VOLTAGE & W/B ADJUSTMENT……………………………… 44
SAFETY PRECAUTIONS …………………………………………49
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 2/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
(MODULE USE AND CONSIDERATIONS IN SERVICING)
TROUBLESHOOTING.…….…………………………..…………. 53
IMAGE STICKING CHARACTERISTICS ……………………… 64
ISM MODE………………………………………………………….. 66
- Audio Input (Bottom,RCA Ja ck,AV,Component1/2,S-Video,RGB)
- RS-232C (9 pin) , TCP / IP Support (0~255set)
8. Function :
- ARC
- PIP (PIP Swap,Sound Swap)
- PBP (4:3,16:9)
- MTS
- TTX
9. External Interface
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 4/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
1) AV / COMPONENT Output
ITEM MIN TYP MAX UNIT
AV Video Input Level 0.85 1.00 1.15 Vpp
AV Sync Input Level 0.24 0.29 0.32 Vpp
AV Burst Input Level 0.14 0.28 0.35 Vpp
AV Video Input Level 0.47 0.63 0.79 V
AV Audio Input L/R 0.47 0.63 0.79 V
Component Video Input Level
(Y,Cb/Pb,Cr/Pr)
Analog RGB, H/V Input Level 0.6 0.7 0.8 Vpp
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 6/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 7/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
OPTIONAL EXTRAS
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 8/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
◐Optional extras can be changed or modified for quality improvement without notification new optional
extras can be added.
◐Contract your dealer for buying these items.
REMOTE CONTROL BUTTONS
※ When using the remote control aim it at the remote control sensor of the Monitor.
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 9/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
TELETEXT FUNCTION
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 10/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
DISPLAY CELL DEFECT SPECIFICATION
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 11/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
[ PDP42V51000,51300,51330]
DEFINITION OF CELL DEFECT ZONE
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 12/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
1) Definition of Cell defect Zone
2) Display Dot Diagram
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 13/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
ANALOG RGB
COMPONENT1
(DTV)
COMPONENT2
(DVD)
TUNER
CVBS
COMPOSITE
IN
HALF SCART
VIDEO IN/OUT
FULL SCART
VIDEO IN/OUT
S-VIDEO
S-VIDEO
AUDIO IN
PC
AUDIO IN
SCART_FULL
AUDIO IN
SCART_HALF
AUDIO IN
COMPOSITE
AUDIO IN
FULL SCART
RGB
DTV
AUDIO IN
DVD
AUDIO IN
TUNER
SIF
SCART_FULL
AUDIO OUT
SCART_HALF
AUDIO OUT
24LC21
EEPROM
R,G,B,H,V
Y,Pb,Pr
Y,Pb,Pr
CVBS,ID
CVBS,ID
CH,LU
SVIDEO_IN R/L
PC_IN R/L
F_SC_IN R/L
H_SC_IN R/L
AV_IN R/L
SCART RGB(R,G,B,FB)
DTV_IN R/L
DVD_IN R/L
2
2
2
2
2
2
2
2
2
2
2
F_CVBS_OUT_R/L
2
H_CVBS_OUT_R/L
5
3
CXA2089Q
MUX(U3)
A/V
(U8)
BA7657
SWITCH
4
V OUT2
Y,C OUT2
V OUT1
Y,C OUT1
MSP0 L/R
MSP1 L/R
BSV-4251 &BSV-4251A (42") PDP TV BLOCK DIAGRAM
AD9883
CONVERTER
4
BA7657
(U28)
SWITCH
(U2)
A/D
TTX RGB
(R,G,B,FB)
4
2
2
20.25MHz
VPC3230D-C5
VIDEO
DECODER
H_SCART_OUT
20.25MHz
VPC3230D-C5
VIDEO
DECODER
(MAIN)
6.000MHz
SDA5550
(U26)
TTX
18.432MHz
(U45)
MSP3453
AUDIO
PROCESSOR
(U39)
(SUB)
(U41)
24
TTX_CVBS
MSP_OUT1
L/R
CH1 RGB
CH1 GB
CH2 GB
SST39VF080AT
FLASH
HY62U8200
RAM
24LC16
EEPROM
SPK
16
R
TDA7495S
AUDIO AMP
SPK
L
5
3
2
4
2
24
16
20.000MHz
(U21)
PW565
DS232AS
RS232
TRANSMITTER
RS232
DSUB-9P
VCC12
12
V
I/O EXTENDER
VCC5
AP1501-50
12V12V12V12V
80.000MHz
KYE
PAD
RC1117
VCC3
DE [23:0]
DO [23:0]
FSDQM[7:0]
FSDATA[63:0]
H SYNC
V SYNC
DEN
DCLK
ADR[12:0]
A[21:0]
D[7:0]
REMOCON
VCC5A
AP1501-50
24
TRANSMITTER
POWER
MODULE
SIL164
TMDS
K4S643232E X 2
SDRAM
TM28F800B3
FLASH
MOMORY
24LC256
EEPROM
VCC5D
AP1501-50
TX0 +
TX0 -
TX0+
TX1 +
TX1 -
TX2 +
TX2 -
TXC +
TXC -
VCC9
KIA7809
MODULE
42"
5VST
5V
FAN
12V
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 14/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 15/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
MODULE FUNCTION & DEFINITION
1. The function of each part
Part name Main function
Y-Board (Scan Driver) Execution of the scan and sustain operation connecting scan electrode (Y-electrode) and FPC of panel
Z-Board (Common Sustain Driver) Execution of the sustain operation connecting sustain electrode (Z-electrode) and FPC of panel
X-Board (Address Driver) Execution of the address operation connecting the botton plate address electrode (X-electrode) and FPC of panel
Control Board Distribution to X, Y, Z board after creation of display data and driver timing for an image and sound signal to be input from outside
DC/DC-2 Board Distribution to X, Y, Z board after conversion from input voltage of Vs, Va, Voc to circuit logic voltage (5V)
FPC (Flexible Plate Circuit) The pattern connection of PCB and panel
COF (Chip On Film) It means to integrate a kind of IC Chip with FPC
2. A term and definition of defect
2.1 CELL DEFECT
Term The actual state A cause
Non lighting Cell Defect Cell is always “Off” ¢º a different thing or structural defect of Cell
Flashing Cell Defect Cell repeat On / Off ¢º a different thing or structural defect of Cell
Non-extinguishing Cell Defect Cell is always “On” ¢º a different thing or structural defect of Cell
High Intensity Cell Defect A cell is the brighter than others on same color ¢º a different thing or structural defect of Cell
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 16/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
MODULE BASIC CONFIGURATION
[PDP42V51000,51300,51330]
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
3 ( 5V STBY ) I 5V 5V INPUT PORT FOR VSC STANDBY
2 ( RL-ON ) O 5V / 0V
6 ( 5V-MNT ) I 5V / 0V
4 ( GND )
5 (VAVS-ON ) O 5V / 0V
7 ( NC ) No Connection
1 ( REMOCON ) I 5V Monitor transmitter signal input port
2 ( GND )
3 ( 5VST ) O 5V Stand by 5V Output Port
4 ( GND )
5 (LED-R ) O 5V / 0V
6 (LED-G ) O 5V / 0V
AC POWER OFF LOW
:Turn off the power by power sequence to
stabilize PDP MODULE in case of power
breakdown.
