Behringer VM1 User Manual

VINTAGE TIME MACHINE VM1

Specications 3

Thank you for showing your condence in us by purchasing the BEHRINGER VINTAGE TIME MACHINE VM1. This high-quality classic
effect delivers true analog delay with up to 450 ms of organic echo to rival any tape delay, vibrant chorus and mind-bending vibrato.

Controls1.

The SERIAL NUMBER is located on the underside.

Use the {1} 9 V_ connection to plug in a 9 V power supply.
Use the {2} POWER switch to activate/deactivate the unit.
The {3} POWER LED lights up when the unit is activated.

The 1/4" TS {4} EFFECT OUT connector sends the signal to
your amp.

The 1/4" TS {5} DIRECT OUT connector always provides the
direct, unaffected signal to feed for example a separate
guitar amp.

Use this 1/4" TS {6} INPUT connector to plug in the instrument
cable.

The {7} CHORUS/VIBRATO switch selects between chorus or
vibrato effect.

The {8} LEVEL control adjusts the input level. The LEVEL control
adjusts the input level.

The {9} OVERLOAD LED illuminates when the input signal is
too high. In this case reduce the input level with the LEVEL
control.

The [10] MIX control adjusts the balance between the effect signal
and the direct signal.

The [11] FEEDBACK control determines the amount of signal
repetitions. Since the output signal is fed back to the input
of the delay line, it is possible to generate a self oscillation
at high settings of this control.

The [12] DELAY control adjusts the time between the direct signal
and the signal repetitions (Delay Time).

The [13] CHORUS/VIBRATO control adjusts the effects speed
of the modulation effect added to the delay. Slow settings
produce a chorus effect while fast settings provide vibrato.

Use the footswitch to activate/deactivate the effect.[14]

Sample settings2.

Warranty3.

For our current warranty terms, please refer to our website at http://www.behringer.com.

Specications4.

IN

Connector 1/4" TS

Impedance 100 kΩ

EFFECT OUT

Connector 1/4" TS

Impedance 1 kΩ

DIRECT OUT

Connector 1/4" TS

Impedance 100 kΩ

POWER SUPPLY

Power supply 9 V_, 100 mA (included)

BEHRINGER PSU-SB

Power connector 2 mm jack, negative center

Power consumption 50 mA

Dimensions (H x W x D) approx. 61 mm (2 2/5")

Weight approx. 1.07 kg (2.37 lbs)

BEHRINGER is constantly striving to maintain the highest professional standards.
As a result of these efforts, modications may be made from time to time to existing
products without prior notice. Specications and appearance may therefore differ from
those listed or shown.

x 200 mm (7 4/5")
x 172 mm (6 4/5")

FEDERAL COMMUNICATIONS
COMMISSION COMPLIANCE
INFORMATION

VINTAGE TIME MACHINE VM1

Responsible party name: MUSIC Group Services USA, Inc.

Address: 18912 North Creek Parkway,

Suite 200 Bothell, WA 98011,
USA

Phone/Fax No.: Phone: [phone]

Fax: [phone]

VINTAGE TIME MACHINE VM1

complies with the FCC rules as mentioned in the following paragraph:

This equipment has been tested and found to comply with the limits for a Class B
digital device, pur suant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful inter ference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful inter ference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:

Reorient or relocate the receiving antenna.•

Increase the separation between the equipment and receiver.•

Connect the equipment into an outlet on a circuit different from that to which the •
receiver is connec ted.

Consult the dealer or an experienced radio/T V technician for help.•

This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:

(1) this device may not cause harmful interference, and
(2) this device must accept any inter ference received, including inter ference that may
cause undesired operation.

Important information:

Changes or modifications to the equipment not expressly approved by MUSIC Group
can void the user ’s authority to use the equipment.

behringer.com