Beko WTV77111BW01 User manual
Washing Machine
User Manual
Waschmaschine
Bedienungsanleitung
WTV77111BW01
EN / DE
Document Number :
2820528612_EN / 04-06-20.(8:56)
This product was manufactured using the latest technology in environmentally friendly conditions.
1
General safety nstructons
This section includes security instructions which may help prevent
the injuries and material damage risks. All kinds of warranties shall
be invalid if these instructions are not observed.
1.1 Lfe and property safety
u
Never place the product on a carpet-covered floor. Electrcal parts
wll get overheated snce ar cannot crculate from under the devce.
Ths wll cause problems wth your product.
u
Unplug the product f t s not n use.
u
Always have the nstallaton and reparng procedures carred
out by the Authorsed Servce Agent. The manufacturer shall
not be held lable for damages that may arse from procedures
carred out by unauthorsed persons.
u
The water supply and dranng hoses must be securely fastened and
reman undamaged. Otherwse, water leak may occur.
u
Whle there s stll water nsde the product, never open the
loadng door or remove the flter. Otherwse, rsk of floodng
and njury from hot water wll occur.
u
Do not force open the locked loadng door. Door can be opened a few
mnutes after the washng cycle ends. In case of forcng the loadng
door to open, the door and the lock mechansm may get damaged.
u
Use detergents, softeners and supplements sutable for automatc
washng machnes only.
u
Follow the nstructons on the label of textles and the detergent
package.
u
The water supply pressure requred to run the product s between 1
to 10 bars (0.1 – 1 MPa).
u
Do not use old or used water nlet hoses on the new product. It may
cause stans on your laundry.
1.2 Chldren's safety
u
Ths product can be used by the chldren who are at the age of 8 and
over and the people whose physcal, sensory or mental sklls are not
fully developed or who do not have necessary requred experence
and knowledge as long as they are supervsed or traned about the
safe use of the product and ts rsks. Chldren should not play wth the
devce. Cleanng and mantenance works should not be performed
by chldren unless they are supervsed by someone. Chldren of less
than 3 years should be kept away unless contnuously supervsed.
Washing Machine / User Manual
3 / EN
u
Packagng materals may be dangerous for the chldren. Keep
packagng materals n a safe place away from reach of the chldren.
u
Electrcal products are dangerous for the chldren. Keep the chldren
away from the product when t s n use. Do not allow them to play
wth the product. Use chld lock to prevent chldren from ntervenng
wth the product.
u
Do not forget to close the loadng door when leavng the room where
the product s located.
u
Store all detergents and addtves n a safe place away from the
reach of the chldren by closng the cover of the detergent contaner
or sealng the detergent package.
1.3 Electrcal safety
u
If the product has a falure, t should not be operated unless t s
repared by the Authorsed Servce Agent. Rsk of electrc shock!
u
Ths product s desgned to resume operatng n the event of
powerng on after a power nterrupton. If you wsh to cancel the
programme, see "Cancellng the programme" secton.
u
Plug the product nto a grounded outlet protected by a 16 A fuse. Do
not neglect to have the groundng nstallaton made by a qualfed
electrcan. Our company shall not be lable for any damages that
wll arse when the product s used wthout groundng n accordance
wth the local regulatons.
u
Do not wash the product by sprayng or pourng water onto t! Rsk of
electrc shock!
u
Never touch the power cable plug wth wet hands! Do not grab the
power cord to unplug the machne, always unplug t by holdng the
socket wth one hand, and pullng the plug wth the other hand.
u
Product should be unplugged durng nstallaton, mantenance,
cleanng and repar procedures.
u
If the power cable s damaged, t must be replaced by the manufacturer,
after sales servce or a smlarly qualfed person (preferably an electrcan)
or someone desgnated by the mporter n order to avod possble rsks.
1.4 Hot surface safety
4 / EN
While washing the laundry at high temperatures,
the loading door glass will get hot. Considering
this fact, during washing operation keep the
children away from the loading door of the
product to prevent them touching it.
Washing Machine / User Manual
2
Important instructions for environment
2.1 Compliance with WEEE Directive
This product complies with EU WEEE Directive (2012/19/EU). This product bears a
classification symbol for waste electrical and electronic equipment (WEEE).
