This section provides the safety
instructions necessary to prevent
the risk of injury and material
damage. Failure to observe these
instructions will invalidate all
types of product warranty.
1.1. General safety
• This product should not be
used by persons with physical,
sensory and mental disabilities,
without sufficient knowledge
and experience or by children.
The device can only be
used by such persons under
supervision and instruction of
a person responsible for their
safety. Children should not be
allowed to play with this device.
• In case of malfunction, unplug
the device.
• After unplugging, wait at least
5 minutes before plugging in
again.
• Unplug the product when not in
use.
• Do not touch the plug with wet
hands! Do not pull the cable to
plug off, always hold the plug.
• Wipe the power plug’s tip with
a dry cloth before plugging in.
• Do not plug in the refrigerator if
the socket is loose.
• Unplug the product during
installation, maintenance,
cleaning and repair.
Refrigerator / User Manual
• If the product will not be used
for a while, unplug the product
and remove any food inside.
• Do not use the product when
the compartment with circuit
cards located on the upper
back part of the product
(electrical card box cover) (1) is
open.
1
1
• Do not use steam or steamed
cleaning materials for cleaning
the refrigerator and melting the
ice inside. Steam may contact
the electrified areas and cause
short circuit or electric shock!
• Do not wash the product by
spraying or pouring water on it!
Danger of electric shock!
• In case of malfunction, do not
use the product, as it may
cause electric shock. Contact
3 / 33 EN
Safety and environment instructions
the authorized service before
doing anything.
• Plug the product into an
earthed socket. Earthing
must be done by a qualified
electrician.
• If the product has LED type
lighting, contact the authorized
service for replacing or in case
of any problem.
• Do not touch frozen food with
wet hands! It may adhere to
your hands!
• Do not place liquids in bottles
and cans into the freezer
compartment. They may burst
out!
• Place liquids in upright position
after tightly closing the lid.
• Do not spray flammable
substances near the product,
as it may burn or explode.
• Do not keep flammable
materials and products with
flammable gas (sprays, etc.) in
the refrigerator.
• Do not place containers
holding liquids on top of the
product. Splashing water on
an electrified part may cause
electric shock and risk of fire.
• Exposing the product to rain,
snow, sunlight and wind will
cause electrical danger. When
relocating the product, do not
pull by holding the door handle.
The handle may come off.
• Take care to avoid trapping any
part of your hands or body in
any of the moving parts inside
the product.
• Do not step or lean on the door,
drawers and similar parts of
the refrigerator. This will cause
the product to fall down and
cause damage to the parts.
• Take care not to trap the power
cable.
1.1.1 HC warning
If the product comprises a cooling
system using R600a gas, take
care to avoid damaging the
cooling system and its pipe while
using and moving the product.
This gas is flammable. If the
cooling system is damaged, keep
the product away from sources
of fire and ventilate the room
immediately.
4 / 33 EN
Refrigerator / User Manual
Safety and environment instructions
The label on the inner
left side indicates the
C
type of gas used in the
product.
1.1.2 For models with
water dispenser
• Pressure for cold water inlet
shall be maximum 90 psi (6.2
bar). If your water pressure
exceeds 80 psi (5.5 bar), use a
pressure limiting valve in your
mains system. If you do not
know how to check your water
pressure, ask for the help of a
professional plumber.
• If there is risk of water hammer
effect in your installation,
always use a water hammer
prevention equipment in
your installation. Consult
Professional plumbers if you
are not sure that there is no
water hammer effect in your
installation.
• Do not install on the hot water
inlet. Take precautions against
of the risk of freezing of the
hoses. Water temperature
operating interval shall be 33°F
(0.6°C) minimum and 100°F
(38°C) maximum.
• Use drinking water only.
1.2. Intended use
• This product is designed for
home use. It is not intended for
commercial use.
• The product should be used to
store food and beverages only.
• Do not keep sensitive
products requiring controlled
temperatures (vaccines,
heat sensitive medication,
medical supplies, etc.) in the
refrigerator.
• The manufacturer assumes no
responsibility for any damage
due to misuse or mishandling.
• The product’s bench life is
10 years. The spare parts
necessary for the product to
function will be available for
this period.
1.3. Child safety
• Keep packaging materials out
of children’s reach.
• Do not allow the children to
play with the product.
• If the product’s door comprises
a lock, keep the key out of
children’s reach.
1.4. Compliance with WEEE Directive
and Disposing of the Waste Product
This product complies with EU WEEE
Directive (2012/19/EU). This product bears a
classification symbol for waste electrical and
electronic equipment (WEEE).