RELAY CONTROL PORT FOR POWER ON
: Relay On High , Relay off Low
PDP MODULE STABLE CHECK PORT.
: The port to provide control signal to PDP
MODULE after the controller stabilized. At the
moment, MICOM always check this signal and
turn off the power when the signal is low.
PORT FOR VA/VS OF PDP MODULE.
: ON HIGH , OFF LOW
:To protect PDP MODULE, Micom turn on the
Va/Vs 2 seconds after checking 5V-MNT.
RED LED CONTORL OUTPUT PORT
: High : Red LED On
GREEN LED CONTORL OUTPUT PORT
: High : Green LED On
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 18/75
J9
J10
J11
J1
SERVICE MANUAL (BSV-4251 BSV-4251A )
7 ( POWER ) I 5V / 0V LOCAL KEY INPUT PORT FOR POWER
8 ( VOL+ ) I 5V / 0V LOCAL KEY INPUT PORT FOR VOL +
9 ( VOL- ) I 5V / 0V LOCAL KEY INPUT PORT FOR VOL 10 ( SRC/SEL ) I 5V / 0V LOCAL KEY INPUT PORT FOR SOURCE
11 (MENU) I 5V / 0V LOCAL KEY INPUT PORT FOR MENU
12 (CH-) I 5V / 0V LOCAL KEY INPUT PORT FOR CH13 (CH+) I 5V / 0V LOCAL KEY INPUT PORT FOR CH+
1 ( 32V ) I 32V Audio AMP POWER INPUT PORT
2 ( 32V ) I 32V Audio AMP POWER INPUT PORT
3 ( GND ) 0V Audio AMP POWER GROUND PORT
4 ( GND ) 0V Audio AMP POWER GROUND PORT
1 ( L OUT ) O
2 ( L GND ) Audio AMP LEFT GROUND PORT
3 ( R OUT ) O
4 ( R GND ) Audio AMP RIGHT GROUND PORT
1 ( S-SCL ) RS-232C CLOCK LINE
2 ( S-SDA ) RS-232C DATA LINE
3 ( FS )
4 ( GND ) 0V
1 ( VCC5 ) I 5V 5V Input
2 ( VCC5 ) I 5V 5V Input
3 (SCART_R) I
4 (SCART_G) I
5 (SCART_B) I
6 (SCART_FB) I +1V to +3V / 0V to 0.4VSCART FAST BLANKING
7 ( GND ) 0V
8 (FSCART_CVBS_IN)
9 ( GND ))0V
10 (HSCART_CVBS_IN)
11 ( GND ) 0V
12 ( FSCART_ID )
13 ( HSCART_ID )
14 ( GND ) 0V
15 (F_CVBS_OUT)
16 ( GND ) 0V
17 (H_CVBS_OUT)
18 ( GND ) 0V
19 (F_CVBS_L_OUT)
20 (F_CVBS_R_OUT)
21 ( GND ) 0V
22 (H_CVBS_L_OUT)
23 (H_CVBS_R_OUT)
I
I
I 4:3 / 16:9 VIDEO STATUS
I 4:3 / 16:9 VIDEO STATUS
O
O
O
O
O
O
0.7Vpp±0.1pp
0.7Vpp±0.1pp
0.7Vpp±0.1pp
1.0Vpp±3dB
1.0Vpp±3dB
1.0Vpp±3dB
1.0Vpp±3dB
0.5Vrms±3dB
0.5Vrms±3dB
0.5Vrms±3dB
0.5Vrms±3dB
Audio AMP LEFT OUTPUT PORT( 8 §Ù )
Audio AMP RIGHT OUTPUT PORT ( 8 §Ù )
SCART RED INPUT PORT
SCART GREEN INPUT PORT
SCART BLUE INPUT PORT
SCART1 CVBS INPUT PORT
SCART2 CVBS INPUT PORT
SCART1 CVBS OUTPUT PORT
SCART2 CVBS OUTPUT PORT
SCART1 AUDIO LEFT OUTPUT PORT
SCART1 AUDIO RIGHT OUTPUT PORT
SCART2 AUDIO LEFT OUTPUT PORT
SCART2 AUDIO RIGHT OUTPUT PORT
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
: Adjustment of contrast and brightness for scaler generating power.
„ 4. PW565
: Adjustment of contrast and brightness for scaler input port (CH1 or CH2).
„ 5. VPC3230-MAIN
: Value adjustment for video decoder¡¯s brightness and contrast, color tickness in
the main window.
„ 6. VPC3230-SUB
: Value adjustment for video decoder¡¯s brightness and contrast, color tickness in
the sub window.
„ 7. ADC
: Value adjustment for brightness and contrat, color thickness of analogue RGB,
Y,Pb,Pr of AD9883 A/D convertor.
