Page 1
75. 5835.0 4 FALCO N FAMILY 20160301 Page 1 of 4
FALCON
1
2
5
6
4
3
Specifications are subjec t to change s without prior notice.
* Other use of the devi ce is outside the permitted purpose and can not be guarantee d by the manufacturer.
** Measured in optimal conditions
TECHNICAL SPECIFICATIONS
DESCRIPTION
ENGLISH
Activation sensor for automatic industrial doors*
1. push buttons
2. front face
3. radar antenna
4. angle indication
5. bracket
6. cable
Technology:
Transmitter frequency:
Transmitter radiated power:
Transmitter power density:
Detection mode:
Detection zone:
Min. detection speed:
Supply voltage:
Mains frequency:
Max power consumption:
Output:
Max. contact voltage:
Max. contact current:
Max. switching power:
LED-signal:
Mounting height:
Degree of protection:
Temperature range:
Dimensions:
Tilt angles:
Materials:
Weight:
Cable length:
Norm conformity:
microwave doppler radar
24.150 GHz
< 20 dBm EIRP
< 5 mW/cm²
motion
FALCON: 13 x 16 ft @ 16ft ; FALCON XL: 13 x 6.5 ft @ 8.2ft;
FALCON WIDE: 30 x 11 ft @ 21 ft. (typical at 30° and field size 9)
2 in/s**
12V to 24V AC ±10%; 12V to 24V DC +30% / -10%
50 to 60 Hz
< 2 W
relay (free of potential change -over contact)
42V AC/DC
1A (resistive)
30W (DC) / 60VA (AC)
red: detection state, parameter indication; green: value indication
FALCON: 11.5 - 23 ft; FALCON XL: 6.5 - 11.5 ft; FALCON WIDE: 11.5 - 21 ft
IP65
from -22 °F to + 140 °F
5 in (L) x 4 in (H) x 3.75 in (W)
0° to 180° ver tical
ABS and polycarbonate
14 oz
33 ft
R&TTE 1999/5/EC; EMC 2004 /108/EC
FALCON: for normal to high mounting (11.5 - 23 ft)
FALCON XL: for low mounting (6.5 - 11.5 ft)
FALCON WIDE: for wide detection eld
For more information, please visit www.devancocanada.com
or call toll free at 855-931-3334
Page 2
Page 2 of 4 75. 5835. 04 FALCON FA MILY 2016 0301
1
1
2 3
2
COM
NO
NC
12-24 V
AC-DC
1
2
3
0-9
1-6
15°
30°
45°
+45°
XL
Position the sensor on the
bracket and fasten the screws
firmly.
FALCON
Mounting height: 16 ft
FALCON WIDE
Mounting height: 11.5 ft
FALCON XL
Mounting height: 8 ft
MOUNTING & WIRING
Adjust the angle of the sensor to position the detection field.
Remove the bracket
from the sensor.
Drill 2 holes accordingly.
Mount the bracket firmly.
Connect the wires to the door
controller. Choose between NO
and NC contact.
DETECTION FIELD ADJUSTMENTS
DETECTION FILTER
(REJECTION MODE)
Adjust the field size with the
remote control or the push
buttons.
All detection field dimensions were measured in optimal conditions and with field size value 9.
CEILING
WALL
Choose the right detection filter for your application with the remote control or the push buttons:
Value recommendations according to angle and height:
Detection of all targets
(pedestrians and parallel traffic are detected)
1 = no specific filter
2 = filter against disturbances
(recommended in case of vibrations, rain etc.)
Detection only of vehicles moving towards the sensor*
(pedestrians and parallel traffic are not detected + disturbances are filtered)
* The vehicle detection filter increases the response time of the sensor.
Always check if the chosen
value is optimal for the
application.
The obje ct size and nature
can influence the detection.
