Beltronics RX 75 User Manual
Professional
S
eries
Professional
S
eries
Please read both sides of these instructions before starting your installation.
For the easiest trouble-free installation, install the Interface first, and wire it to a
12-volt switched circuit.
Then before installing the other components, plug all of them into the Interface
and power up the unit to confirm proper operation.
Read This First
A professional installer must install your
new . Installation of
this system requires experience and
expertise in automotive electronics. Car
Audio specialists and many car dealers
can install for you.
Attempting to install this product
without expertise in automotive
electronics installation can cause
personal injury, or damage to your
vehicle.
If your vehicle is damaged during
installation, its safety systems may be
compromised, which could cause
personal injury or property damage.
Improper installation may void
the warranty.
BEL
BEL
To get the best performance possible, the
mounting location of the Radar Receiver is
critical. Although radar signals will pass
through some types of plastic, mounting
the Radar Receiver so that it has a clear
“view” of the road will ensure maximum
warning.
Since Laser signals will not pass through
any objects, including plastic, it is critical
that the Laser Receivers be mounted
perfectly level, and have an unobstructed
“view” of the road.
1
2
3
4
Important Installation Warnings Performance Warning
IMPORTANT NOTES
Front Radar Receiver
• Miniature weather-proof Radar Receiver
• Universal mounting bracket with stainless steel hardware
• Built-in 6 foot shielded cable with waterproof connector
• 13 foot shielded cable with in-line grommet and waterproof
connector
• 12 nylon wire ties to secure cable
Front Laser Receiver
• Weather-proof sensor
• 13 foot shielded cable with in-line grommet
• Universal mounting bracket with stainless steel hardware
Miniature Display Controller
• User Display mounts easily to instrument pod, dashboard,
or console
• Velcro and adhesive pads provided for secure mounting
• Optional hidden display included
Interface
• Central module connects to switched 12-volt power and ground
• All components plug directly in using modular connections
• 3M connector taps into existing vehicle wiring
Rear Laser Receiver
• Weatherproof license plate mounted sensor
• 30-foot cable with modular connector
Documentation
• Comprehensive Owner’s Manual
• Installation Manual
Built-in Diagnostics
• Confirms all components are operational
5442 West Chester Road, West Chester, Ohio 45069
Sales/Service 800-341-2288 • www.beltronicspro.com
©2003 SWS™is a trademark of SWS LC. Features, specifications and prices subject to change without notice.
TM
MODEL RX75
MODEL RX75
CUSTOM INSTALLED
RADAR/LASER SAFETY SYSTEM
CUSTOM INSTALLED
RADAR/LASER SAFETY SYSTEM
BEL
BEL
Professional
S
eries
Professional
S
eries
12770_Bel Pro Remote_Manual 6/2/03 10:40 PM Page 1 Scale: 100%
Note:
1. Connection between the radar receiver, and the receiver cable,
must be located in a dry location under hood.
2. Only drill hole in firewall after thoroughly investigating location
first, ensuring no other wires, hoses, etc. will be damaged.
3. Keep all cables away from moving parts, and hot surfaces
(radiator, hoses, etc.).
4. Do not splice cable.
Laser Receiver Cable
1 Route Laser Receiver cable to firewall, and secure with zip-ties
(included).
2 Route Laser cable into the vehicle’s interior. If there is not a
suitable opening, drill a 13/32" or 7/16" hole.
3 Pull cable through firewall, and plug connector into jack marked
“Front Laser/Shifter” on Interface.
4 Pull grommet (located on cable) through the firewall to seal the
hole. Use silicone sealant (not supplied) if necessary.
Note:
1. Only drill hole in firewall after thoroughly investigating location
first, ensuring no other wires, hoses, etc. will be damaged.
2. Keep all cables away from moving parts, and hot surfaces
(radiator, hoses, etc.).
3. Do not splice cable.
Front Radar Receiver
1 Determine the best location for the Radar
Receiver. The best location is typically under
the bumper, or inside the front grill of the
vehicle. For the best radar performance,
install the Radar Receiver horizontally, with a
clear “view” of the road.
2 Using the built-in mounting holes on the
Receiver, or the supplied right-angle mounting
bracket, mark location. Drill pilot holes in the
vehicle if necessary.
3 Mount Radar Receiver using the supplied
hardware. (If right-angle mounting bracket is
used, secure Radar Receiver to the rightangle bracket first, then install bracket with
Radar Receiver to the vehicle.)