„ 8. Heatrun
: The mode when you do aging.
„ 9. Version
: It shows the information of Firmware version and Panel.
„ 10. Setup
: Installation of TTX language and video, protocol, logo.
CALIBRATION MENU
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 21/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
CALIBRATION MENU
„ 1. PC Calibration
: Automatic adjustment as the fittest status of white balance for analogue input (PC)
„ 2. DTV Calibration
: Automatic adjustment as the fittest status of white balance for component2 (DTV)
input.
OPTION TABLE MENU
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 22/75
OPTION TABLE MENU
„ Flesh tone
„ LNA(Low Noise Amplifier)
: On/Off Installation of screen quality improv ement fuction, when TV input signal is
weak.
„ Blue Screen
: When there are no input signal of the TV and external equipment, you can install the
screen color as blue.
„ Melody Volume
: Installation of the melody volume for initial soft power On/Off. The volume is exfactoried as ¡°0 ¡± due to license.
„ Video Mute
„ TTX TOP
„ Auto FM
„ Help
„ Area
„ High Deviation
SERVICE MANUAL (BSV-4251 BSV-4251A )SERVICE MANUAL (BSV-4251 BSV-4251A )
COLOR CONTROL MENU
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 23/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
COLOR CONTROL MENU
„ Sub-Brightness
: The brightness adjustment of scaler generating power.
„ Red, Green, Blue Offset
: The brightness adjustment of each Red, Green, Blue for scaler generating power.
„ Brightness
: The brightness adjustment of current screen. Adjustment value of brightness for User
Menu
„ TTX-Bright
: It is not useful mode.
„ Sub Contrast
: Contrast adjustment of scaler generating power.
„ Red, Green, Blue Gain
: Contrast adjustment of each Red, Green, Blue for Scaler generating power.
„ Contrast
: Contrast adjustment for current screen. The value adjustment of contrast for User Menu
„ TTX-Contrast
: It is not useful mode.
PW565 MENU
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 24/75
PW565 MENU
„ Red,Green,Blue Gain
: The contrast value adjustment of each Red, Green, Blue for scaler input port (CH1 OR
CH2)
„ Red,Green,Blue Offset
SERVICE MANUAL (BSV-4251 BSV-4251A )
: The brightness adjustment of each Red, Green, Blue for scaler input port (CH1 OR CH2)
„ APL
„ Pixel Shift
„ Pixel Number
„ Time
„ Virtual Framelock
: Installation of flame frequency for panel (50Hz, 60Hz).
„ Alpha
„ Beta
„ Degree
VPC3230-MAIN MENU
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 25/75
VPC3230-MAIN MENU
„ CT
: Contrast adjustment of Composite & S-Video form¡¯s signal.
„ BR
: Brightness adjustment of Composite & S-Video form¡¯s signal.
„ ACC_SAT
„ TINT
: The color sense adjustment of Composite & S-Video form¡¯s signal.
„ SATCb
: The blue color sense adjustment of Component & RGB form¡¯s signal.
„ SATCr
: The red color sense adjustment of Component & RGB form¡¯s signal
„ CIPTNT
: The color sense adjustment of Component & RGB form¡¯s signal.
„ CIPBR
: The brightness adjustment of Component & RGB form¡¯s signal.
„ KILVL
„ LDLY
: The delayed time adjustment of brightness signal.
„ PKCOR
„ FB_GAIN
SERVICE MANUAL (BSV-4251 BSV-4251A )
VPC3230-SUB MENU
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 26/75
VPC3230-SUB MENU
„ CT
: The contrast adjustment of Composite & S-Video form¡¯s signal.
„ BR
: The brightness adjustment of Composite & S-Video form¡¯s signal.
„ ACC_SAT
„ TINT
: The color sense adjustment of Composite & S-Video form¡¯s signal.
SERVICE MANUAL (BSV-4251 BSV-4251A )
„ SATCb
„ SATCr
„ CIPTNT
„ CIPBR
„ KILVL
„ LDLY
„ PKCOR
„ FB_GAIN
: The blue color sense adjustment of Component & RGB form¡¯s signal.
: The red color sense adjustment of Component & RGB form¡¯s signal.
: The color sense adjustment of Component & RGB form¡¯s signal.
: The brightness adjustment of Component & RGB form¡¯s signal.
: The delayed time installation of brightness signal.
ADC MENU
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 27/75
ADC MENU
„ Red, Green, Blue Gain
: Control ADC input range (Contrast) of each respective channel.
SERVICE MANUAL (BSV-4251 BSV-4251A )
„ Red, Green, Blue Offset
: Control dc offset (Brightness) of each respective channel.
„ Current
: Installation of PLL Part VCO Current. (For test)
„ VCO
: Installation of PLL Part VCO Range (For test)
„ Pr, Y, Pb Gain
: Contrast adjustment of Component2 Pr, Y, Pb signal.
„ Pr, Y, Pb Offset
: Brightness adjustment of Component2 Pr, Y, Pb signal.
„ TTX Phase
: It is not useful mode.
„ TTX Contrast
: It is not useful mode.
HEATRUN MENU
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 28/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
HEATRUN MENU
„ 1. Auto Run
: It is the mode to change the heatrun pattern as a certain time interval.
„ 2. Luma Ramp (16 Step)
: It is gray pattern of 16 Step.
„ 3. Luma Ramp (128 Step)
: It is gray pattern of 128 Step.
„ 4. White 16
: It is low Gray pattern.
„ 5. White 240
: It is high gray pattern.
„ 6. Color Bar
: It is color Bar Pattern.
„ 7. RGB Ramp (32 Step)
: It is RGB Ramp pattern of 32 Step.
VERSION MENU
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 29/75
VERSION MENU
„ Version
: It is to show the Firmware Version.
SERVICE MANUAL (BSV-4251 BSV-4251A )
„ Release
: It is to show the date of Firmware revision.
„ Panel Used Time
: It is to show the used time of Panel.
