Behringer CP35 Quick Start Guide

Quick Start Guide

CP35 AT TENUATORS

Legendary Analog Attenuator and
Multiples Module for Eurorack

Controls

(1)

(3)

(4)

(1) IN and OUT JACKS – A si ngle input connec ted to the rst

attenua tor will pass to all 4 out puts. Addition al inputs
will break t he chain from the pr evious input. Fo r example,
input 1 will i nitially feed all 4 o utputs. If you add a s ignal
to input 2, th en input 1 will only fe ed output 1, and input 2
will feed o utputs 2, 3, and 4.

(2 ) ATTENUATOR KNOBS – Adjust th e level of the input

signal pas sively from -∞ to uni ty (0 dB).

(3 ) 6 VOLT OUTPUTS – Th ese outputs gi ve a reference

voltage of - 6 Volts on one outp ut pair, and +6 Volts on
the other pair.

(4 ) MULTIPLES – Connec t an input signal to on e of the 4-jack

secti ons, then send up to 3 cop ies of the same signa l to
other devices.

(2)

Power Connection

The module c omes with the requ ired power cable f or connecting
to a standa rd Eurorack power su pply system. Fol low these
steps to con nect power to the mo dule. It is easier to make th ese
connec tions before the m odule has been mou nted into a rack
case.

1. Turn the power su pply or rack case p ower o and
disconne ct the power cabl e.

2. Insert the 16- pin connector o n the power cable into t he
socket on t he power supply or rac k case. The connec tor has
a tab that wi ll align with the gap in t he socket, so it can not
be inser ted incorrec tly. If the power supply d oes not have
a keyed socke t, be sure to orient pi n 1 (-12 V) with the red
stripe o n the cable.

3. Insert the 10 -pin connecto r into the socket on th e back of
the module. T he connector has a t ab that will align wi th the
socket for correct orientation.

4. After both en ds of the power cable hav e been securely
attac hed, you may mount the mo dule in a case and tur n on
the power supply.

Installation

The neces sary screws ar e included with th e module for mount ing
in a Eurorac k case. Connect t he power cable bef ore mounting.

Dependi ng on the rack case, th ere may be a series of x ed holes
spaced 2 HP ap art along the leng th of the case, or a tra ck that
allows indi vidual threaded p lates to slide along th e length of the
case. The f ree-moving th readed plates allow p recise positi oning
of the modu le, but each plate shoul d be positioned in t he
approxim ate relation to the mo unting holes in your m odule
before attaching the screws.

Hold the mo dule against the Eur orack rails so that e ach of the
mounting h oles are aligned wi th a threaded rail o r threaded
plate. Att ach the screws par t way to start, w hich will allow small
adjustments to the positioning while you get them all aligned.
After th e nal position has b een establishe d, tighten the
screws d own.

Specications

Controls

Attenuators 4 x passive

rotary attenuators

Signal Input

Type 4 x 3.5 mm jack,

half normalled, DC coupled

Impedance < 25 kΩ, unbalanced

Maximum input level +20 dBu

Signal Output

Type 4 x 3.5 mm jack, DC coupled

Impedance < 25 kΩ, unbalanced

Maximum output level +20 dBu

Multiples

Type 8 x 3.5 mm TS mono jacks,

unbalanced

Arrangement 2 sets of 4

parallel jacks, passive

Compatibility CV and audio signals

6 V Voltage Re ferences

Negative 6 V output 2 x 3.5 mm jack, linked

Positive 6 V output 2 x 3.5 mm jack, linked

Impedance 5 kΩ

Power

Power supply Eurorack

Current draw 1 mA (+12 V), 1 mA (-12 V)

Physical

Dimensions 106 x 129 x 35 mm

(4.2 x 5.1 x 1.4")

Rack units 21 HP

Weight 0.18 kg (0.40 lbs)

LEGAL DISCLAIMER

Music Tribe accepts no liability for any loss which may be suered by any
person who relies either wholly or in part upon any description, photograph,
or statement contained herein. Technical specications, appearances and
other information are subject to change without notice. All trademarks are the
property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake,
Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Auratone
and Coolaudio are trademarks or registered trademarks of Music Tribe
Global Brands Ltd. © Music Tribe Global Brands Ltd. 2019 All rights reserved.

LIMITED WARRANTY

For the applicable warranty terms and conditions and additional information
regarding Music Tribe’s Limited Warranty, please see complete details online
at musictribe.com/warranty.

Zhongshan Eurotec Electronics Limited

No. 10 Wanmei Road, South China Modern Chinese Medicine Park,
Nanlang Town, 528451, Zhongshan City, Guangdong Province, China