This product has been manufactured with high quality parts and materials which
can be reused and are suitable for recycling. Do not dispose of the waste product
with normal domestic and other wastes at the end of its service life. Take it to the
collection center for the recycling of electrical and electronic equipment. Please
consult your local authorities to learn about these collection centers.
Compliance with RoHS Directive:
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain
harmful and prohibited materials specified in the Directive.
2.2 Package information
Packaging materials of the product are manufactured from recyclable materials in accordance with
our National Environment Regulations. Do not dispose of the packaging materials together with the
domestic or other wastes. Take them to the packaging material collection points designated by the
local authorities.
3
Intended use
• This product has been designed for domestic use. It is not for commercial purposes or it should not
be used out of its intended use.
• The product must only be used for washing and rinsing of laundry that are marked accordingly.
• The manufacturer waives any responsibility arisen from incorrect usage or transportation.
• The service life of your product is 10 years. During this period, original spare parts will be available
to operate the appliance properly.
• This appliance is intended to be used in household and similar applications such as:
– staff kitchen areas in shops, offices and other working environments;
– farm houses;
– by clients in hotels, motels and other residential type environments;
– bed and breakfast type environments;
– areas for communal use in blocks of flats or in launderettes.
Washing Machine / User Manual
5 / EN
4
A
Technical specifications
Supplier name or trademark Beko
Model name
Rated capacity (kg) 7
Maximum spin speed (rpm) 1400
Built-in No
Height (cm) 84
Width (cm) 60
Depth (cm) 55
Single Water inlet / Double Water inlet
• Available
Electrical input (V/Hz) 230 V / 50Hz
Total current (A) 10
Total power (W) 2200
Main model code 9210
WTV77111BW01
7145846400
• / -
C
SUPPLIER’S NAME MODEL IDENTIFIER
A
6 / EN
The model information as stored in the product database can
be reached by entering following website and searching for
(*)
your model identifier (*) found on energy label.
https://eprel.ec.europa.eu/
Washing Machine / User Manual
4.1 Installation
• Apply to the nearest authorised service agent for the installation of your product.
• Preparation of the location and electrical, tap water and waste water installations at the place of
installation is under customer's responsibility.
• Make sure that the water inlet and discharge hoses as well as the power cable are not folded,
pinched or crushed while pushing the product into its place after installation or cleaning
procedures.
• Make sure that the installation and electrical connections of the product are performed by
authorised service. Manufacturer shall not be held liable for damages that may arise from
procedures carried out by unauthorised persons.
• Prior to installation, visually check if the product has any defects on it. If so, do not have it installed.
Damaged products cause risks for your safety.
4.1.1 Approprate nstallaton locaton
• Place the product on a hard and level floor. Do not put it onto a carpet with high pile or other
similar surfaces.
• When the washing machine and dryer are placed on top of each other, their total weight –when
loaded– amounts to 180 kilograms. Place the product on a solid and flat floor that has sufficient
load carrying capacity!
• Do not place the product on the power cable.
• Do not install the product in the environments where the temperature falls below 0 ºC.
• Leaving a gap at the sides of the machine is suggested to reduce vibration and noise
• On a graduated floor, do not place the product next to the edge or on a platform.
• Do not place heat sources such as Hobs, Irons, Ovens, etc. on the washing machine and do not use
them on the product.
4.1.2 Removng packagng renforcement (If the product has)
Tilt the machine backwards to remove the packaging
reinforcement. Remove the packaging reinforcement by pulling the
ribbon. Do not make this operation alone by yourself.
4.1.3 Removng the transportaton locks
1 Loosen all bolts with an appropriate wrench until they turn freely.
2 Remove the transport safety bolts by turning them slightly.
3 Insert the plastic covers in the bag containing the user manual to the openings on the rear
panel.
CAUTION: Remove the transportation safety bolts before operating the washing machine! Otherwise, the
A
C
Washing Machine / User Manual
product will be damaged.
Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again
in the future.
Install the transport safety bolts in reverse order of the disassembly procedure.
Never move the product without the transportation safety bolts properly fixed in place!
7 / EN
4.1.4 Connectng water supply
40 cm
100 cm
It is necessary to have 10 – 80 liters of water flowing from the fully open tap in one minute to have your machine
C
A
run smoothly. Attach a pressure reducing valve if water pressure is higher.