„ Panel Name
: It is to show the name of the PDP.
SETUP MENU
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 30/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
SETUP MENU
„ 1. TTX Language
: Installation of initial language of the TTX.
„ 2. Video
: Video format per country and it is composed of Normal, NTSC, PAL N, M
„ 3. Protocol
: Installation of communication protocol for remote control.
„ 4. LOGO
: Installation to show company logo on the screen when power ¡°On¡±(ON/OFF).
DESCRIPTION OF VSC FUNCTIONS
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 31/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
PSM (Picture Status Memory)
Function to adjust picture status to an optimal condition in accordance with the type of program being
viewed (standard, moving picture, movie, muted, game).
SSM (Sound Status Memory)
Function to adjust sound status to an optimal condition in accordance with the type of program being
viewed (standard, music, movie, news).
ARC (Aspect Ratio Control)
Function to adjust the picture size. (16:9. enlargement 1, enlargement 2, panorama, 4:3)
Panorama
Function to prevent pictures recorded in the 4:3 format from being stretched to the extreme left and right
when played on a 16:9 display. Since the focus of the camera is concentrated on the center, it naturally
enlarges the picture within the outer perimeter of the screen without expanding the central area.
PIP (Picture In Picture)
Function to enable the simultaneous viewing of two pictures by displaying a small sub-frame within the
main picture. The main picture may be viewed with multiple types of input source (Analog/Digital RGB,
composite, S-Video, component), while the sub-frame is only available in composite, S-Video or
component (480i).
PBP (Picture By Picture) ,Twin Picture
Function to assign two separate signals onto a single screen, thereby enabling the viewer to
simultaneously watch different pictures on each half of the display.
PIP Swap Simultaneous Conversion Between Sub and Main Pictures.
Function to convert between the sub-frame and main picture being watched simultaneously.
PIP Sound Swap Simultaneous Conversion Between sub and Main Picture Audio
Function to convert between simultaneous audio streams from the sub-frame and main picture being
viewed.
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 32/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
EQUALIZER
Function to control sound according to frequency. (100Hz, 300Hz, 1KHz, 3KHz, 10KHz)
AVL (Auto Volume Leveler)
Function to automatically adjust varying sound levels from each individual broadcasting company to an
appropriate volume, in case of watching a television connected to external equipment. This allows to
viewer to enjoy a comfortable and stable sound level even when changing the channel.
CIRCUIT OPERATION & WAVEFORM
VPC3230D (Video Processor)
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 33/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
Converts analog pictures (including Composite, S-Video, Component (480i) or the like) to Y-UV
digital pictures. Compatible with various TV formats of NTSC, PAL, SECAM, etc.
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 35/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
AD9883 (A/D Converter)
Converts an analog RGB signal to a process able digital signal. Converts a component signal (480p,
720p, 1080i) to a digital signal and transmits it to PW565 (Scaler).
U2 (AD9883)_#30_ Hsync0 U2 (AD9883)_#31_Vsync0
U2 (AD9883)_#67_DATACK U2 (AD9883)_#64_VSOUT
U2 (AD9883)_#65_SOG U2 (AD9883)_#66_HSOU T
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 36/75
U1 (LM2937)_#3_ VO
SERVICE MANUAL (BSV-4251 BSV-4251A )
PW565 (Scaler)
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 37/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
Receives, at the same time, a video signal from VPC3230, an Analog/Digital RGB signal and a
Component signal, which are converted at AD9883 and THC63DV151, adjusted to a PDP display,
and transmitted to a PDP module. In particular, it receives any PC signal input at various scanning
rates and performs scaling to adjust to PDP resolution.
RP12 (R-ARRAY)_#1_DEN RP12 (R-ARRAY)_#4_DCLK
RP12 (R-ARRAY)_#3_DVS RP12 (R-ARRAY)_#2_DHS
MSP3450 (Sound Processor)
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 38/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
Receives and converts any Sound IF signal from a TV Tuner to a general audio signal (LCD TV).
Also, outputs the desired input signal out of many audio input signal options, and produces a woofer
signal or Headphone signal as well as a general Speaker signal (LCD TV).
5. If 5Volt Mnt “Low” or AC-Det “Low”, immediately Display Enable “Off” and
SERVICE MANUAL (BSV-4251 BSV-4251A )
VSC POWER SEQUENCE
then VaVs “Off”, Relay “Off”.
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 42/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
PSU POWER SEQUENCE
[POWER DGK-420W]
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 43/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
VOLTAGE & W/B ADJUSTMENT
Power PCB Assy Voltage Adjustment
1-1-1. Va Adjustment (Address Voltage Adjustment)
(°¡) Connect pin 9,10 of CN806 to(+) jack of D.M.M
(³ª) After turning the VR2 (Va Adj),Voltage of D.M.M adjustment as same as Va voltage which on
Label of panel right/bottom.(Deviation : ± 0.5V)
1-1-2. Vs Adjustment
(°¡) Connect pin 1~3 of CN806 to (+) jack of D.M.M
(³ª) After turning the VR3(Vs Adj),voltage of D.M.M adjustment as same as Vs voltage which
indicated on Label of panel right/bottom.(Deviation : ± 0.5V)
Refer to Typical Voltage
1. Va : 65V
2. Vs : 190V
¡Ø Replace PDP Module or Power Board, adjust certainly Power PCB Ass’y Voltage
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 44/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 45/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
2. W/B adjustment
2-2. Color temperature (White Balance) adjustment
1) How to enter Factory mode for adjustment of White Balance
(1) PDP TV Power ¡°On¡± --> Input select key on Remote control.
(2) Choose composite first and then PDP TV Power ¡°Off¡±.
(3) PDP TV Power ¡°Off¡± and INFO on the R/C ==> ERASE ==> ENTER Key
2) For COMPOSITE adjustment (manual adjustment)
(1) Signal Generator supply the pattern of above picture. (Timing ¢¡ 386, Pattem ¢¡ 10)
(2) After movement to 2.color control on Factory Mode2, move to sub menu as choice of volume
.
button
(3) After check the Brightness ¢¡ 50, Contrast ¢¡ 90, choose the Sub-Brightn ess.
