Page 1
IXIO-ST
1
3
4
5
6
2
7
DESCRIPTION
Safety sensor
for automatic sliding doors
User’s Guide for product version 0403 and higher
See product label for serial number
ACCESSORIES
BA: Bracket accessory CA: Ceiling accessory
CDA: Curved door accessory
(according to EN 16005 and DIN 18650)
RA: Rain accessory
Download the BEA DECODER app
for a quick overview
of settings
9 V battery
ENGLISH
1. LCD
2. IR-curtain width adjustment
3. IR-lenses
4. cover
5. main connector
6. main adjustment knob
7. IR-curtain angle adjustment knob
Page 2
2
Pressing a parameter symbol on your remote control,
displays the saved value directly on the LCD-screen.
Do not unlock first.
HOW TO USE THE LCD?
To adjust contrast, push and turn
the grey button simultaneously.
During normal function only.
Push to
select
parameter
Scroll
menu
up-down
Select Back to
return to previous
menu or display.
Select More to go to
next level:
- basic settings
- advanced settings
- diagnostics
Negative display = active output
Select your language before
entering the first LCD-menu.
During the first 30 seconds after
power-on of the sensor or later in
the diagnostics menu.
CHANGING A VALUE
Scroll
values
up-down
Push
to save
new value
VALUE CHECK WITH REMOTE CONTROL
DISPLAY DURING NORMAL FUNCTIONING
FACTORY VALUE VS. SAVED VALUE
NAVIGATING IN MENUS
Scroll menu
items
Push to enter
the LCD-menu
new value is
displayed
more values are
displayed
current value is
displayed
displayed value = saved value
displayed value = factory value
Opening
impulse
Safety
6
6
Enter password if
necessary
Not during the first
minute after power-on
of the sensor.
CHANGING A ZIP CODE
Password
X
X X X
ZIP code
ZIP code
ZIP code
ZIP code
ZIP code
ZIP code
ZIP code
ZIP code
ID #
H24 1 56-KG4
01 0 800/02D
E24 1 56 KG4
01 0 800 02F
E24 1 56-KG4
01 0 800/02F
E24 1 56-KG4
01 0 800/02F
H24 1 56-KG4
01 0 800/02F
H24 1 56-KG4
01 0 800/02F
V
...
See application note on ZIP CODE
Validate the last digit in order to activate the new ZIP code:
- v = valid ZIP code, values will be changed accordingly
- x = invalid ZIP code, no values will be changed
- v/x = valid ZIP code, but from a different product.
Only available values will be changed.
Page 3
1
max. 5 cm
12-24 V
AC-DC
*
*
**
3
2
DIN 18 650
BS 7036
EN 160 05
3,50 m
3 m
2,50 m
2 m
d max = 2,5 m
d max = 3 m
3,50 m
3 m
2,50 m
2 m
d max = 2.5 m
max.
9 cm**
MOUNTING & WIRING
GREEN
BROWN
YELLOW
WHITE
PINK
GREY
RED
BLUE
POWER SUPPLY
OPENING INPUT
SAFETY INPUT
TEST
OUTPUT
* Output status when sensor is operational
** For compliance with EN 16005 and DIN 18650,
connection to door controller test output is required.
SENSOR
ENGLISH
IXIO-ST: INSTALLATION GUIDE
WIDTH
Additional
adjustments
are possible by
LCD or remote
control
(see p. 5)
Part of the detection field can be masked to reduce it.
The arrow position determines the width of the detection field.
INFRARED SAFETY FIELD
CLOSER
AWAY
If necessary, adjust the IR-curtain
angle (from -7° to 4°, default 0°).
Activate the visible* spots to verify
the position of the IR-curtain.
ANGLE
* Visibility depends on external conditions. When spots are not visible, use the Spotfinder to locate the curtains.
** The distance between the inner curtain of the inside door sensor and the inner curtain of the outside door sensor should
always be smaller than 20 cm. The distance to the door leaf depends therefore on the thickness of the door leaf.
The size of the detection field varies according to the
mounting height and the settings of the sensor.
The full door width must be covered.
Mounting
height
Detection
width
Always verify the actual detection field width
with a piece of paper and not the Spotfinder,
which detects the whole emitted field.
2.00 m
2.20 m
2.50 m
3.00 m
3.50 m
2.00 m
2.20 m
2.50 m
d max
d max
3.50 m
3 m
2.50 m
2 m
3.50 m
3 m
2.50 m
2 m
DOOR
TIP!
Wiring is compatible with the IRIS.
OR
Page 4
4
3
4
+
+
+
SETUP
TEST THE GOOD FUNCTIONING OF THE INSTALLATION BEFORE LEAVING THE PREMISES!