Refrigerator / User Manual
5 / 33 EN
Safety and environment instructions
This product has been manufactured
with high quality parts and materials
which can be reused and are suitable
for recycling. Do not dispose of the
waste product with normal domestic
and other wastes at the end of its
service life. Take it to the collection
center for the recycling of electrical and
electronic equipment. Please consult your local
authorities to learn about these collection
centers.
1.5. Compliance with RoHS Directive
• This product complies with EU WEEE Directive
(2011/65/EU). It does not contain harmful and
prohibited materials specified in the Directive.
1.6. Package information
• Packaging materials of the product are
manufactured from recyclable materials in
accordance with our National Environment
Regulations. Do not dispose of the packaging
materials together with the domestic or other
wastes. Take them to the packaging material
collection points designated by the local
authorities.
6 / 33 EN
Refrigerator / User Manual
*1
*3
*2
*5
*6
7
*8
9
4
A
B
2 Refrigerator
A- Cooler compartment
B- Freezer compartment
1. Butter-cheese shelf
2. Cooler compartment shelves
3. Shelter wire
*Optional: Figures in this user guide are schematic and may not exactly match your product. If your
product does not comprise the relevant parts, the information pertains to other models.
C
4. Frozen food storing compartments
5. Vegetable bins
6. Breakfast compartment
7. Odour filter
8. Adjustable glass shelves
9. Fan
Refrigerator / User Manual
7 / 33 EN
3 Installation
3.1. Right place for installation
Contact the Authorized Service for the product's
installation. To ready the product for installation,
see the information in the user guide and make
sure the electric and water utilities are as required.
If not, call an electrician and plumber to arrange
the utilities as necessary.
WARNING: The manufacturer assumes
no responsibility for any damage caused
B
B
A
•Placetheproductonaflatsurfacetoavoid
vibration.
•Placetheproductatleast30cmawayfromthe
heater, stove and similar sources of heat and at
least 5 cm away from electric ovens.
function efficiently. If the product will be placed
in an alcove, remember to leave at least 5 cm
distance between the product and the ceiling
and the walls.
must be unplugged during installation.
Failure to do so may result in death or
serious injuries!
WARNING: If the door span is too narrow
for the product to pass, remove the door
and turn the product sideways; if this does
not work, contact the authorized service.
3.2. Attaching the plastic wedges
Use the plastic wedges provided with the product
to provide sufficient space for air circulation
between the product and the wall.
1.
To attach the wedges, remove the screws on the
product and use the screws provided with the wedges.
2.
Attach 2 plastic wedges on the ventilation cover as
shown in the figure.
8 / 33 EN
Refrigerator / User Manual
Installation
3.3. Adjusting the stands
If the product is not in balanced position, adjust the
front adjustable stands by rotating right or left.
3.4. Power connection
WARNING: Do not use extension or
A
B
C
• Our firm will not assume responsibility for any
• The power cable plug must be easily
• Connect the refrigerator to an earthed socket
• Do not use multi-group plug with or without
multi sockets in power connection.
WARNING: Damaged power cable
must be replaced by Authorized
Service.
When placing two coolers in adjacent
position, leave at least 4 cm distance
between the two units.
damages due to usage without earthing and
power connection in compliance with national
regulations.
accessible after installation.
with 220-240V/50 Hz voltage. The socket must
comprise a 10-16A fuse.
extension cable between the wall socket and
the refrigerator.
3.5. Water connection
(Optional)
WARNING: Unplug the product and
the water pump (if available) during
A
The product’s water mains, filter and carboy
connections must be rendered by authorized
service.
The product can be connected to a carboy or
directly to the water mains, depending on the
model. To establish the connection, the water hose
must first be connected to the product.
Check to see the following parts are supplied with
your product’s model:
1
3
1. Connector (1 piece): Used to attach the water
2. Hose clip (3 pieces): Used to fix the water
3. Water hose (1 piece, 5 meter diameter 1/4
4. Faucet adapter (1 piece): Comprises a porous
5. Water filter (1 piece *Optional): Used to
connection.
2
4
hose to the rear of the product.
hose on the wall.
inches): Used for the water connection.
filter, used for connection to the cold water
mains.
connect the mains water to the product. Water
filter is not required if carboy connection is
available.
*5
Refrigerator / User Manual
9 / 33 EN
Installation
3.6. Connecting water
hose to the product
To connect the water hose to the product,
follow the instructions below.