(4) Zero calibration¡¯s execution of CA-100 and the sensor should be closed to surface of PDP
(2) After movement to 1.calibration on Factory Mode, move to sub menu as choice of volume button.
(3) After movement to 2. DTV Calibration, choose it with volume button.
(4) If Enter key, it starts the calibratio
4) For PC adjustment
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 47/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
(1) Signal Generator supply the pattern of above picture.
Timing ¢¡ 313, Pattem ¢¡ 609 (1024 x 768, 60Hz)
(2) After movement to 1.calibration on Factory Mode, move to sub menu as choice of volume
button
(3) After movement to 2. PC Calibration, choose it with volume button.
(4) If Enter key, it starts the calibration automatically
.
How to exit the Factory Mode
INFO ¢¡ LAST ¢¡ ERASE ¢¡ ENTER Key
5) Adjustment verification
Adjustment as volume ¡°0¡± and then 4 times of Enter key
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 48/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
SAFETY PRECAUTIONS
( MODULE USE AND CONSIDERATIONS IN SERVICING)
PDP Module is a display device to be divided into a Panel part and a Drive part. The Panel part consists of
Electrodes, Phosphor, various dielectrics and gas, and the Drive part includes electronic circui try and PCB.
When using / handling this PDP Module, pay attention to the below warning and cautions.
Indicates a hazard that may lead to death or injury if the warning is ignored and the product is handled
incorrectly.
Indicates a hazard that can lead to injury or damage to property if the caution is ignored and the product is
handled incorrectly.
■. WARNING
(1) Do not supply a voltage higher than that specified to this product. This may damage the product and may
cause a fire.
(2) Do not use this product in locations where the humidity is extremely high, where it may be splashed with
water, or where flammable materials surround it.
Do not install or use the product in a location that does no satisfy the specified environmental conditions.
This may damage the product and may cause a fire.
(3) If a foreign substance (such as water, metal, or liquid) gets inside the product, immediately turn off the
power.
Continuing to use the product, it is may cause fire or electric shock.
(4) If the product emits smoke, and abnormal smell, or makes an abnormal sou nd, immediately turn off the
power.
Continuing to use the product, it may cause fire or electric shock.
(5) Do not disconnect or connect the connector while power to the product is on. It takes some time for the
voltage to drop to a sufficiently low level after the power has been turned off.
Confirm that the voltage has dropped to a safe level before disconnecting or connecting the connector.
(6) Do not pull out or insert the power cable from/to an outlet with wet hands. It may cause electric shock.
(7) Do not damage or modify the power cable. It may cause fire or electric shock.
(8) If the power cable is damaged, or if the connector is loose, do not use the product: otherwise, this can
lead to fire or electric shock.
(9) If the power connector or the connector of the power cable becomes dirty or dusty, wipe it with a dry cloth.
Otherwise, this can lead to fire.
(10) PDP Module uses a high voltage (Max.450V dc). Keep the cautions concerning electric shock and do
not touch the Device circuitry when handling the PDP Unit. And because the capacitor of the Device
circuitry may remain charged at the moment of Power OFF, standing by for 1 minute is required in order
to touch the Device circuitry.
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 49/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
CAUTIONS
(1) Do not place this product in a location that is subject to heavy vibration, or on an unstable surface such as
an inclined surface. The product may fall off or fall over, causing injuries.
(2) Before disconnecting cable from the product, be sure to turn off the power. Be sure to hold the connector
when disconnecting cables. Pulling a cable with excessive force may cause the core of the cable to be
exposed or break the cable, and this can lead to fire or electric shock.
(3) This product should be moved by two or more persons. If one person attempts to carry this product alone,
he/she may be injured.
(4) This product contains glass. The glass may break, causing injuries, if shock, vibration, heat, or distortion
is applied to the product.
(5) The temperature of the glass of the display may rise to 80°C or more depending on the conditions of use.
If you touch the glass inadvertently, you may be burned.
(6) If glass surface of the display breaks or is scratched, do not touch the broken pieces or the scratches with
bare hands. You may be injured.
(7) PDP Module requires to be handled with care not to be touched with metal or hard material s, and must
not be stressed by heat or mechanical impact.
(8) There are some exposed components on the rear panel of this product. Touching these components may
cause an electric shock.
(9) When moving the product, be sure to turn off the power and disconnect all the cables. While moving the
product, watch your step. The product may be dropped or all, leading to injuries of electric shock.
(10) In order to protect static electricity due to C-MOS circuitry of the Drive part, wear a wrist band to protect
static electricity when handling.
(11) If cleaning the Panel, wipe it with a soft cloth moistened with water or a neutral detergent and squeezed,
being careful not to touch the connector part of the Panel. And don’t use chemical materials like thinner
or benzene.
(12) If this product is used as a display board to display a static image, “image sticking” occurs. This means
that the luminance of areas of the display that remain lit for a long time drops compared with luminance
of areas that are lit for a shorter time, causing uneven luminance across the display.
The degree to which this occurs is in prop ortion to the luminance at which the display is used. To prevent
this phenomenon, therefore, avoid static images as much as possible and design your system so that it
is used at a low luminance, by reducing signal level difference between bright area and less bright area
through signal processing.
(13) Because PDP Module emits heat from the Glass Panel part and the Drive circuitry, the environmental
temperature must not be over 40°C.
The temperature of the Glass Panel part is e spe cially high owing to heat from internal Drive circuitry. And
because the PDP Module is driven by high voltage, it must avoid conductive materials.
(14) If inserting components or circuit board in order to repair, be sure to fix a lead line to the connector
before soldering.
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 50/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
(15) If inserting high-power resistor(metal-oxide film resistor or metal film resistor) in order to repair, insert it
as 10mm away as from a board.
(16) During repairs, high voltage or high temperature components must be put away from a lead line.
(17) This is a Cold Chassis but you had better use a cold transformer for safety during repairs. If repairing
electricity source part, you must use the cold transformer.