SETTINGS
OR
STANDARD: standard in- and outdoor installations
CRITICAL ENVIRONMENT: critical installations due to surroundings or weather
SHOPPING STREET: installations in narrow streets with pedestrian traffic
Choose one of the following presettings or adjust the sensor manually (see p.5):
SETUP 1 (QUICK)
SETUP 2 (ASSISTED)
OR
2 s
4 s
STEP OUT OF THE INFRARED FIELD!
reference picture
test of full door cycle +
reference picture
Page 5
1
2
A
B
+
0 1 2 3 4 5 6 7 8 9
5
OVERVIEW OF SETTINGS
Back
More
IR: WIDTH
IR: NUMBER
IR: PRESENCE TIME
IR: OUTPUT
REDIRECTION
FACTORY RESET
More
Back
Back
More
PRESETTINGS
IR: IMMUNITY
IR: FREQUENCY
More
Back
ZIP CODE all parameter settings in zipped format
(see application note on ZIP CODE)
ID # unique ID-number
ERROR LOG last 10 errors + day indication
IR: SPOTVIEW view of spot(s) that trigger detection
IR: C1 ENERG signal amplitude received on curtain 1
IR: C2 ENERG signal amplitude received on curtain 2
POWERSUPPLY supply voltage at power connector
OPERATINGTIME power duration since first startup
RESET LOG delete all saved errors
PASSWORD LCD and remotre control password
(0000= no password)
LANGUAGE language of LCD-menu
ADMIN enter code to access admin mode
standard
critical
env.
shopping
street
For conformity to EN 16005 or DIN 18650 at a
mounting height of 2.8 or more, use values 6 and 7.
For conformity to BS 7036 at a mounting height
of 2.2 m or more, use values 6 and 7.
Sensors mounted close to each other should
have a different frequency.
increased immunity
increased immunity, 1 curtain
factory values for IR immunity and IR number
service
mode
motion 15 s 30 s 1
min 2 min 5 min 10 min 20 min 60 min infinite
service mode = no IR detection during 15 minutes (maintenance).
This value excludes conformity of the door system to EN 16005 and DIN 18650.
min. value for DIN18650: 1 min
min. value for EN16005: 30 s
BASICADVANCED
DIAGNOSTICS
Always additionally adjust
the arrow position on the
sensor with a screwdriver.
excludes conformity of the door system
according to EN 16005 / DIN 18650 / BS 7036
NO
NC
NC
NC
NC
NO
NO
NO
NO: normally open
NC: normally closed
low
normal
high
normal
high
higher
highest
< 2.8 m > 2.8 m
full
reset
partial
reset
partial: outputs are
not reset
factory value
safety
safety
+
opening
0 presence detection on safety input
1 presence detection on safety and opening input
Page 6
2
1
4
5
1
2
1
2
1
2
1
1
1
2
1
2
1
2
1
1
2
1
2
6
8
1
E1
E2
E4
E5
E8
1
3
1
3
TROUBLESHOOTING
ORANGE LED flashes 1 x.
ORANGE LED flashes 2 x.
ORANGE LED flashes 4 x.
ORANGE LED is on.
RED LED flashes
quickly after an
assisted setup.
RED LED lights up
sporadically.
The LED and the LCDdisplay are off.
The reaction of the door
does not correspond to
the LED-signal.
The sensor signals
an internal fault.
The power supply is too
low or too high.
The sensor receives
not enough IR-energy.
The sensor encounters
a memory problem.
The sensor vibrates.
The sensor sees the door
during the assisted setup.
The sensor sees the door.
The sensor is disturbed
by external conditions.
Check power supply
(in the diagnostics menu of the LCD).
Check wiring.
Cut and restore power supply.
If orange LED lights up again, replace sensor.
Check output configuration setting.
Check wiring.
Check if the sensor is fastened firmly.
Check position of cable and cover.
Increase the IR-immunity filter to value 3.
Select presetting 2 or 3.
Launch an assisted setup and adjust the IR angle.
Replace sensor.
Check wiring.
ORANGE LED flashes 5 x.
The sensor receives
too much IR-energy.
ORANGE LED flashes 8 x.
IR power emitter is faulty.
Replace sensor.
The LCD or remote
control does not react.
Enter the right password. If you forgot the code, cut
and restore the power supply to access the sensor
without entering a password during 1 minute.
The sensor is protected by a
password.
The sensor is disturbed by
external elements.
Eliminate the cause of disturbance (lamps, rain cover,
door controller housing properly grounded).
Move the IR-curtains away from the door.
Install the sensor as close to the door as possible.
If needed, use a bracket accessory.
Launch a new assisted setup.