CAUTION: Models with a single water inlet should not be connected to the hot water tap. In such a case the
laundry will get damaged or the product will switch to protection mode and will not operate.
1 Tighten the nuts of the hose by hand. Never use a tool when
tightening the nuts.
2 When hose connection is completed, check whether there is
leak problems at the connection points by opening the taps
fully. If any leaks occur, turn off the tap and remove the nut.
Retighten the nut carefully after checking the seal. In order to
prevent the water leaks and resultant damages, keep the taps
closed when you do not use the product.
4.1.5 Connectng the dran hose to the dran
• Attach the end of the drain hose directly to waste water drain, lavatory or bathtub.
CAUTION: Your drain house will be flooded if the hose comes out of its housing during water discharge.
A
Moreover, there is risk of scalding due to high washing temperatures! In order to prevent such situations and
make sure that the machine performs water intake and discharge processes without any problem, fix the drain
hose securely.
• Connect the drain hose to a minimum height of 40
cm and a maximum height of 100 cm.
• In case the drain hose is elevated after laying it on
the floor level or close to the ground (less than 40 cm
above the ground), water discharge becomes more
difficult and the laundry may come out excessively
wet. Therefore, follow the heights described in the
figure.
• To prevent the waste water to go back into the machine again and to ensure easy drainage, do not
immerse the end of the hose into the waste water or do not insert it into the drain for more than
15 cm. If it is too long, cut it short.
• The end of the hose should not be bent, it should not be stepped on and the hose must not be
pinched between the drain and the machine.
• If the length of the hose is too short, use it by adding an original extension hose. Length of the
hose may not be longer than 3.2 m. To avoid water leak failures, the connection between the
extension hose and the drain hose of the product must be fitted well with an appropriate clamp as
not to come off and leak.
8 / EN
Washing Machine / User Manual
4.1.6 Adjustng the feet
CAUTION: In order to ensure that the product operates more silently and vibration-free, it must stand level
A
1 Loosen the lock nuts on the feet by hand.
2 Adjust the feet until the product stands in a stable and balanced way.
3. Tighten all lock nuts by hand again.
4.1.7 Electrcal connecton
Connect the product to a grounded outlet protected by a 16 A fuse.
be liable for any damages that will arise when the product is used without grounding in
accordance with the local regulations.
• Connection must comply with national regulations.
• The wiring for the electrical outlet circuit must be sufficient to meet the appliance requirements.
Use of a Groud Fault Circuit Interrupter (GFCI) is recommended.
• Power cable plug must be within easy reach after installation.
• If the current value of the fuse or breaker in the house is less than 16 Amps, have a qualified
electrician install a 16 Amp fuse.
• The voltage specified in the "Technical specifications" section must be equal to your mains
voltage.
• Do not make connections via extension cables or multi-plugs.
and balanced on its feet. Balance the machine by adjusting the feet. Otherwise, the product may move from its
place and cause crushing and vibration problems.
CAUTION: Do not use any tools to loosen the lock nuts. Otherwise, they will get damaged.
The Manufacturer shall not
B
4.1.8 Intal use
C
Washing Machine / User Manual
CAUTION: Damaged power cables must be replaced by the Authorised Service Agents.
Use an anti-limescale suitable for the washing machines.
Some water might have remained in the product due to the quality control processes in the production. It is not
harmful for the product.
Before starting to use the product make sure that the preparations
are made which are in line with the “Important Safety and
Environment Instructions” and the instructions in the “Installation”
section.
To prepare the product for washing laundry, perform first operation
in Drum Cleaning programme. If this program is not available in your
machine, apply the method which is described in the section 4.4.2.
9 / EN
4.2 Preparation
4.2.1 Sortng the laundry
* Sort laundry according to type of fabric, color, and degree of soiling and allowable water
temperature.
* Always obey the instructions given on the garment tags.
4.2.2 Preparng laundry for washng
• Laundry items with metal attachments such as, underwired bras, belt buckles or metal buttons
will damage the machine. Remove the metal pieces or wash the clothes by putting them in a
laundry bag or pillow case.
• Take out all substances in the pockets such as coins, pens and paper clips, and turn pockets inside
out and brush. Such objects may damage the product or cause noise problem.
• Put small size clothes such as infant's socks and nylon stockings in a laundry bag or pillow case.