(18) Do not place an object on the glass surface of the display.
The glass may break or be scratched.
(19) This product may be damaged if it is subject to excessive stresses (such as excessive voltage, current,
or temperature).
The absolute maximum ratings specify the limits of these stresses.
(20) The recommended operating conditions are conditions in which the normal operation of this product is
guaranteed. All the rated values of the electrical specifications are guaranteed within these conditions.
Always use the product within the range of the recommended operating conditions. Otherwise, the
reliability of the product may be degraded.
(21) This product has a glass display surface. Design your system so that excessive shock and load are not
applied to the glass. Exercise care that the vent at the corner of the glass panel is not damaged.
If the glass panel or vent is damaged, the product is inoperable.
(22) Do not cover or wrap the product with a cloth or other covering while power is supplied to the prod uct.
(23) Before turning on power to the product, check the wiring of the product and confirm that the supply
voltage is within the rated voltage range. If the wiring is wrong or if a voltage outside the rated range is
applied, the product may malfunction or be damaged.
(24) Do not store this product in a location where temperature and humidity are high. This may cause the
product to malfunction. Because this product uses a discharge phenomenon, it may take time to light
(operation may be delayed) when the product is used after it has been stored for a long time. In this case,
it is recommended to light all cells for about 2 hours (aging).
(25) This product is made from various materials such as glass, metal, and plastic. When discarding it, be
sure to contact a professional waste disposal operator.
(26) If faults occur due to arbitrary modification or disassembly, Erae Electronics is not responsible for
function, quality or other items.
(27) Use of the product with a combination of parameters, conditions, or logic not specified in the
specifications of this product is not guaranteed. If intending to use the product in such a way, be sure to
consult Erae Electronics in advance.
(28) Within the warranty period, general faults that occur due to defects in components such as ICs will be
rectified by Erae Electronics without charge. However, IMAGE STICKING due to misapplying the above
(12) provision is not included in the warranty. Repairs due to the other faults may be charged for
depending on responsibility for the faults.
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 51/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 52/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
TROUBLE SHOOTING
1.hecking for no Picture
C
A screen doesn if display at all and c
(1) Check whether the CTRL B/D LED(D1~D4) is turned on or not.
(2) Check the power and signal cable of CTRL B/D.
(3) X B/D, Y B/D, Z B/D is well plugged in.
(4) Check the connection of X B/D, Y B/D and Z B/D
(5) Measure the output wave of X, Y, Z B/D
and find the trouble of B/D by comparing the output wave with b
- Measure Point fo Y B/D : TP (Connector P4 80 pin)
- Measure Point fo Z B/D : Connection part of panel (SUS_OUT)
- Measure Point fo X B/D : L1(RIGHT), L2(LEFT BOTT
(6) C
heck the SCAN(Y side) IC
(7) C
heck the DATA(X side) COF IC
(8) Replace the CTRL B/D.
2. Hitch Diagnosis Following Display Condition
-1. 4/7 or 3/7 of the screen doesn’t be shown
2
(1) Confirm the power connector of X B/D is well plugged in which is correspond to not showing screen.
(2) Confirm the connector that is connected between CTRL B/D and X B/D correspond to not showing
part.
(3) Re relevant X B/D.
eplac
ondition of black pattern or power off.
to CTRL B/D.
with oscilloscope(more than 200MHz)
elow figure.
OM)
Relationship between screen and X B/D
Display X B/D
Left o 4/7
f the Screen
Right of the Screen 3/7
Right X B/D
Left X B/D
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 53/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
¡Ø Screen Display Form
2-2. The screen doesn’t be shown as Data COF
(Include not be shown part of Data COF quantity or a part)
(1at the screen is not be shown as data
) The problem between Data COF and X B/D is more possible th
COF.
(2) Confirm the connector of Data COF is well connected to X B/D. Correspond to the part that screen is
not show
(3) Confirm whether the Data COF is failed and replace X B/D
Example of the screen display form
※
(Anything of the 7 Data COF can be shown beside below pictures)
ing
How to examine Data COF IC
※
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 54/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
2-3. It Generates Unusual Pattern of Data COF IC unit
(1) In case of generating unusual pattern of Data COF IC unit as belo
that is input into Data COF IC
(2) In case of <case 1, 2, 3>
- confirm the connection of Dat
- replace the relevant X B
(3) I
n case of <case 4, 5>
- confirm the connector that is
- Replace relevant XB
Screen Display Form
※
/D or CTRL B/D
a COF connector
/D
connected from CTRL to X B/D
w picture, there is problem in the check
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 55/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
2-4. Regular Stripe is Generated about the Quantity of one Data COF IC or more
(1) In case of generating regular stripe about the quantity of one Data COF IC, there is problem at the
output of outputflatworm of X B/D
In case of generating regular stripe about the quantity of two Data COF IC, that means the data
which is conveyed from CTRL B/D doesn’t conveyed well.
(2) C
onfirm the XB/D connection connector plugged in well.
Correspond to unusual screen.
(3) R
eplace relevant XB/D or CTRL B/D.
※elationship between screen and X B/D
R
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 56/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
Display X B/D
Left Bottom of the Screen 4/7 Right X B/D
Right Bottomreen 3/7 Lef/D of the Sct X B
Screen Display Form ※
2-5. The screen display has a problem for Scan FFC.
(1) It’s may be a problem between Scan FFC and Y B/D.
(2) Check the connection of Y B/D and Scan COF.
(3) If the Scan IC is failed, replace the Y DRV B/D.
.
Screen Display Form
Check a method of SCAN IC
※
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 57/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
-6. The screen has a vertical line with regular gap.
2
(A vertical stripe flash at especial color)
(
1) This is a problem about control B/D.
(
2) Replace Control B/D.
※
Screen Display Form
2-7. A data copy is happened into vertical direction
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 58/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
(1) In this case, it’s due to incorrect marking of scan wave.
(2) Replace a Y DRV B/D or Y SUS B/D.