Decrease the angle of the IR-curtains.
Increase the IR-immunity filter (values >2.8 m).
Deactivate 1 curtain.
Slightly increase the angle of the IR-curtains.
Decrease the IR-immunity filter (values 1-3 <2.8 m).
Page 7
7
x
INSTALLATION
The sensor should be
fixed firmly to avoid
extreme vibrations.
Do not cover the sensor.
Avoid moving objects
and light sources in
the detection field.
Avoid highly
reflective objects in
the infrared field.
It is recommended to clean
the optical parts at least once
a year or more if required due
to environmental conditions.
Do not use aggressive
products to clean
the optical parts.
• The device cannot be used for purposes other than its intended use. All other uses cannot be
guaranteed by the manufacturer of the sensor.
• The manufacturer of the door system is responsible for carrying out a risk assessment and installing the
sensor and the door system in compliance with applicable national and international regulations and
standards on door safety.
• The manufacturer of the sensor cannot be held responsible for incorrect installations or inappropriate
adjustments of the sensor.
Only trained and
qualified personnel
may install and setup
the sensor.
The warranty is invalid if
unauthorized repairs are
made or attempted by
unauthorized personnel.
Always test the good
functioning of the
installation before
leaving the premises.
The door control unit
and the door cover
profile must be correctly
earthed.
MAINTENANCE
SAFETY
LED-SIGNAL
Presence
detection
LED flashes
LED flashes
quickly
LED is off
LED flashes
x times
LED flashes
red-green
Page 8
E
R
L
A
U
B
T
Z
E
R
T
I
F
I
Z
I
E
R
U
N
G
N
A
C
H
EN 16005
E
N
A
B
L
E
S
A
C
C
O
R
D
A
N
C
E
W
I
T
H
E
R
L
A
U
B
T
Z
E
R
T
I
F
I
Z
I
E
R
U
N
G
N
A
C
H
DIN 18650
E
N
A
B
L
E
S
A
C
C
O
R
D
A
N
C
E
W
I
T
H
BEA SA | LIEGE Science Park | ALLÉE DES NOISETIERS 5 - 4031 ANGLEUR [BELGIUM] | T +32 4 361 65 65 | F +32 4 361 28 58 | INFO@BEA.BE | WWW.BEA-SENSORS.COM
©BEA | Original instructions | 42.8338 / V3 - 10.16
BEA hereby declares that the IXIO-ST is in conformity with the basic requirements and the other relevant provisions
of the directives 2014/30/EU 2006/42/EC and 2011/65/EU.
Notified Body for EC-type inspection: 0044 - TÜV NORD CERT GmbH, Langemarckstr. 20, D-45141 Essen
EC-type examination certificate number: 44 205 12 405836-001
Angleur, April 2016 Pierre Gardier, authorized representative and responsible for technical documentation
The complete declaration of conformity is available on our website.
Only for EU countries: According to the European Guideline 2012/19/EU for Waste Electrical and Electronic Equipment (WEEE)
TECHNICAL SPECIFICATIONS
Supply voltage:
Power consumption:
Mounting height:
Temperature range:
Degree of protection:
Noise:
Expected lifetime:
Presence
Typical response time: < 200 ms (max. 500 ms)
Active infrared with background analysis
Spot: 5 cm x 5 cm (typ)
Number of spots: max. 24 per curtain
Number of curtains: 2
Solid-state-relay (potential and polarity free)
Max. contact current: 100 mA
Max. contact voltage: 42 V AC/DC
Holdtime: 0.3 to 1 s
Sensitivity: Low: < 1 V; High: > 10 V (max. 30 V)
Response time on test request: typical: < 5 ms
EN 12978; EN 61000-6-2; EN 61000-6-3; EN ISO 13849-1 PL «c» CAT. 2
(under the condition that the door control system monitors the sensor at least once per door cycle);
EN 62061; EN 61496-1 ESPE Type 2; EN 50581
EN 16005 Chapter 4.6.8; DIN 18650-1 Chapter 5.7.4; BS 7036-1 Chapter 8.1; EN 60825-1
Detection mode:
Technology:
Output:
Test input:
Norm conformity:
Specifications are subject to changes without prior notice.
All values measured in specific conditions.
12 V - 24 V AC +/-10% ; 12 V - 30 V DC +/-10% (to be operated from SELV compatible power supplies only)
< 2.5 W
2 m to 3.5 m
(local regulations may have an impact on the acceptable mounting height)
-25°C to +55°C; 0-95% relative humidity, non condensing
IP54
< 70 dB
20 years
PLEASE KEEP FOR FURTHER USE - DESIGNED FOR COLOUR PRINTING
Loading...