• Place curtains in without compressing them. Remove curtain attachment items.
• Fasten zippers, sew loose buttons and mend rips and tears.
• Wash “machine washable” or “hand washable” labeled products only with an appropriate
programme.
• Do not wash colours and whites together. New, dark coloured cottons release a lot of dye. Wash
them separately.
• Tough stains must be treated properly before washing. If unsure, check with a dry cleaner.
• Only use the dyes / color changers and descaling agents which are appropriate to machine wash.
Always follow the instructions on the package.
• Wash trousers and delicate laundry turned inside out.
• Keep laundry items made of Angora wool in the freezer for a few hours before washing. This will
reduce pilling.
• Laundry that are subjected to materials such as flour, lime dust, milk powder, etc. intensely must
be shaken off before placing into the machine. Such dusts and powders on the laundry may build
up on the inner parts of the machine in time and can cause damage.
4.2.3 Tps for energy and water savng
Following information will help you use the product in an ecological and energy/water-efficient manner.
• Operate the product in the highest load capacity allowed for the programme you have selected,
but do not overload. See, “Programme and consumption table”.
• Observe the temperature instructions on the detergent packaging.
• Wash slightly soiled laundry at low temperatures.
• Use faster programmes for small quantities of lightly soiled laundry.
• Do not use prewash and high temperatures for laundry that is not heavily soiled or stained.
• If you plan to dry your laundry in a dryer, select the highest spin speed recommended during
washing process.
• Do not use more detergent than the recommended on the detergent packaging.
4.2.4 Loadng the laundry
1. Open the laundry cover.
2. Put the laundry items into the machine in a loose manner.
3. Push and close the loading cover until you hear the locking sound. Ensure that no items are caught
in the door. The loading door is locked while a programme is running. The door can only be opened
a while after the programme comes to an end.
4.2.5 Correct load capacty
The maximum load capacity depends on the type of laundry, the degree of soiling and the washing
programme desired.
Machine automatically adjusts the water amount according to the weight of the laundry put inside it.
A
10 / EN
WARNING: Follow the information in the “Programme and consumption table”. When overloaded, machine's
washing performance will drop. Moreover, noise and vibration problems may occur.
Washing Machine / User Manual
4.2.6 Usng detergent and softener
1
3
2
When using detergent, softener, starch, fabric dye, bleacher and decolorant, descaling agents; read the
manufacturer's instructions written on the package and follow the dosages specified. Use measuring cup if
C
Detergent, softener and other cleaning agents
• Add detergent and softener before starting the washing programme.
• While the washing cycle is in progress, do not leave the detergent dispenser open!
• When using a programme without prewash, do not put any detergent into the prewash
compartment (compartment nr. "1").
• In a programme with prewash, do not put liquid detergent into the prewash compartment
(compartment nr. "1").
• Do not select a programme with prewash if you are using a detergent bag or dispensing ball. Place
the detergent bag or the dispensing ball directly among the laundry in the machine.
If you are using liquid detergent, do not forget to place the liquid detergent container into the main
wash compartment (compartment number “2”).
Choosing the detergent type
Detergent type to be used depends on the washing programme, fabric type and color.
• Use different detergents for coloured and white laundry.
• Wash your delicate clothes only with special detergents (liquid detergent, wool shampoo, etc.)
intended solely for delicate clothes and at suggested programmes.
• When washing dark coloured clothes and quilts, it is recommended to use liquid detergent.
• Wash woolens at suggested programme with special detergent made specifically for woolens
•Please review the program descriptions part for suggested program for different textiles.
• All recommendations about detergents are valid for selectable temperature range of programmes.
A
Adjusting detergent amount
The amount of washing detergent to be used depends on the amount of laundry, the degree of
soiling and water hardness.
• Do not use amounts exceeding the dosage quantities recommended on the detergent package
to avoid problems of excessive foam, poor rinsing, financial savings and finally, environmental
protection.
• Use less detergent for smaller loads, lightly soiled clothes or when using short duration
programmes especially in soft water areas.
Using softeners
Pour the softener into the softener compartment of the detergent drawer.
• Do not exceed the (>max<) level sign on the softener compartment.
• If the softener has lost its fluidity, dilute it with water before putting it in the detergent drawer.
available.
