User Manual
VIRTUBE
VT250
2 x 50-Watt Guitar Amplier with 2 Independent Channels,
VTC Tube Modeling, Dual FX and 2 Original BUGERA 12" Speakers
VT100 /VT50
100/60-Watt Guitar Amplier with 2 Independent Channels,
VTC Tube Modeling, Dual FX and Original BUGERA 12" Speaker
VT100 H
100-Watt Guitar Amplier Head with 2 Independent Channels,
VTC Tube Modeling and Dual FX
2 VIRTUBE VT250FX/VT100FX/VT50FX/V T100FXH User Manual
Table of Contents
Thank you .......................................................................2
Important Safety Instructions ...................................... 3
Legal Disclaimer ............................................................. 3
Limited warranty ............................................................ 3
1. Introduction ............................................................... 4
1.1 Before you get started ...................................................... 4
1.1.1 Online registration ........................................................ 4
2. Control Elements ....................................................... 4
2.1 Front panel ............................................................................ 4
2.1.1 CLEAN CHANNEL ........................................................... 4
2.1.2 OVERDRIVE CHANNEL ................................................. 4
2.1.3 DIGITAL FX ....................................................................... 5
2.1.4 MASTER section ............................................................. 5
2.2 Rear panel ............................................................................. 5
2.2.1 FX LOOP ........................................................................... 5
3. Application Examples ............................................... 6
3.1 Set-up for practicing with playbacks ........................... 6
3.2 Recording set-up with eects device.......................... 6
3.3 Live set-up with external speaker box ........................ 7
3.4 Wiring the VT100FXH ........................................................ 7
4. Installation ................................................................. 8
5. Specications ............................................................ 9
Thank you
Congratulations! With the VIRTUBE, you have the newest generation of
guitar amps. It oers an extremely broad range of options and possibilities,
theonly limit being your own creativity. The VIRTUBE is an allrounder with so
many features that you hardly need any other equipment.
3 VIRTUBE VT250FX/VT100FX/VT50FX/V T100FXH User Manual
9. Do not defeat the safety purpose of the polarized
TO BIND MUSICGROUP BY ANY EXPRESS OR IMPLIED
Important Safety Instructions
Terminals marked with this symbol carry
electrical current of su cient magnitude
to constitute risk of electric shock.
Use only high-quality professional speaker cables with
¼" TS or twist-locking plugs pre-installed. Allother
installation or modi cation should be performed only
by quali edpersonnel.
This symbol, wherever it appears,
alertsyou to the presence of uninsulated
dangerous voltage inside the
enclosure-voltage that may be su cient to constitute a
risk ofshock.
This symbol, wherever it appears,
alertsyou to important operating and
maintenance instructions in the
accompanying literature. Please read the manual.
Caution
To reduce the risk of electric shock, donot
remove the top cover (or the rear section).
No user serviceable parts inside. Refer servicing to
quali ed personnel.
Caution
To reduce the risk of re or electric shock,
do not expose this appliance to rain and
moisture. The apparatus shall not be exposed to dripping
or splashing liquids and no objects lled with liquids,
suchas vases, shall be placed on the apparatus.
Caution
These service instructions are for use
by quali ed ser vice personnel only.
Toreduce the risk of electric shock do not perform any
servicing other than that contained in the operation
instructions. Repairs have to be performed by quali ed
servicepersonnel.
or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding-type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. Ifthe
provided plug does not t into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Use only attachments/accessories speci ed by
themanufacturer.
12. Use only with the
cart, stand, tripod, bracket,
or table speci ed by the
manufacturer, orsold with
the apparatus. When a cart
is used, use caution when
moving the cart/apparatus
combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to quali ed service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has
beendropped.
15. The apparatus shall be connected to a MAINS socket
outlet with a protective earthing connection.
16. Where the MAINS plug or an appliance coupler is
used as the disconnect device, the disconnect device shall
remain readily operable.
UNDERTAKING OR REPRESENTATION. THIS MANUAL
IS COPYRIGHTED. NO PART OF THIS MANUAL MAY
BE REPRODUCED OR TRANSMITTED IN ANY FORM
OR BY ANY MEANS, ELECTRONIC OR MECHANICAL,
INCLUDING PHOTOCOPYING AND RECORDING OF ANY
KIND, FOR ANY PURPOSE, WITHOUT THE EXPRESS
WRITTEN PERMISSION OF MUSICGROUPIPLTD.