1. Remove the connector on the hose nozzle
adaptor in the back of the product and run the
hose through the connector.
3.7. Connecting to water mains
(Optional)
To use the product by connecting to the cold water
mains, a standard 1/2” valve connector must be
installed to the cold water mains in your home. If
the connector is not available or if you are unsure,
consult a qualified plumber.
1. Detach the connector (1) from the faucet
adaptor (2).
2. Push the water hose down tightly and connect
to the hose nozzle adaptor.
3. Tighten the connector manually to fix on the
hose nozzle adaptor. You may also tighten the
connector using a pipe wrench or pliers.
23
2. Connect the faucet adaptor to the water mains
valve.
3. Attach the connector around the water hose.
1
10 / 33 EN
Refrigerator / User Manual
Installation
4. Attach the connector into the faucet adaptor
and tighten by hand / tool.
2. Connect the other end of the water hose to
the water pump by pushing the hose into the
pump’s hose inlet.
5. To avoid damaging, shifting or accidentally
disconnecting the hose, use the clips provided
to fix the water hose appropriately.
WARNING:After turning the faucet on,
make sure there is no water leak on
A
3.8. For products using water carboy
(Optional)
To use a carboy for the product’s water
connection, the water pump recommended by the
authorized service must be used.
1. Connect one end of the water hose provided
either end of the water hose. In case of
leakage, turn the valve off and tighten all
connections using a pipe wrench or pliers.
with the pump to the product (see 3. 6) and
follow the instructions below.
3. Place and fasten the pump hose inside the
carboy.
4. Once the connection is established, plug in
and start the water pump.
Please wait 2-3 minutes after starting the
C
C
C
3.9 Water filter
(Optional)
The product may have internal or external filter,
depending on the model. To attach the water filter,
follow the instructions below.
pump to achieve the desired efficiency.
See also the pump’s user guide for water
connection.
When using carboy, water filter is not
required.
Refrigerator / User Manual
11 / 33 EN
Installation
3.9.1. Fixing external filter
on the wall (Optional)
WARNING: Do not fix the filter on the
A
Check to see the following parts are supplied with
your product’s model:
1. Connector (1 piece): Used to attach the water
2. Faucet adapter (1 piece): Used for connection
3. Porous filter (1 piece)
4. Hose clip (3 pieces): Used to fix the water
5. Filter connecting apparatus (2 pieces): Used to
6. Water filter (1 piece): Used to connect the
product.
5
4
6
1
hose to the rear of the product.
to the cold water mains.
hose on the wall.
fix the filter on the wall.
mains water to the product. Water filter is not
required if carboy connection is available.
3
2
2. Determine the location to fix the external filter.
Fix the filter’s connecting apparatus (5) on the
wall.
3. Attach the filter in upright position on the filter
connecting apparatus, as indicated on the
label. ( 6 ).
1. Connect the faucet adaptor to the water mains
valve.
12 / 33 EN
4. Attach the water hose extending from the top
of the filter to the product’s water connection
adaptor (see. 3 6).
Refrigerator / User Manual
Installation
After the connection is established, it should look
like the figure below.
Water line:
3.9.2. Internal filter
The internal filter provided with the product is
not installed upon delivery; please follow the
instructions below to install the filter.
1. “Ice Off ” indicator must be active while
installing the filter. Switch the ON-OFF
indicator using the “Ice” button on the screen.
2. Remove the vegetable bin (a) to access the
water filter.
Carboy line:
Refrigerator / User Manual
aa
13 / 33 EN
Installation
3. Remove the water filter by-pass cover by
pulling.
A few drops of water may flow out after
C
4. Place the water filter cover into the
removing the cover; this is normal.
mechanism and push to lock in place.
5. Push the “Ice” button on the screen again to
cancel the “Ice Off ” mode.
The water filter will clear certain foreign
particles in the water. It will not clear the
C
C
microorganisms in the water.
The filter replacement period of your
product is 6 months.
14 / 33 EN
Refrigerator / User Manual
4 Preparation
4.1. What to do for energy saving
Connecting the product to electronic
energy-saving systems is harmful, as it
A
• Do not keep the refrigerator doors open for
• Do not place hot food or beverages into the
• Do not overfill the refrigerator; blocking the
• To be able store maximum food in the freezer
• Depending on the product’s features;
• Make sure the foods are not in contact with
may damage the product.
long periods.
refrigerator.
internal air flow will reduce cooling capacity.
compartment of your refrigerator, the upper
drawers have to be removed and placed on
top of wire rack. The net volume and energy
consumption values specified in the energy
label of the refrigerator was tested after
removing the freezer compartment’s upper
shelf and the ice container which can easily
be removed manually. Using the lower drawer
while loading is highly recommended.
defrosting frozen foods in the cooler
compartment will ensure energy saving and
preserve food quality.
the cooler compartment temperature sensor
described below.