The detergent drawer is composed of three
compartments:
– (1) for prewash
– (2) for main wash
– (3) for softener
– ( ) in addition, there is a siphon piece in the
softener compartment.
CAUTION: Use only detergents manufactured specifically for washing machines.
CAUTION: Do not use soap powder.
Washing Machine / User Manual
11 / EN
Using liquid detergents
2
If the product contains a liquid detergent cup:
• Put the liquid detergent container into the
compartment no “2”.
• If the liquid detergent lost its fluidity, dilute
it with water before putting it into the
detergent container.
If the product is equipped with a liquid detergent part:
• When you want to use liquid detergent,
pull the apparatus towards yourself. The
part that falls down will serve as a barrier
for the liquid detergent.
• If required, clean the apparatus with water
when it is in place or by removing it.
• If you will use powder detergent, the
apparatus must be secured at top position.
If the product does not contain a liquid detergent cup:
• Do not use liquid detergent for the prewash in a programme with prewash.
• Liquid detergent stains your clothes when used with Delayed Start function. If you are going to
use the Delayed Start function, do not use liquid detergent.
Using gel and tablet detergent
• If the gel detergent thickness is fluidal and your machine does not contain a special liquid
detergent cup, put the gel detergent into the main wash detergent compartment during first
water intake. If your machine contains a liquid detergent cup, fill the detergent into this cup before
starting the programme.
• If the gel detergent thickness is not fluidal or in the shape of capsule liquid tablet, put it directly
into the drum before washing.
• Put tablet detergents into the main wash compartment (compartment nr. "2") or directly into the
drum before washing.
Using starch
• Put the liquid soda, powder soda or the fabric dye into the softener compartment.
Do not use softener and starch together in a washing cycle.
Wipe the inside of the machine with a damp and clean cloth after using starch.
Using limescale remover
• When required, use limescale removers manufactured specifically for washing machines only.
Using bleaches
• Add the bleach at the beginning of the washing cycle by selecting a prewash program. Do not put
detergent in the prewash compartment. As an alternative application, select a programme with
extra rinse and add the bleaching agent while the machine is taking water from the detergent
compartment during first rinsing step.
• Do not use bleaching agent and detergent by mixing them.
• Use just a little amount (approx. 50 ml) of bleaching agent and rinse the clothes very well as it causes
skin irritation. Do not pour the bleach onto the laundry and do not use it with the colored items.
• When using oxygen-based decolorant, select a program which washes the laundry at a low
temperature.
• Oxygen-based decolorant can be used with the detergent; however, if it is not at the same
consistence, first put detergent in the compartment number “2” in the detergent dispenser and
wait for the machine to flush the detergent when taking in water. While the machine continues
taking in water, add decolorant in the same compartment.
12 / EN
Washing Machine / User Manual
4.2.7 Tps for effcent washng
Light Colours and
Whites
(Recommended
temperature range based
on soiling level: 40-90 oC)
Clothes
Colours
(Recommended
temperature range based
on soiling level: cold -40
o
C)
Black/Dark
Colours
(Recommended
temperature range
based on soiling
level: cold -40 oC)
Delicates/
Woolens/Silks
(Recommended
temperature range
based on soiling
level: cold -30 oC)
Heavily
Soiled
(difficult stains
such as grass,
coffee, fruits
and blood.)
Normally
Soiled
Soiling Level
(For example,
stains caused
by body on
collars and
cuffs)
Lightly
Soiled
(No visible
stains exist.)
It may be necessary to pretreat the stains or perform
prewash. Powder and liquid
detergents recommended
for whites can be used at
dosages recommended
for heavily soiled clothes.
It is recommended to use
powder detergents to
clean clay and soil stains
and the stains that are
sensitive to bleaches.
Powder and liquid
detergents recommended
for whites can be used at
dosages recommended
for normally soiled
clothes.
Powder and liquid
detergents recommended
for whites can be used at
dosages recommended
for lightly soiled clothes.
Powder and liquid
detergents recommended
for colors can be used at
dosages recommended
for heavily soiled clothes.
It is recommended to use
powder detergents to
clean clay and soil stains
and the stains that are
sensitive to bleaches.
Use detergents without
bleach.
Powder and liquid
detergents recommended
for colors can be used at
dosages recommended
for normally soiled
clothes. Detergents which
do not contain bleach
should be used.