ALL RIGHTS RESERVED.
© 2013 MUSICGroupIPLtd.
Trident Chambers, Wickhams Cay, P.O. Box 146,
Road Town, Tortola, British Virgin Islands
LIMITED WARRANTY
For the applicable warranty terms and conditions
and additional information regarding MUSIC Group’s
Limited Warranty, please see complete details online at
www.music-group.com/warranty.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including ampli ers) that produce heat.
LEGAL DISCLAIMER
TECHNICAL SPECIFICATIONS AND APPEARANCES
ARE SUBJECT TO CHANGE WITHOUT NOTICE AND
ACCURACY IS NOT GUARANTEED. BEHRINGER,
KLARKTEKNIK, MIDAS, BUGERA, AND TURBOSOUND
ARE PART OF THE MUSIC GROUP MUSICGROUP.COM.
ALL TRADEMARKS ARE THE PROPERTY OF THEIR
RESPECTIVE OWNERS. MUSICGROUP ACCEPTS NO
LIABILITY FOR ANY LOSS WHICH MAY BE SUFFERED
BY ANY PERSON WHO RELIES EITHER WHOLLY OR
IN PART UPON ANY DESCRIPTION, PHOTOGRAPH
OR STATEMENT CONTAINED HEREIN. COLORS AND
SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT.
MUSIC GROUP PRODUCTS ARE SOLD THROUGH
AUTHORIZED FULLFILLERS AND RESELLERS ONLY.
FULLFILLERSAND RESELLERS ARE NOT AGENTS OF
MUSICGROUP AND HAVE ABSOLUTELY NO AUTHORITY
4 VIRTUBE VT250FX/VT100FX/VT50FX/V T100FXH User Manual
(2) (17)
(1) (3)
(4) (5) (6) (7) (8) (10) (11) (12) (13) (14) (15) (16) (20) (21) (22) (23) (24) (25) (26)
(18) (19)
(9)
1. Introduction
The demands placed on a guitar amp are nowadays very broad. A guitarist should
oer a wide array of sounds. That’s why it is very important to us to be able to
oer you maximum sound diversity as well as a variety of connection possibilities
with your VIRTUBE. Don’t worry: you will quickly master the VIRTUBE and learn
how to use all of its capabilities easily and intuitively. With its up-to-date
circuitry, the VIRTUBE features the functionality and reliability of a truly modern
guitar amp.
VTC Virtual Tube Circuitry
The specially developed VTC Virtual Tube Circuitry gives your sound the unique
vintage avor of classic tube amps.
1.1 Before you get started
Your product was carefully packed at the factory to ensure safe transport.
Nevertheless, if the box is damaged inspect the unit immediately for signs
of damage.
◊ If the unit is damaged please do NOT return it to us, but notify your
dealer and the shipping company immediately; otherwise, claims for
damage or replacement may not be granted.
◊ Otherwise, always use the original box to prevent damage during
storage or transport.
◊ Make sure that children cannot play unsupervised with the unit or
its packaging.
Ensure adequate air supply and to avoid overheating do not place the unit
near radiators etc.
◊ Please make sure that all devices are properly grounded/earthed.
For your own safety, never remove or disable the ground/earth
conductors from the devices or on the power cords. The unit
must always be connected to the mains outlet with a protective
grounding connection.
1.1.1 Online registration
Please register your new BEHRINGER equipment right after your purchase
by visiting http://behringer.com and read the terms and conditions of our
warranty carefully.
Should your BEHRINGER product malfunction, it is our intention to have it
repaired as quickly as possible. To arrange for warranty service, please contac t
the BEHRINGER retailer from whom the equipment was purchased. Shouldyour
BEHRINGER dealer not be located in your vicinity, you may directly contac t
one of our subsidiaries. Corresponding contact information is included in the
original equipment packaging (Global Contact Information/European Contact
Information). Should your country not be listed, please contact the distributor
nearest you. A list of distributors can be found in the support area of our website
(http://behringer.com).
Registering your purchase and equipment with us helps us process your repair
claims more quickly and eciently.
Thank you for your cooperation!.
◊ Please ensure proper disposal of all packing materials.
Recylce whenever possible.
2. Control Elements
Fig. 2.1: VIRTUBE control elements (front panel)
2.1 Front panel
(1) The INPUT socket is the ¼" connector for your guitar. Please use a standard
¼" TS connector.