RED
BLACK
WHITE
GREEN
YELLOW
23 ft - 11.5 ft 8 ft
3 3
4 4
5 4
6 5
Page 3
75. 5835.0 4 FALCO N FAMILY 20160301 Page 3 of 4
XXS XS S > > > > L XL XXL
0.5 s 1 s 2 s 3 s 4 s 5 s 6 s 7 s 8 s 9 s
3 4
5 6
1
2
P
A
(7)
(0)
(1)
(2)
(1)
POSSIBLE SETTINGS BY REMOTE CONTROL
FIELD SIZE
OUTPUT
CONFIGURATION
A = active output (relay active when detection)
P = passive output (relay active when no detection)
DETECTION MODE
uni
AWAY
FACTORY VALUES
RESET TING TO FACTORY VALUES:
Avoid proximity to neon
lamps or moving objects.
Do not cover the sensor.
DETECTION FILTER
HOLD-OPEN TIME
Avoid vibrations. Only open the sensor
when the cable needs
to be replaced.
Wall mounting
Ceiling mounting
Ceiling mounting
Bracket dimensions
Bracket dimensions
TO START OR END AN ADJUSTMENT SESSION, press and hold either push button until the LED flashes or
stops flashing.
1 FIELD SIZE
Parameter n°
2 HOLD-OPEN TIME
3 OUTPUT CONFIGURATION
4 DETECTION MODE
5 DETECTION FILTER
Value (factory values)
TO SCROLL THROUGH THE
PARAMETERS, press
the right push button.
TO CHANGE THE VALUE OF
THE CHOSEN PARAMETER,
press the left push button.
TO RESET TO FACTORY VALUES, press and hold both push buttons until both LEDs flash.
POSSIBLE SETTINGS BY PUSH BUTTONS
MOUNTING TIPS
DIMENSIONS (inches)
bi = two-way detection
uni = one-way detection towards sensor
uni AWAY = one-way detection away from sensor
bi uni
Page 4
1
1
2
3
4
5
1
2
1
2
1
1
2
3
1
1
2
3
4
If you do not know the access code, cut and restore the power
supply. During 1 minute, you can erase an unkown access code:
BEA hereby declares that the FALCON is in conformity with the basic requirements and the other
relevant provisions of the directives 1999/5/EC and 2004/108/EC.
TROUBLESHOOTING
The sensor power is off.
Check the wiring and the power supply.
The complete declaration of conformity is available on our website: www.bea.be
The door opens
and closes
constantly.
The LED
flashes quickly
after unlocking.
The sensor does
not respond to the
remote control.
Improper output
configuration on the sensor.
The sensor is disturbed
by the door motion or
vibrations caused by the
door motion.
The sensor needs an access
code to unlock.
The remote control
batteries are weak or
improperly installed.
Check the output configuration setting on each
sensor connected to the door operator.
Check the batteries and change them
if necessary.
Make sure the detection mode is unidirectional.
Increase the detection filter value.
ACCESS CODE
SAVING AN ACCESS CODE:
DELETING AN ACCESS CODE:
The access code (1 to 4 digits) is recommended to set sensors installed close to each other.
The door remains
closed.
The LED is OFF.
The door does not
react as expected.
Make sure the sensor is fixed properly.
Make sure the detection mode is unidirectional.
Increase the tilt angle.
Increase the detection filter value.
Reduce the field size.
Enter the right access code.
If you do not know the access code, cut the power
supply and restore it to access the sensor and
change the access code or delete it.
Change the antenna angle.
Decrease the field size.
Increase the detection filter value.
The door opens for
no apparent reason.
The sensor detects raindrops
or vibrations.
In highly reflective
environments, the sensor
detects objects outside of its
detection field.
Only for EC countries: According the European Guideline 2012/19/EU for Waste Electrical and Electronic Equipment (WEEE)
SAFETY INSTRUCTIONS
The manufacturer of the door system is responsible for carrying out a risk assessment and installing the sensor and the door system in compliance with
applicable national and international regulations and standards on door safety.
Only trained and qualified personnel may install and setup the sensor.
The warranty is void if unauthorized repairs are made or attempted by unauthorized personnel.
The vehicle detection
filter is used, but
pedestrians are still
detected.
The chosen value is not
optimal for this application.
Increase the detection filter value.
Decrease the sensor angle.
Increase the installation height.
Make sure the detection mode is unidirectional.
ERASE AN UNKOWN ACCESS CODE:
Once you have saved an access code, you always need to enter this code to unlock the sensor.
For more information, please visit www.devancocanada.com or call toll free at 855-931-3334
Loading...