Powder and liquid
detergents recommended
for colors can be used at
dosages recommended
for lightly soiled clothes.
Detergents which do not
contain bleach should
be used.
Liquid detergents
suitable for
colors and dark
colors can be
used at dosages
recommended
for heavily soiled
clothes.
Liquid detergents
suitable for
colors and dark
colors can be
used at dosages
recommended for
normally soiled
clothes.
Liquid detergents
suitable for
colors and dark
colors can be
used at dosages
recommended
for lightly soiled
clothes.
Prefer liquid
detergents
produced for
delicate clothes.
Woolen and silk
clothes must
be washed with
special woolen
detergents.
Prefer liquid
detergents
produced for
delicate clothes.
Woolen and silk
clothes must be
washed with special
woolen detergents.
Prefer liquid
detergents
produced for
delicate clothes.
Woolen and silk
clothes must be
washed with special
woolen detergents.
Washing Machine / User Manual
13 / EN
4.3 Operating the product
Symbols Table
4.3.1 Control panel
1
2 3 4 6
5
789
1 - Programme Selection knob (Uppermost
position On / Off)
2 - Spin Speed Indicator LEDs
3 - Child Lock Enabled LED
4 - Door Lock Enabled LED
Extra
Anti
Prewash Fast Fast+ Extra
Rinse
Spin+Drain
Wash
Ok
(End)
Rinse
Drain
Temperature Door
AntiCrease+ Iron
Cancel
Water
Spin No
Drying
Crease
Spin
Extra
Dry
Pet Hair
Removal
Tap
Water
(Cold)
Cupboard
Steam
No
Water
Dry
5 - Delayed Start Indicator LEDs
6 - Programme Follow-up LEDs
7 - Start / Pause Button
8 - Delayed Start Setting Button
9 - Spin Speed Adjustment button
Soaking
Night
Modu
Time
Delay
Lock
Timed
Dry
Drying
4.3.2 Preparng the machne
1.Make sure that the hoses are connected tightly.
2.Plug in your machine.
3.Turn the tap on completely.
4.Place the laundry in the machine.
5.Add detergent and fabric softener.
4.3.3 Programme selecton and tps for effcent washng
1.Select the programme suitable for the type, quantity and soiling degree of the laundry in
accordance with the "Programme and consumption table" and the temperature table below.
2.Select the desired programme with the Programme Selection knob.
Child
Lock
Rinse
Hold
On/Off Start /
Steeping
Pause
AutoDose
Detergent
Selection
Soil Level Add
Liquid
Garment
Softener
Selection
Downloaded
Program
14 / EN
Washing Machine / User Manual
4.3.4 Programme and consumpton table
EN 2
Programme
Max. Load (kg)
Programme Duration (~min)
7 195 98 2,45
90
7 207 52 0,990
60**
Katoen
Katoen 60º met Voorwas 60
Eco 40-60
Synthetisch
Xpress 30
Wol 40
Donsjas 40
Hemden 40
Reiniging trommel 90
60** 3,5 161 43,5 0,600
40 7 195 96 1,10
7 195 96 0,58
20
7 215 106 1,95
7 207 52 0,980
40***
3,5 161 43 0,570
40**,***
2 161 36 0,383
40***
3 130 69 0,80 1200
40
3 130 67 0,26 1200
20
7 28 65 0,15
1,5 65 53 0,47 1200
1,5 105 90 0,85 1000
3 80 45 0,60 800
- 160 70 2,60 600
Water Consumption (l)
Energy Consumption (kWh)
Max. Speed
1400
1400
1400
1400
1400
1400
1400
1400
1400
1400
** : Eco 40-60 ( ) and Cottons 60 °C ( ) are the test programs in accordance with EN 60456:2016 and energy label with
Commission Delegated Regulation (EU) 1061/2010
***: Eco 40-60 is the test program in accordance with EN 60456:2016/prA:2019 and energy label with Commission Delegated
Regulation (EU) 2019/2014
- : See the programme description for maximum load.
Water and power consumption may vary subject to the changes in water pressure, water hardness and temperature,
C
Washing Machine / User Manual
ambient temperature, type and amount of laundry, spin speed, and changes in electric voltage.