2.1.1 CLEAN CHANNEL
(2) The CLEAN CHANNEL LED lights up when the CLEAN channel is active.
(3) The GAIN control determines the volume of the CLEAN channel.
(4) The CRUNCH button (VT100FXH and VT100FX only) allows you to add some
slight distortion to your clean sound, giving it a bit of “dirt” or “crunch”.
(5) The BASS control in the EQ section allows you to raise or lower the bass
frequencies on the CLEAN channel.
(6) With the MIDDLE control you can raise or lower the midrange frequencies
onthe CLEAN channel.
(7) The TREBLE control adjusts the treble frequencies on the CLEAN channel.
(8) Press the CHANNEL button to switch between the CLEAN and OVERDRIVE
channels. The channel LED lights up when the channel is activated. With all
models you can also switch between channels using the footswitch provided.
2.1.2 OVERDRIVE CHANNEL
(9) The OVERDRIVE CHANNEL LED lights up when the channel is active.
(10) The GAIN control determines the amount of gain applied and hence the
degree ofdistortion in the OVERDRIVE channel.
(11) The OD1/OD2 button (VT100FXH and VT100FX only) switches between
twodierent overdrive sounds.
(12) The BASS control in the EQ sec tion allows you to raise or lower the bass
frequencies on the OVERDRIVE channel.
5 VIRTUBE VT250FX/VT100FX/VT50FX/V T100FXH User Manual
(13) With the MIDDLE control (VT100FXH and VT100FX only) you can raise or
lower the midrange frequencies on the OVERDRIVE channel.
(14) The TREBLE cont rol adjusts the treble frequen cies on the OVERDRIVE channel.
(15) Use the CONTOUR control for additional, highly characteristic adjustment
of the midrange, allowing you to easily create traditional as well
as ultra-modern guitar sounds.
(16) The VOLUME control adjusts the volume level of the OVERDRIVE channel.
2.1.3 DIGITAL FX
(17) The DIGITAL FX LED lights up when the eec ts processor is active.
(18) Use the FX PRESET control to select one of 16 eects.
Preset FX
1 - 4 Chorus/Delay
5 - 8 Delay
9 - 12 Chorus
13 - 16 Flanger
Tab. 2.1: Eect s
(19) The FX LEVEL control adjusts the mix ratio between the original and
the eect signal.
(20) The REVERB LEVEL control determines the eect intensity of the
additional reverb eect.
2.1.4 MASTER section
(22) The MASTER VOLUME control adjusts both the overall volume and
the line out/headphones volume.
(23) The V TC push button activates and deactivates the VTC Virtual Tube Circuitry.
(24) The CD IN connector allows you to connect the output signal of a CD player,
tape deck, or CD/MD walkman. For example, you can play back music CDs or
CDs accompanying a guitar tutor while practising. This connector can also
be used as a LINE OUT output. In this case, the guitar signal is output with no
speaker simulation applied and can be routed to an external amp or mixing
console. This will not mute the VIRTUBE’s built-in loudspeaker.
(25) The LINE OUT/PHONES jack is for headphones connection. Internal speaker
simulation is applied to the headphones signal in order to produce an
authentic signal. The VIRTUBE’s built-in loudspeaker is muted when this
connector is used.
◊ The headphones output signal can also be routed to a mixing console or
other sound reinforcement system. To do so, connect the headphones
output with the line input on the mixing console. Use a standard cable
with 1/4" TS connectors. If hum problems occur, you could insert a
DI box, e.g. BEHRINGER ULTRA-DI DI100 or DI120.
◊ Some headphones tend to produce distortion with too high
volume level. Please turn down the volume a bit, until distortion stops.
(26) The POWER switch turns your VIRTUBE on and o. It should always be in the
OFF position when connecting the unit to the mains.
(21) The FX LOOP MIX control (VT100FXH and VT100FX only) determines
the eect intensity of the external eect (see Chapter 2.2.1 FX LOOP).
(28)
(27) (29)
Fig. 2.2: VIRTUBE control elements (rear panel)
2.2 Rear panel
(27) The VIRTUBE is connected to the mains using a standard IEC receptacle.
A suitable power cord is included with the unit.
(28) FUSE HOLDER/VOLTAGE SELECTOR. Before connecting the unit to
the mains, ensure that the voltage setting matches your local voltage.