※ Screen Display Form
2-8. The screen has one or several vertical line
(1) In this case, It isn’t a problem about controller B/D or
(2) It may cause followings.
- It’s out of order a panel
COF FPC attached panel
COF attached panel
(3) R
- Open or short of DATA
- It’s out of order a DATA
eplace Module.
X B/D.
- 9. The screen has one or several horizontal line
2
(1) In this case, it isn’t a problem about controller B/D or X B/D
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 59/75
.
SERVICE MANUAL (BSV-4251 BSV-4251A )
(2) It may cause followings.
- It’s out of order a panel
- Open or short of SCAN F
- It’s out of order a SCAN IC attach
(3) Replace Y DRV B/D
2-10. The screen displays input signal pattern but the brightness is dar
(1) In this case, Z B/D operation isn’t complete.
(2) Check the power cord of Z B/D.
(3) Check the connector of Z B/D and Controller
(4) Replace the Controller B/D or Z B
-1r partially on full white screen or happens
21. The screen displays other colo
discharge partially on full black screen.
(1)e.
(3) Measure each output wave with oscilloscope(more than
Adjust the Y B/D set up(Test-up:B/C[¥s/¥s])/setdown(Testdown: D[¥s]) and Z B/D
- Measuring Point of Y B/D : P4 (Connector P4 36 pin)
-
Check the declination of Y B/D set up, set down wav
(2) Check the declination of Z B/D ¢«ramp wave.
figure data.
ramp(Tramp
Measuring Point of Z B/D : B37 (SUS_OUT)
:F/G[¥s/¥s]) declination by changing VR1/VR2/VR3.
PC attached panel
ed panel
/D.
B/D.
k
200MHz) and compare the data with below
. A center of screen is darker than a edge of screen at full white pattern.
2-12
(1) In this case, it’s a problem about Z B/D ramp wave.
(2) Check the connection cable of Z B/D and CTRL B/D.
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 60/75
(3) Replace the Z B/D.
SERVICE MANUAL (BSV-4251 BSV-4251A )
-13. It doesn’t display a specified brightness at specified color
2
(1) Check the connector of CTRL B/D input signal.
(2) Replace the CTRL B/D.
-1. No Power
3
Nothing output
of image
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 61/75
.
Check Input of AC
(90V ~225V)
Normal
Check ST-BY LED ON
Main S/W ON.
Normal
SERVICE MANUAL (BSV-4251 BSV-4251A )
Abnormal
Abnorma l
Connect plug with the set.
Check AC Line Fuse
Check LED YELL OW
Sub S/W ON
Normal
Check a connective condition
and various connect or.
-2. No Sound
3
heckaconnective
C
condition of power
cable
-3. No Video
3
Abnormal Abnormal
Check voltage
of sound terminal .
Check OPEN With
CN806,CN13
C
heck the Vs Voltage
IC1rt)
5,IC16(PSU Pa
and VSC Part Q30
Check Open with
FuseF1 Fuse
Replace
IC15,IC16,Q30
Check connection
line of speake r.
Abnormal Picture
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 62/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
Input PC,DTV Signal
Normal
Input DV D Signal
Normal
Input Tuner-CVB S,
CVBS,F/H SCART,S-Video
Signal
Normal
Abnormal
Input F/SCART RGB
Signal
Abnormal
Abnorma l
AbnormalAbnormal
Check BA7657
Check VPC3230 Dual
U39,U41
Check CX
U3
Check BA7657
U28
U8
A2089Q
Check AD9883
U2
Check PW565
RP12~18
Check SiI164
U48
Check Cable
3-4. No Sound
Check
Input
Jack.
coector
Spo
Check nn
eaker t
set.
Check
CXA2089Q
U3
Check
MSP3450G
U45
Check
TDA7495S
U14
IMAGE STICKING CHARACTERISTICS
1) I
mage Sticking
The fluorescent substance used in the plasma module loses its brightness with the lapse of lighting time.
This deteriorati
and cornes to be recognized as image sticking.
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 63/75
on in brightness apprears to be a difference in brightness in relation to the surroundings,
In other words, the image sticking is defined as follows: when the same pattern(of the fixed display)is
displayed for a long times, a difference in brightness is caused around the lighting area and non-lighting
area due to deterioration in the fluorescent substance.
When the present pattern is changed over to another one, the boundary comes to be seen between the
lighting area and non-lighting area due to difference i
changeover. If this conditions is accumulated, the boundary or image sticking comes to be seen with the
naked eyes.
2) S in brightness
ecular change
The life of brightness, defined as the reduction to half the initial level, is more than 25 thousand hours on
average.
Conditions: All white (100% white) input at an ambient temperature of 25℃.
However, this lifetime is n
the data for refernce.
3) W
arrenty
Image sticking and faults in brightness and picture elements are excluded from the warranty objects.
4) Cause of deterioration in brightness
A major possible cause of deterioration in brightness is damage in the fluorescent substance due to
impact caused by ions generated a
5) P
ractical value for Image sticking
The relationship between intergrated lighting time and brightness in this plasma module is described in
the attached material. In particul
hours in the initial period. In the initial period, the fixed display of patterns particularly tends to cause
image sticking. The practical value for image sticking is difficult in concrete numerals. As described
below, you are advised to take proper measures to make the occurrence of image sticking as slow
possible.
6) Peasures taken to relieve image sticking
roposed m
So long as there is the reduction of brightness in the fluorescent substance, it is impossible to the avoid
the occurrence of image sticking .Therefore, to relieve
image input that may ensure reluctance to the generation of the difference in brightness reduction among
the displayed dots.
The images from TV broadcasting involve a high rate of motion picture displays. Therefore, there is less
change of being a
patterns are displayed, they generally last for a few minutes. Since the same pattern is less liable to be
displayed, there is almost no influence toward image sticking.
If the fixed patterns tend to be displayed for a long time, how
tween the lighting and non-lighting areas, this causing a difference in brightness as a result. In this
be
document , we offer you some proposals of installation, paying attentions to the two points: the reduction of
difference of brightness achieved by intergrated lighting time leveling and the method of edge smearing to
make image sticking hard to be discerned.