Depending on the amount of laundry you have loaded into your machine, there may be a difference of 1-1.5 hours
between the duration shown in the Programme and consumption table and the actual washing duration. Duration will
be automatically updated soon after the washing starts.
Always select the lowest appropriate temperature. The most efficient programmes in terms of energy consumption are
generally those that perform at lower temperatures and longer duration.
Noise and remaining moisture content are influenced by the spinning speed: the higher the spinning speed in the
spinning phase, the higher the noise and the lower the remaining moisture content.
15 / EN
Consumption Values (EN)
Temperature
Eco 40-60
Katoen
Katoen 60º met Voorwas
Synthetisch
Xpress
Selection (°C)
40 1400 7 03:27
40 1400 3,5 02:41
40 1400 2 02:41
20 1400 7 03:15
60 1400 7 03:35
40 1200
30 1400 7 00:28
Spin Speed (rpm)
Capacity (kg)
3
Program Duration
02:10
(hh:mm)
Energy
Consumption(kWh/
cycle)
Water
Consumption(L/
cycle)
0,980 52,0 41 53
0,570 43,0 34 53
0,383 36,0 27 53
0,580 96,0 20 53
1,950 106,0 60 53
0,800 69,0 40 40
0,150 65,0 23 62
Laundry
Temperature (°C)
4.3.5 Man programmes
Depending on the type of fabric, use the following main programmes.
• Katoen (Cottons) 20-40-90
Use this programme for your cotton laundry (sheets, bedlinen, towels, bathrobes, underwear etc.).
Your laundry will be washed with vigorous washing action for a longer washing cycle.
• Synthetisch (Synthetics)
Use to wash your synthetc clothes (shrts, blouses, synthetc/cotton blends, etc.). Your laundry
wll be washed wth a gentle acton for a shorter washng cycle when compared to the Cottons
programme. For curtans and tulle, t s recommended to use Synthetcs 20˚C or 40˚C programme.
• Wol (Woollens / Hand Wash)
Use to wash your woolen/delicate laundry. Your laundry will be washed with a very gentle washing
action in order not to damage the clothes.
Remaining
Moisture Content
(%)
4.3.6 Addtonal programmes
For special cases, additional programmes are available in the machine.
Additional programmes may differ according to the model of the machine.
C
• Eco 40-60
The Eco 40-60 programme is able to clean normally soiled cotton laundry declared to be washable at 40
°C or 60 °C, together in the same cycle, and that this programme is used to assess the compliance with
the EU ecodesign legislation.
Although it washes longer than all other programmes, it provides high energy and water savings. Actual
water temperature may be different from the stated wash temperature. When you load the machine
with less laundry (e.g. ½ capacity or less), periods in programme stages may automatically get shorter. In
this case, energy and water consumption will decrease more.
• Katoen (Cottons) 60
Use to wash your normally soiled, durable cotton and linen laundry. Although it washes longer than
all other programmes, it provides high energy and water savings. Actual water temperature may be
different from the stated wash temperature. When you load the machine with less laundry (e.g. ½
capacity or less), periods in programme stages may automatically get shorter. In this case, energy
and water consumption will decrease more, providing a more economic wash.
• Katoen 60º met Voorwas (Cottons 60° with Prewash)
Use this programme only for heavily soiled cotton clothes. Add detergent into the prewash
compartment.
16 / EN
Washing Machine / User Manual
• Xpress
Use this programme to wash your lightly soiled cotton clothes in a short time.
• Hemden (Shirts)
This programme is used to wash the shirts made from cotton, synthetic and synthetic blended
fabrics altogether. It reduces wrinkles. Pre-treatment algorithm is executed.
• Apply the pre-treatment chemical on your garments directly or add it together with detergent
when the machine starts to take water from the main washing compartment. Thus the machine will
wash them in a short period of time and expected lifespan of your shirts will extend.
• Donsjas (Down Wear)
Use this programme to wash your coats, vest, jackets etc. containing feathers with a "machinewashable" label on them. Thanks to special spinning profiles, it is ensured that the water reaches the
air gaps amongst the feathers.
• Reiniging trommel (Drum Clean)
Use regularly (once in every 1-2 months) to clean the drum and provide the required hygiene.
Operate the programme while the machine is completely empty. To obtain better results, put
powder lime-scale remover for washing machines into the detergent compartment no. “2”. When the
programme is over, leave the loading door ajar so that the inside of the machine gets dry.