Blown fuses must be replaced with a fuse of the same type and rating.
On some units, the fuse holder can be switched to one of two positions,
i.e. 230 V and 120 V. Please note: when operating the unit outside Europe at
120 V, a higher fuse rating is required (see Chapter 4, “Installation”).
(29) This is where the fan of the unit is located.
(30) The SPEAKER OUT connectors (only one on the VT100FX and VT50FX)
can be used to connect external speakers with a miminum impedance of
4 Ω. The outputs of the VT250FX deliver 50 Watts of power per channel
◊ Please note: Merely switching the unit off does not mean that it is fully
disconnected from the mains. To disconnect the unit from the mains,
pull out the mains connector. Before installation, please make sure
that the mains connec tor has not been damaged. If you do not use the
unit for an extended period of time, please disconnect it at the mains.
(30) (35)
(33) (31) (32) (34)
(L/R). Always use speakers with a minimum impedance of 8 Ω to ensure
maximum power output. Using the SPEAKER OUT connectors will mute the
built-in loudspeakers.
2.2.1 FX LOOP
(31) The FX LEVEL button allows you to adapt the FX LOOP to the operating level
of an external eects device (+4 dBu/-10 dBV).
(32) The VIRTUBE provides a serial insert path for inserting external eects
(e.g. reverb processor). To do so, connect the FX SEND jack to the input of the
eects device.
◊ The FX SEND can also be used as a parallel output with no effects,
for example, to record a “dry” guitar signal. As long as the RETURN jack
is not in use, there will be no break in the internal signal path.
6 VIRTUBE VT250FX/VT100FX/VT50FX/V T100FXH User Manual
(33) Connect the FX RETURN jack to the output of the external eects device.
The VT250FX has two jacks (L/R) because it is a stereo amplier.
(34) Use the FOOTSWITCH jack to connect the ¼" TRS plug of the footswitch
supplied with the unit. The footswitch performs a dual function: it switches
between the two channels and turns the DIGITAL FX on and o.
(35) SERIAL NUMBER.
3. Application Examples
The VIRTUBE features plenty of connectors for a wealth of applications.
Here’s a few examples of how exible your VIRTUBE can be:
3.1 Set-up for practicing with playbacks
Footswitch
Drum Computer
HPS3000
3.2 Recording set-up with eects device
DSP2024P
FX In FX Out
FX Send FX Return
VIRTUBE VT100FX
DAT Recorder
Line Out
CD Player
VIRTUBE VT50FX
Fig. 3.1: VT50FX stand ard set-up
CD In
Electric Guitar
For practising in the rehearsal room or at home, please wire your VIRTUBE as
shown in Fig. 3.1. Connect a CD player or drum computer to the CD IN input.
If you want to practice with headphones, connect your headphones to the
PHONES jack. The built-in loudspeaker will be muted automatically. Connect the
dual footswitch supplied with the unit to the FOOTSWITCH jack on the VIRTUBE.
The CHANNEL footswitch switches between the channels. The EFFECT button
switches the eect on and o.
Footswitch
Electric Guitar
Fig. 3.2: Reco rding set-up with t he VT100FX
If you want to use your VIRTUBE in a home-recording or studio environment,
please wire it as shown in Fig. 3.2. Of course, you can still use a CD player
or drumcomputer in this set-up. This is not shown here to provide for a
better overview. Connect the input of the eects device to the FX SEND and
theeectsoutput tothe FX RETURN.
If you want to record your guitar signal with eects, connect the PHONES output
to your mixing console, audio sequencer or multi-track recorder.
To record a “dry” guitar signal with no eect, it is best to use the FX SEND
connector. You can use both outputs at the same time, for example, to record
signals via the FX SEND output (no eec t), while monitoring them via the PHONES
output (with eect).
Instead of an external 19" eects processor, you can also use a wah-wah pedal
orother stomp box. However, please note that the FX LOOP is post-preamp,
i.e. after the distortion stages.
7 VIRTUBE VT250FX/VT100FX/VT50FX/V T100FXH User Manual
3.3 Live set-up with external speaker box
BG412S
Mixing Console
Loudspeaker
Output Left
Loudspeaker
Output Right
GI100
3.4 Wiring the VT100FXH
The VT100FXH has two SPEAKER OUT outputs for connection of one or two
external speaker cabinets. To achieve maximum power output on the VT100FXH,
both speaker outputs should be connected to speaker cabinets with a minimum
impedance of 4 Ω. Connecting headphones to the PHONES jack will automatically
mute the speaker outputs.