• Food must be stored in drawers inside the
cooler compartment in order to provide energy
saving and preserve the food in a better
ambient.
• Prevent direct contact between the
temperature sensor in the freezer compartment
and the food packages. Energy consumption
may increase in case of a contact with the
sensor.
4.2. First use
Before using your refrigerator, make sure the
necessary preparations are made in line with
the instructions in “Safety and environment
instructions” and “Installation” sections.
• Keep the product running with no food inside
for 6 hours and do not open the door, unless
absolutely necessary.
A sound will be heard when the
compressor is engaged. It is normal to
C
C
C
hear sound even when the compressor is
inactive, due to the compressed liquids and
gasses in the cooling system.
It is normal for the front edges of the
refrigerator to be warm. These areas are
designed to warm up in order to prevent
condensation.
In some models, indicator panel is dimmed
automatically 5 minutes after the door is
closed. It will be activated again when the
door is opened or any key is pressed.
Refrigerator / User Manual
15 / 33 EN
5 Using the product
5.1. Indicator panel
Indicator panels may vary depending on the model of your product.
Audio and visual functions of the indicator panel will assist in using the refrigerator.
8
9
1. Cooler compartment indicator
2. Error status indicator
3. Temperature indicator
4. Vacation function button
5. Temperature adjustment button
6. Compartment selection button
7. Freezer compartment indicator
8. Economy mode indicator
9. Vacation function indicator
*optional
1
7
2
6
3
45
C
*Optional: The figures in this user guide are intended as drafts and may not perfectly match your
product. If your product does not comprise the relevant parts, the information pertains to other models.
16 / 33 EN
Refrigerator / User Manual
Using the product
1. Cooler compartment indicator
The cooler compartment light will turn on when
adjusting the cooler compartment temperature.
2. Error status indicator
This sensor will activate if the refrigerator is not
cooling adequately or in case of sensor fault. When
this indicator is active, the freezer compartment
temperature indicator will display "E" and the
cooler compartment temperature indicator will
display "1, 2, 3..." etc. numbers. The numbers on
the indicator serve to inform the service personnel
about the fault. ( )
3. Temperature indicator
Indicates the temperature of the freezer and cooler
compartments.
4. Vacation function button
To activate this function, press and hold the
Vacation button for 3 seconds. When the Vacation
function is active, the cooler compartment
temperature indicator displays the inscription
"- -" and no cooling process will be active in
the cooling compartment. This function is not
suitable to keep food in the cooler compartment.
Other compartments will remain cooled with the
respective temperature set for each compartment.
Push the Vacation button () again to cancel
this function.
5. Temperature adjustment button
Respective compartment's temperature varies in
-24°C... -18°C and 8°C...1°C ranges. ()
6. Compartment selection button
Use the refrigerator compartment selection
button to toggle between the cooler and freezer
compartments. ( )
7. Freezer compartment indicator
The freezer compartment light will turn on when
adjusting the freezer compartment temperature.
8. Economy mode indicator
Indicates the refrigerator is running on energysaving mode. This indicator will be active when the
temperature in the freezer compartment is set to
-18°C. ( )
9. Vacation function indicator
Indicates the vacation function is active. ()
Refrigerator / User Manual
17 / 33 EN
Using the product
Indicator panel
This touch-control indicator panel allows you to set the temperature without opening the door of your refrigerator. Just touch the relevant button with your finger to set the temperature.
2
1
3
11
1- Economic use
2- High temperature / fault alert
3- Energy saving function (display off)
4- Rapid cooling
5- Vacation function
6- Cooler compartment temperature setting
7- Energy saving (display off) / Alarm off warning
8- Keypad lock
9- Eco-fuzzy
10- Freezer compartment temperature setting
11- Rapid freezing
4
7.1
7.2
8910
56
C
*Optional: The figures in this user guide are intended as drafts and may not perfectly match your
product. If your product does not comprise the relevant parts, the information pertains to other models.
18 / 33 EN
Refrigerator / User Manual
Using the product
1. Economic use
This sign will light up when the freezer compartment is set to -18°C', the most economical
setting. ( ) Economic use indicator will turn off
when rapid cooling or rapid freezing function is
selected.
