Foodservice Equipment Specialists
P.O. Box 880 Saco, ME. / U.S.A. 04072 877-854-8006 (FAX) 207-283-8080
OPERATIONS AND MAINTENANCE PROCEDURES
CONVEYOR TOASTER MODEL - JT1, JT1H & JT1-B
FOR SERVICE ASSISTANCE
U.S. AND CANADA CALL: 1-877-854-8006 24 HOURS/DAY 7 DAYS/WEEK
TABLE OF CONTENTS
ASSEMBLY AND INSTALLATION |
PAGE 1 |
ELECTRICAL INSTALLATION |
PAGE 1 |
POWER SAVER FEATURE |
PAGE 2 |
TOASTING PROCEDURE |
PAGE 2 |
CLEANING (DAILY & WEEKLY) |
PAGE 2 |
GENERAL MAINTENANCE |
PAGE 3 |
TROUBLESHOOTING GUIDE |
PAGE 4 |
SPARE PARTS LISTINGS |
PAGE 5 |
OM-001
5-20-05 RJB
Page 1
OPERATIONS AND MAINTENANCE PROCEDURES
CONVEYOR TOASTER MODEL – JT1, JT1H & JT1-B
UNCRATING AND INSPECTION
Unpack the unit and components from the shipping container. Remove all visible packing materials including those that may be inside the toasting chamber. If damage is discovered, file a claim immediately with the carrier that handled the shipment.
ASSEMBLY AND INSTALLATION
Toasters are shipped fully assembled and ready to plug into a matching outlet specified for its specific voltage and amperage rating. Removal or replacement of the power cord and plug will VOID the warranty. For assistance, contact the Belleco, Inc. Service Group at 1-877-854-8006.
CAUTION – During installation: Do not place on surfaces or near walls, partitions or kitchen furniture and the like – unless they are made of non-combustible material or clad with non-combustible heat-insulating material, and pay attention to fire prevention regulations.
"Bread may burn. Therefore toasters must not be used near or below curtains and other combustible materials. They must be watched."
"Le pain peut bruler, aussi les grille-pain ne doivent-ils pas etre utilizes a proximite ou sous des rideaux ou autres materiaux combustibles. Ils doivent etre suveilles."
ELECTRICAL INSTALLATION
WARNING – Disconnect the toaster from its power source before installing or removing any parts.
WARNING – NEVER operate any piece of equipment without proper GROUND connection. Improper grounding may result in serious personal injury or could be fatal!
PAGE 2
OPERATIONS AND MAINTENANCE PROCEDURES CONVEYOR TOASTER MODEL – JT1, JT1H & JT1-B
POWER SAVER FEATURE
All toasters come equipped with a Rotary Power Saver Switch. To operate, turn clockwise or counterclockwise to place the toaster in the following modes:
FULL POWER – In this position, the toaster is at full heat and ready for toasting.
OFF – There are two OFF positions provided so that a single rotation in either direction will turn the toaster OFF.
STANDBY – When in STANDBY, overall electrical consumption is reduced by 75%. There is just enough heat to warm the inside toasting chamber walls and reflectors. When switched to the FULL POWER position, a minimal amount of time is required to reach toasting temperatures.
TOASTING PROCEDURE
A. BREAD TOASTING
•Turn the Power Saver knob to the “Full Power” position.
(Model JT1H Set top and bottom On/Off Rocker Switches to the ON position)
•Set the Conveyor Speed Control knob to 50.
•Allow 10 – 15 minutes to heat from cold.
•Place a sample of the desired product on the Conveyor Belt to test the settings.
•If toasting is too light, turn the Speed Control counterclockwise to a slower speed.
•If toasting is too dark, turn the Speed Control clockwise to a faster speed.
Buns, Bagels and English Muffins may be tested the same as above but with either Variable Heat Control reduced. It is recommended by Belleco, Inc. that such one sided toasting be done cutside up to prevent lines on the toasted surface.
CLEANING PROCEDURE
Preventive Maintenance programs on your toaster will provide many years of production at full capacity. Lack of Preventive Maintenance can shorten the life cycle of the toaster and/or result in reduced capacities. The following cleaning guidelines should be performed as shown:
WARNING – ALWAYS DISCONNECT YOUR TOASTER FROM POWER PRIOR TO CLEANING OR MAINTENANCE
Loading...