VT100FXH
Loudspeaker
Output Right
VIRTUBE VT250FX
Footswitch
Electric Guitar
Fig. 3.3: Set-up co mprising VT25 0FX and one speaker bo x
Fig. 3.3 shows how the LINE OUT signal is routed to a mixing console. You can
connect external guitar speaker boxes to the SPEAKER OUT outputs of the
VIRTUBE (VT100FX and VT50FX have only one output) to achieve more power
and higher volume levels on stage. When the VT250FX is used, we recommend
connecting two separate speaker cabinets for stereo applications or one stereo
cabinet (e.g. BEHRINGER ULTRASTACK BG412S).
Loudspeaker
Output Left
Fig. 3.4:
VT100FX H with two speaker b oxes
Speaker Cabinets are 8 to 12 Ω each
8 VIRTUBE VT250FX/VT100FX/VT50FX/V T100FXH User Manual
4. Installation
Except for the headphones output and the CD IN input (¼" TRS connectors),
all audio inputs and outputs on the BEHRINGER VIRTUBE are on ¼" TS connectors.
Please see Chapter 5, “Specications” for more information.
◊ Please ensure that the unit is installed and operated only by people
qualified to do so. During installation and operation the user must have
sufficient electrical contact to earth. Electrostatic discharge may affect
the operation of the unit.
ring
tip
sleeve
sleeve
sleeve
R
L
tip
R
L
tip
Unbalanced ¼" TS connector
Fig. 4.1: ¼" TS connector
Balanced ¼" TRS connector
strain relief clamp
sleeve
tip
sleeve
(ground/shield)
tip
(signal)
strain relief clamp
sleeve
ring
tip
sleeve
ground/shield
Fig. 4.3: Stereo adapter cable
sleevesleeve
tiptip
Fig. 4.4: Mono adapter cable
ring
cold (-ve)
tip
hot (+ve)
For connection of balanced and unbalanced plugs,
ring and sleeve have to be bridged at the stereo plug.
Fig. 4.2: ¼" TRS conn ector
9 VIRTUBE VT250FX/VT100FX/VT50FX/V T100FXH User Manual
5. Specications
VT250FX
Audio Inputs
Input ¼" TS, RF ltered
Input impedance approx. 1 MΩ, unbalanced
FX Return 2 x ¼" TS
Input impedance approx. 33 kΩ, unbalanced
CD In ¼" TRS
Input impedance approx. 5.6 kΩ, unbalanced
Audio Outputs
FX Send ¼" TS
Output impedance approx. 5.6, kΩ unbalanced
Line Out / Phones ¼" TRS, unbalanced
Output level max. +16 dBV / 100 Ω
Loudspeaker Outputs
Type 2 x ¼"
Min. load impedance 2 x 8 Ω
Amplier
Power Supply
Power consumption max. 180 Watts
Fuse
100 V~, 50/60 Hz T 3.15 A H 250 V
120 V~, 50/60 Hz T 2.5 A H 250 V
220 - 230 V~, 50/60 Hz T 1.25 A H 250 V
Mains connection Standard IEC receptacle
Dimensions / Weight
Dimensions (H x W x D) 520 x 670 x 275 mm
(20.5 x 26.3 x 10.8")
Weight 22.2 kg (48.8 lbs)
Peak power 2 x 50 Watts / 8 Ω
Digital Signal Processing
Converter 24-bit, sigma-delta
Sample rate 40 kHz
Loudspeaker
Size 2 x 12"
Mode l BUGERA Vintage Guitar Series 2 x 12G50J8
Impedance 2 x 8 Ω
Continuous power (IEC268-5) 2 x 50 Watts
Peak power 2 x 200 Watts
10 VIRTUBE VT250FX /V T100FX/V T50FX/ VT100FXH User Manual
VT100FX
Audio Inputs
Input ¼" TS, RF ltered
Input impedance approx. 1 MΩ, unbalanced
FX Return ¼" TS
Input impedance approx. 33 kΩ, unbalanced
CD In ¼" TRS
Input impedance approx. 5.6 kΩ, unbalanced
Audio Outputs
