert lamp on
Alert lamp off
* Voice alerts on
Voice alerts off
* Standard power-on sequence
Fast power-on sequence
* Standard signal strength meter
Threat Display
Tech Display
* AutoMute on
AutoMute off
* Automatic brightness
Minimum brightness
Medium brightness
Maximum brightness
All dark
* Default bands
Factory default settings modified
Turn bands “ON” or “OFF” by
pressing the “SENS” button
Remove card along perforations
Quick Reference Guide 4-5
Installation 6-7
• Power Connection 6
• Mounting Location 6
• Windshield Mount 7
Controls and Features 8-11
• Power and Volume Control 8
• Power-on Indication 8
• Voice 8
• AutoMute 8
• Mute 8
• Sensitivity Button 9
• Brightness 9
• Audible Alerts
• Power Connector
• Signal Strength Meter
• Threat Display
• Tech Display
10
10
10
11
11
Programming 12-16
• How to use Programming 12
• Example of Programming
• Overview of Programming
• Details of Programming
Technical Details 17-23
• Specifications 17
• Interpreting Alerts
• How Radar Works 20
• How “POP” Works 20
• TSR Traffic Signal Rejection Software 21
• How Laser Works
™
• How TotalShield
Technology Works 22
• How Safety Radar Works 22-
Service 24-29
• Troubleshooting 24-25
• Service 26
• Registration 27-28
• Warranty and Accessories 29
32
12
13
14-16
18-19
21
23
Quick Reference Guide
To begin using your STi MAGNUM,
just follow these simple steps
1 Plug the small end of the power cord
into the side jack of the detector, and
plug the large end of the power cord
into your vehicle’s lighter socket.
2 Mount your STi MAGNUM on the
windshield using the supplied
windshield mount.
3 Press the PWR button, located on the
left side of the front panel, to turn the
STi MAGNUM on.
4 Press and hold the VOLUME/MUTE
button to adjust the volume level.
Please read the manual to fully understand
STi MAGNUM’s operation and features.
QuickMount Slot
Insert STi MAGNUM’s adjustable
Windshield Mount into this slot. Page 7
QuickMount Button
Press the button, and slide the Windshield
mount into one of its four locking positions.
Page 7
Power Button (PWR)
Press the PWR button to turn the STi
MAGNUM on or off.
AutoMute
STi MAGNUM’s patented AutoMute
automatically reduces the volume level of
the audio alert after a brief period. If you
prefer, you can turn AutoMute off. Page 8
Programming
The STi MAGNUM is ready to go, just plug
it in and turn it on. But you can also easily
change 9 features for your preferences.
12-16
Pages
Radar Antenna and Laser Lens
The rear panel of your STi MAGNUM should
have a clear view of the road ahead. For
best performance, do not mount the
STi MAGNUM directly behind
windshield wipers or tinted
areas. Page 6
Alphanumeric Display
The STi MAGNUM’s display will show
Highway, AutoScan, City, or City NoX as its
power-on indication. If you prefer, you can
choose other power-on indications. Pages
12-15
During an alert, the display will indicate
the radar or laser band, and a precise bar
graph of signal strength. Page 10
NOTE: In the Dark Mode the display
will not light during an alert. Page 9
Rear Laser Port
Receives laser signals from behind the
vehicle.
Power Jack
Plug the power cord into this connector.
Page 6
Earphone Jack
Accepts standard 3.5mm mono earphone.
VOLUME•MUTE Button
Press and hold the VOLUME/MUTE button
(below the display) to adjust the alert
volume level.
Briefly press this button to silence the
audio for a specific alert. (The audio will
alert you to the next encounter.) Page 8
Sensitivity Button (SENS)
Switches between Highway, AutoScan, City
and City NoX settings. In general, we
recommend the AutoScan mode. Page 9
4
5
Installation
Power Connection
To apply power to the STi MAGNUM, plug
the small end of the power cord,
(telephone type connector) into the
modular jack on the STi MAGNUM’s right
side, and plug the lighter plug adapter into
your vehicle’s lighter socket or accessory
socket.
Your STi MAGNUM operates on 12 volts DC
negative ground only. The lighter plug
provided is a standard size and will work in
most vehicles. However, some vehicles may
require the optional European sleeve to
ensure a snug fit. If so, simply call our
service department and we’ll send you one.
This sleeve slides over the power cord’s
lighter plug adapter. Of course, your lighter
socket must be clean and properly
connected for proper operation.
N0TE: Depending on your vehicle, the
lighter socket power may either be
continuously on, or it may be switched
on and off with your ignition switch. We
suggest using a direct-wire SmartPlug
connected to a switched circuit at the
fuse box if the lighter socket is
continuously on.
Mounting Location
WARNING: BELTRONICS cannot
anticipate the many ways STi MAGNUM
can be mounted. It is important that you
mount STi MAGNUM where it will not
impair your view nor present a hazard
in case of an accident.
Where to mount STi MAGNUM
For optimum detection performance, we
recommend the following:
• Using the Windshield QuickMount,
mount your STi MAGNUM level, and
high enough on your front windshield to
provide a clear view of the road from the
front and rear.
• Mount the STi MAGNUM away from
windshield wipers, other solid objects, and
heavily tinted areas that might obstruct the
radar antenna or laser lens.
Windshield QuickMount
The STi MAGNUM’s QuickMount windshield bracket is designed for unobtrusive
and hassle-free mounting and removal.
1 Depress the adjustment button on
the top of the STi MAGNUM (by the word
BELTRONICS) and slide the QuickMount
bracket into the slot until it is locked into
the position which best fits the angle of
your windshield (there are four settings
available). For extremely horizontal
or extremely sloped windshields, the
QuickMount bracket can be bent.
To ensure that the suction cups
adhere to the windshield firmly,
be sure to keep both your windshield and
the suction cups clean.
2 To adjust the STi MAGNUM on your
windshield, use the QuickMount
adjustment button located on the top
of the STi MAGNUM, and slide the STi
MAGNUM forward or backward to obtain a
level position.
NOTE: When installed and adjusted
properly, the back top edge of the STi
MAGNUM should rest solidly against
your windshield.
CAUTION: A few vehicles (including some
Porsches) have windshields with a soft
anti-lacerative coating on the inside
surface. Use of suction cups will
permanently mar this coating. Consult
your dealership or the vehicle owner’s
manual to determine if your windshield
has this coating.
User’s Tip
You can leave the QuickMount bracket
in place on your windshield, and easily
remove STi MAGNUM by pressing the
adjustment button and sliding the STi
MAGNUM off the mount. Again, be sure to
position the bracket where it won’t present
a hazard in the event of an accident.
Additional mounts are available for other
vehicles in your household.
6
7
Loading...