The result from these proposals can, however, greatly depend on the contents of images and operating
environment.
Therefore, we
perating environment.
o
Example of Poposal 1: The display position is moved while the fixed display pattern is changed over, or it is
scrolled during the displa
Example of Proposal 2: If possible, a pattern of complementary color is incorporated (for intergrated time
leveling).
Example of Proposal 3: The fixed pattern and the motion picture display are reciprocally exchanged, in
cause of difference in brightness reduction among the cells. Even when the fixed
consider that it is essential to take the suitable measures in consideration of the customer’s
ot a guarantee value for life and brightness. It should be recognized simply as
y.
SERVICE MANUAL (BSV-4251 BSV-4251A )
n brightness in the pattern shown shorty before
t the time of plasma discharges.
ar, the deterioration in brightness tends to be accelerated up to 100
image sticking ,we offer you a method of entering an
ever, there occurs a substantial imbalance
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/1 0/23 64/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
order to minimize display period of the fixed pattern.
Example of Proposal 4: During operation, the brightness of screen is suppressed as low as possible.
For the display patterns, characters are indicated n
colored ground (mixture of R, G,B recommended).
ot on the black ground (non-picture area) but on the
ISM Mode(Image Sticking Minimization Mode)
Apart from the above proposal, This module has been equipped with a special method that minimizes the
image sticking phenomenon. When in the fixed pattern display mode, the module decreases the brightness
over a period of 10 minutes with small steps. The figure blow shows that the decrease in brightness is so
small the user will not notice.
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 65/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
The basis of the evaluation was while the ISM Mode in he module was operating, the brightness decrease
about
55 % o
ISM operational conditions
1. Detective deviation : The
minutes.
2. Regard
f its initial value at the white window pattern ( 1/25 of full white pattern )
change of APL Data is no less than ±4 and it will remain for more than 5
less of time, it will not operate where the display load is over 50%.
t
SCHEMATIC & PRINTED CIRCUIT BOARD & EXPLODE VIEW
PSU(DGK-420W) TOP
¡á
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 66/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
■ PSU(DGK-420W) BOTTOM
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 67/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
EXPLODED VIEW PARTS LIST
No Part no Description
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE
BSV-4251/4251A RD(1) 00 03/10/23 68/75
SERVICE MANUAL (BSV-4251 BSV-4251A )
2 S150110021 MAIN ASSY EPT-4200A(PAL)
3 S15012G021 FRONT FRAME ASSY EPT-4200A(PAL-STD)
4 S15013F016 FRAME FILTER ASSY EPM-4200A(MONITOR-STD)
5 S15014B016 FRAME ASSY EPM-4200B(MONITOR-STD)
2 S15012C021 JACK HOUSING ASSY EPT-4200(PAL)
4 S15014A021 FRONT ASSY EPT-4200A(PAL)
3 S15013C016 HEAT SINK ASSY EPM-4200A
3 S15013B016 MODULE ASSY EPM-4200A
2 S15012F016 AC IN-LET ASSY EPM-4200A
3 S150120036 VSC BOARD ASSY(TOP) EPT-4200AP
2 S150113036 VSC BOARD ASSY EPT-4200AP(PW565)
4 S150130036 VSC BOARD ASSY(BOTTOM) EPT-4200AP
6 S15015B021
2 S150114036 TUNER BOARD ASSY EPT-4200AP(PW565)
3 S150121036 TUNER BOARD ASSY(SMD) EPT-4200AP(PW565)
2 S150134021 AUDIO OUT B/D ASSY EPM4200A
2 S150112021 POWER S/W ASSY EPT-4200A(PAL-STD)
3 S150132009 POWER S/W PCB ASSY EPM-420AN
5 S150141021
1 S150111021 PACKING ASSY EPT-4200A(PAL)
2 S15012F021 ACCESSORY ASSY EPT-4200A(PAL)
3 S15013C021 REMOCON ASSY EPT-4200A(PAL)
3 71BELP324 JACK HOUSING AL/PAL TV
3 71BELP315 HEAT SHINK AL 28X28X13
4 71BELP1801 HEAT SINK ASSY AL+SPTH
3 71FELP314 SHIELD VSC-B SPTH-C, 0.5T
2 71FELP313 SHIELD VSC-T SPTH-C, 0.3T
2 70AELM310 BUTTON POWER ABS
2 71AELP126 BRKT SUPP EGI/1T
2 71AELP288 BRKT A EGI/1T
2 71AELP289 BRKT B EGI/1T
2 71AELP310 BRKT IN-LET EGI/1T
2 71AELP311 BRKT VSC EGI/1T
2 71BELP287 BACK AL 1.5T PAINT/KK VERSION
6 71AELP115 BRKT STAND EGI 1.5T
6 71AELP118 BRKT C EGI 1T
6 71AELP284 BRKT D EGI/1T/EPM-420KK
5 71AELP117 BRKT FILTER EGI 1T
6 77A1010540 BLACK SH B FELT 1TX10X540
6 77A1010950 BLACK SH A FELT 1TX10X950
6 71BELP285 FRAME X AL
6 71BELP286 FRAME Y AL
5 70EELM311 LENS PMMA
5 70PELM3298 FRONT A PC/ABS/SILVER/DCDI/STAND BY/7KEY/EPM-4200A
5 72BELR111 PROTECTOR SILICON/25X25X45
6 70AELM460
6 73DELi046 INSULATION-BUTTON PVC(25X15X0.3T)
7 70AEPM1173
4 71HELP246 SUPPORT Y SPC, 1.6t
4 70AELM310 BUTTON POWER ABS
OSD PCB ASSY EPT-4200A(TV用_7KEY)
OSD ASSY EPT-4200A(TV用_7KEY)
BUTTON CTRL ABS(7KEY)/EPT-4200(TV用)
LED GUIDE 4MMX5ΦX3P
MODEL NAME DOCUMENT NO REVISION NO REVISION DATE PAGE