Note:
1. Do not drill holes in the receiver itself.
2. Thoroughly investigate location before
drilling any holes.
3. Keep all cables away from moving parts,
and hot surfaces (radiator, hoses, etc.).
4. Do not splice cable.
Front Laser Receiver
1 Determine best location for the Laser Receiver.
For optimum performance, install the Laser Receiver
near the front license plate if possible, with a clear “view” of the road.
2 Using the supplied mounting bracket, mark location. Drill pilot
holes in the vehicle if necessary.
3 Mount the Laser Receiver using the supplied hardware, making
sure that it is level to the road.
Note:
1. Do not drill holes in the Laser Receiver itself.
2. Thoroughly investigate location before drilling any holes.
3. Keep all cables away from moving parts, and hot surfaces
(radiator, hoses, etc.)
4. Do not splice cable.
5. Make certain that the Laser Receiver is level, and has a
clear “view” of the road.
Radar Receiver Cable
1 Connect the receiver cable to the receiver.
2 Route cable to firewall, and secure with zip-ties (included).
3 Route receiver cable into the vehicle’s interior. If there is not a
suitable opening, drill a 13/32" or 7/16" hole.
4 Pull cable through firewall, and plug connector into the jack labeled
“Front Radar” on the Interface.
5 Pull grommet (located on the receiver cable itself) through the
firewall to seal the hole. Use silicone sealant (not supplied) if necessary.
Installation Manual
D
F
User Display
1 Determine the best location for the User Display in the
vehicle’s interior. (Consult customer if necessary.)
2 Install User Display using supplied velcro, or double-sided tape.
3 Route cable and plug into jack marked “Display” on Interface.
Note:
1.
Make certain that the User Display is clearly visible from the
driver’s position, and that the controls can be easily accessed
without interfering with normal driving.
Interface
1 Install Interface under the dash using supplied zip-ties.
DO NOT MOUNT IN ENGINE COMPARTMENT.
2 Connect black wire (–) to ground, and red-striped wire (+) to a
switched 12-volt supply. (If
BEL Pro Remote is left in the “on”
position, it will automatically power on and off with the ignition).
Use blue 3M connector (provided) to tap into existing circuit if
needed.
3 Radar Receiver, front Laser Receiver, rear Laser Receiver, and
Display Controller all plug into the Interface. (Be sure to plug all
cables into the correct labeled jacks.)
A
B
C
MODEL RX75
E
BEL
BEL
Rear Laser Receiver
1 Remove two license plate screws,
(top or bottom).
2 Mount Laser Receiver to plate using
supplied mounting bracket.
3 Route wire through trunk compartment,
and into the vehicle’s interior.
4 Insert connector to jack labeled “Rear
Laser Receiver” on Interface.
TIPS
1. Do not block license plate illumination.
2. Do not cover any required license plate
information.
INSTALLATION ALTERNATIVES:
1. Cable can be routed under vehicle
(keep away from hot and moving parts)
then brought into the vehicle’s interior.
2. Cable can be cut if necessary for
routing. Reconnect and solder each of
the three wires, and seal with heatshrink tubing.
Remote Mute/Volume Adjust
1 Determine best location for the
Remote Mute Button.
2 Clean surface area.
3 Remove paper backing on the back of
the button, and press onto surface.
4 Route cable and plug into jack marked
“Mute” on Interface.
Test
After all components are installed correctly:
1 Tu rn vehicle’s ignition to the “on” position.
2 Tu r n BEL Pro Remote on by pressing the Power button.
3 BEL Pro Remote will cycle through a startup sequence.
4 If any error messages come up, see page 00 of the Owner’s
Manual for details.
7
Interior of
Vehicle
12 Volt
Power
Line
Concealed
Display
(optional)
Remote Mute
Button
External
Speaker
(optional)
FRONT
REAR
F
E
C
D
B
A
G
G
Optional Pro Pack
MODEL RX75PP
Optional Pro Pack
Further customize the install process with these
additional accessories:
Amplified speaker enables voice alerts for radar
and SWS messages. The increased audio level is
ideal for convertibles, trucks, SUV's etc.
Discreet in-dash LED allows the control panel to be
hidden, while providing power-on (green) and alert (red)
status.
In-dash trim bezel provides a custominstalled finish to any installation.
Installation Instructions enclosed with Pro Pack
12770_Bel Pro Remote_Manual 6/2/03 10:40 PM Page 2 Scale: 100%
Loading...