Page 1
75.5779.01 JAMB CAM 20131115 Page 1 of 4
JAMB CAM
Low Profile, Door Jamb,
Color Video Camera
(US version)
ENGLISH
DESCRIPTION
TOOL
Power Drill
Tape Measurer
Magnetic Phillips #0
Phillips #2
1/8” Drill Bit
1 1/4” Drill Bit
Multimeter
Caulk & Caulking Gun
COMPONENTS REQUIRED TOOLS
DESCRIPTION PART NUMBER
CMOS Camera 12.1000
2.5 mm Lens 50.5277
Power/Video Harness 20.5316
Housing 70.5528
Housing Screws 50.1818
Camera Screws 50.5276
User’s Guide 75.5779
Mounting Template 75.5780
1. camera
2. housing
3. power supply / video harness
1
2
3
Page 2
Page 2 of 4 75.5779.01 JAMB CAM 20131115
The jamb cam focus is preset and is not adjustable.
The jamb cam must remain powered on when the door system is
powered off. Therefore, the jamb cam power supply must be wired to
an external transformer which is wired to the 120 VAC main power.
Shut off all power going to header before attempting any wiring procedures.
Maintain a clean & safe environment when working in public areas.
Constantly be aware of pedestrian trafc around the door area.
Always stop pedestrian trafc through the doorway when performing tests that may result in unexpected reactions by the door.
ESD (electrostatic discharge): Circuit boards are vulnerable to damage by electrostatic discharge. Before handling any board
ensure you dissipate your body’s ESD charge.
Always check placement of all wiring before powering up to ensure that moving door parts will not catch any wires and cause
damage to equipment.
Ensure compliance with all applicable safety standards (i.e. ANSI A156.10) upon completion of installation.
DO NOT attempt any internal repair of the components. All repairs and/or component replacements must be performed by
BEA, Inc. Unauthorized disassembly or repair:
1. May jeopardize personal safety and may expose one to the risk of electrical shock.
2. May adversely affect the safe and reliable performance of the product resulting in a voided warranty.
PRECAUTIONS
• The device should not be used for purposes other than its intended use. All other uses cannot be guaranteed by the
manufacturer of the sensor.
• The installer of the door system is responsible for carrying out a risk assessment and installing the sensor and the door system
in compliance with applicable national and international regulations and standards on door safety.
• The manufacturer of the sensor cannot be held responsbile for incorrect installations or inappropriate adjustments of the
sensor.
1
Only trained and
qualified personnel
may install and setup
the sensor.
The warranty is invalid if
unauthorized repairs are
made or attempted by
unauthorized personnel.
Always test the proper
operation of the
installation before
leaving the premises.
The door control unit
and the door cover
profile must be correctly
grounded.
SAFETY
Page 3
75.5779.01 JAMB CAM 20131115 Page 3 of 4
INSTALLATION
NOTE: Make sure power is OFF before installing jamb cams
1) Determine mounting location and apply mounting template to jamb
NOTE: For best results, horizontal center line of mounting template should be 54’’ from
ground
2) Predrill two (2) 1/8’’ mounting holes and one (1) 1 1/4’’ camera hole
3) Determine appropriate camera orientation and mount camera into housing
NOTE: If mounting on LEFT jamb, camera wire should lead towards housing window
(out of housing) and if mounting on RIGHT jamb, camera wire should lead away from
housing window (into housing)
4) Plug camera into power/video harness
5) Route power/video harness up jamb into door header
6) Connect RCA video out from power/video harness into appropriate RCA video in
7) Wire nut red and black power wires to external transformer
8) Fasten housing onto jamb with supplied screws
NOTE: If mounting in exterior application, apply a bead of silicone caulk to back of
housing
Power
Supply
RCA Video
Out (female)
Power In
(see specs)
Camera/Harness
JST
Page 4
Page 4 of 4 75.5779.01 JAMB CAM 20131115
Upon completion of the installation or service work, at a minimum, perform a daily safety check in accordance with the
minimum inspection guidelines provided by AAADM. Provide each equipment owner with an owner’s manual that
includes a daily safety checklist and contains, at a minimum, the information recommended by AAADM. Offer an
information session with the equipment owner explaining how to perform daily inspections and point out the location of
power/operation switches to disable the equipment if a compliance issue is noted. The equipment should be inspected
annually in accordance with the minimum inspection guidelines. A safety check that includes, at a minimum, the items
listed on the safety information label must be performed during each service call. If you are not an AAADM certified
inspector, BEA strongly recommends you have an AAADM certified inspector perform an AAADM inspection and place
a valid inspection sticker below the safety information label prior to putting the equipment into operation.
AAADM
American Association of
Automatic Door Manufactures
ANSI / AAADM Compliance
TECHNICAL SPECIFICATIONS
Power Supply 6.6 - 36 VDC (+/- 10%)
6 - 28 VAC (+/- 10%)
Operating Temperature -30° to 60° C (RH 95% max)
Video Output 1.0 (Vp-p) / 75Ω
Image Sensor CMOS
Horizontal Resolution 480 TVL
NTSC Output 720 (H) x 480 (V)
Sync System Inter-Sync
Frame Rate 30 fps
Minimum Illumination 0.01 LUX
AE Control Auto
Gain Control Auto
Electronic Shutter 1 s ~ 1/10,000 s
S/N Ratio >50 dB
AWB Auto
Specifications are subject to change without prior notice.
All values measured in specific conditions.
PLEASE KEEP FOR FURTHER USE - DESIGNED FOR COLOR PRINTING
©BEA | Original Instructions | 75.5779.01 JAMB CAM 20131115
24/7 Tech Support: 1-800-407-4545 | Customer Service: 1-800-523-2462 | General Tech Questions: Tech_Services@beainc.com | Tech Docs: www.beasensors.com
TROUBLESHOOTING
No image displaying
Power not connected Connect power wires
Power not correct Verify appropriate voltage
Bad camera Replace camera
Image upside down Camera rotated incorrectly Rotate camera 180 degrees
Distorted image
Power not correct (too low) Verify appropriate voltage, increase
Bad camera Replace camera
Dirty window Clean window
Loading...