FX Send ¼" TS
Output impedance approx. 8.2, kΩ unbalanced
Line Out / Phones ¼" TRS, unbalanced
Output level max. +16 dBV / 100 Ω
Loudspeaker Outputs
Type ¼"
Min. load impedance 4 Ω
Amplier
Power Supply
Power consumption max. 180 Watts
Fuse
100 V~, 50/60 Hz T 2.5 A H 250 V
120 V~, 50/60 Hz T 2.5 A H 250 V
220 - 230 V~, 50/60 Hz T 1.0 A H 250 V
Mains connection Standard IEC receptacle
Dimensions / Weight
Dimensions (H x W x D) 550 x 580 x 275 mm
(21.6 x 22.8 x 10.9")
Weight 20.4 kg (44.9 lbs)
Peak power 100 Watts / 4 Ω
Digital Signal Processing
Converter 24-bit, sigma-delta
Sample rate 40 kHz
Loudspeaker
Size 12"
Model BUGERA Vintage Guitar Series 12G70J4
Impedance 4 Ω
Continuous power (IEC268-5) 70 Watts
Peak power 280 Watts
11 VIRTUBE VT250FX/VT100FX/VT50FX/V T100FXH User Manual
VT50FX
Audio Inputs
Input ¼" TS, RF ltered
Input impedance approx. 1 MΩ, unbalanced
FX Return ¼" TS
Input impedance approx. 33 kΩ, unbalanced
CD In ¼" TRS
Input impedance approx. 5.6 kΩ, unbalanced
Audio Outputs
FX Send ¼" TS
Output impedance approx. 5.6, kΩ unbalanced
Line Out / Phones ¼" TRS, unbalanced
Output level max. +16 dBV / 100 Ω
Loudspeaker Outputs
Type ¼"
Min. load impedance 8 Ω
Amplier
Power Supply
Power consumption max. 90 Watts
Fuse
100 V~, 50/60 Hz T 1.6 A H 250 V
120 V~, 50/60 Hz T 1.25 A H 250 V
220 - 230 V~, 50/60 Hz T 630 mA H 250 V
Mains connection Standard IEC receptacle
Dimensions / Weight
Dimensions (H x W x D) 520 x 515 x 275 mm
(20.5 x 20.3 x 10.8")
Weight 16.5 kg (36.3 lbs)
Peak power 60 Watts / 8 Ω
Digital Signal Processing
Converter 24-bit, sigma-delta
Sample rate 40 kHz
Loudspeaker
Size 12"
Model BUGERA Vintage Guitar Series 12G50J8
Impedance 8 Ω
Continuous power (IEC268-5) 50 Watts
Peak power 200 Watts
12 VIRTUBE V T250FX/ VT100FX/ VT50FX/V T100FXH User Manual
VT100FXH
Audio Inputs
Input ¼" TS, RF ltered
Input impedance approx. 1 MΩ, unbalanced
FX Return ¼" TS
Input impedance approx. 33 kΩ, unbalanced
CD In ¼" TRS
Input impedance approx. 5.6 kΩ, unbalanced
Audio Outputs
FX Send ¼" TS
Output impedance approx. 8.2, kΩ unbalanced
Line Out / Phones ¼" TRS, unbalanced
Output level max. +16 dBV / 100 Ω
Loudspeaker Outputs
Type 2 x ¼"
Min. load impedance 4 Ω
Amplier
Power Supply
Power consumption max. 180 Watts
Fuse
100 V~, 50/60 Hz T 2.5 A H 250 V
120 V~, 50/60 Hz T 2.5 A H 250 V
220 - 230 V~, 50/60 Hz T 1.0 A H 250 V
Mains connection Standard IEC receptacle
Dimensions / Weight
Dimensions (H x W x D) 250 x 580 x 270 mm
(9.8 x 22.8 x 10.6")
Weight 12.7 kg (27.9 lbs)
BEHRINGER i s constantly str iving to maintain the h ighest profess ional standards. A s a result of these e ffort s,
modific ations may be made f rom time to time to exi sting product s without prio r notice. Specif ications and
appearance m ay differ fro m those listed or illus trated.
Peak power 100 Watts / 4 Ω
Digital Signal Processing
Converter 24-bit, sigma-delta
Sample rate 40 kHz
Loudspeaker
Size —
Model —
Impedance —
Continuous power (IEC268-5) —
Peak power —
We Hear You
Loading...