2. High temperature / fault alert
This indicator () will light up in case of temperature faults or fault alerts. If you see this indicator
is lit up, please see the "recommended solutions
for problems" section in this guide.
This indicator illuminates during power failure, high
temperature failures and error warnings. During
sustained power failures, the highest temperature
that the freezer compartment reaches will flash on
the digital display. After checking the food located
in the freezer compartment press the alarm off
button to clear the warning.
Please refer to “remedies advised for
troubleshooting” section on your manual if you
observe that this indicator is illuminated.
3. Energy saving function (display off)
If the product doors are kept closed for a long time
energy saving function is automatically activated
and energy saving symbol is illuminated. When
energy saving function is activated, all symbols
on the display other than energy saving symbol
will turn off. When the Energy Saving function is
activated, if any button is pressed or the door is
opened, energy saving function will be canceled
and the symbols on display will return to normal.
Energy saving function is activated during delivery
from factory and cannot be canceled.
4. Rapid cooling
When the rapid cooling function is turned on, the rapid
cool indicator will light up () and the cooler compartment temperature indicator will display the value 1.
Push the Rapid cool button again to cancel this function. The Rapid cool indicator will turn off and return
to normal setting. The rapid cooling function will be
automatically cancelled after 1 hour, unless cancelled
by the user. Too cool a large amount of fresh food,
Refrigerator / User Manual
19 / 33 EN
press the rapid cool button before placing the food in
the cooler compartment.
5. Vacation function
To activate the Vacation function, press the
button for () 3 seconds; this will activate the
vacation mode indicator (). When the Vacation
function is active, the cooler compartment
temperature indicator displays the inscription
"- -" and no cooling process will be active in
the cooling compartment. This function is not
suitable to keep food in the cooler compartment.
Other compartments will remain cooled with the
respective temperature set for each compartment.
Push the vacation function button again to
cancel this function
6. Cooler compartment temperature setting
After pressing the button, the cooler compartment
temperature can be set to 8,7,6,5,4,3,2 and 1
respectively. ()
7.1. Energy saving (display off)
Pressing this button () will light up the energy
saving sign () and the Energy-saving function
will activate. Activating the energy-saving function
will turn off all other signs on the display. When
the energy-saving function is active, pressing any
button or opening the door will deactivate the
energy-saving function and the display signals will
return to normal. Pressing this button () again
will turn off the energy-saving sign and deactivate
the energy-saving function.
7.2.Alarm off warning:
In case of power failure/high temperature alarm,
after checking the food located in the freezer
compartment press the alarm off button to clear
the warning.
8. Keypad lock
Press the keypad lock button () simultaneously
for 3 seconds. The keypad lock sign
( ) will light up and the keypad lock will be
activated. The buttons will be inactive when the
Keypad lock is activated. Press the Keypad lock
button again simultaneously for 3 seconds. The
keypad lock sign will turn off and the keypad lock
mode will be disengaged.
Using the product
Press the keypad lock button () to prevent
changing the refrigerator's temperature settings.
9. Eco-fuzzy
To activate the eco-fuzzy function, press and hold
the eco-fuzzy button for 1 second. When this
function is active, the freezer will switch to the
economic mode after at least 6 hours and the
economic use indicator will light up. To deactivate
the () eco-fuzzy function, press and hold the
eco-fuzzy function button for 3 seconds.
The indicator will light up after 6 hours when the
eco-fuzzy function is active.
10. Freezer compartment temperature setting
The temperature in the freezer compartment is adjustable. Pressing the button will enable the freezer
compartment temperature to be set at -18,-19,
-20, -21, -22, -23 and -24. ()
11. Rapid freezing
For rapid freezing, press the button; this will activate the rapid freezing indicator ().
When the rapid freezing function is turned on, the
rapid freeze indicator will light up and the freezer
compartment temperature indicator will display
the value -27. Press the Rapid freeze button (
) again to cancel this function. The Rapid freeze
indicator will turn off and return to normal setting.
The rapid freezing function will be automatically
cancelled after 24 hours, unless cancelled by the
user. To freeze a large amount of fresh food, press
the rapid freeze button before placing the food in
the freezer compartment.
20 / 33 EN
Refrigerator / User Manual
Using the product
1
2
3
4
56
7.2
7.1
8910
11
12
11
1
10.1
10.2
(*)
4
2
3
1. Freezer compartment temperature setting
2. Economy mode
3- Energy saving function (display off)