This is not a washing programme. It is a maintenance programme.
C
Do not run the programme when there is something in the machine. If you try to do so, the machine detects that
there is load inside and aborts the programme.
4.3.7 Specal programmes
For specific applications, select any of the following programmes.
• Spoelen (Rinse)
Use when you want to rinse or starch separately.
• Centrifugeren + Pompen (Spin+Drain)
You can use this function to remove the water on the garment of drain the water in the machine.
Before selecting this programme, select the desired spin speed and press Start / Pause button. First,
the machine will drain the water inside of it. Then, it will spin the laundry with the set spin speed and
drain the water coming out of them.
If you wish to drain only the water without spinning your laundry, select the Pump+Spin programme
and then select the No Spin function with the help of Spin Speed Adjustment button. Press Start /
Pause button.
C
Use a lower spin speed for delicate laundries.
4.3.8 Speed selecton
Whenever a new programme is selected, the recommended spin speed of the selected programme is
displayed on the spin speed indicator.
To decrease the spin speed, press the Spin Speed Adjustment button. Spin speed decreases
gradually. Then, depending on the model of the product, "Rinse Hold" and "No Spin" options appear
on the display. When "No Spin" is selected, the rinse level indicator lights will not turn on.
Rinse hold
If you are not going to unload your clothes immediately after the programme completes, you can
use rinse hold function to keep your laundry in the final rinsing water in order to prevent them from
getting wrinkled when there is no water in the machine. Press Start / Pause button after this process
if you want to drain the water without spinning your laundry. Programme will resume and complete
after draining the water.
If you want to spin the laundry held in water, adjust the Spin Speed and press Start / Pause button.
The programme will resume. Water is drained, laundry is spun and the programme is completed.
If the programme has not reached the spinning step, you can change the speed without switching the machine
C
Washing Machine / User Manual
to Pause mode.
17 / EN
4.3.9 Delayed Start
With the Delayed Start function the startup of the programme may be delayed up to 3, 6 or 9 hours.
C
Do not use liquid detergents when you set Delayed Start! There is the risk of staining of the clothes.
1. Open the loading door, place the laundry and put detergent, etc.
2. Select a washing programme and spin speed.
3. Set the desired time by pressing the Delayed Start button. When the button is pressed once, 3 hours
delayed start is selected. When the same button is pressed again, 6 hours delay is selected, and when
it is pressed for the third time, 9 hours delayed start is selected. If you press the Delayed Start button
once again, Delayed Start function will be canceled.
4. Press Start / Pause button. Previous delayed start time light turns off and next delayed start time
light turns on after every 3 hours.
5. At the end of the countdown, all delayed start lights will turn off and the selected programme will
start.
You can switch the machine to pause mode and add laundry during the delayed start period.
C
Changing the delayed start period
If you want to change the time during countdown, you will need to cancel the programme and set
the delay time again.
Canceling the Delayed Start function
If you want to cancel the delayed start countdown and start the programme immediately:
1. Turn the Programme Selection knob to any programme. Thus, Delayed Start function will be
canceled. The End/Cancel light flashes continuously.
2. Then, select the programme you want to run again.
3. Press Start / Pause button to start the programme.
4.3.10 Startng the programme
1. Press Start / Pause button to start the programme.
2. Programme follow-up light showing the startup of the programme will turn on.
4.3.11 Chld Lock
Use Child Lock function to prevent children from tampering with the machine. Thus you can avoid
any changes in a running programme.
If the Programme Selection knob is rotated when the child lock is active, "Child Lock Enabled LED" will flash 3
C
To activate the Child Lock:
Press and hold Speed and Delayed Start buttons for 3 seconds. While you are holding for 3 seconds,
the "Child Lock Enabled LED" will flash. You can release the buttons when the LEDs become
permanently on.
times. The Child Lock does not allow any change in the programmes or the selected speed.
Even if another programme is selected with the Programme Selection knob while the Child Lock is active,
previously selected programme will continue running.
When the Child Lock is active and the machine is running, you can switch the machine to Pause mode without
deactivating the Child Lock by turning the Programme Selection knob to On / Off position. When you turn the
Programme Selection knob afterwards, the programme will resume.
18 / EN
Washing Machine / User Manual
Loading...